S water = J/gC
|
|
- Hope Bates
- 5 years ago
- Views:
Transcription
1 EXPERIMENT 7 Specific Heat Capacity of A Metal INTRODUCTION One of the properties of matter is that it requires a certain amount of heat energy to raise the temperature of a unit mass of a substance. This property is termed the heat capacity of a substance. If one measures the amount of heat needed to raise 1 gram of a substance 1 Celsius degree, this property is termed the specific heat capacity. For water, the specific heat capacity, S, is Joules per gram per Celsius degree, or S water = J/gC One of the properties of metals is that they are good conductors of heat. This means that metals have low specific heat capacities, and that it takes small amounts of heat energy to raise their temperatures. A heat transfer experiment is carried out within a well-insulated vessel known as a calorimeter. Because it is insulated, the calorimeter can effectively confine heat transferred during an experimental procedure. In the calorimeter, one substance will lose heat energy and another substance will gain heat energy. To differentiate between heat energy gained and heat energy lost, the following algebraic sign convention is used: heat energy gained by a substance is reported as positive, and heat energy lost by a substance is reported as negative. In this experiment we will find the specific heat capacity of an unknown metal. If a heated sample of hot metal is dropped into a calorimeter containing cool water, the metal will lose heat energy, causing the temperature of the metal to decrease, and the cool water will gain the heat energy from the metal, causing the temperature of the water increase. This process occurs unitl both the metal and the water reach the same intermediate temperature. The heat energy gained by the water in the calorimeter (Q water ) can be calculated from the specific heat capacity of the water solution (S water ), the mass of the water solution (m water ), and the change in temperature of the water solution ( T water ): Q water = S water m water Twater Because the water is gaining heat energy, Q water should be a positive value. For this to happen the change in temperature must be calculated as T = T final - T initial. If we assume that no heat energy escapes from the calorimeter, then the heat energy gained by the water must have come from the heat energy lost by the metal. Because the metal is losing heat energy, Q metal should be a negative value. Therefore, the heat energy lost by the metal (Q metal ) is equal in magnitude but opposite in sign to the heat energy gained by the water (Q water ): Q metal = -Q water 51
2 From the relationship for the metal: Q metal = S metal m metal T metal by knowing the heat energy lost by the metal (Qmetal), the specific heat capacity of the metal (S metal ) can be calculated from the mass of the metal (m metal ) and the change in temperature of the metal ( T metal ), where T = T final - T initial : S metal = Q metal m metal T metal PROCEDURE 1. Students will work individually for this experiment. Except for the laboratory handout, remove all books, purses, and such items from the laboratory bench top, and placed them in the storage area by the front door. For laboratory experiments you should be wearing closed-toe shoes. Tie back long hair, and do not wear long, dangling jewelry or clothes with loose and baggy sleeves. Open you lab locker. Put on your safety goggles, your lab coat, and gloves. 2. Place a clean, dry 250-mL beaker on a milligram balance. Tare the beaker by pressing one of the keys with the symbol " T/0 ". This will zero out the mass of the beaker. 2. Remove the beaker from the balance chamber, add about 25 g of metal pellets to the beaker, place it back on the balance, read the mass, and record it in your Data Table. CAUTION: Never transfer chemicals to a container that is on the pan in the balance chamber remove the container from the balance chamber, add the chemical, and then return the container to the pan in the balance chamber. 3. Attach an iron ring to a ring stand, and place a ceramic-centered wire gauze on the iron ring. Adjust the height of the iron ring so that when a laboratory burner is placed on the ring stand there is 5 cm of space between the top of the burner and the ceramic-centered wire gauze. Add about 400 ml of water to a 600-mL beaker, and place the beaker on the ceramic-centered wire gauze. Heat the water to boiling. 52
