American National Standards

Transcription

1 PUBLISHED WEEKLY BY THE AMERICAN NATIONAL STANDARDS INSTITUTE 25 West 43rd Street, NY, NY VOL. 47, #31 July 29, 2016 Contents American National Standards Call for Comment on Standards Proposals... 2 Call for Members (ANS Consensus Bodies)... 9 Final Actions Project Initiation Notification System (PINS) ANS Maintained Under Continuous Maintenance ANSI-Accredited Standards Developers Contact Information International Standards ISO and IEC Draft Standards ISO and IEC Newly Published Standards Proposed Foreign Government Regulations Information Concerning American National Standards Call for comment on proposals listed This section solicits public comments on proposed draft new American National Standards, including the national adoption of ISO and IEC standards as American National Standards, and on proposals to revise, reaffirm or withdraw approval of existing American National Standards. A draft standard is listed in this section under the ANSI-accredited standards developer (ASD) that sponsors it and from whom a copy may be obtained. Comments in connection with a draft American National Standard must be submitted in writing to the ASD no later than the last day of the comment period specified herein. Such comments shall be specific to the section(s) of the standard under review and include sufficient detail so as to enable the reader to understand the commenter's position, concerns and suggested alternative language, if appropriate. Please note that the ANSI Executive Standards Council (ExSC) has determined that an ASD has the right to require that interested parties submit public review comments electronically, in accordance with the developer s procedures. Ordering Instructions for "Call-for-Comment" Listings 1. Order from the organization indicated for the specific proposal. 2. Use the full identification in your order, including the BSR prefix; for example, Electric Fuses BSR/SAE J Include remittance with all orders. 4. BSR proposals will not be available after the deadline of call for comment. Comments should be addressed to the organization indicated, with a copy to the Board of Standards Review, American National Standards Institute, 25 West 43rd Street, New York, NY ; psa@ansi.org * Standard for consumer products 2016 by American National Standards Institute, Inc. ISSN ANSI members may reproduce for internal distribution. Journals may excerpt items in their fields

2 Comment Deadline: September 4, 2016 NSF (NSF International) BSR/NSF x (i78r1), Plastics piping system components and related materials (revision of ANSI/NSF ) The physical, performance, and health effects requirements in this Standard apply to thermoplastic and thermoset plastic piping system components including, but not limited to, pipes, fittings, valves, joining materials, gaskets, and appurtenances. Click here to view these changes in full Send comments (with copy to to: Lauren Panoff, (734) , NSF (NSF International) BSR/NSF x (i91r2), Equipment for Swimming Pools, Spas, Hot Tubs and Other Recreational Water Facilities (revision of ANSI/NSF ) This Standard covers materials, components, products, equipment and systems, related to public and residential recreational water facility operation. Click here to view these changes in full Send comments (with copy to to: Lauren Panoff, (734) , UL (Underwriters Laboratories, Inc.) BSR/UL X, Standard for Safety for Electrostatic Air Cleaners (Proposal dated ) (revision of ANSI/UL ) This proposal includes: (1) Addition of requirements for household appliances incorporating button or coin cell batteries, and (2) Addition of grounding symbol. Click here to view these changes in full Send comments (with copy to to: Ross Wilson, (919) , UL (Underwriters Laboratories, Inc.) BSR/UL X, Standard for Safety for Halocarbon Clean Agent Fire Extinguishers (revision of ANSI/UL ) It is recognized that there is not one-size-fits-all quality values for halon replacements, therefore ASTM publishes a quality specification for each extinguishing agent. Revise UL standard to reference applicable ASTM quality specification or equivalent. Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Mark Ramlochan, (613) , Mark.Ramlochan@ul.com Comment Deadline: September 12, 2016 ADA (American Dental Association) New National Adoption BSR/ADA Specification No x, Orthodontic Wires (identical national adoption of ISO 15841:2014 and revision of ANSI/ADA Specification No (R2010)) This standard specifies requirements and test methods for wires to be used in fixed and removable orthodontic appliances. It includes preformed orthodontic archwires but excludes springs and other preformed components. This standard gives detailed requirements concerning the presentation of the physical and mechanical properties of orthodontic wires, the test methods by which they can be determined, and packaging and labeling information. Single copy price: $88.00 Obtain an electronic copy from: standards@ada.org Order from: Kathy Medic, (312) , medick@ada.org ANS (American Nuclear Society) Reaffirmation BSR/ANS (R201x), Probabilistic Seismic Hazard Analysis (reaffirmation of ANSI/ANS ) This standard provides criteria and guidance for performing a probabilistic seismic hazard analysis for the design and construction of nuclear facilities. Single copy price: $ Obtain an electronic copy from: scook@ans.org Order from: Sue Cook, (708) , orders@ans.org Send comments (with copy to psa@ansi.org) to: Patricia Schroeder, ANS; pschroeder@ans.org ASSE (ASC A10) (American Society of Safety Engineers) New Standard Standards Action - July 29, Page 2 of 38 Pages BSR/ASSE A X, Debris Net Systems Used during Construction and Demolition Operations (new standard) This standard establishes safety requirements for the design, selection, installation, and use of debris net systems during construction, demolition operations and for the temporary containment of debris from deteriorating structures. (NOTE: This standard is a revision of the ANSI A Standard. This standard was administratively withdrawn by ANSI during October of 2006, but was relaunched per consensus of the A10 ASC.) Single copy price: $50.00 Obtain an electronic copy from: TFisher@ASSE.Org Order from: Tim Fisher, (847) , TFisher@ASSE.Org

3 Standards Action - July 29, Page 3 of 38 Pages ASSE (ASC A10) (American Society of Safety Engineers) Reaffirmation BSR/ASSE A (R201x), Safety & Health Program Requirements for Demolition Operations (reaffirmation of ANSI/ASSE A ) This standard applies to the demolition of buildings and other structures. This standard is intended to be complete in itself, except that any device, equipment, and activity incidental to demolition operations shall be conducted, installed, inspected, maintained, and operated in accordance with the requirements in American National Standards for Safety in Construction and Demolition Operations A10 Series, other American National Standards listed in Section 2 and other appropriate standards. (NOTE: The original plan was to revise the standard, but the committee consensus is now to reaffirm and then launch the revision process again.) Single copy price: $50.00 Obtain an electronic copy from: TFisher@ASSE.Org Order from: Tim Fisher, (847) , TFisher@ASSE.Org ASSE (ASC A10) (American Society of Safety Engineers) Reaffirmation BSR/ASSE A (R201x), Safety Requirements for Excavation (reaffirmation of ANSI/ASSE A (R2010)) This standard applies to all open excavations made in the earth's surface that require worker and/or property protection. See Section 3, Requirements for Protection Systems. Excavations are defined to include trenches. Single copy price: $50.00 Obtain an electronic copy from: TFisher@ASSE.Org Order from: Tim Fisher, (847) , TFisher@ASSE.Org ASSE (ASC A10) (American Society of Safety Engineers) Reaffirmation BSR/ASSE A (R201x), Safe Operating Practices for Tile, Terrazzo, and Marble Work (reaffirmation of ANSI/ASSE A (R2011)) This standard establishes safety requirements for construction operations and equipment used in the handling and installation of ceramic tile, terrazzo, and marble. The types of construction are not listed. The standard is intended to apply to buildings of all kinds and to heavy construction, such as work in tunnels. Single copy price: $50.00 Obtain an electronic copy from: TFisher@ASSE.Org Order from: Tim Fisher, (847) , TFisher@ASSE.Org ASSE (ASC A10) (American Society of Safety Engineers) Reaffirmation BSR/ASSE A (R201x), Safety and Health Program Requirements for Multi-Employer Program - Standard for Construction and Demolition Operations (reaffirmation of ANSI/ASSE A ) This standard sets forth the minimum elements and activities of a program that defines the duties and responsibilities of construction employers working on a construction project where multiple employers are or will be engaged in the common undertaking to complete a construction project. Single copy price: $50.00 Obtain an electronic copy from: TFisher@ASSE.Org Order from: Tim Fisher, (847) , TFisher@ASSE.Org ASSE (ASC A10) (American Society of Safety Engineers) Reaffirmation BSR/ASSE A (R201x), Safety Requirements for Tunnels, Shafts, and Caissons - Standard for Construction and Demolition Operations (reaffirmation of ANSI/ASSE A ) This standard establishes safety requirements pertaining to the construction of tunnels, shafts, and caissons. The requirements set forth in this standard cover environmental control; related facilities; fire prevention; hoisting; haulage; and electrical, drilling and blasting, and compressed air work. This standard is not intended for application to mining or quarrying operations. Single copy price: $50.00 Obtain an electronic copy from: TFisher@ASSE.Org Order from: Tim Fisher, (847) , TFisher@ASSE.Org ASSE (ASC Z359) (American Society of Safety Engineers) BSR/ASSE Z X, Minimum Requirements for a Comprehensive Managed Fall Protection Program (revision of ANSI/ASSE Z ) This standard establishes guidelines and requirements for an employer's managed fall protection program, including policies, duties, and training; fall protection procedures; eliminating and controlling fall hazards; rescue procedures; incident investigations; and evaluating program effectiveness. Single copy price: $ Obtain an electronic copy from: TFisher@ASSE.Org Order from: Tim Fisher, (847) , TFisher@ASSE.Org ASSE (ASC A10) (American Society of Safety Engineers) Reaffirmation BSR/ASSE A (R201x), Safety Requirements for Pile Installation and Extraction Operations (reaffirmation of ANSI/ASSE A ) This standard establishes safety requirements for the installation and extraction of piles during construction and demolition operations. Single copy price: $50.00 Obtain an electronic copy from: TFisher@ASSE.Org Order from: Tim Fisher, (847) , TFisher@ASSE.Org

