DISCONTINUED. Widespread Lavatory Faucet TL170DD RENESSE. Contents. Installation and Owner s Manual. English Español Français

Transcription

1 0GU TL170DD Widespread Lavatory Faucet Installation and Owner s Manual RENESSE Español Français Contents Important Safeguards Specifications Before Installation Components Set-Up Drawing Installation Procedure ~10 Maintenance ~13 Troubleshooting Replacement Parts Warranty Thank you for your recent purchase of the TOTO product. Please read the enclosed information to ensure the safe use of your product..

2 Important Safeguards (For your safety, please follow the instructions below) Read the Important Safeguards section thoroughly before installing the product. The following symbols indicate safe and proper use of the product. Failure to observe them may reult in injury or property damage. The following table demonstrates the use of safety symbols in this manual. Do Not Warning Caution Do not disassemble Do not Touch Failure to observe this symol may result in serious injury. Failure to observe this symbol may result in injury or property damage. Warning Do not reverse the hot and cold water inlets. You may be scalded if they are reversed. Do not use hot water supply that is higher than 185 F (85 C). Do not use steam as hot water supply. If water is hotter than 185 F is used. If it is broken, property damage, scalding, and other injuries may occur. Do not disassemble or modify the item in any way not described in this manual. If the system is broken, property damage, scalding and other injuries are likely to occur. While using hot water, do not touch the spout and escutcheon directly. and seat may cause scalding when they are hot. Caution Absolutely Do NOT. Do not disassemble Mandatory! C Cold water escutcheon H Hot water Less than185 F (85 C) Do not strike or kick the product. HOT Do Not If the system is broken, property damage, scalding, and other injuries may occur. Do not use the product at temperature exceeding what local codes allow. If parts are damaged, property damage, scalding and other injuries may occur. Freezing 1

3 Specifications Cold and hot water pressure Minimum pressure Maximum pressure Supplied Water Temperature Suitable Water Quality Suitable ambient temperature Supply Connection Flow rate Before installation 20 psi (0.14MPa) (flowing pressure) 125 psi (0.86MPa) (static) Less than 185 F (85 C) Water that meets National/Primary drinking water regulation 34 F?104 F (2 C~40 C) 3/8 NPSM Max. 2.2 gpm (8.32 L/min) If the water supply pressure is higher than 125psi (0.86MPa), you should buy a reducing valve to reduce the pressure to the range of MPa. To use the faucet comfortably, the recommended pressure is about psi ( MPa). To prevent being scalded due to malfunction, the cold water supply pressure must be higher than the hot water pressure, or you can make them equal. In addition, if you increase the pressure of the hot water, it still must be lower than that of cold water supply side. To prevent being scalded due to wrong operation, it is recommended the hot water supply temperature is 140 F (60 C). To reduce resistance, the pipe that is connected to the hot water device should be as short as possible, and the pipe should be wrapped with insulating material. For ease of water flow adjustment and inspection with tools, you should prepare an extra stop valve. You may find residual water in the product ; this is due to water test for quality assurance before packaging. 2

4 Components - Observe all local plumbing codes. -Make sure that water supply is shut off. -Read these instructions carefully to ensure proper installation. -For new lavatory installation, install the faucet before installing the lavatory Confirm package includes following parts. Some parts may be different depending on the model Shank Assembly Flat washer (small) Lock washer (small) shank mounting nut Flat packing Winged packing Parts spout mounting flange Flat washer (big) Lock washer (big) mounting nut Handle escutcheon (HOT) Other Handle Parts Handle cap Screw Handle Bush Hex nut Spacer Handle cap Screw Handle Bush Hex nut Spacer Handle escutcheon (Cold) Valve Body Parts H label Valve body assembly (hot side) gasket packing (white) packing (black) C label Valve body assembly (cold side) gasket packing (white) packing (black) slip washer slip washer fastening nut fastening nut 3 Give these to Customer! Installation and Operation Manual key connector packing connector packing

5 Set-Up Drawing *Some parts may differ from the illustration depending on the model. counter hole Dia. 1-5/16-1-7/16 (φ35±2 mm) 25-5/16 (642 mm) HOT CLOSED 8 (203mm) OPEN 1-3/4 (44mm) 3/8 NPSM 8-9/16 (218 mm) 3 (76 mm) OPEN 7 (177mm) 1-1/4 OD (32 mm OD) cable length = 13-13/16 (350 mm) COLD CLOSED 3-11/16 (94 mm) Deck Thickness Max. 1-3/16 (30 mm) Pop-up Drain cable connector 4

6 Installation Procedure 2 Install the Close 3 Install the Valve body Assembly 6 Pop-up Drain with Cable installation 1 Clean the cold/hot water supply pipes Before installation, dirt and debris in the cold/hot water supply pipes must be washed out. 6 Connect the pop-up drain with cable (only for faucet with pop-up drain ) Install the handles Connect the cold/hot water supply hoses Clean the cold/hot water supply pipes Important 5

