Channel Safety Systems Limited Unit 9, Petersfield Business Park Bedford Road Petersfield GU32 3QA UK. Authority & date SMO /04/2014

Transcription

1 Test Report Report No Client Channel Safety Systems Limited Unit 9, Petersfield Business Park Bedford Road Petersfield GU32 3QA UK Authority & date SMO /04/2014 Items tested CDA/CO/1 - RESitech- Easy-fit base Carbon Monoxide-Mains inter-linkable c/w 1year battery CO Alarm Specification BS EN :2010+A1:2012 clause only (Electrical apparatus for the detection of carbon monoxide in domestic premises) only Results Samples of the above product have been tested and examined to the above specification with the conclusions as detailed in this test report. Prepared by Muntazir Momin Authorised by K Patel Issue Date 26 th June 2014 Conditions of issue This Test Report is issued subject to the conditions stated in current issue of CP0322 'Conditions of Contract for Testing'. The results contained herein apply only to the particular sample/s tested and to the specific tests carried out, as detailed in this Test Report. The issuing of this Test Report does not indicate any measure of Approval, Certification, Supervision, Control or Surveillance by BSI of any product. No extract, abridgement or abstraction from a Test Report may be published or used to advertise a product without the written consent of the Managing Director, Testing Services, who reserves the absolute right to agree or reject all or any of the details of any items or publicity for which consent may be sought. Opinions and interpretations expressed herein are outside the scope of UKAS accreditation BSI, Holywell Park, Loughborough, Leicestershire, LE11 3AQ Tel: , appliances@bsigroup.com Page: 1 of 6 ref: 06/10/

2 Blank Page Page: 2 of 6 ref: 06/10/

3 Test Sample Designation Sample No / /6 Description of Samples (Including Serial Number) CDA/CO/1 - RESitech- Easy-fit base Carbon Monoxide- Mains Alarms Description of Test Sample The unit is powered by mains and has a replaceable 9V PP3 back up battery. The unit also features interconnect function and has test and hush buttons on the top. The LED on top of the unit are to indicate alarm conditions, fault signal and low battery. Photos name/mod el no.: Front view Rear view Page: 3 of 6 ref: 06/10/

4 name/mod el no.: Internal view Page: 4 of 6 ref: 06/10/

5 Test Programme As supplied, the samples were tested to clause & of BS EN : 2010 (Electrical apparatus for the detection of carbon monoxide in domestic premises) only. No other clauses were tested/assessed on this occasion. Tests were carried out with the samples powered as per the manufacturer s instruction at 230V~ 50Hz in laboratory ambient conditions deg C and 35% - 50% rh Note: Clause Alarm Conditions of BS EN : 2010 refers to clause for test conditions Pre-conditioning was conducted on this occasion The following test conditions and criteria were considered during the test; Test conditions: Expose 3 samples to Test Gases A, B, C & D and all 3 units should pass and should recover within 6min when exposed to clean air Test Gases used & alarm conditions: Test Gas A (33ppm ± 3ppm) no alarm within 120min of exposure Test Gas B (55ppm ± 5ppm) no alarm before 60min but alarm before 90min of total exposure Test Gas C (110ppm ± 10ppm) no alarm before 10min but alarm before 40min of total exposure Test Gas D (330ppm ± 30ppm) alarm within 3min of exposure Samples were powered via 230V~ 50Hz variac with the 9V PP3 battery back-up present during testing. Clause Requirement Complies? General YES Alarm conditions Test Under the environmental conditions specified in to 5.2.8, test the alarm conditions as described in Performance requirement YES When exposed to CO - air mixtures, the alarm shall operate according to the conditions in Table 3. Recovery from the alarm state shall take place, after manual resetting if necessary, within 6 minutes when exposed to clean air. YES KEY TO TERMS USED IN REPORT YES - Complies. Tested by BSI engineers at BSI laboratories. YES1 - Complies. Witness tested by BSI engineers in manufacturer's laboratory. Not UKAS YES2 - Complies. Tests carried out by manufacturer; results accepted by BSI. Accredited N/A - Not applicable to design under consideration. NTx - Not tested due to similarity to previously tested item; reference earlier test report. NO - Non compliant. Page: 5 of 6 ref: 06/10/

6 Summary of Results: Clause Alarm conditions Clause Test methods and performance requirements (To set benchmark sample before the test) Test Conditions: Test Gas Test gas A (33ppm ± 3ppm) Actual CO level (ppm) 36ppm Alarm response (mins)? / Fail? /2 No Alarm /3 No Alarm /5 No Alarm Clean air for 15min N/A Test gas B (55ppm ± 5ppm) 54ppm / / /5 76 Clean air for 15min Within 6 Mins Test gas C (110ppm ± 10ppm) 115ppm / / /5 25 Clean air for 15min Within 6 Mins Test gas D (330ppm ± 30ppm) 334ppm /2 < /3 < /5 < 1 Clean air for 15min Within 6 Mins Pressure: mBar Humidity: 42% Temperature: 22 C Page: 6 of 6 ref: 06/10/