Malem Universal Wireless Alarm Model MO15
|
|
- Amber Ward
- 6 years ago
- Views:
Transcription
1 Malem Universal Wireless Alarm Model MO15 IMPORTANT Please read instruction booklet before use Instructions for use The alarm can be used for several applications or combinations: l Wander alarm l Continence alarm l Sit up alarm l Enuresis alarm l Sleepwalking alarm l Dialysis leakage alarm Up to seven clients can be monitored with one receiver Ideal for nursing/care homes, special schools, hospitals, institutions and individuals Helps to prevent bed sores and broken bones in Dementia, Alzheimer s, Memory Loss, the Elderly, People with Special Needs
2 Disclaimer Malem Universal Wireless Alarm is designed as a helpful and versatile aid. It is not intended to replace human care or supervision and the manufacturer, Malem Medical, is not responsible for any consequences resulting from the use, misuse or failure of this device.
3 Contents Instructions for Use Easy-Clip Sensor...2 Standard Sensor...3 Bed-Mat...4 Wander-Mat...6 Dialysis-Mat...7 Resetting Receiver (Rx) Sound...7 Channel Selection...8 Receiver LED Number Selection...8 Re-tuning (Pairing)...8 Sound Selection Switch...8 Batteries...9 Guarantee...9 Repairs...9 Cleaning...10 Disposal...10 Fault Finding...10 Specification Tx & Rx Diagrams Tx & Rx How to Connect Tx with Different Sensors The Inverter MM100111
4 WIRELESS ALARM TRANSMITTER MO15(Tx) Instructions for use 1. Switch on the receiver (Rx) unit. Green LED will flash once every two seconds. See page Remove insulator from battery compartment (if present) of the transmitter (Tx) unit. See page Plug the sensor of choice into the transmitter (Tx) unit. See pages 17 & If used with Easy-Clip Sensor (EC): i) Make sure the Easy-Clip Sensor lever is in the up position. (Lowering the lever without placing material between the front jaws will activate the transmitter and trigger the receiver buzzer). If buzzer does not sound, retune Tx & Rx as per instructions. See page 8. ii) Using the safety pin, attach the Tx to the pyjama top or nightdress close to the shoulder. Attach Tx to material before wearing garment if preferable. Carefully lock the safety pin. Do not use safety pin if faulty. Optional shoulder clip is available for clinics on request if safety pin use is unsuitable. iii) Thread sensor lead inside top as shown in diagram above. For small children, loop and tie sensor lead to shorten length. iv) Attach sensor clip to the outside of close fitting underwear (at the location where it is most likely to get wet first), by inserting the folded underpants material inside the front jaw of the clip then lowering the lever. (Lowering the lever without any dry material in the jaws will activate the Tx, trigger the Rx alarm and prevent the Rx from being reset). Lift the lever and press the reset button. Do not reset the Rx by switching off. Always use the reset button. MALEM UNIVERSAL Lock the Easy-Clip onto the material by pressing down the lever IMPORTANT: DO NOT PLACE ANY MATERIAL UNDER THE SECURING LEVER Place underwear material into mouth (jaws) at the front of the Easy-Clip 2 IMPORTANT: Regularly CLEAN Easy-Clip Sensor in soapy water, rinse and shake dry
5 5. If used with Standard Sensor (BT): a) Absorbent pad: i) Cut off one end of an absorbent pad such as sanitary or incontinence pad and insert the sensor in between the layers. ii) Anchor with crocodile clip to prevent sensor from being pulled out. Uncover the backing strip and stick Please note that sensor and clip the pad inside a pair of close fitting are gold plated pants, ensuring the sensor is located where it will come into contact with the flow of urine. b) Between two pairs of underpants: i) Sandwich between two pairs of cotton briefs (not boxer shorts). Anchor with crocodile clip. c) Within Y-front fold: i) Place sensor plate within Y-fronts fold and anchor by locating the crocodile clip on the outside of the waistband of the pants. Avoid nylon/polyester underwear. d) With pull-ups or nappies: i) Cut a small slit into the outside of the material and insert the sensor plate at a location close to the urine flow. Outer Pants Inner Pant Please make sure the sensor plate and the crocodile clip are attached between the two pairs of pants and MUST NOT come in contact with the skin 3
6 6. If used with Bed-Mat Sensor (BM): a) Under no circumstances should the transmitter (Tx) be attached to the users clothing when using a Bed-Mat. b) Place a clean and dry Bed-Mat correct side up over the mattress in the area which is normally wetted and gently tie down. See page 5. c) Cover the Bed-Mat with a Clean Dry Cotton sheet and/or Bath Towel and make the bed up as usual. Avoid nylon/polyester sheets as they can cause false alarms due to increased perspiration. Adjust cover thickness over the mat to suit. d) Do not place plastic sheets directly under the Bed-Mat as condensation will cause the alarm to trigger. (See diagram page 5) e) Attach the Bed-Mat wire to the Tx and place the Tx beside the bed. See page 17. f) Please tuck in the Bed-Mat wire so that it is not in the way for getting in and out of bed. g) Upon waking to the Rx, try to stop any more urine from being released and use the lavatory to completely empty the bladder. h) The Rx alarm sound can be stopped ONLY when the Bed-Mat wire is unlocked from the Tx and the reset button on the Rx is pressed. i) For reuse, the Bed-Mat must be wiped clean with detergent and dried then replaced in a freshly made bed, as before. j) To test the system, place a damp cloth across the foil tracks on the Bed-Mat. 4
7 WIRELESS ALARM TRANSMITTER MO15(Tx) Under NO circumstances should the transmitter (Tx) be attached to the users clothing when using a Bed-Mat. MALEM UNIVERSAL Holes for tying Bed-Mat to the mattress. If using a plastic protective mattress sheet place adhesive tape over the Bed-Mat lower contacts. Bath Towel Sheet Bed-Mat Mattress Use a BATH TOWEL to cover the Bed-Mat and cotton sheet. Adjust towel thickness to suit. Pillow Transmitter (Tx) Place cotton sheet over Bed-Mat. Tie Bed-Mat around mattress. Tuck wire from Bed-Mat to alarm away neatly to prevent tripping or entanglement. 5 Bedside table