3 4. Pour the metal pellets into the extra large test tube. Obtain a 2-pronged clamp from drawer 022 at the back of the lab room and attach it the ring stand. Insert the extra large test tube through the 2-pronged clamp and into the beaker of boiling water. Carefully set the bottom of the extra large test tube on the bottom of the beaker. Do not tighten the 2-pronged clamp to the test tube; you want the test tube to be able to slide easily through the clamp. Have the 2-pronged clamp low enough so that at least 5 cm of test tube is exposed above it, as shown below. Heat the metal in the boiling water for 5 minutes. 5. While the metal pellets are in the boiling water, place a clean, dry 150-mL beaker on a milligram balance and tare its mass. Place about 50 to 60 ml of deionized water into the beaker, place it on the balance, read its mass, and record it as mass of calorimeter water in your Data Table. 53
4 6. Obtain three styrofoam cups and a lid from the box on the back counter. Place the three styrofoam cups in a 250-mL beaker for support as shown below. This is your calorimeter. Add the 50 to 60 ml of water to the top styrofoam cup, and using a thermometer measure the temperature of the water in the styrofoam cup. Record it in your Data Table as the initial temperature of calorimeter water. 7. Measure the temperature of the boiling water in the 600-mL beaker. The metal should now be at the same temperature, so record it in your Data Table as initial temperature of hot metal. Obtain a 3- pronged clamp from drawer 023 in the back of the lab room, and attach the 3-pronged clamp to the test tube above the 2-pronged clamp. Using the 3-pronged clamp as a handle, lift the test tube out of the boiling water and quickly pour the metal from the test tube into the top styroform cup. 8. Stir the water in the styrofoam cup with a stirring rod, then place the lid on the calorimeter and insert the thermometer into the water through a hole in the lid. Observe the temperature rise for several minutes, occasionally swirling the water, and record the maximum temperature the water achieves as the final temperature of calorimeter water and metal. 9. Empty the water from the calorimeter into the sink, and place the wet metal in the Pyrex casserole dish. Dry the Styrofoam cups and lid, and return the dry Styrofoam cups and lid to the box on the back counter. Do not throw them away. 10. Clean and wipe dry your laboratory work area and all apparatus. When you have completed your lab report have the instructor inspect your working area. Once your working area has been checked your lab report can then be turned in to the instructor. 54
5 EXPERIMENT 7 LAB REPORT Name: Student Lab Score: Date/Lab Start Time: Lab Station Number: DATA TABLE Mass of Metal. g Mass of Calorimeter Water. g Initial Temperature of Calorimeter Water. C Initial Temperature of Hot Metal. C Final Temperature of Calorimeter Water and Metal. C 1 Temperature Change of Calorimeter Water. C 2 Heat Gained by Calorimeter Water. J 3 Heat Lost by Metal. J 4 Temperature Change of Metal. C 5 Specific Heat Capacity of Metal. J/g C CALCULATIONS 1. 55
6
7
8 POSTLAB QUESTIONS 1. Calculate the number of joules of heat energy necessary to raise 250. g of water from 19.6 C to 65.4 C Box your answer. 2. Calculate the mass of a piece of copper that releases 545 joules of heat energy when cooled from C to 26.3 C. The specific heat capacity of copper is J/gC. Box your answer. 3. Find the specific heat capacity of an unknown metal if a 36.5 g sample at 99.6 C produces a resulting temperature of 25.0 C when placed in a calorimeter containing g of water at 20.2 C. Box your answer. 58
Laboratory Techniques
Name Skills Practice Lab Laboratory Techniques Date The best way to become familiar with chemical apparatus is to handle the pieces yourself in the laboratory. This experiment is divided into several parts
More informationStudent Lab Procedures. Lab Safety Orientation
Student Lab Procedures Lab Safety Orientation These basic rules should be followed by you & your students. The key to teaching lab safety is to role model it first. A class should be spent on: Location
More informationSafety Lab Goggles are required! Apron is optional!
Goggles are required! Apron is optional! Station 1: What would acid do to your eye? Materials: 6M hydrochloric acid, dropper, two petri dishes, egg whites. Procedure: 1. Separate the egg white from the
More informationInsulators and Conductors
Insulators and Conductors Materials that conduct, or transfer, heat well are called thermal conductors. A thermal conductor transfers heat well because of the way its particles are arranged. Particles
More information1. Conduct yourself in a responsible manner at all times in the laboratory.
LAB SAFETY GENERAL RULES 1. Conduct yourself in a responsible manner at all times in the laboratory. THIS INCLUDES: Staying OFF of your cell phone. Help your Lab Partners, don t just sit back and let them
More informationHEAT What are some sources of Heat?
