Premium Version Tri-level Dimming Control

Transcription

1 0 Premium Version Tri-level Dimming Control Model: HC9VRC with HRC-0 Infrared remote receiver Detection area Buzzer Sensor antenna indication Daylight threshold Stand-by period Installation hole (.mm) Daylight sensor + -0V EXT. EXT. Model: HC9VRC L N L Push Mechanical structure (mm). 8 Detection Pattern Daylight Monitoring TM Condominium control 8 hours manual on Ambient daylight threshold s~0min ~0Lux With multiple functions, HC9VRC is newly developed to meet various requirements for project contractors and OEMs in real applications. Compact size, easy operation with remote control, and deep energy saving! Functions and Options Tri-level Dimming Control (Corridor Function) Same as Tridonic excel control gear, Hytronik builds this function inside the motion sensor to achieve tri-level dimming control, for some areas require a light change notice before switch-off. It offers levels of light: 00%-->dimmed light-->off; and periods of selectable waiting time: motion hold-time and stand-by period; Selectable daylight threashold and freedom of detection area. Master/ Group Control By connecting the EXT terminals in parallel (maximum 0pcs, see wiring diagram), no matter which sensor detects motion, all HC9VRC in the group will turn on the lights when surrounding natural light is below daylight threshold. The sensor antenna is shared and the detection area could be widely enlarged in this way. Other settings such as hold-time, stand-by period, stand-by dimming level and daylight threshold on each individual unit stay the same. Note: if the surrounding natural light of the sensor which detects movement is sufficient, all lights in the group will not be triggered on.

2 With sufficient natural light, the lights does not switch on when presence detected. With insufficient natural light, the person comes from any direction, the whole group of lights switch on. After hold-time, the whole group of lights dim to stand-by level or turns off completely if surrounding natural light is above the daylight threshold. After the stand-by period, the whole group of lights switches off automatically. Multiple sensors control the same group of ballast /driver Wiring Diagram -0V EXT. -0V EXT. -0V Driver -0V Driver Note: this -0V output is isolated, SELV output. Do not connect the -0V terminals on driver X to Driver Y. 8H Manual on Mode for Lamp Rapidly turn off/on the power supply three times within seconds, the light will be 00% on for 8 hours, and then goes to sensor mode automatically after 8 hours. Useful when sensor function is not needed in special occasion. Note: this 8H manual on mode can be cancelled by turning off/on the power supply one time within second. Ambient Daylight Threshold Switch the power supply to the sensor two times within seconds, the sensor can set the ambient lux level as the new threshold. Both the settings on DIP switch and the ambient lux threshold learned can overwrite each other. This feature enables the daylight sensor to be commissioned to the environment in which it is installed. The latest action controls. (More details of the operation procedure please refer to user manual).

3 Daylight Monitoring Function Hytronik specially design this function in software for deep energy-saving purpose. A built-in daylight sensor is designed to provide smart photocell function. This function can only be activited when stand-by period is set to +. Settings on this demonstration: : 0min Daylight threshold: 0lux : 0% Stand-by period: + :00 :0 :0 goes in cycle during the night... 00% on when movement detected, and dims to0% in long absence. The light switches on at 00% when there is movement detected. Light dims to stand-by level after the hold-time (no motion). Light keeps in dimming level during the night. 08:0 7:0 Insufficient light and with presence, 00% on Insufficient light Motion Dimming level No motion, after hold-time Every 0min At dawn, light turns off completely when natural light reaches above daylight threshold. Light turns on 0% automatically when natural light is insufficient. Off Sufficient light Check Insufficient light 6 Manual Override This sensor reserves the access of manual override function for end-user to switch on/off, or adjust the brightness by push-switch, which makes the product more user-friendly and offers more options to fit for some extra-ordinary demands: * Short push (<s): on/off function; On off: the light turns off immediately and can not be lighten for a certain time (equals to hold-time preset) even movement is detected. After this period, the sensor goes to sensor mode. Off on: the light turns on and goes to sensor mode, no matter if ambient Lux level exceeds the daylight threshold or not. * Long push (>s): dim up/down the hold-time brightness between 0% and 00%. Both the settings on DIP switch and manual override can overwrite each other, the latest action controls. Note: if end-user do not want this manual override function, just leave the push terminal alone and don t connect it to any wire. Multiple sensors control the same group of ballast /driver Wiring Diagram -0V EXT. -0V EXT. -0V Driver -0V Driver Note: this -0V output is isolated, SELV output. Do not connect the -0V terminals on driver X to Driver Y.

