GMA81 / GMA81A. Operation Manual. Controller for wall mounting

Transcription

1 Operation Manual GMA81 / GMA81A Controller for wall mounting GfG GEELLCHAFT FÜR GERÄTEBAU MBH KLNNETRAE 99 D DORTMUND TELEPHONE +49 / (0) 2 31 / FAX +49 / (0) 2 31 / INFO@GFG-MBH.COM AMTGERICHT DORTMUND HR B 2742 CERTIFIED A PER DIN EN IO 9001:2000 ATEX QM CERTIFICATE

2 Content Introduction 3 For your afety 3 Application and Purpose 3 Monitoring of Combustible Gases in the range % LEL 4 Detection Mode 5 Front View GMA81 5 Function Description 5 Turning On 5 Detection Mode 5 Peak Value Memory 7 Check of Display and Parameter 7 Alarm 7 Early Recognition of Gas Alarm Delta Alarm (Catalytic Combustion Transmitter) 8 Time Delay of Alarms (#) 9 Fault 10 Relays 10 ervice 10 Display of Transmitter ignal 10 Indication of Transmitter in ervice Mode 11 Activation of ervice Menus 11 Adjustments in ervice Mode 11 Check of Relays and Logical Outputs 12 etting of Alarm Thresholds 12 Check and Adjustment of Zeropoint 13 Check and Adjustment of ensitivity 13 Alarm Threshold Hysteresis 14 toring of Changed Parameters and Leaving the ervice Mode 15 Maintenance 15 Inspection, maintenance, calibration and adjustment 15 Regular function tests 15 Overhaul 15 P.C.Boards of GMA Changing of Relay Contacts 17 Influence of Interfering Gases and Oxygen 17 Instruction for Installation and Putting into Operation 17 Putting into Operation 17 Transmitter Cable 17 Remarks concerning the Technical afety of the GMA Trouble hooting 18 ervice Address 18 GMA81 - Gas List 19 Terminal Plan - GMA81 20 Technical Data 21 Annex 22 Terminal Diagram of Transmitters 22 EC-Type Examination Certificate 30

3 Introduction Each detection point of your fixed gas monitoring system consists of a transmitter and a control module GMA81, which are connected by means of a remote sensor cable. The GMA81 provides the power supply for the connected transmitter and receives and processes the sensor signals. Depending on the transmitter type, it monitors the ambient air for the presence of toxic or combustible gases and vapors or for its oxygen content. The GMA81 offers a variety of features, which allow adapting the gas monitoring system to your specific requirements: Reading of linear measurement values in a 3-digit display Menu display 3 variably adjustable alarm thresholds Peak value memory Adjustable relay functions: NC / NO contact, open-circuit / closed circuit Alarm hysteresis prevents flickering of relays 4-20 ma analog output signal. The GMA81 continuously provides information on the measured gas concentration, exceeded alarm thresholds and its operational status. As soon as the gas concentration exceeds one of the three pre-set levels, the GMA81 gives a warning by means of the LED displays and controls the relevant alarm relays. In addition to this, the GMA81 provides the measurement value as an analog output signal for further evaluation. The GMA81 is easy to operate and maintenance-free. hould unexpected failures or system faults occur, the comprehensive failure recognition allows a quick and specific service. For your afety According to 3 of the law about technical working media, this manual points out the proper use of the product and serves to prevent dangers. As any piece of complex equipment, the GfG GMA81 will do the job designed to do, only, if it is used and serviced in accordance with the manufacturer's instructions. All individuals who have or will have the responsibility for using and servicing this product must carefully read this manual. The warranties made by GfG with respect to the product are voided, if the adjustment of functions or parameters is changed without GfG s permission. They are also voided, if the product is not used and serviced in accordance with the instructions in this manual. Please protect yourself and your employees by following them. The above does not alter statements regarding GfG's warranties and conditions of sale and delivery.! Essential Notice: For the parameter setting of the supplied GMA81 please refer to the test report. Modification of functions or parameters may result in deletion of the type test approval. GfG service is always at your disposal for adapting the monitoring system to your specific requirements. Application and Purpose In combination with the connected transmitter, the GMA81 forms a fixed gas monitoring system for continuous measurement of the gas concentration and for the warning from combustible gases and vapors in the range below the LEL, toxic gases in ambient air and oxygen. The type examination of the GMA81 was done by DEKRA-EXAM" for the use as warning of explosible gas mixtures. This examination was based on the standard DIN EN Gas detection instruments General requirements for the operational behavior of devices for the detection of combustible gases and DIN EN Electrical devices for detection and -3-

