Standard Specifications
|
|
- Florence Robbins
- 5 years ago
- Views:
Transcription
1 Organic Pollution Monitor (UV Meter) OPM-6 The OPM-6 is one of our latest models, and represents the culmination of more than three decades of product development and field experience. This model is an organic pollution monitor (UV meter) that employs ultraviolet absorptiometry to analyze the organic pollution levels in commercial, industrial, and other types of effluents. The values obtained are correlated with the CODMn, and are then used to calculate the pollution load and other items in accordance with the Total Effluent Control System. Before using the instrument, make a correlation between the instrument output and the CODMn. The design of this meter applies the measurement principle and method stipulated in the JIS K 87 standard, Ultraviolet photometer for monitoring of water pollution. Features Compact and lightweight design The immersion-type detector included with the instrument, which was highly rated by users of the previous model, has been made approximately 5% smaller and % lighter than the original detector, making it much easier to install the instrument. In addition, the installation of the optional sample receiving tank enables measurements to be performed by extracting samples from the process stream. New optical system A new highly stable light source ensures that the unit provides stable measurements. The new optical system employs a power-saving lamp and eliminates the need for a heater to stabilize the light source. These two factors help to significantly reduce the amount of power consumed by the instrument (approximately 8% less than the previous model). Furthermore, additional power savings is also possible by using an immersion-type detector that does not require a sample pump system. Standard Specifications Product name Model Object measured Measurement method Measurement range Measurement cell Cell cleaning Sample Condition Maximum water depth : Organic Pollution Monitor (UV meter) : OPM-6 : Organic pollution in commercial, industrial, and other types of effluents : Dual-wavelength absorptiometry (UV 54nm/visible light 66nm) : UV absorbance; ~.5Abs (The transmission output range can be adjusted in. Abs increments within a range of.5~.5abs.) The readings can be displayed as absorbance on a mm cell length conversion basis. The displayable absorbance ranges are as follows. 5 mm cell; ~.Abs mm cell; ~.5Abs 6 mm cell; ~4.7Abs : Immersed parallel cell (6,, or 5mm, as specified by customer) : Wiper system for automatic cleaning Cleaning cycle; ~9999 minutes (default; 6) No. of cleaning; ~99 (default; ) : Sample temperature; ~45 C (no freezing) Flow speed (Immersion type); Lower.75m/sec. (Notes of Installation on Page of 7 and 9) Flow rate(sampling type); ~6 L/min. :6m
2 Calibration Displayable item Transmission output Contact output signals Contact input signals Digital communication output (optional feature) : Zero; Pure water Span; Potassium hydrogen phthalate solution (A calibration vessel is supplied as a standard accessory.) : UV-VIS absorbance, UV absorbance, VIS absorbance, COD conversion value, Turbidity conversion value, SS (Suspended Solid) concentration conversion value and sample temperature. : 4~mADC, load resistance; 6Ω or less, isolated Simultaneously output of any three of the following signals; UV-VIS absorbance, UV absorbance, VIS absorbance, COD conversion value, turbidity conversion value, SS concentration conversion value, and sample temperature (non-isolated between transmission outputs). The COD conversion value, turbidity conversion value, and SS concentration conversion value are calculated by employing a linear expression to convert the absorbance. : Power cut-off signal, c contact (NO/NC) output Alarm signal, a contact (NO) output (Any three of the following contacts can be selected.) Under maintenance Under cleaning General alarms Measured value higher limit alarm Lamp error (UV, VIS) No sample Leakage alarm Wiper drive motor error Sample temperature error In addition to the first three items listed above, any three of the six general alarm items can be assigned to contact outputs ~. Contact capacity; VDC,.A or less 5VAC,.A or less (resistance load) : Cleaning start signal; Signal used to remotely control the cleaning program. No-voltage contact signal ON resistance; 5Ω or less Short circuit current; Maximum of 5mA Open voltage; 4VDC Make time;.sec. or more : Two selections are available for digital communication output; communication output RS-485 or output to USB memory for data recording. Digital communication output; RS-485 interface USB memory (data is saved in CSV format) Memory data format; date-hour-minute, UV, VIS, and UV-VIS values, COD conversion value, turbidity conversion Power requirements Power consumption Mounting Materials Surface finish Protective construction Transmitter cable port Extension cable Dimensions (see the section Dimensions for details) Weight Installation Related equipment value, SS concentration conversion value, water temperature (sampling cycle can be set to a length of to 99 minutes) An approximately five year block of data can be saved when minute is specified as the sampling cycle. If the amount of available free space becomes incredibly low, the unit will be unable to record new data. Make sure to delete old or unnecessary data at regular intervals. : ~4VAC±%, 5/6Hz : Average of approx. VA, maximum of approx. VA : Immersed type, wind-up type, hanging type, and sampling type : Transmitter; Die-cast aluminum ; Main body SUS6, ABS resin Cell Quartz glass Wiper FPM rubber : Transmitter; Metallic silver : Transmitter; IP65 : Six cable glands for ø6~ cable (one of which is for the detector) Conduit threads (six G/ threads) can be connected when the cable glands are removed. : cable to connect the detector and transmitter Standard length; Sampling type m. Immersed type, wind-up type, and hanging type; Specified by customer Maximum length; m (optional feature) : Transmitter; Approx. 