7 2 Install the spout?wipe off the dirt around the installation hole.?measure the installation hole, select one from the two kinds of packings which meets the hole. Caution There are two kinds of packing in the package Select the one that meets the hole diameter. φ36 mm = 1-7/16in Hole over Hole under Winged packing Flat packing?if the packing is wrong, water may leak under the counter.?insert the packing through the connection pipe and spout fixing shaft to the groove in the bottom of the spout into the hole. Caution Be careful not to scratch or contaminate the O ring. Otherwise, water leakage may occur.?insert the spout mounting flange, flat washer, (big), lock washer (big) and spout mounting nut through the spout mounting shaft in the order, face the spout in its front side and attach the parts.?install the shank body with the flat washer (small), lock washer (small) and spout mounting nut. bottom Connection pipe mounting shaft spout mounting flange Flat washer (big) Lock washer (big) Mounting nut Flat washer (small) lock washer (small) spout mounting nut mounting shaft Packing Installation hole Section Mounting shaft shank body 6

8 3 Install the valve body assembly.?wipe away the dirt around the installation hole.?place the packing (white) through the water supply and connecting hoses, insert them into the hole in the counter. Caution The valve body assembly (C label) of cold water supply must be installed on the right side of the spout, the valve body assembly (H label) of hot water supply must be installed on the left side.?place the packing (black), slip washer, fastening nut through the water supply and connecting hoses, then fasten the valve body assembly. Top Escape hole Bottom Valve Body Assembly of cold water supply Packing (white) Counter Packing (black) Slip washer Cold water supply hose Fastening nut Connecting hose C label Cap Nut Caution When placing the connecting hose through the fastening nut, make the cap nut go through the escape hole. 7

9 4 Connect cold/hot water supply hoses Find the gasket in the connector and tighten the connector in the stop valve; use the tool to fasten them. Find the gaskets in the cap nuts of the cold/hot water supply hoses, screw on the connector, use the tool to fasten them. Find the gaskets in the cap nuts of the connecting hoses, screw on the shank body, use the tool to fasten them. Caution The connecting hoses should cross each other as shown in the right figure. Cautions for installing water supply hoses You have to bend the hose, but be careful not to break it. The minimum bending radius of the hose is 2-3/8 (60mm), if you bend it over the limit,it will break, which may cause early damage. During installation, do not bend the hose from the end surface of the main faucet body too far. Do not pull the hose violently. This may break the hose. Avoid unnecessary contact with similar hoses. If the external reinforced layer of the hose is damaged due to friction, the hose performance may deteriorate. Cold/hot water supply hose bending radius 2-3/8 (60 mm) Hot water supply hose Cap nut gasket connector gasket Stop valve connecting hose shank body Packing Cap nut Cold water supply hose GOOD BAD BAD BAD 8

10 5 Install the handles Place handle escutcheon then spacer on top of the valve unit. Secure with Hex Nut. Insert the bush and handle into the spindle part of the valve body assembly, use the screw to attach them. Insert the handle in the handle. Up Handle Cap Screw Handle Bush Hex Nut Spacer Caution Place the spacer with the small hole facing up. Adjust the seats on the cold/hot water sides to a flat surface, use tool to fasten the hex nut. Install the seats so that the HOT/ COLD marks are as shown in the right figure. To install the handle, orient the handle to make the knob stay in the position as shown in the right. handle escutcheon Spindle part of valve body asembly Flange HOT Knob Close Open COLD Knob Close Open 9

11 6 Pop-up Drain with Cable Installation (Only for faucet with Pop-up Drain) - Apply pipe tape to the flange threads. - Insert flange into the drain hole. - Assemble the gasket. flange nut and lock nut. - Apply pipe tape to the end threads of flange threads and install the tail piece to drain body -Make sure that cable faces toward the faucet. - Connect the cable base connector with cable handle connector. cable handle connector cable base connector clip clip Push button press the clip to be able to connect cable groove, to which connection is to be made drain body u-cup seal pop up drain body drain seal nut lock nut drain body locknut tailpiece flange drain gasket flange nut lavatory cable push button cable handle connector cable base connector tailpiece cable 8

12 How to Use How to adjust the temperature Open the main valve of the pipe, confirm water flow out of the spout. Open Close Hot side Drain Open Push Push button Cold side Turn the handles: confirm hot and cold water by turning each handle. To prevent scalding due to malfunction, the recommended hot water supply temperatureis 140 F (60 C) (for Faucet with Pop-up drain ) Open and close the Pop-up Drain (only for Faucet with Pop-up drain ) Push the push button. When the pop-up is closed, water can be kept in the washbasin. Push it again, the drain is opened and water will drain out. Push Push button Open 11 Drain Drain