4 measurement of combustible gases, toxic gases or oxygen Requirements and testing for warning instruments using software and/or digital technology. The test refers to the combination of the GMA81 with any tested 4 20 ma or ma transmitter with linear output signal. In addition to this the GMA81 was tested in combination with the following transmitters with non-linear output signal for the range %LEL (see also page 6): MWG CC 24 EX (type MWG 243x II) for the gases methane and propane MWG 0238 for the gases methane, propane, nonane und ethanol. The functions marked (#) have not been part of the type examination. Type approval: PFG-Nr With connected Ex-transmitters (for detection in explosion endangered areas), the GMA81 is subject to the regulation 94/9/EG (ATEX 100a) as afety, Monitor and Control Device outside of explosion endangered areas and will be labelled, therefore, as follows: II (2)G 0158 BV 03 ATEX G 006 X The EC type approval is based on the type approval PFG-Nr It does not include the operation with the transmitters MWG The model GMA 81 A provides an additional built-in buzzer and an alarm light. This operation manual uses the name GMA 81 for both models. Monitoring of Combustible Gases in the range % LEL The lower explosion limits are to be used according to the national regulations. In Germany the values fixed in the data base CHEMAFE of DECHEMA e.v. in Frankfurt a.m. are valid. If you use catalytic combustion (CC) transmitters for monitoring combustible gases below the LEL, and if a suitable detection range % LEL has been adjusted on your controller, please note the following: Due to the detection principle you cannot differ between sensor signals within the detection range and signals for very high concentrations (e.g. >20Vol% CH4). This is why the GMA81 keeps an overrange signal stored, even if the transmitter sends lower signals in the meantime. This status is characterized by all gas and failure alarms being activated and by the display indicating the overrange situation (see page 8).! Do not press the QUIT button to reset the stored alarm status, before you have made sure that the gas concentration at the transmitter does no longer exceed the LEL range. Use a portable or fixed detector, for example, with a range from 0 to 100 Vol.-% to check. -4-

5 Detection Mode Front View GMA81 Alarm lamp (GMA81 A) Alarm buzzer (GMA81 A) 3 digit display Menu display Key for LED test Key for alarm reset LEDs for alarm 1, 2 and 3 LED for operation LED for fault Keys for parameter adjustment Fig. 1 Function Description Turning On Note: Information for initial putting into operation, see page 17! After having turned the system on, the GMA 81 needs a warm-up time of a few minutes for: the self test, which checks functions, memory (ROM and RAM) and parameter memory (approx. 10 seconds), the warm-up of the transmitter connected (for detailed information please refer to the operation manual for your transmitter). During the warm-up period the GMA81 displays the detection range, the detection unit, measurement gas and the alarm thresholds one after the other. The LED ON flashes alternately with the measurement display and the LED F lis lit, i.e. the fault alarm is active. Alarm thresholds are not activated during the warm-up period. When the GMA81 re-starts after a mains failure, the gas alarms are only evaluated, once the warm-up is completed. After the warm-up the GMA41 automatically turns to detection mode. Detection Mode In detection mode, the green LED ON is lit. If the 3 digit display is activated, it reads the currently measured gas concentration. All gases are measured continuously, and exceeded limit values are noticed and signalized immediately. Electronic functions like parameter memory and transmitters are monitored permanently and the transmitter cable is checked for short circuit and parting of the cable. When operating transmitters with a standard output ma or ma and linear output signal, the following display values of the transmission curve standard occur. The transmitters MWG CC 24 EX (type MWG 243x II) and MWG 0238 are covered by a type examination for the gases methane and propane as well as nonane and ethanol (see table tandard Detection Ranges). -5-

6 The following standard detection ranges have been tested: Gas Formula Detection range MWG CC 24 EX Ex and Function MWG 0238 Function only Methane CH %LEL Curve Methane et at GMA81 Propane C 3 H %LEL Curve Propane et at GMA81 n-nonane C 9 H %LEL linear et at GMA81 Ethanol C 2 H 5 OH %LEL linear et at GMA81 Transmission characteristics of transmitters which have been tested during the type examination Input signal Display in % LEL Current linear transmitters Linearisation for MWG CC 24 EX ma 4 20 ma tandard Methane Propane For transmitter MWG 0238 no transmission characteristics are shown, as for this type there is no durable reference to the input values. For re-adjustment the setting of the amplification is not done on the transmitter but on the GMA41. Transmitter CC28 and the transmitters with electrochemical sensors, e.g. types EC28 or EC24 provide a linear output signal. For these transmitters the GMA 81 uses the transmission characteristic tandard. As the only exception a linearisation is used for the electrochemical detection of oxygen with transmitters EC24 and EC25. For transmitters with sensors using different detection principles, like infrared or chemosorption, there are specific adaptations of the signal curve. This refers to e.g. transmitters MWG IR24, MWG C24, MWG C21 and MWG CI21. The relevant transmission characteristics are shown in the operation manuals of these transmitters. Please refer to the test report of the GMA to see the type of transmitter for which a transmission characteristic has been programmed in the GMA81. The transmission characteristic can only be changed by a GfG service engineer. -6-

7 Peak Value Memory The controller GMA81 provides a peak value memory. Depending on the gas measured by the connected transmitter it stores either the maximum or the minimum value. The peak value memory is not activated during the warm-up time. Gas Oxygen Comb. Gases Toxic gases Peak Value Memory Minimum value Maximum value Maximum value Press key to indicate the peak value in the display. Measuring and warning functions are still working while the peak value is indicated. Press keys and QUIT MENU simultaneously to reset the memory to the present measurement value. Once you release key, the controller returns to the standard display. Check of Display and Parameter! During these checks the measuring and warning functions are not activated! LED Test In detection mode, press key TET MENU shortly to activate the LED test of the GMA81 controller.! Fault LED is not tested just in service menu! Display of Detection Range and Alarm Thresholds Keep key TET MENU pressed for approx. 5 seconds. The LED ON blinks and the display reads the below mentioned parameters one after the other: Display, e.g. LED ON - blinks, additionally lit: Description of Display Detection range 2 LEL, ppm, ppb Detection unit 3 CH4, NH3, O2 Gas GfG-Gas No (value in det. range) A1 1. Threshold alarm 5 40 (value in det. range) A2 2. Threshold alarm 6 40 (value in det. range) A3 3. Threshold alarm Once these readings are complete, the GMA81 turns to detection mode automatically. Alarm The GMA81 provides 3 threshold alarms, which are activated as soon as the gas concentration exceeds or falls below the alarm threshold. An activated alarm is indicated by means of the relevant alarm LED. By pressing the key QUIT MENU or releasing the external acknowledgement (see terminal diagram of BU board GMA81 and technical data) an activated alarm can be acknowledged. -7-