HEAT Activity 1. Rub your hands quickly against each other. 2. Then quickly place them onto your face. 3. Describe what you feel. Your hands feel warm. 4. Why does it feel warm? It feels warm as HEAT has
More information1. Conduct yourself in a responsible manner at all times in the laboratory.
1. Conduct yourself in a responsible manner at all times in the laboratory. 2. Follow all written and verbal instructions carefully. If you do not understand a direction or part of a procedure, ask the
More informationTest Tube Rack. Test Tube
Equipment Cards Test Tube A test tube is a tube-shaped piece of glassware or plastic used for holding substances during experiments. Micro test tubes are smaller test tubes that reduce waste and expense.
More informationIGCSE PHYSICS GRADE 11 TERM 1 ASSESSMENT BOOKLET
PHYSICS IGCSE PHYSICS GRADE 11 TERM 1 ASSESSMENT BOOKLET 2013-2014 STS Page 1 of 44 PHYSICS PHYSI1101 ASSESSMENT TASK COVER PAGE Topic STS Performance Criteria Assessment event Date Time Thermal Physics
More informationliquid heating The density of the liquid changes as its temperature increases. This causes energy to be transferred throughout the liquid.
1 liquid is heated in a beaker. liquid heating The density of the liquid changes as its temperature increases. This causes energy to be transferred throughout the liquid. How does the density change and
More informationSTUDENT SAFETY RULES
STUDENT SAFETY RULES Purpose Science is a hands-on laboratory class. You will be doing many laboratory activities that require the use of hazardous chemicals. Safety in the science classroom is the #1
More informationMARIYA INTERNATIONAL SCHOOL AL-JUBAIL L-8 PHYSICS WORKSHEET(Heat & energy )
MARIYA INTERNATIONAL SCHOOL AL-JUBAIL L-8 PHYSICS WORKSHEET(Heat & energy ) 1 Name... (a)fig. Shows a thermometer with a range of 10 C to 50 C. Explain what is meant by (i) the sensitivity of a thermometer,......
More informationHeat can change into other forms of energy and vice versa. Heat is measured in the unit of energy, the joule (J).
ExamLearn.ie Heat Heat Heat has the ability to do work or move something. Thus, heat is a form of energy. Heat can change into other forms of energy and vice versa. Heat is measured in the unit of energy,
More informationI. C O N T E N T S T A N D A R D S
Introductory Physics, High School Learning Standards for a Full First-Year Course I. C O N T E N T S T A N D A R D S and radiation between objects or regions that are at different temperatures. 3.1 Explain
More information1. What are the scales of temperature? What are the formulas to convert among them? Fahrenheit, Celsius, Kelvin
-* Name Period 1. What are the scales of temperature? What are the formulas to convert among them? Fahrenheit, Celsius, Kelvin 2. Define Heat and temperature. Heat transfer of thermal energy from hotter
More informationLaboratory Equipment. Use of equipment
Laboratory Equipment Use of equipment 1 Please note that the name may not match exactly to your worksheet, therefore, match the picture from your worksheet to this power point. Safety goggles Used to protect
More informationBeakers hold solids or liquids that will not release gases when reacted or are unlikely to splatter if stirred or heated. Beaker
Lab Equipment Beakers hold solids or liquids that will not release gases when reacted or are unlikely to splatter if stirred or heated. Beaker Erlenmeyer Flask (Conical flask) Erlenmeyer flasks (conical
More informationScience Lab Safety Rules Katy Independent School District
Science Lab Safety Rules Katy Independent School District PURPOSE Science is a hands-on laboratory class. You will conduct laboratory activities which may require the use of hazardous chemicals or potentially
More informationName Science Period 1
Name Science Period 1 Table of Contents Getting Started 3 Safety Symbols 4 Animal Safety 5 Aprons 5 Breakage 6 Corrosive 7 Disposal 8 Electric 8 Flame 9 Fumes 10 General Safety Awareness 10 Gloves 11 Goggles
More informationLaboratory Equipment. Section 1L. Chemistry I & II
Laboratory Equipment Section 1L Chemistry I & II 1 Erlenmeyer Flask Used to contain liquids or solids that may release gases when mixed or heated. Narrow neck provides safety in case of splattering when
More informationElectric Circuits in Household Appliances
Electric Circuits in Household Appliances Topic Household appliances use simple electrical circuits. Introduction Household appliances contain electrical circuits. The circuit in any appliance contains
More informationUnit THE NATURE OF HEAT