8 Hints regarding the use of Bed-Mat: l l l l l l l l Press the reset button once, receiver alarm sound will stop. LED will continue to flash. If the Bed-Mat is not dried or disconnected, the alarm sound will start again within two minutes. Press and hold the reset button for two seconds to stop the alarm and turn off the LED. The Bed-Mat positively locks to the Tx to prevent accidental disconnection. However, it must be unlocked before attempting to reset the alarm. Please use a thicker cotton sheet or place a bath towel above the Bed-Mat if sweating is triggering the Tx prematurely. Avoid plastic and man-made fibres as they may cause static discharge and false alarm. Treat the Bed-Mat with care. Avoid folding it or jumping on it. Please replace the Bed-Mat with a new one if it has deteriorated and use a new one with each user. (National Guidelines) Please note that sleeping directly on an uncovered Bed-Mat or touching it by hand may trigger the Tx and sound the alarm. Do not place plastic sheets directly under the Bed-Mat as condensation may trigger the alarm. 7. If used with Wander-Mat Sensor (WM): a) Activation by applied pressure: place the Wander-Mat (WM) in the appropriate position depending on the way you wish to use it. The Wander-Mat can be placed beside the bed or near the door so that treading on the Mat will activate the Tx. Please place a door mat over the Wander-Mat so as not to trip over the Wander-Mat. Plug into the Tx and place away safely. See page 19. b) Activation by removal of pressure: place the Wander-Mat (WM) over the mattress but under the sheet, in a position so that the user is laying over it or place on a chair so that the user is sitting on it. Plug the Wander-Mat wire into the inverter then plug the inverter wire into the Tx and place Tx away safely. If the user gets out of bed or out of the chair, the Tx will be activated triggering the Rx sound and selected LED. c) Once the receiver (Rx) is triggered, the appropriate red LED will be flashing. The buzzer sound can be silenced by pressing the reset button on the top of the Rx. (Do not use the on/off switch to reset the Rx as this will damage the microprocessor). The activated LED will remain flashing. If the matched Tx remains active, the Rx will sound again after two minutes. Press and hold for 3 seconds to deactivate and switch LED off. 6
9 8. If used with Dialysis-Mat Sensor (DM): a) Select the correct side of the Mat with shiny tracks up. b) Place the Mat over the chair arm. c) Plug the Mat wire into the Transmitter, tuck the wire and place Tx out of the way in a safe place. See page 18. d) Test the Mat by placing a slightly wet tissue over the tracks. The Rx should sound. e) If sweating is likely to activate Tx and sound the alarm cover the Mat surface with tissue paper. Adjust thickness to suit. f) Rest patients arm over the Mat. g) Wipe Mat clean and dry before use again. 9. Deactivating the Transmitter: a) If using the Easy-Clip sensor, lift the sensor lever and remove from underpants (wash Easy-Clip sensor frequently). b) If using the Standard sensor, unclip the crocodile clip and remove the sensor, wipe sensor plate dry and clean regularly. c) If using the Bed-Mat, unplug the Bed-Mat from the Tx, remove the sheet, wipe clean and dry thoroughly before repositioning. d) If using the pressure/release Wander-Mat, unplug from the Tx and reposition the user on the Mat. c) If using the Dialysis-Mat, unplug from the Tx, clean and dry the Mat then, reposition. f) Press the reset button on the Rx to silence the buzzer. 10. Resetting the Rx Sound: a) Press and hold the reset button for 2 seconds to switch off the sound and de-activated LED/s (make sure matched Tx is not active). b) The matched Tx/Rx will not trigger the Rx if the Tx is activated within 2 minutes of previous activation. c) For easy identification, an adhesive label can be used on the front of the Rx where you can write the room number or occupant name for each of the seven LEDs. 7
10 Channel Selection see diagram on page 14 The Malem Universal ON Wireless Alarm consists of a receiver which can be paired with up to seven transmitters. To avoid interference OFF from the 7 transmitters or other wireless equipment, you need to select different channel settings for each of the transmitters. A choice of 64 settings is possible and should be changed in case of interference. To change the channel setting, remove the back of the transmitter using a slotted screwdriver. Lower to open. Change the setting of the code selection switch (the one on the left) by moving any of the switches in any of the 64 combinations. Receiver LED Number Selection see diagram on page 14 To match a Tx with a specific Rx LED number, remove the battery cover of the Tx using a slotted screwdriver. The LED selection switch is the one on the right. Select the LED number by sliding the matching number (between 1 and 7) of the sliding switch to ON. Re-tune Tx and Rx. See below. Re-tuning the Rx and Tx see diagram on page 14 & 16 ON All additional transmitters will need to be re-tuned with the Rx. a) Select the desired Rx LED number first (see above) OFF b) Push and release the straight end of a paper clip into the small LEFT hole at the back of the receiver. All the 7 LED s will glow. c) Immediately and while the LED s are glowing, activate the Tx you wish to tune/re-tune by lowering the Easy-Clip sensor lever or wetting the standard sensor or Bed-Mat or applying pressure on the Wander-Mat or wetting the Dialysis-Mat. d) The LED s will switch off apart from the selected one which will glow on and off. The next activation of the Tx will activate the Rx LED and the buzzer. e) Repeat for all other additional transmitters. f) Remember to change channel if you are experiencing any interference from other transmitters or wireless equipment. You can also tune several receivers to the same transmitters. This is helpful if more than one carer wants to monitor the transmitters. Sound Selection Switch see diagram on page 16 The receiver is factory set to 8 random sounds. For single sound selection: a) Open the Rx battery cover using a slotted screwdriver. Insert blade into slot and twist. b) Slide to ON any one of the switches between 1 and 8. c) Slide all other switches apart from 10 to the OFF position. d) Do not slide switch 10 to OFF as this will silence the Rx sound. 8
11 Important l Remove batteries from both Tx and Rx if not in use. l Observe clean battery compartment contacts and correct polarity when changing batteries. l Use long life alkaline batteries whenever possible. l Batteries should not be accessed by children and only replaced by adults. l Do not immerse the Tx or Rx in water. l Regularly clean the sensor in use. See page 10. l Do not leave the Tx active (LED on) as this will drain the battery. See page 13. l Do not use the receiver ON/OFF sliding switch as a reset button as this will damage the microprocessor. Always use the Reset button. Batteries (remove isolating tag if present) Batteries have been provided free of charge with original purchase to enable testing during manufacture and prior to packaging. Additional batteries can be purchased. Batteries should not be accessed by children and only replaced by adults. Use long life alkaline batteries whenever possible. Do not leave Tx active when not in use as this will drain the battery. Observe correct polarity and clean contacts when replacing Tx and Rx batteries. Tx: alkaline 23A 12V Rx: alkaline 3 x AA Replace batteries on the Tx or Rx if the LEDs are rapidly flashing. Safety pin Pull white cover slightly to unlock, push to lock, you can replace the safety pin by sliding the replacement bar to the left. See page 14. Guarantee Under normal usage, the Malem Universal Wireless Alarm is guaranteed for a period of three months from purchase. This excludes batteries, sensors, Bed-Mat, Wander-Mat, Dialysis-Mat, safety pin, flooding, misuse or accidental damage. If the alarm should malfunction during this period, please contact us before sending. Please remove the batteries and decontaminate the unit/s sensor before returning. Do not return flooded or contaminated alarms. Repairs If repairs are required, we will exchange for a new alarm (repairs are not untaken for health and hygiene reasons). Please contact us by telephone, or in writing for the cost of this service. Please decontaminate the units/s before return. Do not return contaminated or flooded alarms. 9