8 Alarm has been activated Relevant Alarm LED flashes has been activated and acknowledged by pressing key QUIT MENU lights permanently Together with the alarm LEDs the GMA81 activates the relevant alarm relay. The model GMA81 A triggers an additional audible and visual alarm by means of the built-in buzzer and alarm lamp. The standard setting for the switching functions is shown below: Alarm Function 1 Nonlatching Resettable during Alarm Resettable after Alarm GMA81 A Alarm Lamp / Buzzer no self resetting flashes / - 2 Latching no yes lights / - Remark 3 Latching yes yes - / sounds Threshold as for alarm 2 Overrange In case the detection range is exceeded by more than 10 %, the GMA81 activates the fault indication in addition to the 3 gas alarms. The display reads. When operating transmitters for the monitoring of %LEL, all alarms and the fault indication are latching, i.e. the overrange can only be reset by pressing key QUIT MENU, when the gas concentration has fallen below the full scale value.! Please notice: Monitoring of Combustible Gases in the Range % LEL, page 4 You can set the switching functions of the three alarms individually. For other settings than the standard one please refer to the test report. Remarks concerning Alarm Functions: Exceeding / Deviating Alarm If the reduction of the measured gas concentration means a hazardous situation, e.g. oxygen deficiency, the alarm is a deviating one. Exceeding alarms indicate a dangerous situation caused by rising gas concentrations, e.g. toxic and combustible gases. Latching / Non-latching Alarm A latching alarm remains valid until it is reset externally, e.g. by pressing key QUIT MENU at the GMA81. A non-latching alarm resets automatically, when the gas concentration falls below or exceeds the preset threshold. Early Recognition of Gas Alarm Delta Alarm (Catalytic Combustion Transmitter) This function is standard available only for the use of catalytic combustion transmitters. hould you wish to activate this function for other transmitters as well, please call your GfG service. The delta alarm is meant for early recognizing of hazards caused by sudden gas concentrations. The alarm activation is defined by the rise of gas concentration within a certain time. As soon as the gas concentration rises by 25 % of the full scale deflection within 1.6 seconds (see fig. 2), the GMA81 indicates overrange.! Please notice: Monitoring of Combustible Gases in the Range % LEL, page 4-8-

9 For the activation of the delta alarm the gas concentration does not need to reach the pre-set alarm threshold. The Delta Alarm is an additional warning to the three thresholds for alarm 1, alarm 2 and alarm 3, which keep their standard functions. Alarm threshold ignal Early alarm activation with Delta Alarm Alarm activation without Delta Alarm Delta Concentration 25% of full scale deflection Early Alarm Activatio Delta Time 1.6 Time Fig. 2 Time Delay of Alarms (#) This function, which is not activated in the standard setting, allows for delaying of the activation of the alarm (fig. 3). hould you wish to activate this function, please call your GfG service. Alarm Alarm without delay Alarm with delay ignal Alarm threshold Timedelay Time Fig. 3 The time delay prevents a warning from gas concentrations only exceeding the threshold for a very short time. It can be set from 0 to 2 minutes. For safety reasons the time delay should be kept as short as possible, and must not be activated in case of time-critical monitoring tasks. -9-

10 Fault In case of failure the yellow LED F lights up and the fault relay is activated. A fault is signalized: if the cable between MWG and GMA81 is cut; if the sensor or the circuit of the transmitter is faulty; if the zeropoint is deviated; if the detection range is exceeded (together with alarm activation); if the CPU self monitoring is faulty. if the CPU self monitoring is faulty. As soon as the fault is repaired, the yellow LED F goes out, the fault relay deactivates and the GMA81 returns to standard detection mode. Relays The GMA81 provides 4 relays: 3 alarm relays for controlling external alarm devices, 1 fault relay for signalizing of failures. The switching behavior of the relays is the same as for alarm or fault signals. Every relay can be operated as NC or NO contact in closed or open circuit systems. In the standard setting all 4 relays are NO contacts. The alarm relays are operated as open circuit system; the fault relay is a closed circuit. This results in the below mentioned switching functions: In the standard setting the switching functions of the relays are as follows: Relay for: Alarm 1 Alarm 2 Alarm 3 Fault The relay switches: in during gas alarm after gas alarm in case of in case of in case of detection not reset not reset mains failure failure gas alarm mode reset reset and failure (no gas)! It is essential to take note of the switching behavior of the relays when connecting external devices. In the standard setting alarm 3 (buzzer relay) can be reset even during gas alarm! For special settings of the relay switching functions please contact your GfG service. ervice Display of Transmitter ignal Press key and after approx. 2 seconds the GMA81 displays the signal received from the transmitter in ma ( ma for transmitters with ma output and ma for transmitters with 4-20 ma output). This function allows for checking of the zero point of the transmitter at the GMA81 (see page 13). -10-