Unit 5.0 - THE NATURE OF HEAT Heat is a form of energy, in the form of infrared radiation. Heat from the sun travels through space at the speed of 300,000,000 m/s. Upon arriving on earth, much of the radiant
More informationBefore Lab Work, Get to Know: Hazards of materials & agents and their prescribed safety procedures
Before Lab Work, Get to Know: Hazards of materials & agents and their prescribed safety procedures Also Get to Know: Emergency spill procedures. Handling equipment Location of fire ext., eye wash, shower,
More informationCHM 130LL: Lab Safety Name: Answer Key _ Section:
Introduction: CHM 130LL: Lab Safety Name: Answer Key _ Section: Safety in the chemistry laboratory is the primary concern of all scientists. Everyone who works in a chemistry lab is responsible for keeping
More informationBeakers hold solids or liquids that will not release gases when reacted or are unlikely to splatter if stirred or heated. Beaker
Lab Equipment Beakers hold solids or liquids that will not release gases when reacted or are unlikely to splatter if stirred or heated. Beaker Erlenmeyer Flask Erlenmeyer flasks hold solids or liquids
More informationUnit 21 Charles's Law. Procedure
Unit 21 Charles's Law Charles's Law was discovered by the French physicist, Jacques Charles in 1787 and can be simply stated as follows: OR: V1 V2 ---- = ---- T1 T2 V = kt In this experiment we will explore
More informationEffects of Wind on Plant Size
Effects of Wind on Plant Size Topic Wind has many effects on plant size. Introduction Scientists have found that plants raised in greenhouses have a tendency to be taller and thinner than their outdoor
More informationHeat and temperature. Making a thermometer
Heat and temperature A bout four hundred years ago, it would have been impossible to tell the temperature of the air, the water or any other substance. That s because there was no such thing as a thermometer
More informationLaboratory Techniques
Laboratory Techniques Procedure: Laboratory Burners. Essentially all single-barrel burners used in chemical laboratories are Bunsen burners or some modification of that burner that was invented by the
More informationLaboratory Techniques
Laboratory Techniques Procedure: Laboratory Burners. Essentially all single-barrel burners used in chemical laboratories are Bunsen burners or some modification of that burner that was invented by the
More informationLab Safety. General Safety Rules. General Safety Rules. Glassware Safety. General Safety Rules. General Safety Rules
Lab Safety 7. Roll up loose sleeves. 8. Know the location of the fire extinguisher, fire blanket, eyewash station, and first aid kit. 9. Keep your work area uncluttered. Take to the lab station only what
More informationGeneral Safety Rules
Lab Safety General Safety Rules 1. Listen to or read instructions carefully before attempting to do anything. 2. Wear safety goggles to protect your eyes from chemicals, heated materials, or things that
More informationThermal Properties and Temperature
Thermal Properties and Temperature Question Paper 5 Level IGCSE Subject Physics Exam Board CIE Topic Thermal Physics Sub-Topic Thermal Properties and Temperature Paper Type Alternative to Practical Booklet
More informationTransfer of Heat. There are three ways in which heat is transferred from one body to another. These are
Transfer of Heat In the precious chapter you have learnt that heat flows from a body at a higher temperature to a body at a lower temperature, but how does this transfer take place? You will find the answer
More informationChanges of State. Lesson 1
Lesson 1 Changes of State If all the ice in the world melted, the oceans would rise by more than 65 meters (215 feet)! This iceberg is melting in Paraiso Bay, Antarctica. What happens to ice when it melts?
More informationBeakers hold solids or liquids that will not release gases when reacted or are unlikely to splatter if stirred or heated. Beaker
Lab Equipment Beakers hold solids or liquids that will not release gases when reacted or are unlikely to splatter if stirred or heated. Beaker Erlenmeyer Flask Erlenmeyer flasks hold solids or liquids
More informationSafety In the Science Lab
Safety In the Science Lab Rules and Symbols Purwanti Widhy H Safety First Science is a hands-on laboratory class. You will be doing many laboratory activities, which require the use of hazardous chemicals
More informationA student investigated how much energy from the Sun was incident on the Earth s surface at her location.