12 Cleaning Alarm units (Tx and Rx): Wipe clean alarm and safety pin using a damp cloth and mild detergent or skin disinfectant. NEVER IMMERSE IN WATER Sensors (wash regularly): Easy-Clip - lift lever, wash in warm soapy water, rinse under the tap and shake dry. Standard Sensor - wash in soapy water and dry thoroughly. Bed-Mat - wash in warm soapy water and wipe dry. Wander-Mat - wipe with damp cloth and mild detergent, dry thoroughly. Dialysis-Mat - wipe with damp cloth and mild detergent, dry thoroughly. National guidelines state one user per Sensor/Mat. Disposal At the end of the alarms working life, please dispose of the product at a special local authority differentiated waste collection centre. Fault Finding Alarm does not sound: a) Switch on receiver Rx. Green LED should flash. b) Replace batteries with new alkaline ones (3 x AA). Observe correct polarity orientation and make sure contacts inside the battery compartment are clean and free of any deposits. c) Sound selection switch has been wrongly set or switch No.10 has been set to OFF. Reset all switches to their original position as per diagram on page 16. d) Remember that the Rx will not sound again within 2 minutes of being activated by the Tx. However the Rx will be activated if other Tx is activated. The 2 minute delay is to allow the triggered Tx to be reset. If the Tx is not reset, then the Rx will sound again after 2 minutes if the reset button has been pressed to silence the buzzer. e) Does the Tx LED glow when the Tx is activated by lowering the lever on the Easy-Clip sensor or wetting the standard sensor or Bed- Mat/Dialysis-Mat or applying pressure on the Wander-Mat? If it does not glow, then replace the Tx battery (alkaline 23 A 12V). Observe correct polarity and clean contacts. f) Remove isolating tags from battery compartment in Tx and Rx. Retune Tx and Rx. If all fails, return Tx and Rx for investigation. Contact us before doing so. Decontaminate all units before returning. See diagram on pages 13 and
13 Alarm does not reset: a) Clean Easy-Clip sensor by lifting lever, wash in warm soapy water, rinse under the tap and shake dry. Repeat if necessary. b) Make sure Easy-Clip sensor lever is NOT down without dry material between the front jaws. c) Clean Bed-Mat and dry thoroughly. Use thicker towel over Mat. Do not use man made sheets over the Mat. d) Clean Dialysis-Mat and dry thoroughly. Use thicker tissue paper or material under the arm. e) Remove pressure or apply pressure to Wander-Mat. f) Make sure underpants material is not too thin or wet. g) Replace Tx and/or Rx batteries. h) Transmitter is damaged or flooded. Sound level is too low: a) Adjust sound level with volume control. See diagram on page 15. LED flashing rapidly: a) Replace battery. Specifications MO15 Transmitter (Tx) Colour: red Weight: 33g including battery, 25g without battery Dimensions: length: 50mm width: 45mm depth: 21mm Range: approximately 25m depending on nature of the structure and the state of the battery. Battery cover: to remove, place a slotted screwdriver in the bottom slot and lower the handle. Battery: alkaline 23 A. Observe correct polarity when replacing and ensure no deposits are on the metal contacts. Safety pin: pull white cover slightly to unlock, push to lock, you can replace the safety pin by sliding the replacement bar to the left. Do not use faulty safety pin. Red LED: flashes when transmitter is active. Do not leave on for extended length of time as this will drain the battery. LED will flash rapidly for 3 minutes and then turn off when battery capacity is low. Replace battery. Frequency: 433 MHz Model: MO15 Tx Standards: and 11
14 Specifications MO15 Receiver (Rx) Colour: red Weight: 136g including batteries, 67g without batteries Dimensions: length: 91mm width: 72mm depth: 26mm Battery: 3 x AA alkaline. Observe correct polarity and clean contacts when replacing batteries. ON/OFF: sliding switch on side Volume: volume control wheel on the side. Turn up to increase and down to decrease. Reset button on the top will not reset if Tx is active. Press button and hold for 3 seconds to cancel active LED. Do not use ON/OFF button to reset the receiver. Green LED: flashes once every 2 seconds when Rx is ready for use. Red LED 1 to 7: ON when paired Tx is triggered. Up to 7 Txs can be tuned and paired to the 7 LEDs. Once an LED is activated, even paired ON, when reset, it will not be triggered again for 2 minutes. The LED and buzzer will be reactivated if the linked Tx remains active. Tuning point: 2 small pin holes on the back of the Rx. The one on the left is the tuning hole. Insert the straight end of a paper clip into the hole and press slightly then release, all the red LEDs will glow. While the red LEDs are on, activate the Tx. The LEDs will go off and only the LED which has been selected on the Tx will flash. When the Tx is activated again, the LED will flash and the buzzer will sound. Green LED will flash rapidly when battery capacity is low. Replace battery. Default hole: the small hole on the right on the back of the Rx is the default hole. Insert the straightened end of a paper clip and press gently then release. This will erase all the tuned memory. Re-tuning to the Tx/s will be required. Model: MO15 (Rx) Standard: and Sensors Easy-Clip : Length 79 cm. Keep lever up when not in use. Clean sensor regularly. Standard: Length 79 cm. Keep clean and wipe dry. The sensor plate and crocodile clip MUST NOT be in direct contact with the skin. Bed-Mat: 54 x 42 cm. Wire length 202 cm. Keep clean and wipe dry. Always cover with cotton sheet as well as a bath towel. Under no circumstances should the transmitter (Tx) be attached to user s clothing when used with a Bed-Mat. Wander-Mat: 75 x 40 cm. Wire 150 cm. Use pressure on or pressure off (for pressure off use with inverter ). Dialysis-Mat: 22 x 17 cm. Wire 100 cm. Keep clean and wipe dry. Malem Medical reserves the right to change specifications without prior notice Malem Medical 12
15 Malem Universal Wireless Alarm Transmitter MODEL MO15 (Tx) Red LED flashes when Tx is active. Please do not leave on as this will drain the battery. If using the Easy-Clip sensor, please make sure the lever is up when not in use or unplug the sensor from the socket. MALEM UNIVERSAL WIRELESS ALARM TRANSMITTER MO15 (Tx) Sensor locking socket LED will flash rapidly for 3 minutes then turn off when the battery capacity is low. Replace battery. Use Alkaline batteries ONLY 13