11 Indication of Transmitter in ervice Mode! This function is only available for CC24 EX (type 243x II), C24 EX and EC25, CC28 and EC28. The transmitters CC24 EX, C24 EX, EC25 provide a service switch. When this is activated during maintenance (see operation manual for the transmitter), the GMA81 automatically turns to fault indication. Alarm signals are being suppressed. Activation of ervice Menus! The ma voltage output continuously reads the actual measurement value! The service menus allow to select and to change all important parameters of the GMA81. A security code protects the service menus A and B from accidental maladjustment and unauthorized access. Adhere to the following procedure to enter the service menus: 1. Press key QUIT MENU display., then key TET MENU 2. Use keys and to enter the security code. and keep both keys pressed, until ER is read in the ecurity Adjustments Code Menu A 11 Alarm thresholds and adjustment Menu B 222 Deactivation points of alarm thresholds 3. Press key QUIT MENU to confirm the entered security code. The GMA81 turns to the selected service menu or Press key TET MENU to return to detection mode. In the service mode the gas alarms are locked. The GMA81 switches to fault. The LEDs ON and F light up, the fault relay is activated. If in service mode you do not hit any key within 4 hours, the GMA81 returns to detection mode automatically. Any parameter changes will not be stored. Adjustments in ervice Mode The display of the GMA81 reads the set parameters. The menu display indicates the menu point, where the displayed parameter value can be found. Use keys TET MENU and QUIT MENU to scroll forward and back. For changing of parameters use keys and. -11-

12 urvey of Menu Points Menu TET MENU QUIT MENU Description Display, e.g. Parameter etting Detection unit LEL, ppm Display only Gas Threshold Alarm 1 Threshold Alarm 2 Threshold Alarm 3 Zeropoint adjustment 0 CH4, NH3, O2 or GfG-Gas No. Value in detection range Value in detection range Value in detection range Adjustment with and ensitivity adjustment Value in detection range Menu B TET MENU QUIT MENU Description Display, e.g. Parameter etting Threshold Alarm 1 Threshold Alarm 2 Threshold Alarm 3 Value in detection range Value in detection range Value in detection range Adjustment with and Check of Relays and Logical Outputs The display of the GMA 81 reads rl. The relays and logic outputs can be switched, one after the other, by pressing the keys and At the GMA81A the alarm lamp and the buzzer are activated as well. The relevant LEDs for alarm and fault indicate, which relay (and which logical output) was activated. When you set up this menu all alarms are deleted and afterwards newly set. etting of Alarm Thresholds 1. Activate service menu A. 2. Use keys TET MENU and QUIT MENU to select menu point, or for the alarm threshold to be set. 3. et the new alarm threshold by means of keys and. 4. tore the parameters (see page 15). Adjustable alarms Highest alarm Lowest alarm End of measurement range Begin of measurement range + Hysteresis It depends on the measurement task and on the transmitter, which adjustment of the lowest alarm threshold makes sense. When detecting combustible gases in the range %LEL, no alarm should be set to less than 10 %LEL; for most applications the lowest alarm should not be set to less than 5 % of full scale. -12-

13 Check and Adjustment of Zeropoint 1. upply zero gas to the transmitter or make sure, that the ambient air is free from interfering gases. Zero gas is a test gas, which is free from combustible or any other interfering components. For details about the gas supply please refer to the operation manual of your transmitter. 2. Wait until the display value is stable. The zeropoint must be adjusted, if the display is different from 0. Use key to check the transmitter signal. An adjustment of the zeropoint is only possible, if the transmitter signal is within a tolerance band: For a transmitter with ma: Tolerance of ma For a transmitter with 4 20 ma: Tolerance of ma (Depending on the transmitter, slightly different tolerances are possible.)! If the transmitter signal is out of the tolerance band, the zeropoint has to be adjusted at the transmitter first! For details please read the operation manual of the transmitter! 3. Activate service menu A. 4. Use keys TET MENU and QUIT MENU to select menu point. 5. Press key for 3 seconds to adjust the zero point The adjustment of the zero point was successful, when the value 0 is flashing in the display. If the display is not flashing, the transmitter signal is out of tolerance and has to be adjusted at the transmitter first. Please adhere to the operation manual of your transmitter. 6. Disconnect the zero gas from the transmitter. In case of transmitters for oxygen wait until the displayed gas concentration exceeds the threshold alarm. 7. tore the parameter. After the zeropoint adjustment, the sensitivity needs to be checked and eventually adjusted. Check and Adjustment of ensitivity Note: Before checking the sensitivity, make sure that the zeropoint is set correctly. The GMA81 allows to check and adjust the sensitivity by means of the peak value memory. This memory is activating automatically, when the menu point is turned on for 2.5 minutes. The GMA81 indicates the activated peak memory by a flashing display. Check and Adjustment of ensitivity without Peak Memory 1. Activate service menu A. 2. Use keys TET MENU and QUIT MENU to select menu point. 3. upply test gas to the transmitter. For details about the gas supply please refer to the operation manual of your transmitter. 4. Wait until the display value is stable. The sensitivity must be adjusted, if the displayed value is different from your test gas concentration. 5. Use keys and to set the parameter value to the concentration of your test gas. 6. Disconnect the test gas supply from the transmitter. In case of transmitters for toxic or combustible gases wait until the displayed gas concentration falls below the threshold alarm. 7. tore the parameter. -13-