4 Standards Action - July 29, Page 4 of 38 Pages AWS (American Welding Society) New Standard BSR/AWS B x, Standard Welding Procedure Specification (SWPS) for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1, Group 1 or 2) 1/8 inch [3 mm] through 1-1/2 inch [38 mm] Thick, E7018, in the As- Welded or PWHT Condition, Primarily Plate and Structural Applications (new standard) This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for plate and structural applications. Single copy price: $ Obtain an electronic copy from: jrosario@aws.org Order from: Jennifer Rosario, (800) , jrosario@aws.org AWS (American Welding Society) BSR/AWS B x, Standard Welding Procedure Specification (SWPS) for Self-Shielded Flux Cored Arc Welding of Carbon Steel (M-1/P-1, Group 1 or 2) 1/8 inch [3 mm] through 1-1/2 inch [38 mm] Thick, E71T-8, in the As-Welded Condition, Primarily Plate and Structural Applications (revision of ANSI/AWS B ) This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using semiautomatic self-shielded flux cored arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for plate and structural applications. Single copy price: $ Obtain an electronic copy from: jrosario@aws.org Order from: Jennifer Rosario, (800) , jrosario@aws.org AWS (American Welding Society) New Standard BSR/AWS B x, Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding Followed by Shielded Metal Arc Welding of Carbon Steel (M-1/P-1, Group 1 or 2) 1/8 inch [3 mm] through 1-1/2 inch [38 mm] Thick, ER70S-2 and E7018, in the As-Welded or PWHT Condition, Primarily Plate and Structural Applications (new standard) This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using manual gas tungsten arc welding followed by shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for plate and structural applications. Single copy price: $ Obtain an electronic copy from: jrosario@aws.org Order from: Jennifer Rosario, (800) , jrosario@aws.org AWS (American Welding Society) BSR/AWS B x, Standard Welding Procedure Specification (SWPS) for CO2 Shielded Flux Cored Arc Welding of Carbon Steel (M-1/P -1, Group 1 or 2), 1/8 inch [3 mm] through 1-1/2 inch [38 mm] Thick, E70T -1C and E71 T-1C, in the As-Welded Condition, Primarily Plate and Structural Applications (revision of ANSI/AWS B ) This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using semiautomatic CO2 shielded flux cored arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for plate and structural applications. Single copy price: $ Obtain an electronic copy from: jrosario@aws.org Order from: Jennifer Rosario, (800) , jrosario@aws.org AWS (American Welding Society) BSR/AWS B x, Standard Welding Procedure Specification (SWPS) for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1, Group 1 or 2) 1/8 inch [3 mm] through 1-1/2 inch [38 mm] Thick, E6010, in the As- Welded or PWHT Condition, Primarily Plate and Structural Applications (revision of ANSI/AWS B ) This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for plate and structural applications. Single copy price: $ Obtain an electronic copy from: jrosario@aws.org Order from: Jennifer Rosario, (800) , jrosario@aws.org AWS (American Welding Society) BSR/AWS B x, Standard Welding Procedure Specification (SWPS) for 75% Ar/25% CO2 Shielded Flux Cored Arc Welding of Carbon Steel (M-1/P-1, Group 1 or 2), 1/8 inch [3 mm] through 1-1/2 inch [38 mm] Thick, E70T-1M and E71T-1M, in the As-Welded or PWHT Condition, Primarily Plate and Structural Applications (revision of ANSI/AWS B ) This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using semiautomatic Ar/CO2 shielded flux-cored arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for plate and structural applications. Single copy price: $ Obtain an electronic copy from: jrosario@aws.org Order from: Jennifer Rosario, (800) , jrosario@aws.org

5 Standards Action - July 29, Page 5 of 38 Pages AWS (American Welding Society) BSR/AWS B x, Standard Welding Procedure Specification (SWPS) for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1, Group 1 or 2) 1/8 inch [3 mm] through 1-1/2 inch [38 mm] Thick, E6010 (Vertical Uphill) Followed by E7018, in the As-Welded or PWHT Condition, Primarily Plate and Structural Applications (revision of ANSI/AWS B ) This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for plate and structural applications. Single copy price: $ Obtain an electronic copy from: jrosario@aws.org Order from: Jennifer Rosario, (800) , jrosario@aws.org AWS (American Welding Society) BSR/AWS B x, Standard Welding Procedure Specification (SWPS) for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1, Group 1 or 2) 1/8 inch [3 mm] through 1-1/2 inch [38 mm] Thick, E6010 (Vertical Downhill) Followed by E7018, in the As-Welded or PWHT Condition, Primarily Plate and Structural Applications (revision of ANSI/AWS B ) This standard contains the essential welding variables for carbon steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for plate and structural applications. Single copy price: $ Obtain an electronic copy from: jrosario@aws.org Order from: Jennifer Rosario, (800) , jrosario@aws.org AWS (American Welding Society) BSR/AWS B x, Standard Welding Procedure Specification (SWPS) for Shielded Metal Arc Welding of Austenitic Stainless Steel (M-8/P -8 Group 1) 1/8 inch [3 mm] through 1-1/2 inch [38 mm] Thick, in the As- Welded Condition, Primarily Plate and Structural Applications (revision of ANSI/AWS B ) This standard contains the essential welding variables for austenitic stainless steel in the thickness range of 1/8 inch [3 mm] through 1-1/2 inch [38 mm], using manual shielded metal arc welding. It cites the base metals and operating conditions necessary to make the weldment, the filler metal specifications, and the allowable joint designs for fillet and groove welds. This SWPS was developed primarily for plate and structural applications Single copy price: $ Obtain an electronic copy from: jrosario@aws.org Order from: Jennifer Rosario, (800) , jrosario@aws.org AWS (American Welding Society) BSR/AWS C3.2M/C X, Standard Method For Evaluating the Strength of Brazed Joints (revision of ANSI/AWS C3.2M/C ) This standard describes the test methods used to obtain brazed strength data of the short-time testing of single-lap joints in shear, butt-tension, stress-rupture, creep-strength, four-point-bending, and ceramic-tensilebutton specimens. Specimen preparation methods, brazing procedures, testing techniques, and methods for data analysis are detailed. Sample forms for recording data are presented. A graphical method of data presentation relates shear stress to overlap distance. Single copy price: $34.00 Obtain an electronic copy from: jdouglass@aws.org Order from: John Douglass, (800) , jdouglass@aws.org AWWA (American Water Works Association) BSR/AWWA C111/A x, Rubber-Gasket Joints for Ductile Iron Pressure Pipe and Fittings (revision of ANSI/AWWA C111/A ) This standard describes rubber-gasket joints of the following types for ductile-iron pressure pipe and ductile-iron and gray-iron fittings, valves, hydrants, and other appurtenances for potable water, raw water, nonaggressive wastewater and reclaimed water supply service. Single copy price: $20.00 Obtain an electronic copy from: vdavid@awwa.org Order from: Paul Olson, (303) , polson@awwa.org; vdavid@awwa. org CTA (Consumer Technology Association) New Standard BSR/CTA x, Physical Activity Monitoring for Fitness Wearables - Step Counting (new standard) This standard creates definitions and performance criteria for measuring step counting on consumer wearable or app-based physical activity monitoring devices. Single copy price: $55.00 Obtain an electronic copy from: standards@cta.tech Order from: Veronica Lancaster, (703) , vlancaster@cta.tech