8 (W) x (D) x 8 (H) mm ; Approx. 5 (W) x (D) x 455 (H) mm The height (H) of the immersed type varies according to the specification. :Transmitter; Approx..kg ; Approx. 5.kg(except cable) : Unit can be installed outdoors Ambient temperature; -5~5 C Ambient humidity (transmitter); % RH or less Ensure the unit is not subjected to vibration, shock, and corrosive gases. Install the detector at a position in which the sample water can circulate smoothly. This will ensure that the readings accurately reflect the sample values. : Load calculator The load calculator CALD- is recommended for determining the cumulative load. --
3 Performance UV absorptiometry linearity : Within ±%FS UV absorptiometry repeatability : Within ±%FS UV absorptiometry zero drift : Within ±%FS/week UV absorptiometry span drift : Within ±%FS/week Response rate : Within sec. for 9% response Typical CODMn conversion value by cell length Cell length COD value (mg/l) 5mm ~5 mm 5~ 6mm ~5 Immersed parallel cell (6,, or 5 mm, as specified by customer) Operating principle Measurement cell Low-pressure mercury lamp UV detector UV detector Feedback Feedback VIS detector VIS detector LED The OPM-6 uses the dual wavelength technique to measure pollutants. This technique employs two highly stable sources of light, UV (ultraviolet) and VIS (visual light). When a UV light source is applied, a 54nm emission line from the ozone-free low pressure mercury lamp is used. In VIS detection, a pulsating 66nm LED is irradiated as the light source. There are two ways for converting instrument output to COD values. The first consists of using the correlation the between UV absorbance (AUV) and the COD manual analysis value. The second method entails using the correlation between the difference of the UV absorbance (AUV) minus VIS absorbance (AVIS) (value given by the expression AUV - a x AVIS to eliminate the effect of suspended solids) and the COD manual analysis value. a= Correction factor (Freely specified value of ~9.9. Default value of..) --
4 Terminal connections Any three of the following six items can be assigned to contact outputs ~: Transmission output Transmission output A B C A B C Transmitter D D 8 E E 8 Power cut-off output RS-485 I/O NC COM NO 9 9 E E Power supply Transmission output NO NO NO UV value (Abs) VIS value (Abs) UV-VIS value (Abs) COD conversion value Turbidity conversion value SS concentration conversion value Cleaning start input 4VDC output Contact output Contact output Contact output Terminal screw size: M Dedicated connector is used for connecting between the detector and transmitter. The 4VDC output is synchronized with the wiper cleaning for future function. Do not connect anything to this terminal now. Under maintenance Under cleaning General alarm Measured value upper limit alarm Lamp error No sample Leakage alarm Wiper drive motor error Sample temperature error In addition to the first three items listed above, any three of the six general alarm items can be assigned to contact outputs ~. Dimensions Unit : mm Mounted on a pole Mounted on a wall or rack 8 8 (7) 64 (7) (4) () Display Mounting holes for hood Operation keys 8 Display Cable entries (5) 5A pipe (5) 8 Operation keys 8 Cable entries 4-ø5.8 4 () Inner pressure regulating valve Grounding terminal Six cable entries (Cable glands for ø6~ cable) Hood (optional) Recommended when installing the instrument outdoors at a location exposed to direct sunlight. Material : SUS4 Mounting : 5A pipe or wall Code number : 7499K Inner pressure regulating valve Grounding terminal Six cable entries (Cable glands for ø6~ cable) -4-
5 Dimensions Unit : mm Immersed type detector Extension cable ø Wind-up type detector ( guide pipe system) ( guide pipe system) Zinc anode Zinc anode Extension cable Eye bolt(m6) (54) (455) 47 ø6.5 Guide (455) Hanging type detector 45 Sampling type detector Extension cable Eye bolt(m6) (455) Holder 5 Extension cable ø.7(t) ø L+5 L+4 (54) ø6.5 Eye bolt(m6) Guide 4 Zinc anode ø6.5 Cable (54) ø6.5 (54) (455) 47 Zinc anode Zinc anode