14 Check and Adjustment of ensitivity with Peak Memory This adjustment uses the possibility of the GMA81 to store the peak signal value measured during the duration of the test gas supply. The store peak values can be used as sensitivity point. Fig. 4 below shows this procedure. ignal stored peak signal = test gas concentration Clear memory Gas supply to MWG Exposition end Calibration at controller Time Fig Activate service menu A. 2. Use keys TET MENU and QUIT MENU to select menu point. 3. After 1.5 minutes supply test gas to the transmitter and make sure that the gas is supplied constantly for at least 3 minutes For details about the gas supply please refer to the operation manual of your transmitter. 4. Disconnect the test gas source from the transmitter. 5. Use keys and to set the parameter value to the test gas concentration. 6. tore the parameter. Alarm Threshold Hysteresis This function allows to adjust the hysteresis (point of deactivation) of the alarm thresholds. For exceeding alarms this point can be set from the start of the detection range up to two digits below the alarm threshold. For deviating alarms the deactivation point can be set from two resolution units above the alarm threshold up to the end of the detection range. The parameter setting is done in the unit of the gas to be measured. Example: The hysteresis of a controller, which monitors gas in the LEL range, was set to 18 % LEL for alarm 1, 36 % LEL for alarm 2 and 54 % LEL for alarm 3. This results in the alarm activation below: Alarm 1 Alarm 2 Alarm 3 Alarm threshold = 20 % LEL = 40 % LEL = 60 % LEL Alarm activation 20 % LEL 40 % LEL 60 % LEL Alarm deactivation 18 % LEL 36 % LEL 54 % LEL Adjustment of deactivation point: 1. Activate service menu B. 2. Use keys TET MENU and QUIT MENU to select menu point, or for the alarm deactivation point to be set. 3. Use keys and to adjust the new deactivation point. 4. tore the parameter. -14-

15 toring of Changed Parameters and Leaving the ervice Mode All changes done in the service mode have to be stored: 1. Press keys TET MENU and QUIT MENU simultaneously to activate the memory function. The display reads to. 2. Confirm storage: Press key QUIT MENU to confirm the storage of the parameter. The GMA81 stores all changed parameters and returns to detection mode. or No storage: Press key TET MENU, and the GMA81 returns to detection mode without storing the changed parameters. You can change several parameters one after the other, without storing them individually. Once you have set all parameters, one storage confirmation is sufficient to store all changed parameters. Maintenance After the installation of a gas warning system and before putting it into operation, a function test must be carried out. DIN EN Gas detection instruments - election, installation, use and maintenance of devices for detection and measurement of combustible gases or oxygen as well as the relevant national directives are to be obeyed. In Germany this means the Explosion protection regulations, the guideline T 023 (BGI 518) Gas warning devices for explosion protection Use and operation and BGR 500 part 2 chapter 2.33, 4.4 Test of gas warning devices. After installation and at the initial putting into operation, an expert has to do a function test of the gas warning system (see DIN EN chapter 8.9). The maintenance of a gas warning system includes inspection, service, calibration and adjustment, the regular function test and repair. Tests must be done by an expert, who has to report the result in writing. Inspection, maintenance, calibration and adjustment During the inspection examinations of the gas measurement systems shall be carried out (see information sheet T023, section 9). - Pollution by dust - Condensation by humidity - Protective equipment for transmitters - Diffusion inlet for the transmitter Maintenance and adjustment describe those measures, which retain the nominal status of the gas warning system. They shall be checked in regularly inspection intervals. Inspection intervals should not exceed 4 months. (ee DIN EN section 11 and in Germany information sheet T023, section 9.2, 9.3). - Zeropoint - ensitivity - Activation of alarm thresholds - Response time - Alarm output visible and audible - Fault report Regular function tests Additionally to the maintenance the function of the gas warning system has to be examined regularly. The function tests may not exceed a period of one year. (for Germany see information sheet T023, ection 9 and BGR500, part 2, chapter 2.33, 4.4). Overhaul Overhaul describes all repairs and exchange of components. This has to be done by the manufacturer or persons authorized by him. Only those spare parts and structural components that have been tested and approved by GfG may be used for exchange. -15-

16 ! Disregard affects the detector safety, the type approvals are void, resp. the detectors are not operated according to ATEX. We recommend a regular function test and overhaul and to call GfG's service for the regular maintenance. P.C.Boards of GMA 81 The GMA81 controller includes two p.c.boards: Main Card econdary fuse Transformer Voltage-free relays for: Fault Alarm 1 Alarm 2 Alarm 3 Primary fuse Code bridge for relays Open-circuit current NO Closed current NC NC NO Terminals Fig. 5 Display Card 3-digit display for gas concentration Menu display LEDs Connection for configuration plug Keys Fig

17 Changing of Relay Contacts On the main card of the GMA81 controller every relay has two assembly positions for code bridges. By selecting the position of the code bridge you can determine, whether the relay works as a NC contact or as a NO contact. Influence of Interfering Gases and Oxygen Interfering gases, oxygen surplus and oxygen deficiency may affect the measurement of gases by the transmitter. Please adhere to the operation manual of your transmitter. Instruction for Installation and Putting into Operation The GMA81 controller must not be installed in hazardous areas. It shall preferably be vibration-free installed. Vibration load may cause short-term fault reports at the relay outputs. The transmitter and the mains supply are connected as shown in the terminal diagram. Make sure that the shield of the transmitter cable is grounded on the printed circuit board. Once the GMA81 is mounted to a wall, all transmitters, control groups and the mains supply are connected, an expert can put the system into operation. For installation and putting into operation of the transmitters please see the operation manual of your sensor. Putting into Operation After installation gas warning systems have to be tested for faultless functioning, be adjusted and put into operation, by an expert. The testing and adjustment shall be carried out in accordance with the manufacturers operation manual. They are only allowed to be carried out by an expert. The expert has to write a confirmation on the results (see information sheet T 023 8/99, section 6.3, as well as DIN EN 50073, ection 6.4.1). Please call GfG s service, or an expert authorized by GfG for putting into operation. Transmitter Cable The GMA81 controller and the transmitter are connected by means of a shielded transmitter (data) cable (LIYCY). The cross section of the cable cores depends on the current consumption of the transmitter and on the cable length (see connection diagram in the manual s annex). Even with the maximum cable lengths the specific power supply for the transmitter has to be guaranteed. For detailed information please refer to the operation manual of your transmitter. Remarks concerning the Technical afety of the GMA 81 Contact Protection Mains supply and relay contacts of the GMA81 provide insulation distances of 3 mm, i.e. they are designed for 250 V operational insulation. In case a contact is operated on a contactcritical potential, the contacts close to it are also considered as contact-critical. According to contact protection the contacts are not considered to be separated safely. Resulting from this, the same applies to the relay contacts of a controller operated on 230 V. Here an operational insulation has been provided as well. The insulation of the secondary circuit from the primary circuit and the relay contacts complies with the requirements for contact protection. Distances of 6.5 mm ensure a safe separation. The secondary circuit operates on extra-low safety voltage. -17-

