Tailgate Grill Model: SC SC-00 Instruction Manual

Transcription

1 Tailgate Grill Model: SC SC-00 Instruction Manual For Outdoor Use Only Tools needed for assembly and maintenance: Phillips Screwdriver & Adjustable Wrench (Not Included) This instruction manual contains important information necessary for the proper assembly and safe use of the appliance. Read and follow all warnings and instructions before assembling and using the appliance. Keep this manual for future reference. SC SC-00 - ENG 1 of V1

2 If you smell gas: DANGER 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. Open Lid. 4. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department. Failure to follow these instructions could result in fire or explosion which could cause property damage, personal injury or death. DANGER 1. Never operate this appliance unattended. 2. Never operate this appliance within 10 ft (3.05 m) of any structure, combustible material or other gas cylinder. 3. Never operate this appliance within 25 ft (7.5 m) of any flammable liquid. 4. If a fire should occur, keep away from the appliance and immediately call your fire department. Do not attempt to extinguish an oil or grease fire with water. Failure to follow these instructions could result in fire or explosion which could cause property damage, personal injury or death. WARNING Combustion by-products when using this product contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. SC SC-00 - ENG 2 of V1

3 Please read Safety and Precaution statements, Grill Maintenance, Leak Testing, Regulator/ Cylinder connection and Lighting Instructions before using grill the first time. Safety Symbols The symbols and boxes shown below explain what each heading means. Read and follow all of the messages found throughout the manual. DANGER Danger: Indicates an imminently hazardous situation which, if not avoided, will result in serious injury or death. WARNING Warning: Indicates a potentially hazardous situation which, if not avoided, will result in serious injury or death. CAUTION Caution: Indicates a potentially hazardous situation or unsafe practice which, if not avoided, may result in minor or moderate injury. WARNING The appliance shall not be used on or under any apartment or condominium balcony or deck. The appliance shall be used outdoors only, and shall not be used in a building, garage or any other enclosed area. This appliance is not intended to be installed or used in or on a recreational vehicle or boat. The appliance shall maintain minimum 36 Inches (91.4cm) from combustible materials to the sides and back SC SC-00 - ENG 3 of V1

4 of the appliance, and the appliance shall not be located or used under overhead unprotected combustible materials. This appliance is for outdoor use only and should only be operated in a well-ventilated space. Never operate in an enclosed space, garage or building. This appliance is not intended for commercial use. This appliance is not for frying turkeys. When cooking, the appliance must be on a level, stable noncombustible surface in an area clear of combustible material. An asphalt surface is not acceptable for this purpose. Do not leave the appliance unattended. Keep children and pets away from the appliance at all times. This appliance is not intended for and should never be used as a heater. This appliance will be hot during and after use. Use insulated oven mitts or gloves for protection from hot surface. Never attempt to attach this appliance to the self-contained LP gas system of a camper trailer or motor home. Carefully follow all instructions in this manual for proper assembly and leak testing. Do not use appliance until leak test has been completed. If leak is detected at any time, turn OFF gas supply and do not use until leak source has been corrected. Cooking area should be kept clear and free from combustible materials, gasoline, bottled gas in any form, and any other flammable vapors and liquids. Keep free of obstructions that would prevent ventilation. Never try to light appliance with lid closed. The buildup of gas is very dangerous and could cause an explosion. The use of alcohol, prescription or non-prescription drugs may impair your ability to properly assemble or safely operate the appliance. Do not move appliance when in use. Allow the appliance to cool down completely before moving or storing. USE OF LP GAS CYLINDER AND INSTALLATION BEFORE INSTALLING: LP GAS CYLINDER The installation must conform with local codes or, in the absence of local codes,with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58; or Natural Gas and Propane Installation Code, CSA B149.1;Propane Storage and Handling, CSA B149.2; or the Standard for Recreational Vehicles, ANSI A119.2/NFPA 1192; and Recreational Vehicle Code, CSA Z240 RV Series, as applicable. The LP-gas supply cylinder to be used must be constructed and marked in accordance with the specifications for LP-gas cylinders of the US Department of Transportation (DOT) or the National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods. SC SC-00 - ENG 4 of V1