6 Installation diagram Immersed type.frame mounting dimensions.frame dimensions Maintenance clearance and anchor bolt positions Transmitter 5 or more 6± 65 or more Front face M x 5 Unit : mm Anchor bolt mounting dimensions 7 or more 6± 5 or more (6) Power cable CVV:.5 sq ~ sq, -core Finishing diameter: ø6 ~ Transmission output cable CVV:.5 sq ~ sq, -core Finishing diameter: ø6 ~ Contact signal cable CVV:.5 sq ~ sq, ~ -core Finishing diameter: ø8 ~ RS-485 digital communication signal CPEV-S, -core Finishing diameter: ø6 ~ Grounding (Class D) mounting bracket or more 6 Power supply, signal line Pole stand (optional feature) edicated cable for detector ow sufficient length detector maintenance. Immersed type detector tector mounting bracket Lower end of the mounting bracket 5 or less Flow Transmitter Six cable entries (Cable glands for ø6~ cable) Installation example Greater than the length of the detector Obstacle(at the top) Flow velocity:.75 m/sec or less X = minimum dimension: or greater than the length of the detector Y = minimum dimension: or greater than the length of the detector Notes: ) Make sure the detector is properly installed so that it can be drawn up for maintenance safely and easily. Firmly secure the detector, taking into consideration the force exerted on the bottom of the detector by the flow velocity and the physical weight of the detector itself. Sample flow velocity condition:.75m/sec or less ) Make sure to allow for sufficient space so that the detector can be installed. An amount of space greater than the length of the detector in the horizontal or vertical direction for maintenance clearance is recommended. (See the diagram.) ) Install the detector in at least mm of water. 4) Make sure the length of the extension cable between detector and transmitter (included as accessory) is sufficient. This ensures that the detector can be drawn up easily for maintenance. In addition, make sure to place the extension cable well away from sources of noise and interference, such as power lines. 5) The instrument must be grounded at a grounding resistance of less than Ω (Class D), separate from the power grounding. 6) Make sure to install an earth leakage breaker on the power line. 7) The shape of the pole stand and mounting bracket for the detector vary, depending on the specifications. For details, see the supplied specifications. For detectors with a length of less than 5mm, a single set of mounting brackets is supplied. For detectors with a length more than 5mm, two sets of brackets are supplied. In addition, when the flow velocity exceeds.5m/sec, make sure to use two sets of brackets to firmly secure the immersed type detector. 8) When specifying the orientation of the detector in relation to its length, make sure to consider the flow velocity and circulation of the sample water. -6-
7 Product code Immersed type -7- OPM6-- A B Custom specification code: Numeric digit: 9 Alphabet: Z A B C D 8 Transmitter mounting 5A pipe Wall Digital output None RS-485 USB memory Arrester (power line/transmission line) None Included Hood for transmitter (sun shade) None (standard) Equipped cell length 5mm mm 6mm Installation No pole stand Pole stand (ZB--B: SUS4) mounting * Immersed type,.m-length (one set of mounting brackets included) Immersed type,.5m-length (one set of mounting brackets included) Immersed type,.m-length (two sets of mounting brackets included) * Immersed type,.5m-length (two sets of mounting brackets included) * Zinc anodes * N/A Equipped Cable length (between transmitter and detector) 5m m Custom spec. (max. m) Markings Japanese (standard) English *. The condition of the sample water flow velocity for the immersed type must be.75m/sec or less. Make sure the length between the bottom of the mounting bracket and the top of the detector does not exceed.5m. In this case, use two sets of brackets to secure the detector. When the sample water flow velocity is.5m/sec or less, make sure the length between the bottom of the mounting bracket and the top of the detector does not exceed.m. This case also requires the use of two sets of brackets to secure the detector. When the sample water flow velocity exceeds.75m/sec, install a dam or similar obstacle in the stream to lower the flow velocity. *. When the detector length is.m or more, use two sets of mounting brackets. *. If the water sample becomes contaminated, with sea water for example, it can result in the introduction of a high concentration of electrolytes or residual iron-based coagulants into the sample. This may increase the possibility of the detector rusting away rapidly. If that is the case, select Equipped for Zinc anodes. Also select Equipped for the Zinc anodes section when you replace existing equipment that already has zinc anodes equipped. Notes : The transmission output range can be adjusted in.abs increments within a range of.5~.5abs. In the default factory configuration, the output signals for ~.Abs are output at between 4~mA, regardless of the cell length. : The user can select whether the absorbance is Displayed or Not displayed on a mm cell length conversion basis. In the factory default configuration, the absorbance is Not displayed on a mm cell length conversion basis. : The unit is powered by an adjustable-voltage ~4VAC power supply. 4: Any three of the following output signals can be selected: UV-VIS absorbance, UV absorbance, VIS absorbance, COD conversion value, turbidity conversion value, SS concentration conversion value, and sample temperature (4~mADC). 5: When you replace existing equipment, the specifications for alarm contact output and other items for this unit might differ from the old unit. For details, please contact one of our sales representatives.