6 Standards Action - July 29, Page 6 of 38 Pages HL7 (Health Level Seven) BSR/HL7 V3 RBAC, R3-201x, HL7 Version 3 Standard: Healthcare (Security and Privacy) Access Control Catalog, Release 3 (revision and redesignation of ANSI/HL7 V3 RBAC, R2-2010) The Security WG would like to take the opportunity to add additional access control data to further extend elements of the current normative Role-based Access Control Permission Catalog standard. The new Healthcare Security and Privacy Access Control document will include Attribute-based Access Control (ABAC) and Relationship Access Control (ReBAC). With these substantive additions, the Security WG voted not to proceed with the reaffirmation of the current HL7 RBAC Permission Catalog and proceed with a new ballot document. Single copy price: Free to members; free to non-members 90 days following ANSI approval and publication by HL7 Obtain an electronic copy from: Karenvan@HL7.org Order from: Karen Van Hentenryck, (734) , Karenvan@HL7.org RESNET (Residential Energy Services Network, Inc.) Addenda BSR/RESNET/ICC Addendum D-201x, Testing Airtightness of Building Enclosures, Airtightness of Heating and Cooling Air Distribution Systems, and Airflow of Mechanical Ventilation Systems: Reference Standard ANSI/RESNET/ICC (addenda to ANSI/RESNET ) Revise Standard ANSI/RESNET/ICC to replace references to RESNET Mortgage Industry National Home Energy Rating Standards, Chapter 8 sections with references to Standard ANSI/RESNET/ICC for like requirements. Single copy price: $55.00 Obtain an electronic copy from: Electronic copy can be downloaded from the RESNET website at Order from: Rick Dixon, Standards Manager, RESNET, P.O. Box 4561, Oceanside, CA Send comments (with copy to psa@ansi.org) to: Comments are submitted via RESNET's online comment form. See the links from webpage: http: // MHI (Material Handling Industry) New Standard BSR MH x, Power-Operated Vertical Carousels and Vertical Lift Modules (new standard) This proposed Standard applies to power-operated storage equipment typically referred to as vertical storage carousels and vertical lift modules. The objective of this standard is to provide guidance to the user so they may eliminate or minimize the hazards described within Section 4 of the proposed standard. These hazards can arise during installation, start-up, operation, maintenance, testing, and dismantling of the equipment. Single copy price: $10.00 Order from: Patrick Davison, (704) , pdavison@mhi.org TIA (Telecommunications Industry Association) BSR/TIA 1183-A-201x, Measurement Methods and Test Fixtures for Balunless Measurements of Balanced Components and Systems (revision and redesignation of ANSI/TIA ) This Standard will supersede ANSI/TIA 1183 and its addendum It is intended to incorporate and revise as necessary the content of those Standards. Single copy price: $ Obtain an electronic copy from: standards@tiaonline.org Order from: TIA Send comments (with copy to psa@ansi.org) to: standards@tiaonline.org NEMA (ASC C8) (National Electrical Manufacturers Association) BSR ICEA S x, Telecommunications Cable Aircore, Polyolefin Insulated, Copper Conductor Technical Requirements (revision of ANSI ICEA S ) This Standard covers mechanical and electrical requirements for aircore, polyolefin insulated, copper conductor telecommunications cable. It provides alternative choices for type of insulation, core assembly, color code, sheath design (shielding materials, single or double jackets, and jacket thickness), and screened or non-screened core. Single copy price: $ Order from: Kevin Connelly, (703) , Kevin.Connelly@Nema.org UL (Underwriters Laboratories, Inc.) Reaffirmation BSR/UL (R201x), Standard for Safety for Electric Spas, Equipment Assemblies, and Associated Equipment (reaffirmation of ANSI/UL ) These requirements apply to self-contained spas. They also apply to fieldinstalled equipment assemblies, blowers, and controls for use with fieldinstalled hot tubs, swimming pools, and non-self-contained spas. These products are for household or commercial use, indoors, outdoors, or both. All equipment is intended for installation and use in accordance with Article 680 of the National Electrical Code, NFPA 70. These requirements also apply to field-installed accessories that have been investigated with the basic product. Single copy price: Contact comm2000 for pricing and delivery options Obtain an electronic copy from: Order from: comm2000 Send comments (with copy to psa@ansi.org) to: Megan Monsen, (847) , megan.monsen@ul.com

7 Standards Action - July 29, Page 7 of 38 Pages UL (Underwriters Laboratories, Inc.) Reaffirmation BSR/UL (R201x), Standard for Safety for Communications - Circuit Accessories (reaffirmation of ANSI/UL (R2012)) These requirements cover telecommunications-circuit accessories, such as jack and plug assemblies, quick-connect terminal assemblies, telephone wall plates, telephone extension cords, cross-connect terminal-block assemblies, maintenance terminal modules, terminal enclosures, cable-splice enclosures, network-interface devices, wire-guide assemblies, and connector boxes. These devices are intended to be used in telecommunications networks that have an operating root-mean-square (rms) voltage to ground less than 150 volts and installed or used in accordance with the National Electrical Code, ANSI/NFPA 70. Single copy price: Contact comm2000 for pricing and delivery options Obtain an electronic copy from: Order from: comm2000 Send comments (with copy to psa@ansi.org) to: Megan Monsen, (847) , megan.monsen@ul.com ASME (American Society of Mechanical Engineers) Reaffirmation BSR/ASME B (R201x), Wood Screws (Inch Series) (reaffirmation of ANSI/ASME B (R2008)) This standard covers the complete general and dimensional data for the various types of dotted and recessed head wood screws recognized as "American National Standard." Also included are appendixes that provide specifications and instructions for penetration gaging and wobble gaging of recessed head screws; documentation for screw-head types relegated to non-preferred status; and formulas on which dimensional data are based. It shall be understood, however, that where questions arise concerning acceptance of product, the dimensions given in the tables shall govern over recalculation by formula. Single copy price: $35.00 For Reaffirmations and Withdrawn standards, please view our catalog at Send comments (with copy to psa@ansi.org) to: Angel Guzman, (212) , guzman@asme.org UL (Underwriters Laboratories, Inc.) BSR/UL X, Standard for Safety for Household Electric Coffee Makers and Brewing-Type Appliances (Proposals dated 7/29/16) (revision of ANSI/UL ) (1) Addition of transient voltage testing; (2) Proposed changes to the hospitality-use supplement, supplement SB; (3) Addition of Insertion/Withdrawal Test for Electric Kettles, New Section 51A. Single copy price: Contact comm2000 for pricing and delivery options Obtain an electronic copy from: Order from: comm2000 Send comments (with copy to psa@ansi.org) to: Linda Phinney, (510) , Linda.L.Phinney@ul.com Comment Deadline: September 27, 2016 ASME (American Society of Mechanical Engineers) Reaffirmation BSR/ASME B (R201x), Chucks and Chuck Jaws (reaffirmation of ANSI/ASME B (R2011)) This Standard applies to chucks for use on engine lathes, tool room lathes, turret lathes, and automatic lathes and fit American Standard Spindle Noses of ANSI B They may be used on other applications for which they are suitable (see pages 4 and 5 of ANSI-B ). It is within the scope of this Standard to establish: (a) duty classes; (b) standard chuck diameters; (c) top jaw interchangeability; (d) mounting interchangeability (USA-Standard Spindle Noses); (e) draw-bar interchangeability for power chucks; (f) identification code for body, master jaws, top jaws dimensions, where interchangeability of chucks may be involved; and (g) nomenclature. Single copy price: $50.00 For Reaffirmations and Withdrawn standards, please view our catalog at Send comments (with copy to psa@ansi.org) to: Donnie Alonzo, (212) , dalonzo@asme.org ASME (American Society of Mechanical Engineers) Reaffirmation BSR/ASME B (R201X), Drop Forged Rivetless Chains, Sprockets Teeth Drive Chain/Drive Dogs (reaffirmation of ANSI/ASME B (R2009)) This Standard covers chains made from drop-forged steel parts that are heat-treated and are proportioned for high strength and comparative light weight. These chains' simple design permits assembly or dismantling by hand; these chains are available in three general types - Regular dropforged rivetless chain, X-type chain, and Modified X-type rivetless chain - as illustrated and described in this Standard. Numerous attachments are available to suit a wide variety of applications. Single copy price: $39.00 For Reaffirmations and Withdrawn standards, please view our catalog at Send comments (with copy to psa@ansi.org) to: Remington Richmond, (212) , richmondr@asme.org ASME (American Society of Mechanical Engineers) Reaffirmation BSR/ASME B29.24M-2002 (R201x), Roller Load Chains for Overhead Hoists (reaffirmation of ANSI/ASME B29.24M-2002 (R2009)) This Standard covers specialized roller chains that are designed specifically as load chains for use in overhead hoists. Single copy price: $42.00 For Reaffirmations and Withdrawn standards, please view our catalog at Send comments (with copy to psa@ansi.org) to: Remington Richmond, (212) , richmondr@asme.org

8 Technical Reports Registered with ANSI Technical Reports Registered with ANSI are not consensus documents. Rather, all material contained in Technical Reports Registered with ANSI is informational in nature. Technical reports may include, for example, reports of technical research, tutorials, factual data obtained from a survey carried out among standards developers and/or national bodies, or information on the "state of the art" in relation to standards of national or international bodies on a particular subject. Immediately following the end of a 30-day announcement period in Standards Action, the Technical Report will be registered by ANSI. Please submit any comments regarding this registration to the organization indicated, with a copy to the PSA Center, American National Standards Institute, 25 West 43rd Street, New York, NY or to psa@ansi.org. Standards Action - July 29, Page 8 of 38 Pages ARMA (ARMA International) ARMA International TR , Glossary of Records and Information Management Terms, 5th Edition (TECHNICAL REPORT) (technical report) With this revision, content has been updated, as appropriate. Many terms from numerous disciplines having an impact on records and information management have been included. Technical terms from archival or library science concepts and for specific technologies have been excluded. Single copy price: $TBD Order from: ARMA International Online Bookstore at org/go/prod/v5032 Send comments (with copy to psa@ansi.org) to: standards@armaintl.org Correction Approval Dates ANSI/NSF 50 Two parts of ANSI/NSF 50 were listed in Standards Action with errors in their approval information. The errors were as follows: ANSI/NSF 50 (i98r1) - ANSI approved the standard on March 8, 2016, but was listed as administratively approved in the March 18, 2016 issue of Standards Action. ANSI/NSF 50 (i92r1) - ANSI listed the approval date as January 27, 2016, but the actual approval date is March 8, The records for these standards have been updated.