16 Malem Universal Wireless Alarm Transmitter MODEL MO15 (Tx) ON ON OFF Channel selection switch Safety pin replacement bar ON OFF Receiver LED selection switch OPEN ON lock + 23A 12V ALKALINE - CHANNEL SELECTION SWITCH unlock Rx LED No. SELECTION SWITCH 23A 12V + - ALKALINE Safety pin slide cover sideways to lock or unlock Battery compartment To open place slotted screwdriver in slot and move handle down Use 1 x 23A 12V Alkaline batteries Please observe correct polarity when replacing batteries Sensor locking socket MODEL MO15(Tx) OPEN Use Alkaline batteries ONLY 14
17 Malem Universal Wireless Alarm Receiver MODEL MO15 (Rx) Mute/reset Buzzer Red LEDs 1-7 Each light corresponds to the transmitter it is paired with. MUTE / RESET BUZZER PRESS & HOLD FOR 3 SEC TO RESET Green standby LED/2 sec flashes. LED will flash rapidly when battery capacity is low. (Replace battery) Press and hold for 3 sec to reset Volume STANDBY LED/2 SEC OFF ON POWER MALEM - + VOLUME UNIVERSAL WIRELESS ALARM RECEIVER (Rx) Attach a label to the front of the Rx to indicate LED number, room number or users name. Power OFF - ON. Please do not use on/off switch to reset alarm. This will damage the microprocessor. Use reset button. Use Alkaline batteries ONLY 15
18 ON ON Malem Universal Wireless Alarm Receiver OFF Tx Rx Pairing. Use end of paper clip. Pass into hole, press and release, all red LEDs On, activate required Tx while red LEDs are On, one of the LEDs will flash the same number as the switch number selected on Tx. Sound selection switch Switch 1-8 will select sounds 1-8. Switch 9 must be off for single sound. For 8 sounds switch 1 as well as 9 and 10 must be On. Sounds will be Off if switch 10 is in the Off position. MODEL MO15 (Rx) Tx Rx Pairing To reset and erase all pairing memory use paper clip. Insert the end of a paper clip into the hole. Only use default to erase all pairing memory. Press and hold for 3 seconds. All pairing with Tx will be lost. To open battery compartment place slotted screwdriver in the slot then twist. Tx Rx PAIRING DEFAULT AA ALKALINE SOUND SELECTION SWITCHES AA ALKALINE SEE INSTRUCTIONS FOR USE AA ALKALINE - USE 3 x AA + ALKALINE BATTERY OPEN USE 3 x AA ALKALINE BATTERY USE 3 x AA + ALKALINE BATTERY Batteries: 3 x AA Please use alkaline. Observe correct polarity. Make sure metal contacts are clean. Use Alkaline batteries ONLY 16
19 Activation of the Tx using different sensors 1. Activation by Easy-Clip Sensor or Standard Sensor Malem Transmitter (Tx) Standard Sensor (BT) MALEM UNIVERSAL WIRELESS ALARM TRANSMITTER MO15 (Tx) Plug sensor into Tx socket Easy-Clip Sensor (EC) Lever - Keep up when not in use. Clean clip regulary. RJ10 plug 2. Activation using a Bed-Mat: 54 cm 42 cm 202 cm Malem Transmitter (Tx) RJ10 plug MALEM UNIVERSAL WIRELESS ALARM TRANSMITTER MO15 (Tx) Bed-Mat (BM) Bed-Mat connection wire Plug Bed-Mat RJ10 plug into the Malem transmitter socket 17
20 3. Activation using a Dialysis-Mat Malem Transmitter (Tx) 22 cm RJ10 plug MALEM UNIVERSAL WIRELESS ALARM TRANSMITTER MO15 (Tx) 17 cm Dialysis-Mat (DM) DM connection wire 100 cm Plug Dialysis Mat RJ10 plug into the Malem transmitter socket 18
21 Wander-Mat with inverter 4. Activation by applying pressure: 75 cm Malem Transmitter (Tx) 40 cm WANDER MAT RJ10 plug MALEM UNIVERSAL WIRELESS ALARM TRANSMITTER MO15 (Tx) Wander-Mat (WM) WM connection wire 150 cm Plug WM plug into Tx socket 5. Activation by removing pressure: (user must be lying in bed or sitting over WM in a chair) Malem Transmitter (Tx) WANDER MAT Wander-Mat (WM) RJ10 plug WM connection wire PM Inverter PRESSURE MAT INVERTOR MALEM Plug WM into inverter socket WM inverter wire MALEM UNIVERSAL WIRELESS ALARM TRANSMITTER MO15 (Tx) Plug inverter plug into Tx socket Please note that pressure must be applied to the Mat BEFORE attempting to set up the connection. 19
22 Malem Wander-Mat Inverter front: LED light MALEM WANDER MAT INVERTOR The RJ10 plugs into the transmitter (Tx) Battery test button The RJ10 Wander-Mat (WM) plug, plugs into the inverter socket Please plug in the inverter wire between the Wander-Mat and the transmitter. Battery test: press the button, LED will glow. If LED does not glow then change the battery. (Remove battery isolator if present) The inverter should be used ONLY if you wish to use the Wander-Mat to detect removal of pressure. Please do not immerse inverter or Mat in water. Use Alkaline batteries ONLY 20
23 Malem Wander-Mat Invertor back: Use slotted screwdriver to open. Place tip in slot and twist. RJ10 plug Battery test button 23A 12V + - ALKALINE RJ10 socket Please observe correct polarity. Contacts clean and battery not loose inside compartment. Pull metal contact to make good connection. Use only 23A 12V Alkaline battery. Use Alkaline batteries ONLY 21
24 FCC ID: U9FMO15 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: Changes or Modifications not expressly approved by the party responsible could void the user s authority to operate this device. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/tv technician for help. Malem Medical, 10 Willow Holt, Lowdham Nottingham NG14 7EJ, England, UK Tel: + 44 (0) Fax: + 44 (0) malem@malem.co.uk Web: Web: Malem Medical 2011
Malem MO7 Wireless Alarm + Record Wetness Sensor and Toilet Trainer
Malem MO7 Wireless Alarm + Record Wetness Sensor and Toilet Trainer Wireless 6 Channels 4MHz Please read the instructions carefully before use. For best results and trouble free operation, all instructions
More informationMalem Enuresis Alarms Instruction Booklet
Master IBooklet 101115_Master IBooklet 150512 23/11/2015 13:26 Page 1 Malem Enuresis Alarms Instruction Booklet IMPORTANT Please read instruction booklet before use Best Results are obtained when: 1. Child
More informationP163BBA Radio Enuresis Alarm Monitor
P163BBA Radio Enuresis Alarm Monitor Handbook P163BBA Models covered by this handbook Radio Comf-it Monitor One of a range of Alert-it Care Alarms available from: UH1249A Alert-it Care Alarms, Atherstone
More informationBBQ THERMOMETER DESCRIPTION OF PARTS. MODEL NO.: AW129/AWR129 Instruction Manual
BBQ THERMOMETER MODEL NO.: AW129/AWR129 Instruction Manual DESCRIPTION OF PARTS A. POWER BUTTON Turns the unit on/off. Press and hold for 2 seconds to activate unit. B. SELECT BUTTON Selects the type of
More informationWireless Home Appliance Timer Remote Control Kit
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. NOTE : This equipment has been tested
More informationREAD ME FIRST DIY WIRELESS ALERT. Gate Alert Kit. Instruction Manual
READ ME FIRST DIY WIRELESS ALERT Gate Alert Kit EN Instruction Manual AT A GLANCE Thank you for choosing the Gate Alert Kit from Swann. It's the ideal system to detect unwanted access into a restricted
More informationP163BBA Wired Enuresis Alarm Monitor
P163BBA Wired Enuresis Alarm Monitor Handbook P163BBB Models covered by this handbook Wired Comf-iT Monitor One of a range of Alert-it Care Alarms available from: UH1249B Alert-it Care Alarms, Atherstone
More informationHome Doorway Alert Kit