8 Installation diagram Unit : mm Wind-up type/hanging type. Frame dimensions Transmitter (6) Power cable CVV:.5 sq ~ sq, -core Finishing diameter: ø6 ~ Transmission output cable CVV-S:.5 sq ~ sq, -core Finishing diameter: ø6 ~ Contact signal cable CVV-S:.5 sq ~ sq, ~ -core Finishing diameter: ø8 ~ RS-485 digital communication signal CPEV-S, -core Finishing diameter: ø6 ~ Grounding (Class D).Frame mounting dimensions Maintenance clearance and anchor bolt positions 5 or more 6± 5 or more M x 5 4-ø5 Front face Anchor bolt mounting dimensions 7 or more 6± 5 or more.wind-up device mounting dimensions Anchor bolt position Bulkhead Water surface (-guide pipe system) Frame 4-ø5 6 Wind-up device Winch 75 5± (75) 5 (Anchor bolt position) (57) 5 stopper Guide pipe fixing bracket Wind-up device dimensions Example: Using m guide pipe Notes: When using the stainless steel winch, the handle and fixing positions are symmetric. Mark (for setting the frame) Guide pipe Wire rope (5) 5 6±5.5 (Anchor bolt position) 8± (45) 6 (maintenance clearance) 6 () Stopper pin 75 ± (When using the stainless steel winch) (48) M x (44) 5± 75 (65) 8± (8) Fixing the guide pipe (-guide pipe system): Use a fixing bracket to attach the guide pipe to the wall of the bulkhead, as shown below. Bulkhead M x Anchor bolt mounting dimensions ø~ 5 ø.7 (I.D. approx. ) Stopper (M5 bolt) Fixing bracket (-guide pipe system) Winch ø7. Mark (for setting the frame) Hanging type (5) Stopper pin Frame Guide pipe Wire rope 5 6±5.5 4-ø5 (57) 75 5± (75) 5 (Anchor bolt position) 5 () (Anchor bolt position) 8± (45) 6 (maintenance clearance) mm or more ø7. stopper Secure a sufficient height level to avoid dirtying the detector with mud. 9 7 Hanging type detector -8-
9 Product code Wind-up type/hanging type -9- OPM6-- A B Custom specification code: Numeric digit: 9 Alphabet: Z E F G H J K L M N P Q 8 Transmitter mounting 5A pipe Wall Digital output None RS-485 USB memory Arrester (power line/transmission line) None Included Hood for transmitter (sun shade) None (standard) Equipped cell length 5 mm mm 6 mm Installation No pole stand Pole stand (ZB--B: SUS4) mounting * Wind-up device ( guide pipe system), m * Wind-up device ( guide pipe system), m * Wind-up device ( guide pipe system), 4m * Wind-up device ( guide pipe system), m * Wind-up device ( guide pipe system), m * Wind-up device ( guide pipe system), 4m * Wind-up device ( guide pipe system), 5m * Wind-up device ( guide pipe system), 6m * Use existing wind-up device ( guide pipe system) * Use existing wind-up device ( guide pipe system) * Hanging type (two.5m chains included) *4 Zinc anodes *5 N/A Equipped Cable length (between transmitter and detector) 5m m Custom spec. (max. m) Markings Japanese (standard) English *. The condition of the sample water flow velocity for the wind-up device ( guide pipe system) must be.75 m/sec or less. When the flow velocity exceeds.m/sec, make sure to secure the lower end of the guide pipe before using the device. (See the installation diagram.) *. The wind-up device ( guide pipe system) must be used at a flow velocity of.m/sec or less. Make sure to secure the guide pipes at multiple points along the pipes and at the lower end before using the device. The frame of the wind-up device is made of SUS4 (coated). In custom specifications, a winch made of SUS can be selected. However, the position of the handle is reversed left to right. (Same for * and *) *. The existing wind-up device for OPM-4 / OPM-4A is used for mounting the detector. *4. The recommended method for simple installation is using two.5m chains to lower the detector. (Two eye bolts are supplied with the detector when this method is used.) The flow velocity must be.75m/sec or less. *5. If the water sample becomes contaminated, with sea water for example, it can result in the introduction of a high concentration of electrolytes or residual iron-based coagulants into the sample. This may increase the possibility of the detector rusting away rapidly. If that is the case, select Equipped for Zinc anodes. Also select Equipped for the Zinc anodes section when you replace existing equipment that already has zinc anodes equipped. Notes : The transmission output range can be adjusted in.abs increments within a range of.5~.5abs. In the default factory configuration, the output signals for ~.Abs are output at between 4~mA, regardless of the cell length. : The user can select whether the absorbance is Displayed or Not displayed on a mm cell length conversion basis. In the factory default configuration, the absorbance is Not displayed on a mm cell length conversion basis. : The unit is powered by an adjustable-voltage ~4VAC power supply. 4: Any three of the following output signals can be selected: UV-VIS absorbance, UV absorbance, VIS absorbance, COD conversion value, turbidity conversion value, SS concentration conversion value, and sample temperature (4~mADC). 5: When you replace existing equipment, the specifications for alarm contact output and other items for this unit might differ from the old unit. For details, please contact one of our sales representatives.