5 This appliance is designed to operate with a one pound 7.75 or 10.6 high disposable / 16.4 oz. or 14.1 oz. propane gas cylinder (DOT 39 Cylinder) Do not attempt to refill any disposable propane gas cylinders. The cylinder must be installed, transported and stored in an upright position and should not be dropped or handled roughly. When the appliance is to be stored indoors, the propane gas cylinder must be disconnected from the appliance. When the propane gas cylinder is connected to the appliance, both must be stored outdoors in a well-ventilated space. The propane gas cylinder should never be transported or stored where temperatures can reach 51.C (124.F) Cylinders must be stored outdoors out of the reach of children and must not be stored in a building, garage, or any other enclosed area. The propane gas cylinder supply system must be arranged for vapor withdrawal. Disconnect the gas propane cylinder when not in use. CONNECT THE PROPANE GAS CYLINDER Only cylinders marked propane may be used. Note: Some 1lb cylinders may form frost when near empty. 1. Make sure the control knob is in OFF position. 2. Lubricate the threads of the regulator with petroleum jelly if necessary. Line up threads on LP gas cylinder with regulator. 3. Insert and rotate LP gas cylinder clockwise until they fit snugly together. HAND TIGHTEN ONLY. Be careful not to cross threads when screwing in the cylinder. Test for leaks, see Leak Test Section. CAUTION (a) Do not store a spare LP-gas cylinder under or near this appliance; (b) Never fill the cylinder beyond 80 percent full; and (c) If the instructions in (a) and (b) are not followed exactly, a fire causing death or serious injury may occur. LEAK TEST Although all gas connections on the grill are leak tested at the factory prior to shipment, a complete gas tightness check must be performed at the installation site due to possible mishandling in shipment, or excessive pressure unknowingly being applied to the unit. SC SC-00 - ENG 5 of V1

6 Periodically check the whole system for leaks following the procedures listed below. If the smell of gas is detected at any time you should immediately check the entire system for leaks. BEFORE TESTING Make sure that all packing material is removed from the grill including the burner tie-down straps. Prepare a soap water mixture of one part liquid detergent and one part water. You will need a spray bottle, brush, or rag to apply the solution to the fittings. For the initial leak test, make sure the LP cylinder is available and never fill the cylinder beyond 80 percent full. WARNING DO NOT SMOKE WHILE CONDUCTING LEAK TEST NEVER PERFORM LEAK TEST WITH AN OPEN FLAME If it is evident there is excessive abrasion or wear, or the regulator is damaged, it must be replaced prior to the appliance being operational. The replacement regulator shall be specified the by manufacturer. TO TEST 1. Make sure the control knobs are in the OFF position, and turn on the gas supply. 2. Check all connections at the Gas cylinder, LP gas regulator and supply valve up to and including all connections to the pipe that go to the burners (the diagram shows the point where the soap water mixture is being applied). Soap bubbles will appear where a leak is present. 3. If a leak is present, immediately turn off the gas supply and tighten the leaky fittings. 4. Turn the gas back on and recheck. 5. If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior to the outdoor cooking gas appliance being put into operation. The replacement hose assembly shall be that specified by the manufacturer. Contact customer service at (888) Points of leak test: 1. Connection point at the manifold and the regulator outlet. 2. Connection point at regulator and tubing. 3. Connection point at the Gas cylinder outlet and regulator inlet. 4. Connection points at control valves and manifold. ( Under the Control panel) SC SC-00 - ENG 6 of V1