A student investigated how much energy from the Sun was incident on the Earth s surface at her location. She put an insulated pan of water in direct sunlight and measured the time it took for the temperature
More informationThermal Energy Study Guide
Goal 1 Thermal Energy Study Guide Name: Hour Define the following in your own words: 1. Conductor - a material that allows heat to flow through it easily Two examples - metal pot, fork 2. Insulator - a
More informationBeakers hold solids or liquids that will not release gases when reacted or are unlikely to splatter if stirred or heated. Beaker
Lab Equipment Beakers hold solids or liquids that will not release gases when reacted or are unlikely to splatter if stirred or heated. Beaker Erlenmeyer Flask Erlenmeyer flasks hold solids or liquids
More informationGo to the Lab! Lab Safety Begins Before You
Lab Safety Lab Safety Begins Before You Go to the Lab! Science is a hands-on laboratory class. You will be doing many laboratory activities, which require the use of: Hazardous chemicals Expensive lab
More informationWhat is wrong with this picture?
Lab Safety What is wrong with this picture? General Safety Rules 1. Listen to or read instructions carefully before attempting to do anything. 2. Wear safety goggles to protect your eyes from chemicals,
More informationNCERT solution for Heat
NCERT solution for Heat 1 Question 1 State similarities and differences between the laboratory thermometer and the clinical thermometer. Similarities Both of them are made up of uniform glass tube Differences
More information2 Thermal Physics. Thermal Physics. 1. Simple kinetic molecular model of matter 2. Thermal properties 3. Transfer of thermal energy
2 Thermal Physics 1. Simple kinetic molecular model of matter 2. Thermal properties 3. Transfer of thermal energy 1. A swimmer climbs out of a swimming pool on a warm, dry day. Almost immediately he begins
More informationOverall Heat Transfer Coefficient for Double-Pipe Heat Exchanger
Overall Heat Transfer Coefficient for Double-Pipe Heat Exchanger Pre-laboratory Assignment Review the following: concept of the double-pipe heat exchanger, the overall heat transfer coefficient, logarithmic
More informationLab Safety and Equipment
Lab Safety and Equipment Name: Block: WHMIS Symbols WHMIS stands for Workplace Hazardous Materials Information System 1) Compressed 2) Flammable and Material 3) Material 4) Materials Causing and Serious
More informationHam & Cheese Muffins Connect Four
Safety & Sanitation Grade Levels: Middle School / High School Introductory Level Objective: Students will apply knowledge of safety and sanitation to food preparation skills. Resources: Classroom resources
More informationHeat and Specific Heat
Heat and Specific Heat A person puts a pan on a stove heating ring and returns a few seconds later to find that the pan is hot. The same person puts a pan of water on the stove ring and returns minutes
More information245 * Lab #4 Steam Distillation of Orange Oil
245 * Lab #4 Steam Distillation of Orange Oil In this experiment we will be extracting d-limonene (p-mentha-1,8-diene) by use of steam distillation. You want to be able to separate this natural product
More informationStarting with Safety American Chemical Society
Starting with Safety American Chemical Society Chemistry lab is different from most other courses. Here you gain new knowledge by doing things, not just reading about them. You ll spend much of your time
More informationISLAMAYA ENGLISH SCHOOL
1 (a) Some water is poured onto a plastic table-top, forming a puddle. The same volume of water is poured into a plastic dish, which is placed alongside the puddle. This is illustrated in Fig. 7.1. water
More informationBeaker Beakers hold solids or liquids that will not release gases when reacted or are unlikely to splatter if stirred or heated. Beakers are NOT accur
Lab Equipment Chemistry John T. Hoggard High School Mrs. Siddons Beaker Beakers hold solids or liquids that will not release gases when reacted or are unlikely to splatter if stirred or heated. Beakers
More informationChemistry Materials Separation Processes
Chemistry Materials Separation Processes You will be assigned to separate a mixture of several different materials. However, first you will need to learn about several techniques used for mixture separation.
More informationFamiliarize yourself with the following:
Lab Equipment Familiarize yourself with the following: 1. Know the names of the individual pieces of lab equipment. 2. Know the use of each piece. Note: Only limited explanations are provided in this slide
More informationScience Lab Equipment
Science Lab Equipment For exact volume measurements of liquids. Pipet on the left is a Volumetric pipet. It has only one graduation for delivering one exact volume. Pipet on the right is a Mohr pipet.