4 0 7 Absence Detection Function It is easy to forget to switch off the light, in office, corridor, even at home. And in many other cases, people do not want to have a sensor to automatically switch on the light, for example, when people just quickly pass-by, there is no need to have the light on. The solution is to apply this absence detector : motion sensor is employed, but only activated on the maunal press of the push switch, light keeps on in the presence, and dimmed down in the absence, and eventually switch off in the long absence. It is a good combination of sensor automation and maunal override control, to have the maximum energy saving, and at the same time, to keep efficient and comfortable lighting. Light does not switch on when presence detected. Short push to activate the sensor and switch on the light With the manual short press on the push-switch, the sensor is activated and switches on the light. Light keeps on during the presence. People left, light dims to 0%/0%/ 0%/0% (optional) stand-by level after the hold-time. Light switches off automatically after the stand-by period elapsed. Note: end-user can choose either function 6 or function 7 for application. Default function is manual override. Detection Pattern 0 9 Ceiling mounted height (m) 0% 0% 0% 7% Wall mounting height (m) 0% 0% 0% 7% Ceiling mounted detection pattern (m) Wall mounted detection pattern (m)

5 Settings (Remote Control HRC-0) ON/ OFF Permanent ON/OFF function Press the ON/OFF button, the light goes to permanent on or permanent off mode, sensor is disabled. * Press Auto Mode, RESET or Scene mode buttons to quit from this mode. ON/ OFF Auto Mode Reset Auto Mode Sensor mode Press Auto Mode button, the sensor starts to work and all settings remain the same as the latest status before the light was switched on/off. SC SC Scene mode SC SC Detection range 00% + Dim - 80% Reset function 00% 0% 0% Daylight Sensor Press RESET button, all settings go back to the value of DIP switch settings. 0% 0% 0% Lux Dim +/- Test s 0s min 0Lux min Long press Dim + or Dim to adjust the light brightness during hold-time. + means dimming up, means dimming down. min 0min 0min 0Lux Test mode The button Test s is for testing purpose only. The sensor goes to test mode (hold-time is s) automatically after commissoning, meanwhile the stand-by period and daylight sensor are disabled. * This mode can be ended by pressing reset, or any button of scene mode and hold time. The sensor setting is changed accordingly. 0s 0s min 0min Stand-by period 0min Lux Disable M/A HRC-0 Note: the buzzer beeps one time when RC receives signal successfully. 00% 80% output By pressing these two buttons, the output shifts between 80% (at initial 0,000 hours) and 00%, for energy saving purpose. Ambient daylight threshold Press this button, the latest surrounding lux value overwrites previous lux value learned, and is set as the daylight threshold. This feature enables the fixture to function well in any real application circumstance. Lux Disable Lux disable Press this button, the built-in daylight sensor stops working, and all motion detected could turn on the lighting fixture, no matter how bright the natural light is. M/A Manual override / absence detection By pressing this button, the sensor goes to manual override or absence detection function. Note: The buzzer beeps twice if it s manual override function, and beeps once if shifts to absence detection function. Scene mode There are scene modes fixed program built-in the remote control to choose for different applications: Scene options Detection range Stand-by period Daylight sensor SC 00% min 0min 0% Lux SC 00% min 0min 0% Lux SC 00% 0min 0min 0% 0Lux SC 00% 0min 0% 0Lux Note: End-user can adjust the settings by pressing buttons of detection range/hold-time/stand-by period/stand-by dimming level/daylight sensor. The lastest setting stays in validity.

6 Detection range Press the buttons of detection range to set detection range at 0% /0% /00%. Daylight sensor Press the buttons of daylight sensor to set daylight threshold at Lux / 0Lux / 0Lux. Press the buttons of hold-time to set hold-time at 0s / min / min / 0min / 0min. Press the buttons of stand-by dimming level to set the stand-by dimming level at 0% / 0% / 0%. Stand-by period (corridor function) Press the buttons of stand-by period to set stand-by period at 0s / 0s / min / 0min / 0min / +. Note: 0s means on/off control; + means bi-level dimming control, light never switches off when daylight sensor is disabled. Settings Detection area Detection area can be reduced by selecting the combination on the DIP switches to fit precisely for each specific application. 00% 0% I 00% II 0% means the time period to keep the lamp on 00%, after all motion has ceased (detection area vacated). s min 0min 0min I s II min III 0min IV 0min Daylight sensor The daylight threshold can be set on DIP switches, to fit for particular application. Disable 0Lux 0Lux Lux I Disable II 0Lux III 0Lux IV Lux Stand-by period(corridor function) This is the time period you would like to keep at the low light output level before it is completely switched off in the long absence of people. Note: 0s means on/off control; + means bi-level dimming control, fixture never switches off when daylight sensor is disabled s 0s min min 0min 0min h + I 0s II 0s III min IV min V 0min VI 0min VII h VIII + This is the dimmed low light output level you would like to have after the hold-time in the absence of people. 0% 0% I 0% II 0% Technical Data Operating voltage Switched power (capacitive load) Stand-by power Detection area Stand-by period Daylight threshold Sensor principle Microwave frequency Microwave power Detection range Detection angle Mounting height Operating temperature IP rating Certificate 0-77VAC 00W@0VAC; 000W@77VAC <W 0% /00% (00% /0% /0% on RC) s /min /0min /0min (TEST s /0s /min /min /0min /0min on RC) 0s /0s /min /min /0min /0min /h/+ 0% /0% (0% /0% /0% on RC) (0s /0s / min / 0min/ 0min /+ on RC) ~0Lux, disable (Lux /0Lux /0Lux /Lux disable on RC) High Frequency (microwave).8ghz+/-7mhz <0.mW Max. ( O xh): 8m x m 0 o ~0 o Max. m -0 o C ~ +60 o C IP0 IP6 (mounted in Hytronik special box) Semko, CB, EMC, CE, R&TTE, SAA