7 Product Diagram SC SC-00 - ENG 7 of V1

8 Component List 1. Lid Handle 2. Lid Handle Bracket 3. Grill Body Assembly 3e 3b 3c 3f 3a 3d 1 pc 2 pcs 3a: Grill body with hose regulator assembly - 1 pc 3b: Grill lid 1pc 3c: Legs 1set 3d: Control knob 2pcs 3e: Lighting rod 1pc 3f: Lid lock 1pc 3. Grill Lid Assembly 3. Grill Bottom Body Assembly 4. Cooking Grate (Left) 3g 3j 3k 3h & 3i 3g: Heat shield 1pc 3h: Hinge (top) 2pcs 3i: Hinge (bottom) 2pcs 3j: Steel bracket (front) 2pcs 3k: Steel bracket (back) 2pcs 3l: Silica washer 12 pcs 1 pc 5. Cooking Grate (Right) 6. Flame Tamer 7. Side Table 3l 3l 7a 1 pc 2 pcs 7a: Side table - 1pc 7b: Lock assembly 1pc 8. Wheel 10. Wheel Cover 10. Oil Drip Tray 7b 2 pcs 2 pcs 1 pc SC SC-00 - ENG 8 of V1

9 11. Plastic Leg Base 2 pcs Hardware List Item No. Item Name Diagram Qty. #A Wheel Bolt 2 pcs #B M10 Washer 2 pcs #C M6 * 15mm Bolt 4 pcs #D M6 Washer 4 pcs #E M6 * 55mm Bolts 2 pcs #F Cotter Pin 4 pcs SC SC-00 - ENG 9 of V1

10 Assembly Procedures Step 1. Take out the Grill Body (3) from the packing box and keep the grill body in folded position. Loosen the screws on legs as following. Insert these screws through the center hole of the Plastic Leg Base(11) and tighten them firmly. 3 Screws on legs Step 2. Insert the Wheel Bolt (#A) through the Wheel (8) and Washer (#B) and then tighten the bolt to the leg frame of Grill Body (3). Attach the Wheel Cover(9) to the Wheel (8). #A 9 8 #B 3 #B 8 #A Wheel Bolt x 2 pcs #A 9 #B Washer x 2 pcs SC SC-00 - ENG 10 of V1

11 Step 3. Unfold the Grill as per following figure. Step 4. Attach Side Table (7) to Grill Body by using 4 pcs of M6x15mm Bolt (#C) and M6 Washer (#D). 7 #C + #D #C + #D #C M6x15mm Bolt x 4 pcs #D M6 Washer x 4 pcs SC SC-00 - ENG 11 of V1

12 Step 5. Insert M6x55mm Bolts (#E) through the Lid Handle Brackets (2) and Lid Handle (1). Tighten the the Handle firmly. 1 2 #E 3 #E - M6x55mm Bolt x 2 pcs Step 6. Place the Flame Tamer (6) over the burners and use 4 pcs of Cotter Pins (#F) to maintain the Tamers position. 6 #F #F Cotter Pin x 4 pcs SC SC-00 - ENG 12 of V1

13 Step 7. Place the Cooking Grates (4 and 5). 4 and 5 Step 8. Attach the Oil Drip Tray (10) under the Grill Body. 10 Before Cooking for the First Time Assembly is completed!!! Operate grill 15 minutes with grill lid closed and gas control on HIGH. This will heat-clean internal components and eliminate odor of oil in grill. WARNING Always unfold the grill completely during cooking and lighting SC SC-00 - ENG 13 of V1

14 Unfold Grill Note: Unlock the latch before unfolding the legs Fold Grill WARNING Propane Gas Cylinder MUST be detached from regulator before folding the grill DO NOT fold the grill or move the grill immediately after cooking. Wait for the grill to cool down completely! Note: Side table should be completely folded before moving the grill Lock the latch before moving the grill. SC SC-00 - ENG 14 of V1

15 Fold / Unfold Side table Pull the latch Pull the latch Lighting Instructions 1. Read all instructions before lighting 2. Open lid during lighting 3. Make sure the propane gas cylinder is tightly threaded into the regulator (hand tighten only). 4. Push and turn main burner knob slowly to HI. 5. Press the ignitor button. If ignition does not occur in 5 seconds, turn the regulator knob off, wait 5 minutes and repeat the lighting procedure Manually Lighting Your Grill By Match 1. Important! OPEN LID. Attempting to light burner with lid closed may cause an explosion. Do not expose any part of your body or clothing directly above cooking area when lighting.. 2. Using the lighting rod with a match, ignite the match and insert through the cooking grates to the burners. 3. While holding match in place, turn control knob to Hi position. Burner will ignite. 4. Observe burner flames through openings at flame tamer. Make sure burner ignites and stays lit on both sides. Lighting Rod Match 5. If ignition does not occur in 5 seconds, turn the regulator knob off, wait 5 minutes and repeat the lighting procedure. SC SC-00 - ENG 15 of V1