10 Installation diagram Unit : mm Sampling type (mounted on pole stand) Transmitter Power cable WR: CVV;.5 sq ~ sq, -core Finishing diameter: ø6 ~ Transmission output cable WR: CVV-S;.5 sq ~ sq, -core Finishing diameter: ø6 ~ Contact signal cable WR: CVV-S;.5 sq ~ sq, ~ -core Finishing diameter: ø8 ~ RS485 digital communication signal CPEV-S, -core Finishing diameter: ø6 ~ 5 or more 5± 5 or more 4-ø4 5 or more 45± Mx 65 Anchor bolt mounting dimensions Grounding (Class D) Front face Maintenance clearance 7 or more (5) Sample receiving tank Pole base Wire hose band Braid hose (ø5xøxm) Sample receiving tank Ball valve By-pass valve Flow rate regulating valve (~6L/min) VP Coupling system Braid hose (øxø8xm) Front Drain Pipe image Sampling pump (self-suction type) Sample Strainer (5- mesh) Sampling type (mounted on aluminum frame) Transmitter Power cable WR: CVV;.5 sq ~ sq, -core Finishing diameter: ø6 ~ Transmission output cable WR: CVV-S;.5 sq ~ sq, -core Finishing diameter: ø6 ~ Contact signal cable WR: CVV-S;.5 sq ~ sq, ~ -core Finishing diameter: ø8 ~ RS485 digital communication signal CPEV-S, -core Finishing diameter: ø6 ~ 5 or more ± 5 or more 4 -ø4 5 or more 4± Mx 65 Anchor bolt mounting dimensions Grounding (Class D) 9 Front face Maintenance clearance 7 or more (5) Calibration vessel Sample receiving tank
11 Product code Sampling type -- OPM6-- A B Custom specification code: Numeric digit: 9 Alphabet: Z R 8 Transmitter mounting 5A pipe N/A Digital output None RS-485 USB memory Arrester (power line/transmission line) None Included Hood for transmitter (sun shade) None (standard) Equipped cell length 5mm mm 6mm Installation Pole stand with sample receiving tank (B5--C: SUS4) * Aluminum frame * mounting Sampling type Zinc anodes * N/A Equipped Cable length (between transmitter and detector) m (standard length for sampling type) Custom spec. (max. m) Markings Japanese (standard) English *. A calibration vessel is equipped as a standard. *. The aluminum frame has the same dimensions as the base of our previous models (OPM-4 and OPM-4A). Thus, the frame of a previously released instrument can be used to replace the frame of this new instrument. *. If the water sample becomes contaminated, with sea water for example, it can result in the introduction of a high concentration of electrolytes or residual iron-based coagulants into the sample. This may increase the possibility of the detector rusting away rapidly. If that is the case, select Equipped for Zinc anodes. Also select Equipped for the Zinc anodes section when you replace existing equipment that already has zinc anodes equipped. Notes : The transmission output range can be adjusted in. Abs increments within a range of.5~.5abs. In the default factory configuration, the output signals for ~. Abs are output at between 4~mA, regardless of the cell length. : The user can select whether the absorbance is Displayed or Not displayed on a mm cell length conversion basis. In the factory default configuration, the absorbance is Not displayed on a mm cell length conversion basis. : The unit is powered by an adjustable-voltage ~4VAC power supply. 4: Any three of the following output signals can be selected: UV-VIS absorbance, UV absorbance, VIS absorbance, COD conversion value, turbidity conversion value, SS concentration conversion value, and sample temperature (4~mADC). 5: When you replace existing equipment, the specifications for alarm contact output and other items for this unit might differ from the old unit. For details, please contact one of our sales representatives.
12 International Operations: DKK-TOA Corporation 9-, -Chome, Takadanobaba, Shinjuku-ku, Tokyo Japan Tel : Fax : Information and specifications are subject to change without nofice. Issued on //5
Standard Specifications
Organic Pollution Monitor (UV Meter) OPM-6 The OPM-6 is one of our latest models, and represents the culmination of more than three decades of product development and field experience. This model is an
SPECIFICATION SHEET ORGANIC POLLUTION MONITOR. Model: OPM-410A - Organic Pollution Monitor - Issue: OPM-410A-0107-R0 Page 1 ISO ISO-9001
ISO-14001 ISO-9001 SPECIFICATION SHEET ORGANIC POLLUTION MONITOR Model: OPM-410A The Model OPM-410A monitors organic pollution in water from industrial effluent, rivers etc.. The design and construction
OIL FILM DETECTOR (Long-distance correspondence Version)
OIL FILM DETECTOR (Long-distance correspondence Version) ODL-6A The Model ODL-6A monitors a water surface for the presence of an oil film floating on the surface. The instrument projects a laser beam onto
OIL FILM DETECTOR (Flame-proof Version) SODL-1600
OIL FILM DETECTOR (Flame-proof Version) SODL-600 The model SODL-600 is a flame-proof type oil film detector. This model monitors a water surface for the presence of an oil film floating on the surface.