18 Trouble hooting Failure Cause olution LED " F" lights, display EEP LED " F " lights, LED ON flashes LEDs do not light ensor signal, but gas-free atmosphere Display LED F lights Display LED F lights - ystem error, fault in parameter memory - ystem is in warm-up period, alarm suppression is still active - Faulty voltage supply, defective fuse or mains unit - Incorrect calibration, incorrect zeropoint adjustment - ADC overrange - stored overrange - short circuit at the transmitter cable - Display deviation (< -99) - ADC range deviation - Cable cut - Zeropoint deviation by I IN 3,00mA (signal input 4..20mA) I IN 0,15mA (signal input 0,2..1mA) - ervice-signal / transmitter - short circuit at the transmitter cable - Re-start of system - Call GfG service - Wait until warm-up period is over - Ensure proper voltage supply - Adjust the zeropoint, calibrate - If there is a gas-free atmosphere at the transmitter, you can reset the stored measurement value Check transmitter cable - Check transmitter cable - Check calibration of transmitter and GMA controller - Check transmitter cable - Check calibration of transmitter and GMA controller Check service key - Check transmitter cable ervice Address For additional questions on the product or in case of failure and problems please contact: GfG Gesellschaft für Gerätebau mbh Klönnestraße 99 D Dortmund Phone: Fax: info@gfg-mbh.com -18-

19 GMA81 - Gas List Gas Nr. Gas Chemical Formula GMA Nr Gas Nr. Gas Chemical Formula 1 Aceton CH6O 1 55 Carbon dioxide CO2 CO2 2 Acetonnitrile C2H3N 2 56 Carbon monoxide CO CO 3 Acetylene C2H Coke gas CO, CH4, H Acrylnitrile C3H3N 4 58 Air N2, O2, CO Aminopropane C3H9N 5 59 Methane CH4 CH4 6 Ammonia NH3 nh3 60 Methanol CH4O 60 7 Amyl alcohol C5H12O 7 61 Methyl acetate C3H6O Benzine 60/95 Mixture 8 62 Methyl alcohol CH3OH 62 9 Benzine 80/110 Mixture 9 63 Methylbutylketone C6H12O Benzine (fuel) Mixture Methyl chloride CH3Cl Benzene C6H Methylene chloride CH2Cl Comb. gases and vapours Mixture Methyl-i-butylketone C6H12O Bromtrifluoromethane (Halon) C Br F Methylethylketone C4H8O Butadien C4H Methylglycol C3H8O n-butane C4H10 but. 69 Methylmethacrylate C5H8O i-butane (CH3)3CH Methylpropanol C4H10O Butanol - 1 C4H10O Monochlordifluormonobrom. C Br Cl F Butanon - 2 C4H8O n-nonane C9H20 non. 19 n-butylacetate C6H12O i-octane C8H i-butylacetate C6H12O n-octane C8H n-butyl alcohol C4H10O i-pentane C5H Butylene C4H n-pentane C5H Chlorine Cl2 CL2 77 Pentanon-2 C5H10O Chloromethane CH3Cl Penten-1 C5H Hydrogen chloride HCl HCL 79 Pentyl acetate C7H14O Hydrogen cyanide HCN hcn 80 Perchloroethylene C2Cl Cyclohexane C6H Propane C3H8 Pro. 28 Cyclopentan C5H Propanol-2 C3H8O Cyclopropane C3H i-propyl acetate C5H10O Dichlordifluoromethane (R12) C Cl2 F n-propyl acetate C5H10O Dichlorethane C2H4Cl n-propyl alcohol C3H8O Dichlorfluoromethane (R21) CH Cl2F i-propyl alcohol C3H8O Dichloromethaen CH2Cl Propylene C3H Dichloropropane C3H6Cl Propylenedichloride-1.2 C3H6Cl Diethylamine C4H11N Oxygen O2 O2 36 Dimethylether C2H6O ulfur dioxide O2 O2 37 Epichlorhydrin C3H5Cl O ulfurhexafluoride F Natural gas (H+L) Cn Hm, N Hydrogen sulfide H2 H2 39 Ethane C2H Town gas CO, CH4, H Ethanol C2H5OH Eol. 94 Nitrogen dioxide NO2 no2 41 Ethyl acetate C4H8O Nitrogen monoxide NO no 42 Ethyl alcohol C2H6O tyrene C8H Ethylen C2H Tetrachloroethane C2Cl Ethylen oxide C2H4O Toluene C7H FAM-Benzine Mixture Trichloroethane C2H3Cl Jet fuel 40/180 Mixture Trichloroethylene C2HCl Formaldehyde CH2O Trifluoromethane (R23) CH F Frigen 22 CH Cl F2 r Vinyl acetate C4H6O Helium He Vinyl chloride C2H3Cl Heptane C7H Hydrogen H2 H2 51 n-hexane C6H Water gas H2, CO, CH i-hexane C6H Xylene C8H Hexanon-2 C6H12O Ozone O Isobutyl acetate C6H12O2 54 Chart 1 - GfG-Gas List GMA Nr -19-