16 CAUTION 1. If burner does not light OR if burner flame is accidentally extinguished, turn control knob on regulator to OFF, wait 5 minutes, try again. If the burner does not ignite with valve open OR if burner flame is accidentally extinguished after lighting, gas will continue to flow out of the burner and could accidentally ignite with risk of injury. 2. Handle temperatures with grill on HIGH will be too HOT to touch with bare hands. Use hot pads or mitts to handle the grill when hot. Turning grill off After cooking, turn the grill off by rotating the control knob to OFF. Control knob should pop up in the OFF position. If control knob does not pop up, disconnect cylinder to turn grill off and replace the regulator. This appliance will be hot during and after use. Use insulating oven mitts or gloves for protection from hot surface or splatter from cooking liquids. Allow grill to cool completely before storing. Storing your grill Be sure the appliance has cooled. Remove propane cylinder and install protective cap over outlet threads. Disconnect the propane gas cylinder when not in use. SC SC-00 - ENG 16 of V1

17 Natural Hazards -Insects and Spiders WARNING A clogged tube can lead to a fire beneath the appliance. During shipment or storage, it is possible that small Insects and spiders could find their way into the venturi tubes and make nests or webs. This could block the flow of gas through the venturi tube causing a smoky, yellowish flame, or prevent a burner from lighting. It could even cause the gas to burn outside the venturi tube, which could seriously damage the appliance. If this occurs, turn off the gas flow and wait for the appliance to cool. When the appliance has cooled, remove the burner and clean out the venturi tube with a brush or pipe cleaner. Replace the burner and be sure that the venturi tube is seated over the orifice located on the gas valves. Cleaning of the venturi tube should be conducted periodically, especially at the start of the season. Note: Damage resulting from blocked venturi tube is not covered under warranty. Flame Characteristics Check for proper burner flame characteristics. Burner flames should be blue and stable with no yellow tips, excessive noise or lifting. The following steps should be followed for correcting the flame characteristics: Turn the control knobs and Liquid Propane cylinder valve OFF Allow the grill and burners to cool. If the flame is yellow (not enough air), turn the adjustment screw found at the front of the burner counterclockwise. Appox. 1/2 inches If the flame is noisy or lifts away from the burner (too much air), turn the adjustment screw found at the front of the burner counterclockwise. If these adjustments do not correct the problem, contact customer service at (888) Grill Maintenance Clean and inspect pressure regulator and hose assembly prior to use. Allow grill to cool before cleaning. Frequency of cleaning is determined by how often grill is used. DO NOT use self-cleaning oven to clean any grill part. Extreme heat would remove any chrome plating and cause premature rusting. Meal drippings will solidify in bottom of grill after a few uses. This residue should be removed regularly. Failure to do so could cause overflow at bottom vent openings and increase the chance of a grease fire. When cleaning grill, cover work area with newspaper. Open grill lid and remove cooking grate. Loosen residue with scraper or putty knife. Wipe away loosened residue with paper towels. Inside surface of grill may be cleaned with a strong solution of detergent and water applied with a scrub brush. Cooking grate may be cleaned with a brass wire brush. Thoroughly rinse grill with water and allow to completely air-dry before using again. Place cooking grate and lid onto grill. Check and clean burner/venturi tubes for insects and insect nests. A clogged tube can lead to a fire beneath the appliance. Do not obstruct the flow of combustion and ventilation air. SC SC-00 - ENG 17 of V1