Features. Drop-in type detector
SUSPNDD SOIDS NYZR Model SSF-6 The SSF-6 is an analyzer used to conduct continuous optical measurements of the concentration of solids. It can measure the concentration of suspended solids (SS) in sewage,
SPECIFICATION SHEET. SLC-1615 (for low concentration) SLC-1625 (for high concentration) SILICA ANALYZER
ISO-14001 ISO-9001 SPECIFICATION SHEET SILICA ANALYZER Model: SLC-1605 (for very low concentration) SLC-1615 (for low concentration) SLC-1625 (for high concentration) This equipment is used for high accuracy
Mercury Vapor Monitor VM-3000
Member of the envea Group Mercury Vapor Monitor VM-3000 Continuous mercury measurement in air and other gases Direct reading mercury vapor meter Proven reliable detection method: UV absorption (CVAAS)
General Specifications
eneral Specifications DO70 Optical Dissolved Oxygen Sensor EERA DO70 optical dissolved oxygen sensor is designed for using in water treatment plants such as sewage treatment works and effluent activated
VM-3000 Mercury Vapor Monitor
MERCURY INSTRUMENTS Analytical Technologies VM-3000 Mercury Vapor Monitor Continuous mercury measurement in air and other gases Direct reading mercury vapor meter Proven reliable detection method: UV absorption
PUV, PIR and PFO Series BROCHURE
PUV, PIR and PFO Series BROCHURE JUNHO 2013 ABB Multiwave TM process photometers PUV3402, PIR3502 and PFO3372 Measure vapor and liquid samples in IR, NIR, UV and VIS regions Process photometers PUV3402,
OPTISENS TUR 2000 Technical Datasheet
OPTISENS TUR 2000 Technical Datasheet Sensor for turbidity measurement in water and wastewater Rugged design for harsh applications Integrated transmitter with direct 4...20 ma output Near infrared light
INSTRUCTION MANUAL. DECKMA HAMBURG GmbH. Type OMD-12. Oil-in-Water Monitor
INSTRUCTION MANUAL Oil-in-Water Monitor Type OMD-12 DECKMA HAMBURG GmbH Kieler Straße 316, D-22525 Hamburg Tel.: ++49 40 54 88 76-0, Fax: ++49 40 54 88 76-10, email: post@deckma.com IMPORTANT NOTICE Replacement
General Specifications
General Specifications Model DM8 Vibration Type Liquid Density Meter Overview In 1967, YOKOGAWA developed the Model VD6 Vibration Type Liquid Density Meter in response to user requests for an online density
Model Q45P/R. ph/orp Monitor...
Model Q45P/R ph/orp Monitor... Sensor Mounting Configurations The Differential Difference ORP Monitor ATI's versatile Q45P/R ph/orp system is designed for use in all industrial and municipal applications.
Class 1 laser beam sensor safe for your eyes
113 Sensor SERIES Related Information General terms and conditions... F-7 About laser beam... P.199~ Sensor selection guide... P.1~ General precautions... P.11 PHOTO PHOTO PARTICUR MEASURE ITY panasonic.net/id/pidsx/global
Model Q45P/R. ph/orp Monitor...
Model Q45P/R ph/orp Monitor... Sensor Mounting Configurations The Differential Difference ORP Monitor ATI's versatile Q45P/R ph/orp system is designed for use in all industrial and municipal applications.
Class 1 laser beam sensor safe for your eyes
1129 PHOTO PHOTO PARTICUR Sensor SERIES Related Information General terms and conditions... F-3 About laser beam... P.193~ guide... P.121~ General precautions... P.19 Conforming to FDA regulations (-11
Ventostat Wall Mount. Amphenol Advanced Sensors. Telaire Wall Mount CO 2. , Humidity and Temperature Transmitters. Features:
Ventostat Wall Mount Telaire Wall Mount, Humidity and Temperature Transmitters Features: Patented, Absorption Infrared Gas sensing engine provides high accuracy in a compact low cost package. Patented
Class 1 laser beam sensor safe for your eyes
13 Sensor SERIES Related Information General terms and conditions... F-17 About laser beam... P.13~ Sensor selection guide... P.967~ General precautions... P.1 PHOTO PHOTO Conforming to EMC Directive Conforming
VM-3000 Mercury Vapor Monitor
MERCURY INSTRUMENTS ANALYTICAL TECHNOLOGIES VM-3000 Mercury Vapor Monitor Continuous mercury measurement in air and other gases Direct reading mercury vapor meter Portable, integrated battery for 6 hours
SIMRAD GD10 IR GAS DETECTOR
1 SIMRAD GD10 IR GAS DETECTOR Operating Manual 5th Edition P3359E October 1999 1 CONTENTS Section Page 1. PRODUCT DESCRIPTION 3 1.1 General description 3 1.2 Construction 3 1.3 Application areas 4 1.4
Specifications. Table of contents. 2:Specification. 3:Composition. 4:Instruments outside figure
DUST DENSITY METER (DDM-2001) Specifications Table of contents 1:Outline 2:Specification 3:Composition 4:Instruments outside figure 1) Main body control box 2) Detector 3) Optical fiber cable 4) Purge
SIMRAD GD10PE IR GAS DETECTOR
SIMRAD GD10PE IR GAS DETECTOR Operating Manual P3404E 1st edition Jan. 2004 www.simrad-optronics.com CONTENTS 1. PRODUCT DESCRIPTION... 5 1.1 General description... 5 1.2 Construction... 5 1.3 Application
UV I UNIT030W / UV I UNIT055W
016W 030W / 055W 110W 220W UV Systems Assembly and Operating Instructions Water we re in our Element www.intewa.de Table of Contents 1. General Information... 2 2. Safety Precautions... 2 3. Dimensioning...