20 Terminal Plan - GMA81 GMA81 Relay functions, see page ensor upply approx.24 V Ground ignal 4..20mA / mA Alarm Alarm Alarm Fault L N PE Mains connect 230 V AC 50/60 Hz Ground ignal output 4..20mA hield Voltage supply 24 V DC + external reset V DC Terminal bar GMA81 / GMA81A Voltage supply, 230V/AC or 24V/DC Voltage supply Terminal Voltage supply Terminal 230 V AC L1 18 Ground, GND 4 Neutral N 17 Voltage supply 6 or! +24V/DC Protection PE 16 Alarm relays (default setting) Terminal Alarm 1 Alarm 2 Alarm 3 törung Transmitter Transmitter 1 Voltage supply 24 V / DC 1 Ground, GND 2 ignal input 0,2.. 1 ma or ma 3-20-

21 Technical Data Gas Monitor GMA81 for wall mounting Type: GMA81, software version 2.03 Dimensions: 130 x 185 x 95 mm (WxHxD) Gas Monitor GMA81 A incl. Buzzer and alarm lamp, for wall mounting Type: GMA81 A, software 2.03 Dimensions: 135 x 217 x 95 mm (WxHxD) Power supply Operational voltage: Current consumption: Primary fuse: econdary fuse: V DC (Uin) [21 to 28 V] or V / 50Hz or 115 V / 60 Hz max. 11 W at 230 V AC T 0.08 A G melt fuse T 0.50 A G melt fuse Climate Conditions for operation: 0 to +55 C, 0 to 99 % r.h. 700 to 1300 hpa recommended storage conditions for GMA81(A), accessories, spare parts: -25 to +50 C, 0 to 99 % r.h. Transmitter connection Transmitter connection: Voltage supply output: Input signals: 2-, 3-wire transmitter 20 V DC max. 250 ma ma, ma Outputs Analog outputs for meas ma, max. load 200 (T 90 = 18 sec.) value: Display and alarm activation: T 90 < 3 sec. ensor signal display: ma Max. deviation: < 0.2 ma ±0.04 ma ma 0.02 ma > 0.5 ma ma ma Max. deviation: < 4 ma ± 0.08 ma ma 0.4 ma > 10 ma + 1 ma Relays: External reset: max. switch voltage 250 V AC 50/60 Hz or 250 V DC max. switch current 4 A AC/DC max. switch performance 1000 VA AC or depending on voltage W DC Relay outputs and mains entry are operation insulated High active from V DC (input resistance 11kΩ) afety Protection: DIN EN IP -54 Approvals Protective separation: by safety transformer type: EI 48/205 (V11419) PRI 230V / EC 20 V 50-60HZ Protective insulation: as per EN up to over voltage category III and soiling degree 2 EMC test: As per EN : 2006 EC-Type Examination-Function PfG-Nr (for tested detection ranges see page 4) II (2)G BV 03 ATEX G 006 X (EC-Type Examination Certificate) Production supervision: 0158 (Notified body: DEKRA-EXAM) -21-

22 Annex Terminal Diagram of Transmitters Transmitter CC 0238 EX This CC transmitter is a 3-wire transmitter. The supply line and the 0.2-1mA output signal use the same ground line. Cable type: e.g. LiYCY 3 x 0.75 mm² (up to 200 m). MWG 0238 EX M U GMA81 Terminals (U) upply: 24V DC (M) Ground () ignal: mA to sensor ensor hield hielding of cable is effected via EMC cable screwing -22-

23 Transmitter C 21 and CI 21 The C 21 and CI 21 sensors are designed as 3-wire transmitters mA output signal The supply voltage and the ma output signal use the same ground line. Cable type: e.g. LiYCY 3 x 0.75 mm² (up to 200 m) MWG C 21 MWG CI 21 M U hielding of cable is done over the EMCcable screwing GMA81 terminals (U) upply: 24V DC (M) Ground () ignal: mA to sensor hield ensor 4-20mA Output signal The voltage supply and the 4-20 ma output signal use the same ground line MWG C 21 MWG CI 21 M U hielding of cable is done over the EMCcable screwing GMA81 terminals (U) upply: 24V DC (M) Ground () ignal: mA to sensor hield ensor -23-

24 Transmitter EC 24 (models MWG 2412, 2414, 2411 and 2413) 4-20 ma output signal The EC sensors MWG 2412 and MWG 2414 are designed as 2-wire transmitters. The 4-20 ma output signal is provided via the supply line. MWG 2412 MWG 2414 () M U hielding of cable is done over the EMCcable screwing GMA81 terminals (U) upply: 24V DC (M) Ground () ignal: mA hield ensor ma output signal The EC sensors MWG 2411 and MWG 2413 are designed as 3-wire transmitters. The voltage supply and the ma output signal use the same ground line. MWG 2411 MWG 2413 M U hielding of cable is done over the EMC cable screwing GMA81 terminals (U) upply: 24V DC (M) Ground () ignal: mA hield ensor -24-