18 Burner Cleaning Before cleaning, make sure the gas supply and control knobs are in the OFF position and the burners have cooled. To remove the main burners for cleaning: 1. Open lid. Remove the cooking grate and flame tamer. 2. Remove the screws and ignition electrode wire, lift the burner out of the firebox to clean the grill burners. 3. Clean the exterior of the burner with a wire brush. Use a metal scraper for stubbed stains or debris. 4. Clear clogged ports with straightened paper clip. Never use a wooden toothpick as it may break off and clog the port. 5. Check and clean burner / venturi tubes for insects and insect nests. A clogged tube can lead to a fire beneath and behind the main control panel. To reinstall the main burners: 1. Insert the burner over the main burner gas valve. 2. Make sure the orifice spud (A) is inside the burner venturi (B) 3. Align the burner screw hole with the firebox hole, insert screw and tighten. Screw Clean the burner Burner Orifice spud (A) Burner Venturi (B) Control Valve Should you encounter any problem, need assistance with assembly, have questions about this product or have missing or defective parts, Please contact Customer Service at Rankam Metal Products Manufactory Limited Monday thru Friday 8 A.M. to 5 P.M. Western Standard Time or by customerservice@rankam.com WE CAN HELP. Made in China SC SC-00 - ENG 18 of V1

19 LIMITED WARRANTY 1. Manufacturer warrants this Product to be free from defects in workmanship and materials for a period of 90 days from the date of purchase, PROVIDED claims are submitted, in writing, with proof of purchase. 2. If any part of this item fails because of a manufacturing defect within the Limited Warranty Period, Manufacturer offers to replace such part(s) provide that such parts have not been improperly repaired, altered, or tampered with or subject to misuse, abuse or exposed to corrosive conditions. This Limited Warranty is, however, subject to certain limitations, exclusions, time limits and exceptions (Hereinafter Conditions ) as listed below. Read these Conditions carefully. 3. This Limited Warranty shall be limited to the replacement or repair of any part(s) which Manufacturer determines, after reasonable examination, to have been defective at the time of manufacturing and manufacturer s obligation(s) shall be limited to replacement, if any, of defective part(s) which shall be shipped at Original Purchaser s expense to Original Purchaser s designated shipping address. 4. This Limited Warranty is given to and covers the ORIGINAL PURCHASER ONLY and such coverage terminates 90 days from the date of purchase. 5. DAMAGE LIMITATION WARNING: IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR ANY INCIDENTIAL OR CONSEQUENTIAL DAMAGES, INCLUDING (BUT NOT LIMITED TO) LOSS OF USE OF THE PRODUCT, LOSS OF TIME, INCONVENIENCE, EXPENSES FOR TRAVEL, TRANSPORTATION, LODGING EXPENSES, LOSS OF FOOD, LOSS BY DAMAGE TO PERSONAL PROPERTY OR LOSS OF INCOME, PROFITS OR REVENUE. 6. MANUFACTURER S OBLIGATION: Manufacturer s liability shall be limited to the delivery of a good, merchantable Product and, if necessary, the repair or replacement, at manufacturer s option, of any defective part or unit. 7. TRANSFER LIMITATIONS: This Limited Warranty is not assignable or transferable. It covers only the original purchaser. 8. RESERVED RIGHT TO CHANGE: Manufacturer reserves the right to make changes or improvements to products it produces in the future without imposing on itself any obligations to install the same improvements in the products it has previously manufactured. 9. This Limited Warranty gives the Original Purchaser specific legal rights but there may be other rights which vary by jurisdiction. 10. This warranty does not cover the following items: Chips or scratches on porcelain or painted surfaces Rust or corrosion is not deemed a manufacturing or materials defect Discoloration or loss of paint due to handling during assembly, heat or cleaning products. Paint may require touch up. Stainless steel discoloration or corrosion Consumables such as batteries IF CUSTOMER SERVICE IS NECESSARY: 1. The Original Purchaser is responsible for shipping and handling charges of the returned item(s) and replacement parts, if any. 2. All parts to be replaced will need to be shipped before replacement items will be sent. 3. Follow the Customer Service Representative s instructions exactly. If a return is necessary, it must be packed carefully and shipped prepaid. Rankam Metal Products Manufactory Limited 1618 W. Rosecrans Ave., Gardena, CA90249 USA SC SC-00 - ENG 19 of V1