More information5L STAINLESS STEEL SLOW COOKER
5L STAINLESS STEEL SLOW COOKER PL390 Instruction Manual IMPORTANT SAFETY INSTRUCTIONS READ CAREFULLY AND KEEP FOR FUTURE REFERENCE Carefully read this manual before using this appliance. Ensure that you
More informationLab Safety. Section 2L. Chemistry I & II
Lab Safety Section 2L Chemistry I & II 1 Lab Safety Topics General Rules Clothing Accidents and Injuries Handling Chemicals Handling Glassware and Equipment Heating Substances First Aid 2 General Rules
More informationModels Goldfisch Fat Extraction Apparatus
Models 3500100 Goldfisch Fat Extraction Apparatus Copyright 2017 Labconco Corporation. The information contained in this manual and the accompanying products are copyrighted and all rights reserved by
More informationWhat percentage of infra red is absorbed by the glass? increases. does not change. decreases. Blacksurfaces are poor emitters of infra red radiation.
Q1. (a) Infra red radiation can be reflected, absorbed and transmitted by glass. (i) What percentage of infra red is absorbed by the glass?... (ii) Complete the following sentence by drawing a ring around
More informationLab Safety presentation and contract first day of lab know the locations of everything in your lab no student can participate in class without signed
Lab Safety presentation and contract first day of lab know the locations of everything in your lab no student can participate in class without signed contract Lab inspections Safety Office will be randomly
More information(1) ... (2) Each strip has a negative charge. The cloth is left with a... charge. This is because particles called... have been transferred
Q1. A student did an experiment with two strips of polythene. She held the strips together at one end. She rubbed down one strip with a dry cloth. Then she rubbed down the other strip with the dry cloth.
More informationDIRT! APES Laboratory Activity
Name: Part I: Soil Texture DIRT! APES Laboratory Activity Can one determine the texture of soil by examining the particles found in a particular sample? The purpose of this activity is to determine the
More informationPHYS 1405 Conceptual Physics I Heat and Temperature
PHYS 1405 Conceptual Physics I Heat and Temperature Materials Laptop LabPro Heat Pulser Immersion Heater Stainless temperature probe Styrofoam cup, large Styrofoam cup, small Introduction In this activity
More informationFire and burn safety at home
Fire and burn safety at home Safe signals in the home Kitchen safety Bathroom safety Bedroom safety Living area safety Storage or utility safety Smoke and carbon monoxide detectors Doors and windows Fire
More informationSafety In Chemistry. Identified Risks and Hazards
Safety In Chemistry ] Introduction Students have a duty of care to minimize and eliminate chemical risk and hazards through proper use of laboratory equipment and to be prudent of potential dangers associated
More informationState of Nevada Department of Transportation Materials Division METHOD OF TEST FOR EVALUATING CLEANNESS OF COARSE AGGREGATE
State of Nevada Department of Transportation Materials Division METHOD OF TEST FOR EVALUATING CLEANNESS OF COARSE AGGREGATE SCOPE The cleanness test provides an indication of the relative proportions of
More informationActivity Sheet Chapter 2, Lesson 1 Heat, Temperature, and Conduction
Activity Sheet Chapter 2, Lesson 1 Heat, Temperature, and Conduction Name Date In this activity, you will place a room-temperature set of washers in hot water and then place a set of hot washers in room-temperature
More informationS2 Science. Heat. Homework Booklet
S2 Science Heat Homework Booklet 1 1. The graph below shows how most substances cool after being taken away from the source of heat. Answer these questions about the graph a. where is the heat loss the
More informationST. GABRIEL S SECONDARY SCHOOL Lower Secondary Science Chapter 7 Transfer of Thermal Energy
ST. GRIEL S SEONRY SHOOL Lower Secondary Science hapter 7 Transfer of Thermal Energy Worksheet 7.1 Name : _Suggested nswers ( ) lass : ate : Section : Multiple hoice Questions 1 Two similarly-sized blocks,
More informationKeep It Hot! Handout