AUR300C. Advanced Ultraviolet Burner Controller
No. CP-SS-1807E AUR300C Advanced Ultraviolet Burner Controller Overview The AUR300C is a burner controller with a dynamic selfchecking function and is used in combination with the AUD300C or AUD500C Advanced
Contents. Outline of Product. Features of Product. Specifications of Product. Name and central function of section. Illustration of Terminal
DA-750 1 page Contents Outline of Product 3 page Features of Product 3 page Specifications of Product 4 page Name and central function of section 5 page Illustration of Terminal 8 page Setting of Menu
Scanning Laser Range Finder Smart-URG mini UST-10LN Specification
Date: 2016.3.24 Scanning Laser Range Finder Smart-URG mini UST-10LN Specification Symbol Amended Reason Pages Date Corrector Amendment No Approved by Checked by Drawn by Designed by UST-10LN Specification
AUR300C, AUR350C. Advanced Ultraviolet Burner Controller
No. CP-SS-7E Overview The AUR300C is a burner controller with a dynamic selfchecking function and is used in combination with the AUD300C or AUD00C Advanced Ultraviolet Flame Detector. This AUR300C controls
SIMRAD GD10P - IR GAS DETECTOR OPERATING MANUAL
SIMRAD GD10P - IR GAS DETECTOR OPERATING MANUAL P3359E 8th edition - November 2005 Simrad Optronics ASA Kabelgaten 4B P.O. Box 174, Økern NO-0509 OSLO, NORWAY Phone +47 22 66 60 00 Fax +47 22 66 60 01
PRODUCT SPECIFICATIONS
( 様式 ) PRODUCT SPECIFICATIONS OZONE MONITOR MODEL EG-700E Published on August 07, 2015 EBARA JITSUGYO CO., LTD. MEASURING INSTRUMENT AND MEDICAL DIVISION MEASURING INSTRUMENT SALES DEPARTMENT EAST JAPAN
A New Standard of Excellence
A New Standard of Excellence PREVENTION IS SO EASY... LIVING THROUGH A DISASTER IS NOT The reliable identification of low combustion oxygen in a fired heater or boiler has always been critical to the effectiveness
English. Series. Installation and Use Manual
English Series FOSTER Installation and Use Manual FOSTER Rev.13 03/2015 MITECH srl reserves the right to change the information in this document without warning. Index Anti-intrusion barrier 3 Main components
Model gffoz Process Ozone Sensor (In-Line)
Date ECO# Rev Description Originator 9/15/97 1.0 First Publication DB 10/8/97 2.0 Miscelaneous corrections DB 10/28/97 3.0 Minor changes BM 5/1/98 3.1 Added CE compliance BM TM IN USA, INCORPORATED 87
Zirconia Oxygen Gas Analyzers
Fuji Instrumentation & Control Fuji Electric s Direct Insertion Type Zirconia Oxygen Gas Analyzers ZIRCOMAT-P ZIRCOMAT-C Detctor No sampling device is required Compact and light
Q-Series Relative Humidity and Relative Humidity & Temperature Sensors for Critical Environments and Outdoor Air
Document No. 155-755 Q-Series Relative Humidity and Relative Humidity & Temperature Sensors for Critical Environments and Outdoor Air Description Features Application The Q-Series Relative Humidity and
Series Temperature Controller Instruction Sheet
Series Temperature Controller Instruction Sheet Thank you very much for purchasing DELTA A Series. Please read this instruction sheet before using your A series to ensure proper operation and please keep
Advanced Ultraviolet Burner Controller
No. CP-SS-7E Advanced Ultraviolet Burner Controller Model AUR300C/AUR30C Overview The AUR300C Advanced Ultraviolet Burner Controller and AUR30C Advanced Ultraviolet Burner Controller with Communication
Technical Information OUSAF44
TI00416C/07/EN/13.16 71316935 Products Solutions Services Technical Information Optical sensor combined with the OUA260 flow assembly for the measurement of UV absorption Application The sensor measures
Dust Concentration Meter
Dust Concentration Meter To Sense Breaks or Tears in Filter Bags, to Improve Product Quality, and to Eliminate related Environmental and Safety Risks Triboelectric Dust Monitor Particles in the air are
Model 6650SP. Filber Optic-Based UV-Fluorescence Oil-in-Water Analyzer
Model 6650SP Filber Optic-Based UV-Fluorescence Oil-in-Water Analyzer 6650SP - OVERVIEW The Model 6650SP is the next generation in-water Analyzer. The 6650SP incorporates the most advanced, state-of-the-art
APS-S/M Series. Polycarbonate Resin Square Type, 2-wire/3-wire DC System. Type. Proximity Sensor. Features
Sensor INFORMATI Series Features Polycarbonate Resin, -wire/-wire DC System - Front Surface / Upper Surface detection - s of different frequency are available for adjacent installation. - Conformity with
VM-702B ABSOLUTE VIBRATION MONITOR MODULE Page 1 of 5