READ ME FIRST DIY WIRELESS ALERT Home Doorway Alert Kit EN Instruction Manual 2 About this Manual The content in this manual is for information purposes only and is subject to change without notice. While
More informationREAD ME FIRST DIY WIRELESS ALERT. Driveway Alert Kit. Instruction Manual
READ ME FIRST DIY WIRELESS ALERT Driveway Alert Kit EN Instruction Manual 2 About this Manual The content in this manual is for information purposes only and is subject to change without notice. While
More informationIMPORTANT SAFETY INSTRUCTIONS
WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK
More informationIMPORTANT SAFETY INFORMATION! WARNING ALWAYS keep electric cords, home furnishings, drapes, clothing, papers, or other combustibles at least 3 feet (0
Electric Fireplace Factory Model: EF-30D CONSUMER SAFETY INFORMATION Read this manual before installing and operating this appliance Failure to follow these instructions may result in electric shock, fire
More information1126 Series Ceiling Mount PIR Motion Detector
Installation Sheet 1126 Series Ceiling Mount PIR Motion Detector Description The 1126 Series PIR (Passive Infrared) Motion Detectors are a compact wireless PIR. The 1126 Series offer 360, Wide Angle, or
More information5-channel radio alarm for the treatment of bedwetting and for use for incontinence. Instructions for use
5-channel radio alarm for the treatment of bedwetting and for use for incontinence Instructions for use 2 E Alarm device for the treatment of bedwetting Description: The new is a wireless radio alarm for
More informationWS-9117U-IT Wireless 915 MHz Temperature Station. Instruction Manual
WS-9117U-IT Wireless 915 MHz Temperature Station Instruction Manual 1 TABLE OF CONTENTS Topic Inventory of Contents Quick Setup Detailed Setup Guide Battery Installation Setting the Time Features Minimum
More informationPRODUCT DIAGRAM PACKAGE CONTENTS
PRODUCT DIAGRAM PACKAGE CONTENTS After receiving the product, please inventory the contents to ensure you have all the proper parts, as listed below. If anything is missing or damaged, please contact Monoprice
More informationPRODUCT DIAGRAM PACKAGE CONTENTS
PRODUCT DIAGRAM PACKAGE CONTENTS After receiving the product, please inventory the contents to ensure you have all the proper parts, as listed below. If anything is missing or damaged, please contact Monoprice
More informationRGR150 USER S MANUAL. Wireless Rain Gauge with Thermometer and Clock
RGR150 manual-final-091908:layout 1 9/19/08 8:59 AM Page 1 RGR150 USER S MANUAL Wireless Rain Gauge with Thermometer and Clock INTRODUCTION Thank you for selecting this Wireless Rain Gauge. This device
More informationATOMIC DIGITAL CLOCK. Time and Alarm
Model: 515-1316 Instruction Manual DC: 052015 ATOMIC DIGITAL CLOCK Time and Alarm Month, Date, & Weekday Buttons 3 C Batteries Model: 515-1316 www.lacrossetechnology.com/support Page 1 Get Started Step
More informationAmbient Weather RC-9362 Atomic Digital Wall Clock with Temperature User Manual
Ambient Weather RC-9362 Atomic Digital Wall Clock with Temperature User Manual Table of Contents 1. Introduction... 1 2. Getting Started... 2 2.1 Product and Display Features... 2 2.2 Parts List... 2 2.3
More informationUltrasonic Aromatherapy Diffuser with Color Changing LED Lights Instruction Manual and Warranty Information - Read and Save These Instructions.
RevitaSpa Ultrasonic Aromatherapy Diffuser with Color Changing LED Lights Instruction Manual and Warranty Information - Read and Save These Instructions. Contents Safety Instructions...1 How It Works /
More informationREAD ME FIRST DIY WIRELESS ALERT. Add-on Alert Sensor. For Swann Wireless Alert systems. Instruction Manual
READ ME FIRST DIY WIRELESS ALERT Add-on Alert Sensor For Swann Wireless Alert systems EN Instruction Manual 2 About this Manual The content in this manual is for information purposes only and is subject
More informationPlease Keep This Manual For Future Reference REV.01
ELCG347 ELCG240 1-855-571-1044 Please Keep This Manual For Future Reference REV.01 IMPORTANT INFORMATION When using electrical appliances, basic precautions should always be followed to reduce the risk
More information1125 PIR Motion Detector
Tamper Survey LED INSTALLATION SHEET 1125 PIR Motion Detector Description The 1125 PIR (Passive Infrared) Motion Detector is a wireless, low current sensor for use with the 1100D Wireless Receiver. Using
More informationSOOTHING COOL MIST AROMA DIFFUSER
SOOTHING COOL MIST AROMA DIFFUSER FOR MODEL: EE-8003 If you have any questions about the operation of your aroma diffuser, please contact Crane Customer Care. Toll Free: 888-599-0992 Email: customer-service@crane-usa.com
More informationColor-Changing LED Aromatherapy Diffuser
Color-Changing LED Aromatherapy Diffuser Instruction Manual and Warranty Information - Read and Save These Instructions. Contents Safety Instructions...1 How It Works / Specifications...2 Parts & Contents...
More informationInstaller Guide smart connect
Installer Guide smart connect TM 7390 Wireless Remote Indoor Sensor Please read all instructions before proceeding. The wireless remote indoor sensor monitors temperature at a remote indoor location and
More informationHoneywell Temperature & Humidity Sensor with LCD
Honeywell Temperature & Humidity Sensor with LCD TABLE OF CONTENTS INTRODUCTION 3 PRODUCT OVERVIEW 4 BEFORE YOU BEGIN 5 BATTERY INSTALLATION 7 LOW BATTERY WARNING 7 PLACEMENT OF THE REMOTE SENSOR 7 GETTING
More information23-IN Electric Logset
23-IN Electric Logset ASSEMBLY, CARE & USE INSTRUCTIONS MODEL # ELCG240-INF Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-855-571-1044
More informationINSTRUCTIONS FOR. Wireless Refrigerator Freezer Thermometer (#10378)
CONTENTS Unpacking Instructions... 2 Package Contents... 2 Product Registration... 2 Features & Benefits: Sensors... 2 Features & Benefits: Display... 3 Setup... 4 Install or Replace Batteries... 4 Temperature
More informationMODEL MR-720 FUNCTIONS AND CONTROLS SELF-POWERED AM/FM WEATHER BAND CLOCK RADIO
FUNCTIONS AND CONTROLS MODEL MR-720 SELF-POWERED AM/FM WEATHER BAND CLOCK RADIO Please read this Instruction Manual carefully before using the unit and retain it for future reference 1. BAND SELECT SWITCH
More informationHomeowner s Installation Instructions & Operating Manual
Homeowner s Installation Instructions & Operating Manual ELECTRIC HEATER WITH REMOTE CONTROL Model: GI-32-ZC IS-36-ZC, IS-42-ZC Insert surrounds READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING
More informationCampers Alert TM Portable System Hunters Alert TM Portable System
Campers Alert TM Portable System Hunters Alert TM Portable System USER MANUAL READ THIS ENTIRE MANUAL PRIOR TO INSTALLATION AND OPERATION We thank you for purchasing this Driveway Alert System. All our
More informationExternal Wireless Sounder
External Wireless Sounder WL S50 Installation and Programming Instructions 2 Wireless Sounder Instructions Table of Contents Introduction... 4 Operational Functions... 4 Alarm / Tamper Indication...4 Low
More informationThank you for choosing Ideal Security s Home Security System with Telephone Dialer.
