Light Control guide for Soundlight Comfort Ceiling OccuSwitch DALI Control Guide

Transcription

1 Light Control guide for Soundlight Comfort Ceiling OccuSwitch DALI Control Guide

2 Content: Ensure right physical install of all hardware / use remote control to commission the OccuSwitch Definitions of ceiling plan Calibrate light level Setting a mode Assign DALI function to every LED tile cluster Optional functions Set background level (optional, default 20%) Set power up state Set IR group to match system with remote control Movement test Back to basic setting Switch lights on/off!!! Attention Always keep pointed to OccuSwitch DALI sensor Attention Lights will allways flash once after every successful change Attention Luxmeter needed for calibration of the installation

3 1 Max 1 m Ensure right physical install of all hardware. See Installation Guide IG324 Definitions of ceiling plan Follow the lighting design for specified room type made by the lighting designer Examples: Group 2 x = Led Tile in assigned cluster o = Led Tile in assigned cluster LED Tile cluster = LED Tiles connected to same Control box Group = one or several LED Tile cluster having the same Dali assignment. E.g window or LED Tiles in cluster behaves equally

4 Calibrate the light level Luxmeter 3 1 Push up or down to set the required light level 2 Press save when the lux meter is showing the required lux level (eg 500 lux)! Attention Always calibrate the installation Calibration must be done at night and office must be furnished Setting the modes 4 1 Press mode 2 Select (Press 01; ) 3 Press send (4) (check mode) m/s = master / slave t/w = task lighting / workspace lighting Mode Application 01 cell office m/s 02 open plan m/s 03 classroom m/s 04 open plan t/w 05 cell office t/w toilets 08 meeting room 09 open plan t/w 10 custom More detailed information about Mode overview (default settings), see last page. When checking modes, light are fl ashing! Flashing number indicates the setup mode of your choice 01 to 10

5

6 DALI function assignment 5 1 Press DALI 2 Wait for a cluster of LED Tiles to flash If no flash occurs press 1 until a cluster of LED Tiles start flashing 3 Select function for cluster of LED Tiles: 1=window 2= 3=additional presence 4=additional absence 4 Repeat for next flashing cluster of LED Tiles (5 Press DALI to abort) When finished all luminaires flash once! This setting splits each clusters (Control Boxes) depending on the selected function. Later on, any of the four groups you can set up differently with the remote control, and its behavior is dependent according to the selected mode. Function 1 - (window) automatically adjusts lighting levels depending on the outdoor light conditions and presence detection. Function 2 - () automatically adjusts lighting levels depending on the outdoor light conditions and presence detection of the room, basic light level is 20% higher than in function 1- window Function 3 - (presence) light are on in presence mode and are automatically switched off if absence of people. Function 4 - (absence) Light are off in absence mode and are automatically switched on if absence of people. Optional functions 6-11

7 Change Background level 6 1 Press background 2 Select min -- 70% 3 Press send m/s = master / slave t/w = task lighting / workspace lighting Mode Application Background Factory default 01 cell m/s 02 open plan m/s 20% (all lights)* 03 classroom m/s 04 open plan t/w Preset 1** 05 cell t/w 06 20% (all lights)* 07 toilets Preset 1** 08 meeting room 09 open plan t/w 20% (all lights)* 10 custom Preset 1** * = default ** = workspace Change power-up state 7 1 Press power up 2 Select on/off status 3 Press send Mode Power-up (factory default) 01 off 02 off 03 off 04 off 05 off 06 on 07 on 08 off 09 on 10 on

8 IR group addressing 1 Press IR group 8 2 Select group A-G 3 Press send Set IR group remote control The individual groups can be assigned to a specific remote control to avoid interference eg. In a larger space with more controlers. Adressing is done by setting the pins on the back side of Tobetouche, directly on the remote control following the enclosed instructions. Movement test 9 1 Press test OccuSwitch DALI will now operate 10x faster than normal. MD timer = 30 sec fixed 2 Press test to stop (automatic stop after 60s no movement)

9 Back to basic setting (mode 1) 1 Press reset 10 2 Press send Switch lights on or off 11 1 Press on 2 Press off

10 Mode Application Occupancy Cell office (default) Open plan office 03 Class room Auto ON/OFF Auto ON/OFF ManualON/ autooff Smart timer (minutes) Background period (minutes) Daylight override 10 0 N.a. 04 Open plan* Disabled 10 0 N.a. 05 Cell office* Disabled 10 0 N.a. 06 Corridor Auto ON/OFF Auto 07 Toilets ON/OFF 08 Meeting room ManualON/ autooff 09 Open plan office** Auto ON/OFF Mode overview (default settings) (portal ) 10 0 Disabled 10 Infinite Daylight dependent regulation Daylight dependent switching Disabled Disabled Disabled 10 custom N.a. N.a. N.a. N.a. N.a. N.a. N.a. Parallel link period (Advanced ) N.a. N.a. Background lighting * Equals mode 1 and 2, but without MD active. Do not use these modes for normal applications. ** This mode works differently in the advanced (LRM2080) version. Here the lights will switch off (the basic never switches off) when none of the advanced OccuSwitch DALI units in the parallel network detect movement. If one, or more, do detect movement all other units will go to background level.