9 Standards Action - July 29, Page 9 of 38 Pages Call for Members (ANS Consensus Bodies) Directly and materially affected parties who are interested in participating as a member of an ANS consensus body for the standards listed below are requested to contact the sponsoring standards developer directly and in a timely manner. AAMI (Association for the Advancement of Medical Instrumentation) Office: 4301 N Fairfax Drive Suite 301 Arlington, VA Phone: Colleen Elliott (703) (703) celliott@aami.org BSR/AAMI CN27-201x, General requirements for small-bore connector actuated valves incorporated into medical devices (new standard) BSR/AAMI EQ94-201x, Healthcare technology acquisition (new standard) ASA (ASC S12) (Acoustical Society of America) Office: Phone: 1305 Walt Whitman Rd Suite 300 Melville, NY Neil Stremmel (631) (631) nstremmel@acousticalsociety.org BSR ASA S x/Part 4, Acoustical Performance Criteria, Design Requirements, and Guidelines for Schools, Part 4: Physical Education Settings (new standard) ASSE (ASC A10) (American Society of Safety Engineers) Office: Phone: 520 N. Northwest Highway Park Ridge, IL Tim Fisher (847) (847) TFisher@ASSE.org BSR/ASSE A (R201x), Safety & Health Program Requirements for Demolition Operations (reaffirmation of ANSI/ASSE A ) Obtain an electronic copy from: Tim Fisher BSR/ASSE A (R201x), Safety Requirements for Excavation (reaffirmation of ANSI ASSE A (R2010)) Obtain an electronic copy from: Tim Fisher BSR/ASSE A (R201x), Safety Requirements for Pile Installation and Extraction Operations (reaffirmation of ANSI/ASSE A ) Obtain an electronic copy from: Tim Fisher BSR/ASSE A (R201x), Safe Operating Practices for Tile, Terrazzo, and Marble Work (reaffirmation of ANSI/ASSE A (R2011)) Obtain an electronic copy from: Tim Fisher BSR/ASSE A (R201x), Safety and Health Program Requirements for Multi-Employer Program - Standard for Construction and Demolition Operations (reaffirmation of ANSI ASSE A ) Obtain an electronic copy from: Tim Fisher BSR/ASSE A X, Debris Net Systems Used during Construction and Demolition Operations (new standard) Obtain an electronic copy from: Tim Fisher ASSE (ASC Z359) (American Society of Safety Engineers) Office: Phone: 520 N. Northwest Highway Park Ridge, IL Tim Fisher (847) (847) TFisher@ASSE.org BSR/ASSE Z X, Minimum Requirements for a Comprehensive Managed Fall Protection Program (revision of ANSI ASSE Z ) Obtain an electronic copy from: Tim Fisher CTA (Consumer Technology Association) Office: Phone: 1919 South Eads Street Arlington, VA Veronica Lancaster (703) (703) vlancaster@cta.tech BSR/CTA x, Physical Activity Monitoring for Heart Rate and Related Measures (new standard) BSR/CTA x, Physical Activity Monitoring for Fitness Wearables - Step Counting (new standard) Obtain an electronic copy from: standards@cta.tech BSR/ASSE A (R201x), Safety Requirements for Tunnels, Shafts, and Caissons Standard for Construction and Demolition Operations (reaffirmation of ANSI/ASSE A ) Obtain an electronic copy from: Tim Fisher

10 Standards Action - July 29, Page 10 of 38 Pages ISA (International Society of Automation) Office: Phone: 67 Alexander Drive Research Triangle Park, NC Charles Robinson (919) (919) crobinson@isa.org BSR/ISA x, Functional Safety: Safety Controls, Alarms, and Interlocks for the Process Sector (new standard) NSF (NSF International) Office: Phone: 789 N. Dixboro Road Ann Arbor, MI Lauren Panoff (734) lpanoff@nsf.org BSR/NSF x (i91r2), Equipment for Swimming Pools, Spas, Hot Tubs and Other Recreational Water Facilities (revision of ANSI/NSF ) SMACNA (Sheet Metal and Air-Conditioning Contractors' National Association) Office: 4201 Lafayette Center Drive Chantilly, VA Phone: Sue Baker (703) (703) sbaker@smacna.org BSR/SMACNA x, Thermoset FRP Duct Construction Manual (new standard) TAPPI (Technical Association of the Pulp and Paper Industry) Office: Phone: 15 Technology Parkway South Peachtree Corners, GA Laurence Womack (770) (770) standards@tappi.org BSR/TAPPI T 834 om-201x, Determination of containerboard roll hardness (revision of ANSI/TAPPI T 834 om-2012) TIA (Telecommunications Industry Association) Office: Phone: 1320 North Courthouse Road Suite 200 Arlington, VA Teesha Jenkins (703) (703) standards@tiaonline.org BSR/TIA 1183-A-201x, Measurement Methods and Test Fixtures for Balun-less Measurements of Balanced Components and Systems (revision and redesignation of ANSI/TIA ) Obtain an electronic copy from: TIA

11 Standards Action - July 29, Page 11 of 38 Pages Call for Members (ANS Consensus Bodies) Call for Committee Members ASC O1 Are you interested in contributing to the development and maintenance of valuable industry safety standards? The ASC O1 is currently looking for members in the following categories: o General Interest o Government o Producer o User If you are interested in joining the ASC O1, contact WMMA Associate Director Jennifer Miller at jennifer@wmma.org.

12 Standards Action - July 29, Page 12 of 38 Pages Final Actions on American National Standards The standards actions listed below have been approved by the ANSI Board of Standards Review (BSR) or by an ANSI-Audited Designator, as applicable. * ABYC (American Boat and Yacht Council) ANSI/ABYC H , Powering of Boats (revision of ANSI/ABYC H ): 7/13/2016 AHRI (Air-Conditioning, Heating, and Refrigeration Institute) ANSI/AHRI Standard , Sound Rating of Non-Ducted Indoor Air-Conditioning Equipment (revision of ANSI/AHRI Standard ): 7/15/2016 AISC (American Institute of Steel Construction) ANSI/AISC , Seismic Provisions for Structural Steel Buildings (revision of ANSI/AISC ): 7/12/2016 ANS (American Nuclear Society) New Standard ANSI/ANS , Earthquake Instrumentation Criteria for Nuclear Power Plants (new standard): 7/14/2016 ASA (ASC S1) (Acoustical Society of America) New National Adoption ANSI/ASA S /Part 3/IEC :2016, Electroacoustics - Octave-Band and Fractional-Octave Band Filters - Part 3: Periodic Tests (identical national adoption of IEC :2016): 7/19/2016 ANSI/ASA S /Part 2 / IEC :2016, Electroacoustics - Octave-Band and Fractional-Octave-Band Filters - Part 2: Pattern- Evaluation Tests (identical national adoption of IEC :2016): 7/19/2016 ASA (ASC S12) (Acoustical Society of America) New Standard ANSI/ASA S , Criteria for Evaluating Speech Privacy in Health Care Facilities (new standard): 7/19/2016 Reaffirmation ANSI/ASA S /ISO (R2016), Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering/survey methods for use in situ in a reverberant environment (reaffirmation of ANSI/ASA S /ISO ): 7/19/2016 ASABE (American Society of Agricultural and Biological Engineers) New National Adoption ANSI/ASABE AD JUL2016, Agricultural machinery - Safety - Part 12: Rotary disc and drum mowers and flail mowers (identical national adoption of ISO :2012): 7/13/2016 ASB (ASC Z50) (American Society of Baking) Reaffirmation ANSI/ASB Z (R2016), Bakery Equipment - Safety Standards (reaffirmation of ANSI ASB Z (R2011)): 7/14/2016 ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.) Addenda ANSI/ASHRAE 15b-2016, Safety Standard for Refrigeration Systems (addenda to ANSI/ASHRAE Standard ): 6/30/2016 ANSI/ASHRAE 34ad-2016, Designation and Safety Classification of Refrigerants (addenda to ANSI/ASHRAE Standard ): 6/30/2016 ANSI/ASHRAE 34af-2016, Designation and Safety Classification of Refrigerants (addenda to ANSI/ASHRAE Standard ): 6/30/2016 ANSI/ASHRAE 34ag-2016, Designation and Safety Classification of Refrigerants (addenda to ANSI/ASHRAE Standard ): 6/30/2016 ANSI/ASHRAE 34ah-2016, Designation and Safety Classification of Refrigerants (addenda to ANSI/ASHRAE Standard ): 6/30/2016 ANSI/ASHRAE 34ai-2016, Designation and Safety Classification of Refrigerants (addenda to ANSI/ASHRAE Standard ): 6/30/2016 ANSI/ASHRAE 34y-2016, Designation and Safety Classification of Refrigerants (addenda to ANSI/ASHRAE Standard ): 6/30/2016 ANSI/ASHRAE 34z-2016, Designation and Safety Classification of Refrigerants (addenda to ANSI/ASHRAE Standard ): 6/30/2016 ANSI/ASHRAE 62.2k-2016, Ventilation and Acceptable Indoor Air Quality in Low-Rise Residential Buildings (addenda to ANSI/ASHRAE Standard ): 6/30/2016 ANSI/ASHRAE 62.2q-2016, Ventilation and Acceptable Indoor Air Quality in Low-Rise Residential Buildings (addenda to ANSI/ASHRAE Standard ): 6/30/2016 ANSI/ASHRAE 145.2d-2016, Laboratory Test Methods for Assessing the Performance of Gas-Phase Air Cleaning Systems: Air Cleaning Devices (addenda to ANSI/ASHRAE Standard ): 7/1/2016 ANSI/ASHRAE/IES 90.1ds-2016, Energy Standard for Buildings Except Low-Rise Residential Buildings (addenda to ANSI/ASHRAE/IES Standard ): 6/30/2016 ANSI/ASHRAE/IES 90.1dv-2016, Energy Standard for Buildings Except Low-Rise Residential Buildings (addenda to ANSI/ASHRAE/IESNA Standard ): 6/30/2016 ANSI/ASHRAE/USGBC/IES 189.1f-2016, Standard for the Design of High-Performance Green Buildings Except Low-Rise Residential Buildings (addenda to ANSI/ASHRAE/USGBC/IES Standard ): 6/30/2016