SK618 WIRELESS ALARM SYSTEM WITH AUTO DIALER OWNER'S MANUAL Thank you for choosing Ideal Security s Home Security System with Telephone Dialer. If at any time during your installation you have any questions
More informationProjection Alarm Clock
Projection Alarm Clock Model: W8923v2 Instructional Manual DC: 0676 For online video support visit: http://bit.ly/laxtechtalk Table of Contents LCD Features... Buttons... Setup... Set Time, Date, etc....
More information9000P Wireless Alarm Owner s Manual
9000P Wireless Alarm Owner s Manual Table of Contents Introduction... 3 Intended Use... 3 System Functionality... 3 Arming your Alarm... 3 Arm Home...3 Arm Away...4 Alarm Triggering... 4 Disarming your
More informationMILLA ELECTRIC FIREPLACE
MILLA ELECTRIC FIREPLACE MODEL NO. 064-3177-0 ASSEMBLY INSTRUCTIONS Toll-free: 1-888-670-6684 IMPORTANT: Please read this manual carefully before beginning assembly of this product. Keep this manual for
More informationHome & Yard Alert Long Range System Home & Yard Alert Extended Long Range System
Home & Yard Alert Long Range System Home & Yard Alert Extended Long Range System USER MANUAL READ THIS ENTIRE MANUAL PRIOR TO INSTALLATION AND OPERATION We thank you for purchasing this Driveway Alert
More informationCOMBINATION ELECTRIC FIREPLACE/HEATER Model #FP23-1A-AKM
LOT NUMBER: DATE PURCHASED: / / USE AND CARE GUIDE COMBINATION ELECTRIC FIREPLACE/HEATER Model #FP23-1A-AKM If you have any questions regarding the use of this unit, or find that your fireplace/heater
More informationP162A Wired PIR Motion Detector
P162A Wired PIR Motion Detector User/Installer Handbook P162A Models covered by this handbook Wired Motion Sensor One of a range of Alert-it Care Alarms available from: UH1118 Alert-it Care Alarms, Atherstone
More informationCLEAN MIST SMART HUMIDIFIER Instruction Manual and Warranty Information IM0031B READ AND SAVE THESE INSTRUCTIONS
CLEAN MIST SMART HUMIDIFIER Instruction Manual and Warranty Information IM0031B READ AND SAVE THESE INSTRUCTIONS Contents Safety Instructions... 1 Unpacking / Specifications... 2 Parts & Contents... 3
More informationInstaller Guide smart connect
Installer Guide smart connect TM 7490 Wireless Remote Outdoor Sensor Please read all instructions before proceeding. The wireless remote outdoor sensor monitors temperature at a remote outdoor location
More informationWeather Day & Night Model: BAR339DP / BAR339DPA / BAR339DPU / BAA339DPH
Weather Day & Night Model: BAR339DP / BAR339DPA / BAR339DPU / BAA339DPH CONTENTS USER MANUAL Overview...2 Front View...2 Back View...3 Remote Sensor...3 Getting Started...3 Main Unit Installation...3 Remote
More informationMicro-Computer Induction Cooktop SR-1885SS
Micro-Computer Induction Cooktop SR-1885SS INSTRUCTION MANUAL Thank you for your purchase. Please read thoroughly before initial use and keep in a safe place for future reference. INDEX Important safeguards....
More informationAmbient Weather RC-8487 ClearView Radio Controlled Travel Alarm Clock with Indoor Temperature User Manual
Ambient Weather RC-8487 ClearView Radio Controlled Travel Alarm Clock with Indoor Temperature User Manual Table of Contents 1. Introduction... 1 2. Getting Started... 2 2.1 Display Features... 2 2.2 Parts
More informationAtomic Projection Alarm Clock
Model: 616-143 Quick Setup Guide DC: 072915 Atomic Projection Alarm Clock Snooze/Backlight Projection Lens Projection Arm Rotation (Front and Back) FRONT VIEW Buttons Projection Focus BACK VIEW AC Power
More informationAtomic Digital Wall Clock
Model: BBB87269 Instruction Manual DC:102015 Atomic Digital Wall Clock Table of Contents Welcome... Get Started... Button Functions... Settings: Time, Date, etc.... Time Zone Settings and 12/24 Hour Time...
More informationWireless External Alarm
Wireless External Alarm Model: SA-001S User s Instructions TABLE OF content INTRODUCTION... 2 INSTALLATION... 2-4 PROGRAMMING LEARN REMOTE OR SENSORS OR CONTROL PANEL... 4-6 ERASE REMOTE OR SENSOR OR CONTROL
More informationTable of Contents What to Expect with. Tools Needed. Mounting Options. Wiring. Switch Housing.
Table of Contents Congratulations on purchasing your new Hunter ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains
More informationRF2352A, HC2351AC (Discontinued), HC2352AC
REMOTE OVERVIEW Your idatastart remote start system may include one or both long-range remotes listed below. Please take a moment to familiarize yourself with their general features. REMOTE MODEL Related
More informationModel: Quick Setup Guide DC: Atomic Projection Alarm Clock. Projection Lens. Buttons. Snooze/Backlight
Model: 616-143 Quick Setup Guide DC: 083017 Atomic Projection Alarm Clock Snooze/Backlight Projection Lens Projection Arm Rotation (Front and Back) Buttons Projection Focus 5.0 VAC Power Jack 616-143 www.lacrossetechnology.com/support
More informationOPERATING MANUAL CUSTOMER SERVICE NO
VERSION: 23-FY17-V03 MODEL : GW-6078TBT Electric Heater Note: This fireplace can be controlled via Bluetooth using your Apple or Android device. Visit the APP Store or Google Play and enter S.W. Link in
More informationIonic Breeze QUADRA Silent Air Purifier. SI637 SI697 Instructions
Ionic Breeze QUADRA Silent Air Purifier SI637 SI697 Instructions INCLUDES IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE SAVE THESE INSTRUCTIONS WARNING: To reduce the risk
More informationAlert-it Care Systems
Alert-it Care Systems P154 Bedside Monitor (with enuresis capability) User Handbook Model P154AB P154BB Description Radio Companion Bedside Monitor (enuresis capable) Wired Companion Bedside Monitor (enuresis
More informationTable of Contents. What to Expect with. Mounting Options. Tools Needed
www.hunterfan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter ceiling fan! It will provide comfort and performance in your home or office for many
More informationWIRELESS COLOR WEATHER STATION
WIRELESS COLOR WEATHER STATION Model: 308-1414 Quick Setup Guide DC: 100814 FRONT VIEW Outdoor Temp + Trends Outdoor Humidity + Trend & Temp Alerts Animated Forecast + Trends Indoor Temp + Trends Indoor
More informationCAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN THE LIGHTNING FLASH AND ARROW- HEAD WITHIN THE
THE LIGHTNING FLASH AND ARROW- HEAD WITHIN THE TRIANGLE IS A W ARNING SIGN ALERTING YOU OF "DANGEROUS VOLTAGE" INSIDE THE PRODUCT. CAUTION RISK OF ELECTRIC SHOCK DO NOT OP CAUTION: TO REDUCE THE RISK OF
More information6 Sheet Strip-Cut Shredder for Home/Office
6 Sheet Strip-Cut Shredder for Home/Office Model #:PS580SC User s Manual PID 011395-109315 Rev. 130928 2 All brand name and trademarks are the property of their respective companies USER S RECORD: To provide
More informationWith Remote Control. English. Model
Digital Ceramic Heater With Remote Control, Owner s Manual English Model HPQ15F-E TABLE OF CONTENTS 2 INTRODUCTION Thank you for choosing the Hunter Ceramic Heater. This manual gives you complete instructions
More informationW-505 W-505 CONTROL BRACKET INSTALLATION W-505 INSTALLATION. CAUTION! Do not use with wall dimmer or rocker switch.