Keep It Hot! Handout Day 1: Introduction Today, you will study heat transfer by conduction and convection! Fill in the rest of these statements: Heat is Heat always flows from to If we heat up a material
More informationSt. Anthony's Canossian Secondary School Sec 3E Science (Physics) Chapter 9 Transfer of Thermal Energy. Name: ( ) Class: Sec Date:
St. Anthony's Canossian Secondary School Sec 3E Science (Physics) Chapter 9 Transfer of Thermal Energy Name: ( ) Class: Sec Date: Candidates should be able to: (a) show understanding that thermal energy
More informationMODEL# GPM630 PASTA MAKER HOMEMADE PASTA. PHOTO OF PRODUCT
MODEL# GPM630 PASTA MAKER HOMEMADE PASTA www.gourmia.com PHOTO OF PRODUCT 2016 Gourmia www.gourmia.com Welcome to Indulgence of Homemade Pasta Maker from Gourmia! The Steelstone Group Brooklyn, NY Fresh,
More informationState of Nevada Department of Transportation Materials Division METHOD OF TEST FOR EVALUATING CLEANNESS OF COARSE AGGREGATE
State of Nevada Department of Transportation Materials Division Test Method Nev. T228C METHOD OF TEST FOR EVALUATING CLEANNESS OF COARSE AGGREGATE SCOPE The cleanness test provides an indication of the
More informationExperiment 4: Purification of Liquids by Distillation
Experiment 4: Purification of Liquids by Distillation A. Distillation Procedure: In this experiment, you will perform a fractional distillation on a solution comprised of a 50-50 mixture of n-butyl acetate
More informationCentrifuge STANDARD OPERATING PROCEDURE
STANDARD OPERATING PROCEDURE Centrifuge Model: Sorvall, RC-5B Plus Manufacturer: Kendro Laboratory Products Location: Technology Transfer Lab, 1568 Food Sciences Building Publication Date: 09/26/2014 Iowa
More informationThermal Energy Worksheets
Thermal Energy Worksheets Say Thanks to the Authors Click http://www.ck12.org/saythanks (No sign in required) To access a customizable version of this book, as well as other interactive content, visit
More informationHEAT TRANSFER. The tips of both brass rods are held in the gas flame. Mark each of the following as True or False.
HEAT TRANSFER Refer to the following information for the next four questions. The tips of both brass rods are held in the gas flame. Mark each of the following as or. 1. Heat is conducted only along Rod
More information6. Within an internal combustion engine, the can-shaped component that moves up and down the cylinder
Student ID: 22133336 Exam: 986052RR - Heat When you have completed your exam and reviewed your answers, click Submit Exam. Answers will not be recorded until you hit Submit Exam. If you need to exit before
More information(a) (i) Through which part of the house is most heat lost? How can the heat loss through the windows be reduced? ...
Q1. The diagram shows where heat is lost from a house that is not insulated. (a) (i) Through which part of the house is most heat lost? (ii) How can the heat loss through the windows be reduced? (b) A
More information3B Heat, Light and Sound
Heat, Light and Sound Heat, light and sound are forms of energy that have many applications in our lives. Heat Heat is a form of energy When petrol burns in a car engine it causes the gases in the cylinders
More information6 th Grade Conduction, Convection, and Stored Heat Energy
6 th Grade Conduction, Convection, and Stored Heat Energy Summary: Students feel convection by melting an ice cube in their hands. They layer cold water, room temperature water, and hot water in a clear
More informationINSTANT HOT WATER DISPENSER
INSTANT HOT WATER DISPENSER Tank Installation Materials required (not provided) 2 mounting bracket screws (and 2 plastic anchors if attaching to drywall) Shut-Off valve and T fitting Components When you
More informationLaboratory SAFETY RULES
Laboratory SAFETY RULES All chemistry students must successfully pass a test on the following material before they are allowed to work in the laboratory. The test consists of 20 multiple choice questions.
More informationMCDB4100: LABORATORY SAFETY GUIDELINES
MCDB4100: LABORATORY SAFETY GUIDELINES Dress code for the lab session Exposed skin is a risk for contact with hazardous materials. For your protection, you must dress properly for each laboratory session.
More informationDifferent energy sources can be used to generate electricity.
