Conditioning Hoppers. Installation and Electrical Wiring Guide

Size: px

Start display at page:

Download "Conditioning Hoppers. Installation and Electrical Wiring Guide"

Avice Hunter
5 years ago
Views:

1 Conditioning Hoppers Installation and Electrical Wiring Guide

2 PAGE -1 of 24 CONDITIONING HOPPER

3 We appreciate your business and hope you enjoy your Samuel Jackson Seed Cotton Conditioning Hopper This manual contains basic information on the installation of your Seed Cotton Conditioning Hopper. Additional information for the moist air pipe sizing, pipe routing, and fan requirements is usually supplied directly to the gin as each installation is unique. In the future when you require service, technical support, or parts please contact us by phone, fax, or the internet. Our engineers and service people are available to assist you in obtaining the best performance from your Samuel Jackson, Inc. products. Again, thanks for choosing a Samuel Jackson Seed Cotton Conditioning Hopper SAMUEL JACKSON, INCORPORATED MAIL: P.O. BOX LUBBOCK, TEXAS COURIER: 3900 UPLAND AVENUE LUBBOCK, TEXAS TELEPHONE OR TELEFAX engineering@samjackson.com Internet: Copyright 2004 SAMUEL JACKSON, INCORPORATED. All rights reserved. PAGE 0 of 24 CONDITIONING HOPPER

CLASSIC STYLE CONDITIONING HOPPER DIMENSIONS & PARTS Hoppers are custom made to fit into the space

The overall height, width and depth varies from installation to installation.

The following drawings are to be used for typical dimensions and views for Double Entry and Single

14100 Humid Air Valve (One for single entry, two for double entry) Valve in open position.

4 CLASSIC STYLE CONDITIONING HOPPER DIMENSIONS & PARTS Hoppers are custom made to fit into the space of the existing gin stand feeder hopper. The overall height, width and depth varies from installation to installation. A typical CLASSIC STYLE side double entry hopper is shown below. The following drawings are to be used for typical dimensions and views for Double Entry and Single Entry Hoppers. Consult factory for recommended layout for moist air piping Humid Air Valve (One for single entry, two for double entry) Valve in open position. Note roll pin indicator position. Roll pin valve position indicator Valve in closed position Inlet Transition 7 inch dia to 3 X 14, 12 inch overall length (One supplied for single entry, two for double entry) PAGE 1 of 24 CONDITIONING HOPPER

5 PAGE 2 of 24 CONDITIONING HOPPER

6 PAGE 3 of 24 CONDITIONING HOPPER

Consult factory for recommended layout of air piping. Hoppers are custom made to fit into the space of the existing gin stand feeder hopper.

7 END ENTRY STYLE DOUBLE AIR ENTRY CONDITIONING HOPPER The End Entry Style Double Entry Conditioning Hopper is shown below. Humid air enters the valves located on the ends of the Hopper requiring only one manifold pipe to connect multiple hoppers. Consult factory for recommended layout of air piping. Hoppers are custom made to fit into the space of the existing gin stand feeder hopper. The overall height, width and depth varies from installation to installation. A drawing showing typical dimensions and the dimensions required for construction is shown on next page Humid Air Valve with Transition PAGE 4 of 24 CONDITIONING HOPPER

8 PAGE 5 of 24 CONDITIONING HOPPER

PARTS FOR THE CONDITIONING HOPPERS A 13865 Plant Installation Package is included with the hopper order.

The 13850 Valve Relay Panel is used with all Samuel Jackson Humidaire Units except the HU-60-1260 oil-fired Humidaire Unit.

Refer to the section on electrical schematics for the wiring to match your model Humidaire Unit.

9 PARTS FOR THE CONDITIONING HOPPERS A Plant Installation Package is included with the hopper order. It includes a or Valve Relay Panel, a Relief Plug and a Air Filter, Regulator, Lubricator Assembly. The Valve Relay Panel is used with all Samuel Jackson Humidaire Units except the HU oil-fired Humidaire Unit. Use the panel for the 1260 model. Refer to the section on electrical schematics for the wiring to match your model Humidaire Unit Valve Relay Panel Valve Relay Panel (Note 5th relay required for use with the HU model Humidaire Unit) Air Filter, Regulator and Lubricator Assembly One Assembly supplies air to all hoppers in the system. Adjust regulator to about 80 psi pressure. PAGE 6 of 24 CONDITIONING HOPPER

INSTALLATION OF 13860 RELIEF PLUG ASSEMBLY The purpose of the Relief Plug is to allow a constant flow of air through the Humidaire Unit regardless of whether the hopper(s) are calling for air.