13 Maintenance For performance and cleanliness, please maintain the product everyday. Maintain the water outlet Aerator Key Unscrew it Brush Aerator Using a Cloth to Clean Slightly dirty Use water and a damp cloth to wipe away the dirt completely. Seriously dirty Use cloth with dilute detergent to wipe away the dirt, then wash and dry it. Notes: Do not use the following materials Acidic cleaning agents, alkaline cleaning agents, or bleaches that are not TOTO scale cleaner. Solvents like thinner and benzene Cleaning agents like cleanser or grinding powder which contain coarse particles Nylon scrubbers and brushes 1. Unscrew the aerator by using the spout key provided to remove it. 2. Use a brush to clear dirt and debris from the aerator. 3. Install the aerator. Use the spout key provided to install it.?be careful not to lose the parts that have been removed. 12

14 Cleaning Drain 1.For maintenance press the pop button at first 2. Unscrew the pop up counterclockwise and take it out of the drain body 3. Cleaning utensil such as small brush can be used to clean the pop up Problem Open pop up Push small brush Push button Troubleshooting Check drain body pop up Flow is Is the aerator blocked with debris? Clean the aerator. too small When gas water heater device is used Set the gas hot water device with the product, is the switching properly with professional method set properly? help. Is the outlet hole frozen? Solution Water flows Do you lower down the lever handle to Lower the lever handle to without stop stop position? (Is it set to fully closed?) stop position. Is the stop valve fully opened? Use stop valve to adjust flow. Temperature can not be adjusted easily. Is the stop valve on the cold/ Hot sides fully opened? Does the water heater give adequate water? Apply hot water to the outlet. Adjust water flow with stop valve Check settingson water heater with professional help. pop up Unscrew Before contacting a repairman, check the following common problems and solutions. If the problem persists, contact your dealer or our tech support. Refer to Is the aerator blocked? Clean the aerator. Page 9 P.7 P.9 13

15 Replacement Parts No. Description 1 Handle Assembly 2 Handle Escutcheon Set (HOT) 3 Ceramic Cartridge (HOT) 4 Valve Body Assembly (HOT) 5 Connector Assembly 6 Mounting Hardware 7 Drain Assembly 8 Shank Assembly 9 Gasket, nut and O ring set 10 kit 11 Aerator 12 Handle Escutcheon Set (COLD) 13 Valve Body Assembly (COLD) 14 Ceramic Cartridge (COLD) 15 Connector Assembly 16 Mounting Hardware

16 WARRANTY LIFETIME LIMITED WARRANTY Warranty applies to selected residential faucets only. 1. TOTO warrants its faucets ( Product ) to be free from defects in materials and workmanship during normal residential use for as long as the original consumer end-user purchaser owns their home. This limited lifetime warranty is extended only to the original consumer end-user purchaser and only so long as the Product remains in use by the original consumer end-user purchaser in its original place of installation in the purchaser s residence. This warranty applies only to Product purchased and installed in North America. 2. TOTO obligations under this warranty are limited to repair or replacement, at TOTO s option, of Product or parts found to be defective in normal residential use, provided that such Product was properly installed and used in accordance with the owner s manual. TOTO reserves the right to make such inspections as may be necessary in order to determine the cause of the defect. 3. This warranty does not apply to the following items: Damage or loss sustained in a natural calamity such as fire, earthquake, flood, thunder, electrical storm, etc. Damage or loss resulting from any accident, unreasonable use, misuse, abuse, negligence, or improper care, cleaning or maintenance of the Product. Damage or loss resulting from sediments or foreign matter contained in a water system. Damage or loss resulting from improper installation or from installation of the Product in a harsh and/or hazardous environment, or improper removal, repair or modication of the Product. Damage or loss resulting from the use of an abrasive cleanser. 4. If the Product is used commercially, TOTO warrants the Product to be free from defects in materials and workmanship for one (1) year from the date the Product is installed, with all other terms of this warranty applicable except the duration of the warranty. 5. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE. 6. To obtain warranty repair service under this warranty, you must take the Product or deliver it prepaid to a TOTO service facility with proof of purchase (original sales receipt) together with a letter stating the problem, or contact a TOTO distributor or products service contractor, or write directly to TOTO U.S.A., INC., 1155 Southern road, Morrow, Georgia 30260, (888) If, because of the size of the Product or nature of the defect, the Product cannot be returned to TOTO, receipt by TOTO of written notice of the defect together with proof of purchase (original sales receipt) shall constitute delivery. In such case, TOTO may choose to repair the Product at the purchaser s location or pay to transport the Product to a service facility. THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY TOTO. REPAIR, REPLACEMENT OR OTHER APPROPRIATE ADJUSTMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE ORIGINAL PURCHASER. TOTO SHALL NOT BE RESPONSIBLE FOR LOSS OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE ORIGINAL PURCHASER, OR FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL, OR COSTS OF REPAIRS BY OTHERS, OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED. IN NO EVENT WILL TOTO S RESPONSIBILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR USE OR FOR A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU TOTO USA, Inc. á 1155 Southern Road, Morrow GA Phone (888) Fax (800) TOTO USA, INC. is a wholly owned subsidiary of TOTO Ltd. Printed in August, GU3026