Control includes all of the standard features, in a new design that is compatible with a number of Casablanca fan Models. The hand-held remote provides three forward or reverse fan speeds, full spectrum
More informationTEA CUP SHAPED CLOCK RADIO WITH NIGHT LIGHT
TEA CUP SHAPED CLOCK RADIO WITH NIGHT LIGHT OWNER'S MANUAL KT2055 CAUTION : ELECTRICALLY OPERATED PRODUCT- Please use care when plugging into AC outlet. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
More informationCLEAN MIST SMART HUMIDIFIER Instruction Manual and Warranty Information IM0002E READ AND SAVE THESE INSTRUCTIONS
CLEAN MIST SMART HUMIDIFIER Instruction Manual and Warranty Information IM0002E READ AND SAVE THESE INSTRUCTIONS Contents Safety Instructions... 1 Unpacking / Specifications... 2 Parts & Contents... 3
More informationP162B Radio PIR Motion Detector
P162B Radio PIR Motion Detector User/Installer Handbook P162B Models covered by this handbook Radio Motion Sensor One of a range of Alert-it Care Alarms available from: UH1118B Alert-it Care Alarms, Atherstone
More informationADC-T2000. Smart Thermostat v1.5
ADC-T2000 ADC-T2000 Smart Thermostat User Product Guide Manual 170308 v1.5 Smart Thermostat Product Manual 1 Before installing or servicing the thermostat, turn off power to the system at the circuit breaker.
More informationCLEAN MIST ULTRASONIC HUMIDIFIER. Instruction Manual and Warranty Information READ AND SAVE THESE INSTRUCTIONS IM0040A
CLEAN MIST ULTRASONIC HUMIDIFIER Instruction Manual and Warranty Information IM0040A READ AND SAVE THESE INSTRUCTIONS Contents Safety Instructions... 1 Unpacking / Specifications... 2 Parts & Contents...
More informationWireless Rain Gauge with Rainfall Memory and Digital Clock MODEL: RGR382
Wireless Rain Gauge with Rainfall Memory and Digital Clock MODEL: RGR382 EU-Declaration of conformity... 8 Fcc statement... 8 Declaration of Conformity... 9 USER MANUAL CONTTS Introduction... 2 Main unit
More informationWireless Weather Station. Table of Contents
Wireless Weather Station Model: T83646v2 Instructional Manual DC:071916 For online video support: http://bit.ly/laxtechtalk Table of Contents LCD Features... Buttons... Setup... Set Time, Date etc....
More informationModel: Quick Setup Guide DC: Atomic Projection Alarm Clock. Projection Lens. Buttons. Snooze/Backlight
Model: 616-143 Quick Setup Guide DC: 051916 Atomic Projection Alarm Clock Snooze/Backlight Projection Lens Projection Arm Rotation (Front and Back) Buttons Projection Focus 5.0 VAC Power Jack Battery Cover
More informationAmbient Weather WS-0211 Wireless Wendy the Weather Wizard User Manual
Ambient Weather WS-0211 Wireless Wendy the Weather Wizard User Manual Table of Contents 1. Introduction... 2 2. Getting Started... 2 2.1 Parts List... 2 2.2 Recommend Tools... 2 2.3 Thermometer Sensor
More informationMagic KitchenTM. Talking Chef. Ring! Ring!
Ring! Ring! Talking Chef Magic KitchenTM Model Number: 74839 Please save these instructions for future reference. Adult assembly is required. Requires three C (LR14) alkaline batteries (not included).
More informationCleaning. Owner s Manual. RoboVac 11 SM-A438-V03. For FAQs and more information, please visit:
Cleaning For FAQs and more information, please visit: www.eufylife.com Owner s Manual RoboVac 11 SM-A438-V03 able of Contents 02 Important Safety Instructions 04 About Your RoboVac What's In the Box RoboVac
More informationPour & Float Froggy TM
US User s Manual Pour & Float Froggy TM 2012 VTech Printed in China 91-002702-007 Introduction Thank you for purchasing the VTech Pour & Float Froggy TM! The Pour & Float Froggy TM is full of surprises!
More informationDeLaval activity meter system Instruction Book
Instruction Book 87224201 2014-02-17, Version 4 Original instruction Table of contents EC Declaration of Conformity -... 5 Safety precautions... 7 DeLaval activity meter AM2 DeLaval activity receiver
More informationUser s Manual. Safe & Sound Rescue City VTech Printed in China US IM.indd /5/13 15:05:11
User s Manual Safe & Sound Rescue City 2016 VTech Printed in China 91-003257-000 US 196000IM.indd 1 2016/5/13 15:05:11 196000IM.indd 2 2016/5/13 15:05:13 INTRODUCTION Thank you for purchasing the VTech
More informationRF Projection Clock Model: RM939P POLERMO Projection Clock Model: RM939PA
RF Projection Clock Model: RM939P POLERMO Projection Clock Model: RM939PA USER MANUAL CONTENTS Introduction... 1 Overview... 1 Clock Front View... 1 Clock Back View... 2 LCD Display... 2 Getting Started...
More informationInstruction Manual and Warranty Information
CLEAN MIST TOP-FILL SENSATOUCH HUMIDIFIER WITH REMOTE CONTROL & AROMA TRAY TABLETOP & FLOOR STANDING Instruction Manual and Warranty Information IM0057A READ AND SAVE THESE INSTRUCTIONS Contents Safety
More informationHello Kitty Pancake Maker Item # APP Owner s Manual
Hello Kitty Pancake Maker Item # APP-61209 Owner s Manual Important Safety Precautions When using any electrical appliance, basic safety precautions should always be followed, including the following:
More informationPortable Air Conditioner User Manual
Portable Air Conditioner User Manual Email: usinfo@jmatek.com Web: www.jmatek.com Model / Modèle / Modelo: MN09 Series / Série / Serie: MN09CES, MN09CESBB, MN09CESWW, MN09CHES, MN09CHESBB, MN09CHESWW MN10
More informationIFT-RC150 IntelliFire Touch Remote Control Installation Instructions
IFT-RC150 IntelliFire Touch Remote Control Installation Instructions Leave this manual with party responsible for use and operation. 1. Introduction The IFT-RC150 is a wall mounted device that is designed
More informationWeather Light Model: BAR210 / BAR210U / BAR210A USER MANUAL. EU-Declaration of Conformity...7 FCC Statement...7 Declaration of Conformity...