25 Transmitter CC 24 EX (models MWG 2431 and 2432), Transmitter C 24 EX (models MWG 2471 and 2472), Transmitter IR 24 (models MWG 2491 and 2492) ma output signal The CC sensor model MWG 2431, the C sensor model MWG 2471 and the IR sensor model MWG 2491 are designed as 3-wire transmitters. The supply voltage and the ma output signal use the same ground line. MWG 24.. MWG MWG 2471 MWG 2471 MWG 2491 MWG 2491 U M hielding of cable is done over the EMC cable screwing GMA81 terminals (U) upply: 24V DC (M) Ground () ignal: 0,2... 1,0mA to sensor hield ensor 4-20 ma Output signal The CC sensor model MWG 2432, the C sensor model MWG 2472 and the IR sensor model MWG 2492 are designed as 3-wire transmitters. The supply voltage and the 4-20 ma output signal use the same ground line. MWG 24.. MWG 2432 MWG 2472 MWG 2492 U M hielding of cable is done over the EMC cable screwing GMA81 terminals (U) upply: 24V DC (M) Ground () ignal: mA to ensor hield ensor -25-

26 Transmitter EC 25 (models MWG 2502, 2504) without Ex-Barrier 4-20 ma output signal The EC sensor models MWG 2502 and MWG 2504 are designed as 2-wire transmitters. The 4-20 ma output signal is provided via the supply lines. MWG 2502 MWG V 1 hielding of cable is done over the EMCcable screwing GMA81 terminals (U) upply: 24V DC +/- 0V +ig. 2 3 () ignal: mA - ig hield ensor ma output signal The EC sensor models MWG 2501 and MWG 2503 are designed as 3-wire transmitters. The supply voltage and the ma output signal use the same ground line. MWG 2501 MWG V +/- 0V +ig hielding of cable is done over the EMCcable screwing GMA81 terminals (U) upply: 24V DC (M) Ground () ignal: mA - ig hield ensor -26-

27 Transmitter EC 25 EX (model MWG 2501) with Ex-Barrier The EC sensor model MWG 2501 is designed as a 4-wire transmitter. upply and signal lines are separated. The transmitter is considered as 4-pole. For reasons of explosion protection, Ex-barriers are linked between transmitter and GMA81 both in the supply lines and in the signal lines. MWG V +/- 0V + ig. - ig hielding of cable is done over the EMCcable screwing GMA81 terminals (U) upply: 24V DC (M) Ground () ignal: mA upply barrier hield ib+ Un+ ensor ib - Un - PA Evaluation barrier Potential compensation ib+ ib - PA Un+ Un - Transmitter CC28 Transmitters CC28, CC28 D and CC28 DA are connected to the GMA81 via 3 wires. Voltage supply and output signal are using the same ground line. Cable type: e.g. LiYCY 3 x 0,75 mm² (up to 200m) LiYCY 3 x 1,5 mm² (up to 1 km) () (M) (U) GMA 81 terminals (U) upply: 24V DC (M) Ground () ignal: mA CC28 CC28 D CC28 DA hield ensor hielding Abschirmung of cabel des Kabels is done erfolgt over über the EMC die cable EMV-Kabelverschraubung screwing -27-

28 Transmitter EC28 (part 1) Transmitters EC28, EC28 D, EC28 DA and EC28 DAR are connected to the GMA81 via 3 wires. Voltage supply and output signal are using the same ground line. Cable type: e.g. LiYCY 3 x 0,75 mm² (up to 500m resp. 200m for EC28 DA/DAR) LiYCY 3 x 1,5 mm² (up to 1 km) () (M) (U) EC28 EC28 D EC28 DA EC28 DAR GMA81 Terminals (U) upply: 24V DC (M) Ground () ignal: mA hield ensor Abschirmung hielding of des cabel Kabels is done erfolgt over über the EMC die cable EMV-Kabelverschraubung screwing Transmitter EC28 (part 2) Transmitters EC28 i and EC28 Di are connected to the GMA81 via 2 wires. Voltage supply and output signal are using the same wire. Cable type: e.g. LiYCY 2 x 0,75 mm² (up to 500m) LiYCY 2 x 1,5 mm² (up to 1 km) If the transmitter is installed in explosion endangered areas, connection must be done through a safety barrier 4 () (U) eigensicher Intrinsically safe i i GMA81 Terminals (U) upply: 24V DC EC28 i EC28 Di () ignal: mA Ex-protection safety barrier hield ensor hielding Abschirmung of cabel des is done Kabels over erfolgt the über EMC die cable EMV-Kabelverschraubung screwing -28-

29 If the transmitter is not installed in explosion endangered areas, it may be connected to the GMA81 without an interlinked safety barrier () (U) GMA81 Terminals (U) upply: 24V DC EC28 i EC28 Di () ignal: mA hield ensor hielding of cabel is done over the Abschirmung des Kabels erfolgt über EMC cable screwing die EMV-Kabelverschraubung Worldwide upplier of Gas Detection olutions File: _OM_GMA81.doc, Edition , oftware Version 2.03, We reserve the right of modification GfG- Gesellschaft für Gerätebau mbh Klönnestr. 99, D Dortmund Phone: +49-(0) Fax: +49-(0) info@gfg-mbh.com Internet:

30 EC-Type Examination Certificate -30-

31 -31-

32 -32-