13 Standards Action - July 29, Page 13 of 38 Pages ANSI/ASHRAE/SMACNA Standard , Method of Testing HVAC Air Ducts (revision of ANSI/ASHRAE/SMACNA Standard ): 7/1/2016 ASME (American Society of Mechanical Engineers) Reaffirmation ANSI/ASME A /CSA B (R2016), Flush Valves and Spuds for Water Closets, Urinals, and Tanks (reaffirmation of ANSI/ASME A /CSA B ): 7/14/2016 ANSI/ASME V&V (R2016), Guide for Verification and Validation in Computational Solid Mechanics (reaffirmation of ANSI/ASME V&V ): 7/19/2016 ANSI/ASME B , Stacker Cranes (Top or Under Running Bridge, Multiple Girder with Top or Under Running Trolley Hoist) (revision of ANSI/ASME B ): 7/8/2016 ASTM (ASTM International) ANSI/ASTM D , Specification for Aviation Turbine Fuels (revision of ANSI/ASTM D ): 6/21/2016 ANSI/ASTM D , Test Method for Ignition Characteristics of Finished Textile Floor Covering Materials (revision of ANSI/ASTM D ): 6/21/2016 ANSI/ASTM D , Practice for Utilization of Test Data to Determine Conformance with Specifications (revision of ANSI/ASTM D a): 6/21/2016 ANSI/ASTM D , Specification for Fuel System Icing Inhibitors (revision of ANSI/ASTM D ): 6/21/2016 ANSI/ASTM D , Specification for Rigid (Unplasticized) Poly (Vinyl Chloride) (PVC) Soffit (revision of ANSI/ASTM D ): 6/28/2016 ANSI/ASTM D b, Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material (revision of ANSI/ASTM D ): 6/21/2016 ANSI/ASTM D , Test Method for Relative Rigidity of Poly (Vinyl Chloride)(PVC) Siding (revision of ANSI/ASTM D (R2010)): 6/28/2016 ANSI/ASTM D a, Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons (revision of ANSI/ASTM D b): 6/21/2016 ANSI/ASTM D , Specification for High Aromatic Content Unleaded Hydrocarbon Aviation Gasoline (revision of ANSI/ASTM D A): 6/21/2016 ANSI/ASTM E8-2016, Test Methods for Tension Testing of Metallic Materials (revision of ANSI/ASTM E8-2015a): 7/15/2016 ANSI/ASTM E b, Test Methods for Notched Bar Impact Testing of Metallic Materials (revision of ANSI/ASTM E a): 6/21/2016 ANSI/ASTM E , Test Method for Surface Burning Characteristics of Building Materials (revision of ANSI/ASTM E a): 7/1/2016 ANSI/ASTM E a, Test Methods for Fire Tests of Building Construction and Materials (revision of ANSI/ASTM E ): 7/1/2016 * * * ANSI/ASTM E , Guide for Development of Fire-Risk- Assessment Standards (revision of ANSI/ASTM E ): 6/21/2016 ANSI/ASTM E , Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics (revision of ANSI/ASTM E ): 7/1/2016 ANSI/ASTM E , Practice for Ignition Sources (revision of ANSI/ASTM E ): 6/21/2016 ANSI/ASTM F , Test Method for Impact Attenuation of Playing Surface Systems and Materials (revision of ANSI/ASTM F a): 7/1/2016 ANSI/ASTM F , Consumer Safety Specification for Toy Safety (revision of ANSI/ASTM F ): 7/1/2016 ANSI/ASTM F , Test Method for Performance of Refrigerated Buffet and Preparation Tables (revision of ANSI/ASTM F (R2010)): 6/28/2016 ANSI/ASTM F , Practice for Validation, Calibration, and Certification of Walkway Tribometers Using Reference Surfaces (revision of ANSI/ASTM F ): 7/1/2016 NEMA (ASC C78) (National Electrical Manufacturers Association) Stabilized Maintenance ANSI C (S2016), Standard for Electric Lamps: Method for the Designation of Glow Lamps (stabilized maintenance of ANSI C (R2011)): 7/12/2016 NEMA (ASC C82) (National Electrical Manufacturers Association) Reaffirmation ANSI C (R2016), Standard for Lamp Ballasts - Method of Measurement of Fluorescent Lamp Ballasts (reaffirmation of ANSI C (R2007)): 7/12/2016 ANSI C , Lamp Ballasts - High-Intensity Discharge and Low- Pressure Sodium Lamps - Definitions (revision and redesignation of ANSI ANSLG C ): 7/12/2016 Withdrawal ANSI C (R2010), Standard for Lamp Ballasts - Fluorescent Adapters (withdrawal of ANSI C (R2010)): 7/12/2016 NIST/ITL (National Institute of Standards and Technology/Information Technology Laboratory) ANSI/NIST-ITL Update:2015, Data Format for the Interchange of Fingerprint, Facial & Other Biometric Information (revision, redesignation and consolidation of ANSI/NIST-ITL Update:2013): 7/14/2016 NSF (NSF International) ANSI/NSF (i15r1), Commercial Refrigerators and Freezers (revision of ANSI/NSF ): 7/7/2016 ANSI/NSF (i72r1), Plastics piping system components and related materials (revision of ANSI/NSF ): 7/1/2016

14 Standards Action - July 29, Page 14 of 38 Pages * ANSI/NSF (i73r1), Plastics piping system components and related materials (revision of ANSI/NSF ): 7/12/2016 * * * * * * * * ANSI/NSF (i99r1), Equipment for Swimming Pools, Spas, Hot Tubs and Other Recreational Water Facilities (revision of ANSI/NSF ): 7/7/2016 ANSI/NSF (i114r1), Equipment for Swimming Pools, Spas, Hot Tubs and Other Recreational Water Facilities (revision of ANSI/NSF ): 7/7/2016 UL (Underwriters Laboratories, Inc.) New Standard ANSI/UL , Standard for Safety for Air Dispersion Systems (new standard): 7/12/2016 Reaffirmation ANSI/UL (R2016), Receptacles and Switches Intended for Use with Aluminum Wire (reaffirmation of ANSI/UL ): 7/15/2016 ANSI/UL (R2016), Standard for Safety for Track Lighting Systems (reaffirmation of ANSI/UL ): 7/12/2016 ANSI/UL (R2016), Wiring Device Configurations (reaffirmation of ANSI/UL ): 7/15/2016 ANSI/UL (R2016), Standard for Safety for Information Technology Equipment - Safety - Part 21: Remote Power Feeding (reaffirmation of ANSI/UL (R2012)): 7/8/2016 ANSI/UL (R2016), Standard for Safety for Information Technology Equipment - Safety - Part 23: Large Data Storage Equipment (reaffirmation of ANSI/UL (R2012)): 7/8/2016 ANSI/UL c, Standard for Safety for Smoke Detectors for Fire Alarm Systems (revision of ANSI/UL ): 7/15/2016 ANSI/UL , Standard for the Safety of Hose Valves for Fire- Protection Service (Proposal dated 05/27/2016) (revision of ANSI/UL (R2012)): 7/12/2016 ANSI/UL 746C-2016, Standard for Safety for Polymeric Materials - Use in Electrical Equipment Evaluations (revision of ANSI/UL 746C -2015): 7/18/2016 ANSI/UL , Standard for Safety for Refrigerated Vending Machines (revision of ANSI/UL ): 7/18/2016 ANSI/UL , Standard for Safety for Household Electric Skillets and Frying-Type Appliances (Proposal dated 3/11/16) (revision of ANSI/UL ): 7/15/2016 ANSI/UL a, Standard for Safety for Household Electric Skillets and Frying-Type Appliances (Proposals dated 4/15/16) (revision of ANSI/UL ): 7/15/2016 ANSI/UL , Standard for Safety for Electric Duct Heaters (revision of ANSI/UL ): 7/14/2016

