CH4 SO2NO2. C O2 mount options. The controller has two SPCO relays as standard with three 4-20mA outputs and an RS485 Modbus UK Design And Manufacture

Transcription

1 el: +44 (0) Fax: +44 (0) SYS HS S is a multi-channel detector controller in an easily installed and implemented small format package. he system can be used with any of the ocsin Addressable range detectors or I/ modules providing maximum flexibility. he controller can be wall mounted or panel mounted and has a pump and duct mount options. he controller has two SP relays as standard with three 4-0mA outputs and an S48 Modbus UK Design And Manufacture Features Flexible Power Supply ptions Wall or Panel Mounting elay utputs as Standard Standard Specifications Power 110/V A 0/60Hz W Standard 4V D ption onstruction ABS Display Lines x 8 Digit LD Display Multi-olour Backlight (ed-alarm, Yellow-Fault, Blue-ormal) utputs off SP elays 4A on-inductive User onfigurable 3 off 4-0mA Linear utputs User onfigurable ther I/ Sounder 100mm (Mutable) S48 Port Modbus Inputs 8 off Addressable Series Detectors or I/ Modules emperature - to Deg Humidity 0-9% H on-ondensing Sealing IP4 Mounting Wall Mount, Panel Mount Kit ption, Duct Mount Kit ption Weight 840g 4-0mA utputs as Standard S48 Modbus as Standard ontrol up to 8 Devices as Gas Detectors or I/ Modules LD Display With Multi olour Backlight, Flashes ed on Alarm, Flashes Yellow on Fault etc Battery Backup ption LPG interface.

2 el: +44 (0) Fax: +44 (0) SYS HS S E Declaration of onformity Issuers name and address: Declares that the product listed as: liver IGD Limited of 4a Pepper d Stockport, SK7 BW United Kingdom Single or Multi-hannel Detector ontrol Panel Are in conformity with the provisions of the following European Directive(s) when installed, operated, serviced and maintained in accordance with the installation and operating instructions contained in the product documentation. 004/108/E 006/9/E Directive Low Voltage Equipment Directive (note not applicable to 4V D Powered Versions) And that the standards and/or technical specifications referenced below have been applied or considered. E :000 Electrical apparatus for the detection and measurement of flammable gases, general requirements and test methods. E 071:001 Electrical apparatus for the detection and measurement of combustible gases, toxic gases or xygen: requirements and tests for apparatus using software and or digital technologies. Excluding requirements for SIL echnical File eference 6-F9 otified Body For AEX and/or QA: Sira est & ertification Ltd Hazardous Area entre, ake Lane Eccleston, hester, 9J. United Kingdom liver IGD Limited operate an independently assessed IS9001:008 Quality Assurance System and AEX QA. Quality Assurance ertificate umber 0387 esting Agency: ASS Industries Limited Blackbrook rading Estate Weybrook d Levenshulme Manchester M19 QD Quality Assurance otification umber SIA 0AEX M174 Issued on: At liver IGD Limited, Stockport, SK7 BW, United Kingdom Signature: Declaration of onformity in accordance with E IS/IE :004 ame Andrew J ollier M.I..D Position: Managing Director Date:.ctober 011 Declaration ef: -DE-1

3 el: +44 (0) Fax: +44 (0) SYS IAQ HS S EA VIEW WALL MUIG PI DEAILS 4.mm SEWS 3 1 EA VIEW EA EY KK US 0mm DIA SIDE VIEW PAEL MU VESI (LAMP) F VIEW ptional Panel Mounting Kit P PAEL U U ALAM 1 GAS DEEI SYS FAUL SELE PWE 01 ptional Battery Backup Kit P BM VIEW 4 HLES DIA 0mm ote this module uses the same style enclosure as the and houses batteries and charge control. It is usually mounted below the and is supplied with all required connectors. PAEL U U

4 el: +44 (0) Fax: +44 (0) SYS H HS S DE DES ALAM 1 GAS DEEI SYS ontroller 110/V A ontroller 4V D ontroller Panel Mount Kit Battery Backup Module FAUL SELE PWE -BBU BAEY BAKUP UIG MAIS UIG BAEY ombine ontrollers With Detectors and I/ odes as equired For safe area detectors refer to the ocsin 103 Series Gas Detectors For Hazardous areas refer to the ocsin 10 Series Gas Detectors 103 If I/ odes are required refer to ocsin 107 Series Data Sheets 107 ALAM 1-0 FAUL GAS DEE AGE 0-000ppm P H 0-100% ESE efer to -, -10 and -0 series detectors for residential, light commercial and ventilation detectors for flammable gases,, temperature, humidity and Indoor Air Quality PWE

5 el: +44 (0) Fax: +44 (0) SYS HS S H6 Analogue utput Interfaces +4V D - 4V D ma Sig 1 ma Sig ma Sig 3 Front View over pen ote as standard ma outputs are set. hese can be re-configured as 0-10V signals Mains Power onnector 110/V A 0/60Hz L L nc nc E onnect to detectors and nodes using 4 core 1.mmSQ Y style cable or FP00 style cable as appropriate. able screens should be terminated as indicated Detector I/ Interface 0V D A B 4V D onnect up to 8 addressable devices. hese can be Gas Detectors or by using the available I/ odes any 4-0mA Device such as pressure or temperature transmitters, read these back to the control panel as any other detector and set alarms as required. S 0V D A B 4V D Detector S 0V D A B 4V D S 0V D A B 4V D 4V D Input 1 Input 0V D I/ ode elay 1 elay 1 elay elay S 0V D A B 4V D L 1 S48 Modbus omms Port 0V D A B 4V D ormally losed onnections common to each of ommon ormally pen the two relay outputs Gas detectors count as one device, there can be any mix of gas detector types on the highway. For example Flammable Gas Detectors, arbon Monoxide, xygen etc. Each I/ ode counts as one device and can be used to interface to analogue devices and provide additional relay outputs where they are needed to control items such as beacon-sounders, solenoids or interfaces to fire panels. Depending on loading external power may be required.