10 INSTALLATION OF RELIEF PLUG ASSEMBLY The purpose of the Relief Plug is to allow a constant flow of air through the Humidaire Unit regardless of whether the hopper(s) are calling for air. The weights are adjusted on the plug so that no air is relieved when all hoppers are calling for air and all air is relieved when no hoppers are calling for air. On the following page is a drawing showing the typical installation of the Relief Plug. Consult the factory for more information on its installation or to the sheet metal installation drawings supplied with the piping. Removable stack weights PAGE 7 of 24 CONDITIONING HOPPER

11 PAGE 8 of 24 CONDITIONING HOPPER

12 HOOK-UP OF HUMID AIR VALVE A decal is located near the air solenoid valve to help identify the valve ports. Compressed air of 80 psi (5.5 bars) is sufficient to operate the valve. This air should come from the Filter, Regulator and Lubricator Assembly. The solenoid valve coil is always volt, 50 or 60 HZ. Its power comes from the Humidaire Unit. Moist air butterfly valve is closed when coil is energized. EXHAUST EXH P B A AIR INLET 80 PSI (5.5 BAR) AIR VALVE & CYLINDER HOOKUP Air hook-up detail decal Air Cylinder Coil for valve 110V-50HZ, 120V-60HZ Solenoid Valve Humid Air Valve PAGE 9 of 24 CONDITIONING HOPPER

13 CONTROL LOGIC FOR HUMID AIR VALVES The butterfly valve in the Humid Air Valve should close the moist air flow off to the hopper when cotton is not flowing through the hopper. It is most common for the 240 VAC or 110 VAC signal to the Valve Relay Panel terminals 1,2, 3 and 4 (corresponding to each gin stand) to come from the gin stand breast in limit switch. Sometimes, the signal comes from the gin stand feeder feed works control. Terminal 9 is the common terminal for the signal input. A13850 or Relay Panel controls the action of the solenoid valves on the Humid Air Valves and the water pump run signal to the Humidaire Unit. If no hoppers are calling for cotton, the water pump run signal is off. As soon as one hopper calls for cotton, a water pump run signal is given. The solenoid valve coils on the Humid Air Valves are always VAC. Their power comes from the Humidaire Unit. SJI Part No Relays should be used for 120 VAC inputs. SJI Part No Relays should be used for 240 VAC inputs. PAGE 10 of 24 CONDITIONING HOPPER

14 FOLLOWING IS ELECTRICAL WIRING SCHEMATIC FOR VALVE RELAY PANEL FOR SINGLE AND DOUBLE ENTRY CONDITIONING HOPPERS USED WITH SAMUEL JACKSON HUMIDAIRE UNIT MODELS: HU GAS-FIRED HU-SOUTHWEST-1480 GAS-FIRED PAGE 11 of 24 CONDITIONING HOPPER

15 PAGE 12 of 24 CONDITIONING HOPPER

16 FOLLOWING ARE ELECTRICAL WIRING SCHEMATICS FOR VALVE RELAY PANEL FOR SINGLE AND DOUBLE ENTRY CONDITIONING HOPPERS USED WITH SAMUEL JACKSON HUMIDAIRE UNIT MODELS: HU GAS-FIRED HU OIL-FIRED PAGE 13 of 24 CONDITIONING HOPPER

17 PAGE 14 of 24 CONDITIONING HOPPER

18 PAGE 15 of 24 CONDITIONING HOPPER

19 FOLLOWING ARE ELECTRICAL WIRING SCHEMATICS FOR VALVE RELAY PANEL FOR SINGLE AND DOUBLE ENTRY CONDITIONING HOPPERS USED WITH SAMUEL JACKSON HUMIDAIRE UNIT MODELS: HU C GAS-FIRED HU OIL-FIRED HU GAS-FIRED PAGE 16 of 24 CONDITIONING HOPPER

20 PAGE 17 of 24 CONDITIONING HOPPER

21 PAGE 18 of 24 CONDITIONING HOPPER

22 FOLLOWING ARE ELECTRICAL WIRING SCHEMATICS FOR VALVE RELAY PANEL FOR SINGLE AND DOUBLE ENTRY CONDITIONING HOPPERS USED WITH SAMUEL JACKSON HUMIDAIRE UNIT MODELS: HU OIL-FIRED PAGE 19 of 24 CONDITIONING HOPPER

23 PAGE 20 of 24 CONDITIONING HOPPER

24 PAGE 21 of 24 CONDITIONING HOPPER

25 PAGE 22 of 24 CONDITIONING HOPPER

26 IMPORTANT! The following notice affects your warranty. Electrical Controls and Your Safety Your new Sam Jackson product may be equipped with electrical controls, or designed to interact with controls on a related Sam Jackson product. In the event that local, state, federal or other specified safety compliance is required, we will consider modifications to meet the particular requirements. Implementation of alternative safety devices may incur additional charges. No warranty of compliance with a particular standard is made in the absence of specific reference to it in our quotation. If you modify, or permit others to modify, these controls without specific written permission from Sam Jackson, Inc. the warranty on your product will be void and there is a possibility of serious damage to machinery, damage to product, serious injury to personnel, or death. The modifier of the controls assumes all liability for these consequences. Samuel Jackson, Incorporated 3900 Upland Avenue Lubbock, Texas PAGE 23 of 24 CONDITIONING HOPPER

27 This page intentionally blank

HG Million Btu/Hr Gas-Fired Heater

HG Million Btu/Hr Gas-Fired Heater HG-1-1142 1-Million Btu/Hr Gas-Fired Heater PAGE -2 of 30 HG-1-1142 GAS-FIRED HEATER Table of Contents Warnings... 1-2 Specifications... 3 Preliminary Checks Prior to Initial Operation... 4 Adjusting the