15 Project Initiation Notification System (PINS) Standards Action - July 29, Page 15 of 38 Pages ANSI Procedures require notification of ANSI by ANSI-accredited standards developers (ASD) of the initiation and scope of activities expected to result in new or revised American National Standards (ANS). Early notification of activity intended to reaffirm or withdraw an ANS and in some instances a PINS related to a national adoption is optional. The mechanism by which such notification is given is referred to as the PINS process. For additional information, see clause 2.4 of the ANSI Essential Requirements: Due Process Requirements for American National Standards. Following is a list of proposed actions and new ANS that have been received recently from ASDs. Please also review the section in Standards Action entitled "American National Standards Maintained Under Continuous Maintenance" for additional or comparable information with regard to standards maintained under the continuous maintenance option. To view information about additional standards for which a PINS has been submitted and to search approved ANS, please visit which is a database of standards information. Note that this database is not exhaustive. Directly and materially affected interests wishing to receive more information or to submit comments are requested to contact the standards developer directly within 30 days of the publication of this announcement. AAMI (Association for the Advancement of Medical Instrumentation) Office: 4301 N. Fairfax Dr., Suite 301 Arlington, VA Amanda Benedict (703) abenedict@aami.org BSR/AAMI EQ94-201x, Healthcare technology acquisition (new standard) Stakeholders: Healthcare delivery organizations, regulators, manufacturers Project Need: Without a formal process in place for acquiring healthcare technology, and without involving the necessary players in the process, the approach to acquisition can become disorganized and disjointed. The ripple effects of such an approach can be very problematic. This standard will provide guidance for healthcare delivery organizations on the acquisition of healthcare technology, with the goal of having a consistent process and standardized set of topics that should be covered in acquisition process. Ultimately, standardization will benefit both healthcare delivery organizations and vendors. Topics may include service documentation, risk management files, processes for making purchasing decisions (including who should be involved in those decisions), depreciation schedules, monitoring of hazard alerts/product recalls, identifying technical specifications, and a standardized request for proposals (RFP). AAMI (Association for the Advancement of Medical Instrumentation) Office: 4301 N Fairfax Drive Suite 301 Arlington, VA Colleen Elliott (703) celliott@aami.org BSR/AAMI CN27-201x, General Requirements for small-bore connector actuated valves incorporated into medical devices (new standard) Stakeholders: manufacturers, clinicians Project Need: standardization of small-bore connector actuated valves to reduce clinical risks This standard specifies general requirements for small-bore connectoractuated valves incorporated into or used with medical devices used in clinical applications of medical devices and related accessories. ANS (American Nuclear Society) Office: 555 North Kensington Avenue La Grange Park, IL Kathryn Murdoch (708) kmurdoch@ans.org BSR/ANS x, A Guide for Acquisition and Documentation of Reference Power Reactor Physics Measurements for Nuclear Analysis Verification (new standard) Stakeholders: Commercial nuclear power industry and vendors. Project Need: This standard is needed because developments in reactor technology have made some terminology obsolete and developments in formal standardization related to the measurement of reactor physics parameters are needed. This standard is needed because it provides guidance and criteria for the selection of power reactor measured quality data for use in the benchmarking of reactor physics neutronics methods/codes. This standard specifies and provides requirements for the reference measurements of reactor geometry, reactivity, and operation parameters in light-water power reactors. The measurement data are used in the verification of reactor physics computational methods used for nuclear core designs and analyses. The standard identifies the types of parameters, a brief description of test conditions and experimental data required for such reference measurements, problems and concerns that may affect the accuracy or interpretation of the data, and criteria to be used in documenting the results of reference measurements.

16 Standards Action - July 29, Page 16 of 38 Pages * ASA (ASC S12) (Acoustical Society of America) Office: 1305 Walt Whitman Rd Suite 300 Melville, NY Neil Stremmel (631) nstremmel@acousticalsociety.org BSR/ASA S x/Part 4, Acoustical Performance Criteria, Design Requirements, and Guidelines for Schools, Part 4: Physical Education Settings (new standard) Stakeholders: School administrators, purchasing agents, school architects and designers, teachers and parents. Project Need: The goal of this standard is to bring physical education teaching settings in line with standards set for typical classroom learning spaces. This part of ANSI/ASA S12.60 is intended to provide a minimum set of requirements, based on the best scientific evidence available, that can be adopted by reference to this standard and enforced by an authority having jurisdiction. This part is intended to help school planners and designers provide good acoustical characteristics for physical education spaces in which speech communication is an important part of the learning process. ASABE (American Society of Agricultural and Biological Engineers) Office: 2920 Niles Rd. St. Joseph, MI Walter Brace brace@asabe.org BSR/ASABE S623.1 MONYEAR-201x, Determining Landscape Plant Water Demands (revision and redesignation of ANSI/ASABE S ) Stakeholders: Irrigation consultants and designers, irrigation managers, Irrigation contractors and maintenance personnel, governmental agencies, water purveyors, building and property managers, voluntary sustainable building programs. Project Need: To correct a formula error. The process to determine available water for landscapes and estimate the amount of water required to maintain the landscape so that it will function appropriately for its intended purpose. The standardized method can be utilized by water agencies, regulators, property owners, or landscape managers to determine if the anticipated plant water demand is equal to or less than the site-available water resources. AWS (American Welding Society) Office: 8669 NW 36th Street #130 Miami, FL John Douglass jdouglass@aws.org BSR/AWS C3.4M/C x, Specification for Torch Brazing (revision of ANSI/AWS C3.4M/C ) Stakeholders: Engineers, Torch Brazers, Quality Controllers Project Need: To provide the minimum fabrication, equipment, and process procedure requirements, as well as inspection requirements for torch brazing. This specification presents the minimum fabrication, equipment, and process procedure requirements, as well as inspection requirements for the torch brazing of steels, stainless steels, copper, copper alloys, and heat- or corrosion-resistant alloys, and other materials that can be adequately torch brazed (the torch brazing of aluminum alloys is addressed in AWS C3.7M/C3.7, Specification for Aluminum Brazing). This specification provides criteria for classifying torch-brazed joints based on loading and the consequences of failure and quality assurance criteria defining the limits of acceptability in each class. BSR/AWS C3.5M/C x, Specification for Induction Brazing (revision of ANSI/AWS C3.5M/C ) Stakeholders: Engineers, Induction Brazers, Quality Controllers Project Need: To provide the minimum fabrication, equipment, and process procedure requirements, as well as inspection requirements for induction brazing. This specification provides the minimum fabrication, equipment, and process-procedure requirements, as well as inspection requirements for the induction brazing of steels, copper, copper alloys, and heat- and corrosion-resistant alloys, and other materials that can be adequately induction brazed (the induction brazing of aluminum alloys is addressed in AWS C3.7M/C3.7, Specification for Aluminum Brazing). This specification provides criteria for classifying induction brazed joints based on loading and the consequences of failure and quality assurance criteria defining the limits of acceptability in each class. BSR/AWS C3.6M/C x, Specification for Furnace Brazing (revision of ANSI/AWS C3.6M/C ) Stakeholders: Engineers, furnace brazers, quality controllers. Project Need: To provide the minimum fabrication, equipment, and process procedure requirements, as well as inspection requirements for furnace brazing. This specification provides the minimum fabrication, equipment, material, process-procedure requirements, as well as inspection requirements for the furnace brazing of steels, copper, copper alloys, and heat- and corrosion-resistant alloys and other materials that can be adequately furnace brazed (the furnace brazing of aluminum alloys is addressed in AWS C3.7M/C3.7, Specification for Aluminum Brazing). This specification provides criteria for classifying furnace-brazed joints based on loading and the consequences of failure and quality assurance criteria defining the limits of acceptability in each class.