Weather Light Model: BAR210 / BAR210U / BAR210A CONTENTS USER MANUAL Overview...2 LCD Display...2 Back View...2 Bottom View...2 Remote Sensor...3 Getting Started...3 Power Supply...3 Remote Sensor...3
More informationHSD-200Z Z-Wave Motion Sensor
HSD-200Z Z-Wave Motion Sensor The HSD-200Z is a Z-Wave TM enabled device and is fully compatible with any Z-Wave TM enabled network. Z-Wave TM enabled devices displaying the Z-Wave TM logo can also be
More information+ECO Solar Clock Model: RMR331ES / RMR331ESU / RMR331ESA USER MANUAL CONTENTS
+ECO Solar Clock Model: RMR331ES / RMR331ESU / RMR331ESA USER MANUAL Specifications... 9 Precautions... 9 About Oregon Scientific... 10 EU-Declaration of Conformity... 10 FCC Statement... 10 EN CONTENTS
More informationDigital Thermometer with Ice Alert and Clock
Digital Thermometer with Ice Alert and Clock Model: RAR381 USER MANUAL Specifications... 8 About Oregon Scientific... 8 EU-Declaration of Conformity... 9 FCC Statement... 9 Declaration of Conformity...
More informationCHOKING HAZARD-Toy contains
CHOKING HAZARD-Toy contains a small ball and small parts. Not for children under 3 years. SKU: 55500 AGES 3+ ADULT ASSEMBLY REQUIRED TM Illustrations are for reference only. Styles may vary from actual
More informationApnoea Alarm. Information for parents and carers. MR 10 Respiration Monitor - Apnoea Alarm. Please read this leaflet carefully.
Apnoea Alarm Information for parents and carers MR 10 Respiration Monitor - Apnoea Alarm Please read this leaflet carefully. Item 1. Hanging Loop 8. 10 second Apnoea alarm button 2. Alarm light (Red) 9.
More informationWIRELESS TEMPERATURE & HUMIDITY STATION INSTRUCTION MANUAL
WIRELESS TEMPERATURE & HUMIDITY STATION INSTRUCTION MANUAL MODEL: S82967 DC: 071118 FIND MANUALS, FAQS, AND MORE UNDER THE SUPPORT TAB HERE: www.lacrossetechnology.com/s82967 TABLE OF CONTENTS 3. Power
More informationWith Remote Control. English
Infrared Heater With Remote Control, Owner s Manual English Model H1500RC-CHY H1500RC-BLK INTRODUCTION Thank you for choosing the Hunter Infrared Heater. This manual gives you complete instructions for
More informationModel: v2 Quick Setup Guide DC: Atomic Projection Alarm with Indoor and Outdoor Temperature
Model: 616-146v2 Quick Setup Guide DC: 090116 Atomic Projection Alarm with Indoor and Outdoor Temperature Snooze/Backlight BUTTONS Time, Alarm with Snooze, & Calendar Projection Arm Rotates 180 Indoor/Outdoor
More informationHomeowner s Installation Instructions & Operating Manual
Homeowner s Installation Instructions & Operating Manual ELECTRIC HEATER WITH REMOTE CONTROL Model: EF42D, EF43D, EF44D, EF45D READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE,
More informationGARAGE HEATER WITH REMOTE INSTRUCTION MANUAL MODEL: HA24-100E HA24-150E. Figure 1
GARAGE HEATER WITH REMOTE INSTRUCTION MANUAL MODEL: HA24-100E HA24-150E Figure 1 PET OWNERS WARNING: Health warning for some small pets, including birds, as they are extremely sensitive to the fumes produced
More informationLittle Anne. Important Product Information
EN Little Anne Important Product Information English Little Anne This Important Product Information covers Little Anne, Little Anne AED and Little Anne QCPR. Unless otherwise specified the information
More informationprogrammable control model installation and setup guide M /11/ Hunter Fan Company
programmable control model 99107 installation and setup guide installation Prior to installation, download the app to ensure phone compatibility: Visit your app store and search simpleconnect to find the
More informationModel: Av2 Quick Setup Guide DC: Atomic Projection Alarm Clock
BUTTONS Model: 616-146Av2 Quick Setup Guide DC: 111815 Atomic Projection Alarm Clock Snooze/Backlight Time, Alarm with Snooze Projection Arm Rotates 180 Indoor Temperature + Trends Moon Phase + Calendar
More informationTowel Warmer MAKE EVERYDAY A SPA DAY
Towel Warmer MAKE EVERYDAY A SPA DAY TABLE OF CONTENTS Warnings and Cautions....1 FCC Information...4 Location of Parts and Controls...6 Set Up... 7 Using the Towel Warmer....8 Selecting the Timer...9
More informationHoneywell. Wireless Rain Gauge with Indoor. Temperature (TC152) USER MANUAL TABLE OF CONTENTS INTRODUCTION 3 PRODUCT OVERVIEW 4 REMOTE RAIN GAUGE 7
TABLE OF CONTENTS INTRODUCTION 3 PRODUCT OVERVIEW 4 REMOTE RAIN GAUGE 7 BEFORE YOU BEGIN 9 BATTERY INSTALLATION 10 LOW BATTERY WARNING 11 HOW TO USE THE TABLE STAND 11 GETTING STARTED 11 Honeywell Wireless
More informationModel: S88907 Instruction Manual DC: WIRELESS COLOR WEATHER STATION
Model: S88907 Instruction Manual DC: 072314 WIRELESS COLOR WEATHER STATION FRONT VIEW SIDE BUTTONS Time Calendar + Alarm Color Animated Forecast + Tendency Remote Humidity & Temperature with Trend Indoor
More informationVault Accessories Deluxe Kit
Vault Accessories Deluxe Kit Instructions #1031640 Product #222498 A. B. D. C. E. A. Hygrometer B. 12 Dehumidifier C. Large Hanging Organizer D. Cordless Automatic Vault Light E. Magnetic Barrel Rest F.
More informationCongratulations on your Alert- it purchase
Congratulations on your Alert- it purchase Your product has been manufactured by a team of industry experts with more than 20 years of experience designing, manufacturing and distributing care alarms.
More informationCable Free Weather Station with Thermo-Hygrometer and Radio controlled clock
Cable Free Weather Station with Thermo-Hygrometer and Radio controlled clock MODEL: BAR938HGA USER S MANUAL INTRODUCTION Congratulations on your purchasing of BAR938HGA Cable Free Weather Station with
More informationFEATURES AND SPECIFICATIONS
PRECISE TEMP WIRELESS MULTI-ZONE THERMOMETER and HYGROMETER With CLOCK Model No. 91756 User's Manual BASE STATION REMOTE SENSOR FEATURES AND SPECIFICATIONS BASE STATION Indoor / wireless outdoor temperature,
More information