EDGE PATIO HEATER. User Manual. English

Transcription

1 EDGE PATIO HEATER User Manual English

2 CONTENTS SAFETY FIRST Safety... 3 Introduction... 4 Moving & Positioning... 5 Operation Troubleshooting Specifications & Cleaning WARRANTY --- All our Patio Heaters come with a 2-year full manufacturer s collect and return warranty (from the date of purchase). Proof of purchase will be required to qualify for the warranty. The warranty can t be transferred to a second owner. As part of our warranty agreement we take liability for collecting faulty items, as well as liability for any replacements and repairs. We ll also be liable for the cost of returning the items to you. Please note that we re not liable for any costs that are incurred by third party companies, including: builders or electricians. If the product has been tampered with or modified it will void the warranty. WARNING - When using electrical appliances, basic safety precautions should always be followed. Failure to comply with these instructions may cause a fire, electrical shock or other injury to persons or property. 1. Children of less than 3 years should be kept away unless continuously supervised. 2. Children between 3 and 8 years old should only be allowed to switch the appliance on/off, provided that it has been correctly installed in its intended operating position and they have been given supervision or instruction concerning the safe use of the appliance and understand the hazards involved. They should not plug in, regulate, perform maintenance or clean the appliance. 3. DO NOT position the heater on soft surfaces or where openings may become blocked. Ensure the base is fitted and fully assembled, and the unit is upright on a flat stable surface before operating. This heater is designed for use on patios and in beer gardens & smoking areas. The unit has been IP55 Weatherproof approved; however, to prolong the life of the heater it is strongly recommended that the heater is stored in a dry place during heavy rain and when not in use cover the appliance with the cover provided. 4. DO NOT hide the power cord in long grass or leave close to an operating lawnmower. Arrange the cord away from areas where it may be tripped over. 5. DO NOT insert or allow objects to touch the heating element and never place anything on the heater safety guard (e.g. towels), as this may damage the heater and could cause an electrical shock or fire. Never use your heater to dry washing. If the heating element has stopped glowing it may still be live, please check that the heat setting indicates the heater is off. 6. Always disconnect your appliance from the mains before any cleaning. 7. DO NOT use the heater in areas where petrol, paint, or other flammable substances are stored. Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool. 8. Always unplug the heater when not in use. To disconnect from the power supply, grip the plug and pull from the power socket. Never pull by the cord. 9. DO NOT direct the heater towards curtains, furniture or other flammable objects and ensure that they are at least 0.8 metre from the front and 0.5 metre from the top and sides. 10. Extreme care should be taken when the heater is used near children and pets. 11. Do not use the heater with a programmer, timer or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly. 12. In order to avoid overheating, do not cover the heater. The electrical cord must be fully unwound before use. Heater should not be positioned directly under a socket outlet. 13. The front grille is intended to prevent direct access to the heating elements and must be in place when the heater is on. 14. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if, they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and maintenance should not be attempted by children without supervision. 15. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 16. CAUTION Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present. 17. WARNING: This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided. 2 3

3 INTRODUCTION INSTALLATION Our sleek Edge heater is designed to be mounted vertically direct onto any wall surface to save space and blend into your space. Make sure your Edge is mounted at least 10cm from the floor, 80cm away from other objects in front and has at least 50cm cleaance to the left and right sides. Popular for both patio and covered/indoor spaces, the Edge is rated at 2000W and its carbon fibre infrared technology will comfortably heat up to 14m 2. Simple hook and slot mounting makes installation easy, while safety is always paramount. We use an innovative safe-touch housing where temperature cannot exceed 60-degrees, as well as having a flocked-grill for maximum protection. The high waterproof rating of IP55 means it s built to withstand the elements, whether wind, snow or rain, and hence suitable for outdoors installation. For convenience the Edge comes with a remote control so that the heater can be controlled from a distance, and they also have a handy built-in timer and an eco-mode that turns off the heater if the sensor cannot detect people within the vicinity. E D Use the Sleeve Anchors (4 x E) to nail the Slot Bracket (D) on the wall vertically as shown. Recommended height: To mount your heater 25-40cm high from the floor, height of the Slot Bracket s (D) upper edge on the wall should be cm. Install the mains socket (bottom edge) 40-55cm vertically higher than the Slot Bracket s upper edge. If the wall mains socket is there already, to make a flush mounting, you need to vertically fix the Slot Bracket 8cm (minimum) below the socket s bottom edge. Make sure the Slot Bracket is at least 70cm high from the floor. Features Innovative electric heating technology produces 2000W of infrared heat Ultra low glare carbon fibre heating element built to withstand over 8000 hours of use Heat distribution area up to 14m 2 Waterproof rating of IP55 making it perfect for outdoor use, whatever the weather Comes complete with vertical wall-mount bracket for flexible, easy installation Control the device using the control panel or remote control Advanced control functions include eco-mode (detects movement and shuts down when no one in vicinity) and off-timer (shuts down at specified time of 1, 2, 3 or 4 hours) Patented snap-in heating tube structure makes replacing tubes easy Safe-touch housing material temperature cannot exceed 60 Robust anodised extruded aluminium construction with brushed metal finish WARNING 40cm-55cm Recommended for easy cable storing E A D If you want to fix your heater on the wall to avoid theft, before you mount the heater, fasten the Fix Bracket (F) to the heater by its Fix Screw (F) - the Screw and Washer may be assembled on the Heater s body already). After mounting the heater, nail the Bracket on the wall by the Sleeve Anchor (1 x E) - see left picture. Hold the Heater (A) vertically and insert the Hook on the back into the slot of the Bracket (D). To get the flush mounting, you need to plug in before mounting the heater. Twist the cable into the heater s back and plug in (make sure the Power Switch is at OFF position when you do so). In this case, your mains socket s bottom edge shall be vertically 10-60cm higher than the Slot Bracket s upper edge. This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided. 70cm or higher F The gap between the heater and the wall is bigger than the cable s diameter, so plugging in a socket away from the heater is possible. 10cm minimum 4 5