17 Standards Action - July 29, Page 17 of 38 Pages * * * CSA (CSA Group) Office: 8501 East Pleasant Valley Rd. Cleveland, OH Cathy Rake (216) cathy.rake@csagroup.org BSR Z x, Elastomeric Composite Hose and Hose Couplings for Conducting Propane and Natural Gas (same as CSA 8.1) (new standard) Stakeholders: Consumers, manufacturers, gas suppliers, and certifying agencies. Project Need: Harmonization. This Standard applies to newly produced Type I, Type II, and Type III hose used for the transfer or conducting of propane and natural gas capable of operation at temperatures between -40 F (-40 C) and 140 F (60 C). Type I hose refers to hose with a maximum operating pressure of 350 psig (2.4 MPa) and a minimum burst pressure of 1750 psig (12.1 MPa). Type II and Type III hose refers to stainless steel braid reinforced hose designed with a maximum operating pressure of 350 psig (2.4 MPa) and a minimum burst pressure depending on hose size and nominal ID. BSR Z x, Thermoplastic Hose and Hose Couplings for Conducting Propane and Natural Gas (same as CSA 8.3) (new standard) Stakeholders: Consumers, manufacturers, gas suppliers, and certifying agencies. Project Need: Harmonization. This Standard applies to newly produced thermoplastic hose, hose couplings, and complete assemblies of hose and couplings used to conduct natural gas in a gaseous state and propane in either a liquid or gaseous state to be used at temperatures between -40 F (-40 C) and 140 F (60 C) having a rated working pressure of at least 350 psig (2.4 MPa) and a minimum burst pressure of five times the rated working pressure. CTA (Consumer Technology Association) Office: 1919 South Eads Street Arlington, VA Veronica Lancaster (703) vlancaster@cta.tech BSR/CTA x, Physical Activity Monitoring for Heart Rate and Related Measures (new standard) Stakeholders: Consumers, health and fitness device manufacturers and users. Project Need: To create definitions and performance criteria for consumer technology that measures heart rate or related parameters. This standard creates definitions and performance criteria for consumer technology that measures heart rate or related parameters. HL7 (Health Level Seven) Office: 3300 Washtenaw Avenue Suite 227 Ann Arbor, MI Karen Van Hentenryck (734) Karenvan@HL7.org BSR/HL7 V3 CPM CMET, R4-201x, HL7 Version 3 Standard: Common Product Model CMETs, Release 4 (revision and redesignation of ANSI/HL7 V3 CPM CMET, R3-2016) Stakeholders: Pharmaceutical, healthcare, government, FDA, EMA, CDISC, NCI, HL7, ISO, GS1. Project Need: Periodically, V3 DMIMs and RMIMs are updated to reflect new requirements, e.g., SPL, requiring updates to CPM to support their requirements. In the near term, SPL R8 and R9 are expected to have such requirements, while future SPLs or other areas may yield such requirements. This version updates CPM to support SPL Release 8 (which is forthcoming), including data elements for food and dietary supplements. BSR/HL7 V3 PASS AUDIT, R1-201x, HL7 Version 3 Standard: Privacy, Access and Security Services (PASS); Audit Services, Release 1 (new standard) Stakeholders: Standards Development Organizations (SDOs), Health Care IT Vendors, health information network providers. Project Need: This project is needed for the PASS project, which includes Audit, Authentication, and Authorization services. The Privacy, Access and Security Services (PASS) project specifies a set of Service Functional Models (SFMs), each of which defines an encapsulated, loosely coupled and composable service component that can contribute to ensuring the confidentiality and integrity of healthcare information within a service-oriented environment. The purpose of the PASS Healthcare Audit Services Conceptual Model specification is to provide the audit service interfaces associated with the security and privacy capabilities. ISA (International Society of Automation) Office: 67 Alexander Drive Research Triangle Park, NC Charles Robinson (919) crobinson@isa.org BSR/ISA x, Functional Safety: Safety Controls, Alarms, and Interlocks for the Process Sector (new standard) Stakeholders: End users and equipment/system suppliers throughout the process industries. Project Need: To advance functional safety practices in the process industries. This standard will establish a lifecycle for the design and management of safety controls, alarms, and interlocks and will define the requirements for the major phases of the lifecycle.

18 Standards Action - July 29, Page 18 of 38 Pages SCTE (Society of Cable Telecommunications Engineers) Office: 140 Philips Road Exton, PA Rebecca Yaletchko (610) ryaletchko@scte.org BSR/SCTE EMS x, Key Performance Metrics: Energy Efficiency and Functional Density of CMTS, CCAP, and Time Server Equipment (new standard) Stakeholders: Cable Telecommunication industry. Project Need: Create new standard. This document defines how to use a standard methodology to measure the density of hardware to meet the needs of optimizing critical space, as well as measuring energy consumption for the various network element classes. This part of the series focuses on the CMTS, CCAP, and other related cable-operator-critical facility equipment. BSR/SCTE EMS-004-a-201x, General Test Procedures for Evaluation of Energy Efficiency Metrics and in Support of Functional Density Metrics (new standard) Stakeholders: Cable Telecommunication industry. Project Need: Create new standard. This document covers the general test procedures that are common to all equipment types and specifies the environmental conditions for evaluating cable-equipment energy-efficiency metrics. Expectations of measurement equipment as well as guidelines on the recording of results are also covered. This standard will be included as a normative reference in each supplemental standard in the series covering metrics and specific test procedures for the various equipment types. SMACNA (Sheet Metal and Air-Conditioning Contractors' National Association) Office: 4201 Lafayette Center Drive Chantilly, VA Sue Baker (703) sbaker@smacna.org BSR/SMACNA x, Thermoset FRP Duct Construction Manual (new standard) Stakeholders: Designers, contractors, manufacturers, and code officials. Project Need: Fabrication and Installation for Fiberglass Reinforced Plastic (FRP) used in process/corrosive applications and commercial HVAC applications. The Thermoset FRP Duct Construction Manual is an authoritative manual that design engineers, industrial engineering departments, pollution control authorities, FRP manufacturers, and installation contractors can rely upon for the proper selection, manufacture, and installation of FRP duct systems. TAPPI (Technical Association of the Pulp and Paper Industry) Office: 15 Technology Parkway South Peachtree Corners, GA Laurence Womack (770) standards@tappi.org BSR/TAPPI T 834 om-201x, Determination of containerboard roll hardness (revision of ANSI/TAPPI T 834 om-2012) Stakeholders: Manufacturers of pulp, paper, packaging, or related products, consumers or converters of such products, and suppliers of equipment, supplies, or raw materials for the manufacture of such products. Project Need: To conduct required five-year review of an existing TAPPI/ANSI standard in order to revise it if needed to address new technology or correct errors. This test method describes a procedure to determine the uniformity in relative hardness of rolls of containerboard. Since several devices are currently available that use significantly differing technologies to determine hardness, this method only addresses the actual measurement process and not the test equipment specifically. UL (Underwriters Laboratories, Inc.) Office: 333 Pfingsten Road Northbrook, IL Megan Van Heirseele (847) Megan.M.VanHeirseele@ul.com BSR/UL X, Standard for Safety for Low-Voltage Switchgear and Controlgear - Controllers for Drivers of Stationary Fire Pumps (national adoption with modifications of IEC 62091) Stakeholders: Manufacturers of fire pump controllers and fire pumps, users of fire pumps, manufacturers of industrial control equipment and components, building owners and maintenance personnel, fire marshals, building inspectors, and other AHJs. Project Need: To obtain national recognition of an IEC-based standard covering low-voltage switchgear and controlgear controllers for drivers of stationary fire pumps. This standard applies to controllers intended for starting, controlling and stopping stationary fire pumps, including automatic and nonautomatic types for alternating-current electric-motor- or diesel-enginedriven fire pumps. It is anticipated that a controller only controls a single driver. Controllers for electric motor-driven fire pumps always include suitable short-circuit protection as an integral part of the controller. These controllers may include an integral power transfer switch. These controllers are rated 1000 Vac maximum. Controllers for diesel-engine-driven fire pumps include electrical circuits that operate various control and supervisory functions.

19 Standards Action - July 29, Page 19 of 38 Pages American National Standards Maintained Under Continuous Maintenance The ANSI Essential Requirements: Due Process Requirements for American National Standards provides two options for the maintenance of American National Standards (ANS): periodic maintenance (see clause 4.7.1) and continuous maintenance (see clause 4.7.2). Continuous maintenance is defined as follows: The standard shall be maintained by an accredited standards developer. A documented program for periodic publication of revisions shall be established by the standards developer. Processing of these revisions shall be in accordance with these procedures. The published standard shall include a clear statement of the intent to consider requests for change and information on the submittal of such requests. Procedures shall be established for timely, documented consensus action on each request for change and no portion of the standard shall be excluded from the revision process. In the event that no revisions are issued for a period of four years, action to reaffirm or withdraw the standard shall be taken in accordance with the procedures contained in the ANSI Essential Requirements. The Executive Standards Council (ExSC) has determined that for standards maintained under the Continuous Maintenance option, separate PINS announcements are not required. The following ANSI Accredited Standards Developers have formally registered standards under the Continuous Maintenance option. - AAMI (Association for the Advancement of Medical Instrumentation) - AAMVA (American Association of Motor Vehicle Administrators) - AGA (American Gas Association) - AGSC (Auto Glass Safety Council) - ASC X9 (Accredited Standards Committee X9, Incorporated) - ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.) - ASME (American Society of Mechanical Engineers) - ASTM (ASTM International) - GBI (The Green Building Initiative) - GEIA (Greenguard Environmental Institute) - HL7 (Health Level Seven) - IESNA (The Illuminating Engineering Society of North America) - MHI (ASC MH10) (Material Handling Industry) - NAHBRC (NAHB Research Center, Inc.) - NBBPVI (National Board of Boiler and Pressure Vessel Inspectors) - NCPDP (National Council for Prescription Drug Programs) - NISO (National Information Standards Organization) - NSF (NSF International) - PRCA (Professional Ropes Course Association) - RESNET (Residential Energy Services Network) - TIA (Telecommunications Industry Association) - UL (Underwriters Laboratories, Inc.) To obtain additional information with regard to these standards, including contact information at the ANSI Accredited Standards Developer, please visit ANSI Online at select Standards Activities, click on Public Review and Comment and American National Standards Maintained Under Continuous Maintenance. This information is also available directly at Alternatively, you may contact the Procedures & Standards Administration department (PSA) at psa@ansi.org or via fax at If you request that information be provided via , please include your address; if you request that information be provided via fax, please include your fax number. Thank you.