Q1. Electricity is a useful form of energy. (a) Different energy sources can be used to generate electricity. Give one advantage and one disadvantage (other than cost) of using each energy source to generate
More informationAPPENDIX A: MICROSCALE APPARATUS AND TECHNIQUES A.1 CRAIG TUBES: RECRYSTALLIZATION
APPENDIX A: MICROSCALE APPARATUS AND TECHNIQUES This Chapter describes and illustrates the apparatus and microscale techniques that are used in the experiments you will perform but are not necessarily
More informationStandard Operating Procedure for Oil & Grease Method EPA1664A
Standard Operating Procedure for Oil & Grease Method EPA1664A This document is intended to enable a technician new to Solid Phase Extraction (SPE) technology to perform SPE on oil and grease samples while
More informationSt. Anthony's Canossian Secondary School Sec 3NA Science (Physics) Chapter 7 Transfer of Thermal Energy. Name: ( ) Class: Sec Date:
St. Anthony's Canossian Secondary School Sec 3NA Science (Physics) Chapter 7 Transfer of Thermal Energy Name: ( ) Class: Sec Date: Candidates should be able to: (a) show understanding that thermal energy
More informationSafety In the Science Lab
Lab Safety: Everyone Is Responsible! Safety In the Science Lab Rules and Symbols Mrs. Mork Greenville Middle School Safety First Science is a hands-on laboratory class. You will be doing many laboratory
More informationManual Page 1 of 8. Manual. Laboratory autoclave
Manual 17.11.2014 Page 1 of 8 Manual Laboratory autoclave Autoclave using steam for the treatment of material and laboratory processes e.g. sterilization, as an aid in research and development CertoClav
More information36" Drum Plug Aerator OWNER S MANUAL
36" Drum Plug Aerator OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationMagnetic Stirring Systems with Heat
Sharing your passion for making jewelry. Products. Service. Know-how. Magnetic Stirring Systems with Heat 335-212 Digital Ceramic Magnetic Stirring System with Heated Stand 335-211 Ceramic Magnetic Stirring
More informationSection 9. Comparing Energy Consumption: More for Your Money. What Do You See? What Do You Think? Investigate. Learning Outcomes
Section 9 Comparing Energy Consumption: More for Your Money Section 9 Comparing Energy Consumption: More for Your Money What Do You See? Learning Outcomes In this section, you will Measure and compare
More informationFigure 1. Explain how rubbing an acetate rod with a cloth causes the rod and cloth to become charged
Q1.A student rubs an acetate rod with a cloth. Figure 1 shows the charges on the acetate rod and cloth before and after rubbing. Figure 1 (a) Explain how rubbing an acetate rod with a cloth causes the
More informationMill, Ultra-Centrifugal STANDARD OPERATING PROCEDURE
STANDARD OPERATING PROCEDURE Mill, Ultra-Centrifugal Model: ZM-1 Manufacturer: Retsch GmbH & Co. KG Location: Dry Processing Pilot Plant, 1851 Food Sciences Building Publication Date: 08/29/2014 Iowa State
More informationenergy from hot flame [3] [2]
1 This question is about energy transfer and how it is used in cooking. (a) Steve heats a pan of water on his cooker. Look at the diagram. water aluminium base energy from hot flame (i) Explain how the
More informationEffects of Different Media on Plant Growth. Materials and Methods
Effects of Different Media on Plant Growth A. Nony Mouse Biology 356 Instructor: Dr. Jim Barron Lab 10: Plant Lab Lab Partners: Charles Darwin Gregor Mendel James Watson Materials and Methods In late October-early
More informationFreezing (solid), Melting (liquid), Evaporation (gas) Study Presentation INCLUDING WATER STATE CHANGE GRAPHS
Freezing (solid), Melting (liquid), Evaporation (gas) Study Presentation INCLUDING WATER STATE CHANGE GRAPHS Lesson Vocabulary 1. Melting- solids gain heat and change into liquids 2. Freezing- liquids
More informationFundamentals of Heat Transfer
Fundamentals of Heat Transfer State basic laws of heat transfer Estimate heat transfer rates by different modes Use the concept of thermal resistance to solve steady state heat transfer problems State
More informationThe table gives information about some ways of reducing the energy consumption in a house. Installation cost in. Fit a new hot water boiler
## (a) The table gives information about some ways of reducing the energy consumption in a house. Method of reducing energy consumption Installation cost in Annual saving on energy bills in Fit a new hot
More information