4 OPERATION Please follow the below instructions to operate your heater safely. To avoid tampering - this heater can only be controlled via its Remote Control unit. Remote Control will work up to 4m from the heater (line of sight). Remote Control Operation Economy Button Activates the PIR Sensor - heater will automatically shut off if it detects no movement in the area for 4 minutes Heat Button Turns the heating elements On/Off Timer Button Set the Timer function - 1/2/3/4hrs or None Indicator Panel Power indicates power is present Economy Indicates Economy function has been activated via the remote Timer 4 lights indicating if Timer is set - 1/2/3/4hrs or None Heat Indicates heating elements are active PIR Economy Function ECONOMY HEAT TIMER ECONOMY HEAT TIMER The PIR economy function enables the heater to automatically shut down its heating elements when not in use. The PIR sensor constantly monitors people s movements up to a distance of 4 metres. If does not detect any movement within 4 minutes, it will switch the heating off to be safe and economic. To re-activate the heating elements the remote control must be used. Replace CR2032 Battery Here 6 7

5 TROUBLESHOOTING Heater won t operate (indicated by the absence of the BLUE POWER standby light being visible in the unit indicating panel display) Power Switch OFF No Power to unit Safety Thermal Fuse in Operation. Turn Power Switch On Check the mains or electrical socket to restore power. Unplug and switch unit OFF. Wait 30 minutes for unit to auto-reset then switch on. Repeat if necessary. HEAT indicator flashing red Safety Warning Indicator If the HEAT light starts to flash or flicker intermittently, this indicates a problem within the internal control systems of the unit. Please switch off the unit immediately, leave for 30 minutes and switch on again. If this continues to occur please call customer service. Power Cord Damaged Inspect power cable for cuts, breaks and kinks. Replacement power cords and fitting instructions can be obtained by calling customer service. Flashing Not visible Economy function failure (GREEN ECONOMY light on the Indicating panel not visible when ECONOMY button pressed from the remote) Heating function is not ON PIR / PCB malfunction IR function is effective with LIVE heating only. Please turn on heating mode. Please call customer service. Heat tubes not working (indicated by the presence of the BLUE POWER standby light, the RED HEAT light being visible in the unit indicating panel display but no heat from tubes) Visible Tube Failure / Safety Thermal Fuse in operation. Blown Carbon Fibre Tubes Try the following procedures to ensure it is in fact the tube that is faulty. 1) Push the remote HEAT button again just to check the tube doesn t heat up. 2) If still not heating check if the RED HEAT light on the Indicating Panel is on? If the light is ON then the tube has blown. Replace the Tube. If not then wait 30 minutes for unit to auto-reset and switch on after. Repeat if necessary. If this continues to occur please call customer service. Blown tubes are usually visible. Check for black or white discolouration at either end of the tubes. If visible, call customer service. Not visible when ECONOMY button pressed on remote Remote control inoperative Battery dead Make sure the red power indicator is visible otherwise you need to replace battery (Type CR2032/CR2025). See page

6 SPECIFICATIONS NOTES Heating Power: 2000W Product Dimensions: 195mm (W) x 1270mm (H) x 147mm (D) Product Weight: 7.2kg Heating Element: Carbon Fibre Tube Element Life: More than 8000 Hours Heat Distribution Area: Up to 14m 2 Heating Angle: 130 Heating Distance: 3.5m Power Supply: v, 50/60Hz Power Cable Length: 100cm Power Connection: British Standard (BS) Plug Control Method: Control Panel, Remote Control Control Function: Off-Timer, Eco-Mode Casing: Anodised Extruded Aluminium Construction with Brushed Metal Finish Installation: Vertical Wall Mounted Safety Device: Overheat Protection Waterproof Rating: IP55 Insulation: Class 1 Certifications: CE, EMC, GS, IP55, RoHS Warranty: 2 Years Cleaning & maintenance Before cleaning or changing heating tubes, turn the heater off, unplug from the power supply and wait for the unit to cool down. To clean the heater use a soft cloth to wipe off any dust. If the heater is very dirty, use a damp cloth and wipe dry. Do not use any cleaning detergents, sprays or other chemicals, as they will damage the unit. When the heater is not in use for a long period, clean and place in a cover and store in a dry place. If the Aluminium reflector is very dirty use a damp cloth and wipe dry. Do not use any cleaning detergents, sprays or other chemicals, as they will damage the unit. A dirty reflector reduces heater output. The product is IP55 weatherproof certified. It is designed to withstand tough rain conditions. We recommend that you should cover the product when not in use for long periods of time with a storage cover - please contact customer service for details

7 Optima Heaters, Unit 11, Aerodrome Close, Loughborough, LE11 5RJ