20 Standards Action - July 29, Page 20 of 38 Pages ANSI-Accredited Standards Developers Contact Information The addresses listed in this section are to be used in conjunction with standards listed in PINS, Call for Comment and Final Actions. This section is a list of developers who have submitted standards for this issue of Standards Action it is not intended to be a list of all ANSI-Accredited Standards Developers. Please send all address corrections to Standards Action Editor at standact@ansi.org. AAMI Association for the Advancement of Medical Instrumentation 4301 N Fairfax Drive Suite 301 Arlington, VA Phone: (703) (703) Web: ABYC American Boat and Yacht Council 613 Third Street, Suite 10 Annapolis, MD Phone: (410) Web: ADA (Organization) American Dental Association 211 E. Chicago Ave Chicago, IL Phone: (312) (312) Web: AHRI Air-Conditioning, Heating, and Refrigeration Institute 2111 Wilson Boulevard Suite 500 Arlington, VA Phone: (703) (703) Web: AISC American Institute of Steel Construction One East Wacker Drive Suite 700 Chicago, IL Phone: (312) (312) Web: ANS American Nuclear Society 555 North Kensington Avenue La Grange Park, IL Phone: (708) (708) Web: ARMA ARMA International College Boulevard Suite 450 Overland Park, KS Phone: (913) (913) Web: ASA (ASC S1) Acoustical Society of America 1305 Walt Whitman Road Suite 300 Melville, NY Phone: (631) (631) Web: ASA (ASC S12) Acoustical Society of America 1305 Walt Whitman Rd Suite 300 Melville, NY Phone: (631) (631) Web: ASABE American Society of Agricultural and Biological Engineers 2920 Niles Rd. St. Joseph, MI Phone: (269) Web: ASB (ASC Z50) American Society of Baking 243 Reade Drive Cogan Station, PA Phone: (570) (570) Web: ASHRAE American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc Tullie Circle, NE Atlanta, GA Phone: (678) (678) Web: ASME American Society of Mechanical Engineers Two Park Avenue New York, NY Phone: (212) (212) Web: ASSE (Safety) American Society of Safety Engineers 520 N. Northwest Highway Park Ridge, IL Phone: (847) (847) Web: ASTM ASTM International 100 Barr Harbor Drive West Conshohocken, PA Phone: (610) (610) Web: AWS American Welding Society 8669 NW 36th Street #130 Miami, FL Phone: (800) Web: AWWA American Water Works Association 6666 W. Quincy Ave. Denver, CO Phone: (303) (303) Web: CSA CSA Group 8501 East Pleasant Valley Rd. Cleveland, OH Phone: (216) x88321 (216) Web: CTA Consumer Technology Association 1919 South Eads Street Arlington, VA Phone: (703) (703) Web: HL7 Health Level Seven 3300 Washtenaw Avenue Suite 227 Ann Arbor, MI Phone: (734) (734) Web: ISA (Organization) International Society of Automation 67 Alexander Drive Research Triangle Park, NC Phone: (919) (919) Web: MHI Material Handling Industry 8720 Red Oak Blvd. - Ste. 201 Suite 201 Charlotte, NC Phone: (704) (704) Web: NEMA (ASC C78) National Electrical Manufacturers Association 1300 N 17th St Rosslyn, VA Phone: Web: NEMA (ASC C8) National Electrical Manufacturers Association 1300 North 17th Street Rosslyn, VA Phone: (703) Web: NEMA (ASC C82) National Electrical Manufacturers Association 1300 N 17th St Rosslyn, VA Phone: Web: NIST/ITL National Institute of Standards and Technology/Information Technology Laboratory 100 Bureau Drive Stop 8900 NIST Gaithersburg, MD Phone: Web: NSF NSF International 789 N. Dixboro Road Ann Arbor, MI Phone: (734) Web: RESNET Residential Energy Services Network, Inc Patina Court Oceanside, CA Phone: (760) (760) Web: SCTE Society of Cable Telecommunications Engineers 140 Philips Road Exton, PA Phone: (480) (610) Web: SMACNA Sheet Metal and Air-Conditioning Contractors' National Association 4201 Lafayette Center Drive Chantilly, VA Phone: (703) (703) Web:

21 Standards Action - July 29, Page 21 of 38 Pages TAPPI Technical Association of the Pulp and Paper Industry 15 Technology Parkway South Peachtree Corners, GA Phone: (770) (770) Web: TIA Telecommunications Industry Association 1320 North Courthouse Road Suite 200 Arlington, VA Phone: (703) (703) Web: UL Underwriters Laboratories, Inc. 333 Pfingsten Road Northbrook, IL Phone: (847) (847) Web:

22 Standards Action - July 29, Page 22 of 38 Pages ISO & IEC Draft International Standards This section lists proposed standards that the International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC) are considering for approval. The proposals have received substantial support within the technical committees or subcommittees that developed them and are now being circulated to ISO and IEC members for comment and vote. Standards Action readers interested in reviewing and commenting on these documents should order copies from ANSI. Comments Comments regarding ISO documents should be sent to ANSI s ISO Team (isot@ansi.org); those regarding IEC documents should be sent to Tony Zertuche, General Secretary, USNC/IEC, at ANSI's New York offices (tzertuche@ansi.org). The final date for offering comments is listed after each draft. Ordering Instructions ISO and IEC Drafts can be made available by contacting ANSI s Customer Service department. Please your request for an ISO or IEC Draft to Customer Service at sales@ansi.org. When making your request, please provide the date of the Standards Action issue in which the draft document you are requesting appears. ISO Standards AGRICULTURAL FOOD PRODUCTS (TC 34) ISO/DIS 8588, Sensory analysis - Methodology - A - not A test - 10/14/2016, $71.00 ANAESTHETIC AND RESPIRATORY EQUIPMENT (TC 121) ISO/DIS 20789, Anaesthetic and respiratory equipment - Passive humidifiers - 10/13/2016, $ CARBON DIOXIDE CAPTURE, TRANSPORTATION, AND GEOLOGICAL STORAGE (TC 265) ISO/DIS 27914, Carbon Dioxide Capture, Transportation and Geological Storage - Geological Storage - 8/13/2016, $ FLUID POWER SYSTEMS (TC 131) ISO/DIS 12669, Hydraulic fluid power - Method for determining the required cleanliness level (RCL) for a system - 10/12/2016, $71.00 IMPLANTS FOR SURGERY (TC 150) ISO /DAmd1, Implants for surgery - Wear of total hip-joint prostheses - Part 1: Loading and displacement parameters for weartesting machines and corresponding environmental conditions for test - Amendment 1-8/11/2016, $33.00 INTERNAL COMBUSTION ENGINES (TC 70) ISO/DIS , Reciprocating internal combustion engines - Exhaust emission measurement - Part 4: Steady-state and transient test cycles for different engine applications - 8/13/2016, $ MECHANICAL CONTRACEPTIVES (TC 157) ISO/DIS 16038, Male condoms - Guidance on the use of ISO 4074 and ISO in the quality management of natural rubber latex condoms and synthetic condoms - 12/8/2010, $67.00 NANOTECHNOLOGIES (TC 229) ISO/DIS 19007, Nanotechnologies - In vitro MTS assay for measuring the cytotoxic effect of nanoparticles - 8/10/2016, FREE NUCLEAR ENERGY (TC 85) ISO/ASTM DIS 51205, Practice for use of a ceric-cerous sulfate dosimetry system - 8/14/2016, $58.00 OPTICS AND OPTICAL INSTRUMENTS (TC 172) ISO/DIS 20711, Optics and photonics - Environmental requirements - Test requirements for telescopic systems - 8/14/2016, $53.00 PAINTS AND VARNISHES (TC 35) ISO/DIS , Paints and varnishes - Determination of resistance to humidity - Part 3: Condensation (in-cabinet exposure with heated, bubbling water reservoir) - 10/13/2016, $40.00 PLASTICS PIPES, FITTINGS AND VALVES FOR THE TRANSPORT OF FLUIDS (TC 138) ISO/DIS , Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 1: Butt fusion - 10/12/2016, $88.00 ROAD VEHICLES (TC 22) ISO/DIS , Road vehicles - Functional safety - Part 1: Vocabulary - 10/14/2016, $ ISO/DIS , Road vehicles - Functional safety - Part 2: Management of functional safety - 10/14/2016, $ ISO/DIS , Road vehicles - Functional safety - Part 3: Concept phase - 10/14/2016, $93.00 ISO/DIS , Road vehicles - Functional safety - Part 4: Product development at the system level - 10/14/2016, $ ISO/DIS , Road vehicles - Functional safety - Part 5: Product development at the hardware level - 10/14/2016, $ ISO/DIS , Road vehicles - Functional safety - Part 6: Product development at the software level - 10/14/2016, $ ISO/DIS , Road vehicles - Functional safety - Part 7: Production, operation, service and decommisssioning - 10/14/2016, $71.00 ISO/DIS , Road vehicles - Functional safety - Part 8: Supporting processes - 10/14/2016, $ ISO/DIS , Road vehicles - Functional safety - Part 9: Automotive safety integrity level (ASIL)-oriented and safety-oriented analyses - 10/14/2016, $93.00