Page 1 of 5 No entry if additional Model Code / Additional Spec. Code ( spec. code is not specified. ) VM-702B /ALY /NB1 /CS1 /CS2 /TRP /TB Analysis Function Non-incendive * 1 Monitor Function Analysis
OX100, OX102. Limiting-current type Oxygen Analyzer OX100, OX102. Bulletin 11M10A01-03E
Limiting-current type Oxygen Analyzer OX00, OX02 OX00, OX02 Limiting-current type Oxygen Analyzer One Instrument measures 00 ppm to 25% Oxygen Simple "One Touch" Calibration Self Diagnostics Assure High
CLARITY II TURBIDIMETER
Product Data Sheet PDS 71-T1055/rev.J January 2006 Model T1055 CLARITY II TURBIDIMETER COMPLETE SYSTEM includes single or dual input analyzer, sensor(s), and debubbler assembly CHOOSE U.S. EPA METHOD 180.1
Smart Transmitter/ Gas Detector Head
PT2E-1760 Smart Transmitter/ Gas Detector Head SD-1EC Operating Manual (PT2-176) Safety information -04 Specific conditions of use - The plastic window is submitted to tests corresponding
Dew Point Mirror 373. High Precision. Fast Response. Wide Measuring Range. Laboratory Reference. Touch Screen. Full Color High Resolution LCD
Dew Point Mirror 373 High Precision Fast Response Wide Measuring Range Laboratory Reference Touch Screen Full Color High Resolution LCD Chilled Mirror Hygrometry Chilled mirror hygrometry, a process used
IN-SITU ZIRCONIA OXYGEN ANALYZER
IN-SITU IRCONIA OXYGEN ANALYER DATA SHEET FK8, KM, TA This oxygen analyzer is used to continuously measure oxygen concentration in combustible exhaust gas of industrial boilers or furnaces, and is ideally
Compact Ultra Low Temperature Chamber
Compact Ultra Low Temperature Chamber MC-712R 812R CAT.NO.E14140-Z1804 High performance and reliability come in a compact package, covers wide range of temperature testing needs, from ultra-low temperature
ANALOX SENSOR TECHNOLOGY LTD ANALOX DD1101 INSTALLATION & OPERATION MANUAL
ANALOX SENSOR TECHNOLOGY LTD ANALOX DD1101 INSTALLATION & OPERATION MANUAL SAFETY WARNING Please Refer to the Safety Warning in Section 7.1 regarding the chemicals in the oxygen sensor Analox Sensor Technology
Series 5000 Hydrazine Analyzer Model 60002
Series 5000 Hydrazine Analyzer Model 60002 T he patented* Series 5000 Hydrazine Analyzer is a continuous-reading instrument using the p-dimethylaminobenzaldehyde method of analysis for colorimetric measurement
Technical Information OUSTF10
TI00500C/07/EN/01.13 71157320 Products Solutions Services Technical Information Optical sensor combined with flow assembly OUA260 for measurement of turbidity and non-dissolved solids Application The scattered
SEC SIGNATURE ETO MONITOR TRAINING SENSOR ELECTRONICS CORPORATION
SEC SIGNATURE ETO MONITOR TRAINING SENSOR ELECTRONICS CORPORATION SEC SIGNATURE ETO MONITOR SIGETO1420597 PRODUCT INTRODUCED TO ETHYLENE OXIDE STERILIZATION INDUSTRY IN 2001. OVER 850 UNITS IN FIELD WORLDWIDE
AS950 ALL-WEATHER REFRIGERATED SAMPLERS
AS950 ALL-WEATHER REFRIGERATED SAMPLERS Applications Wastewater Collections Industrial Pretreatment Environmental Monitoring Stormwater Sampling has never been this easy. The AS950 All-Weather Refrigerated
S304 and S305 Dust Emission Monitors. User Manual. Distributor
S304 and S305 Dust Emission Monitors User Manual Distributor Version 6.4 30/5/2012 Table of Contents 1. INTRODUCTION... 3 1.1 Safety... 3 1.2 Product overview... 4 1.3 Principle of operation... 4 2. INSTALLATION...
Technical Information OUSTF10
TI00500C/07/EN/02.16 71316944 Products Solutions Services Technical Information OUSTF10 Optical sensor with the OUA260 flow assembly for the measurement of turbidity and undissolved solids Application
AquaLynx 200 ADX. Monitoring and Control System. Background. Operation
AquaLynx 200 ADX Monitoring and Control System The RODI Systems AquaLynx 200 ADX is a unique monitoring system for water treatment applications. The AquaLynx 200 ADX offers a dependable yet affordable
SAMPLE MANUAL - INSTALLATION - FOR REFERENCE ONLY. ChemScan mini Analyzer. Parameter. Method #### Installation, Operation & Maintenance Manual
Parameter Method ####, Operation & Maintenance Manual Rev 3/26/2018 Contact Information Document Information Customer Name: Plant Name/Location: Date: Analyzer Serial #: ASA, Inc. (Applied Spectrometry
Temperature Controllers
Model TEC-4100 1/4 DIN Model TEC-4100 1/4 DIN Temperature Controller Ordering Code: Power Input BOX 1 4 = 90-250 VAC 5 = 11-26 VAC / VDC TEC-4100- Configurable for 4 Programmable Outputs and NEMA 4X/IP65
General Specifications
General Specifications GS J0H-0E Model MVHK Digital Limit Alarm (DC Type) with Active Color PV Display General This plug-in type Digital Limit Alarm for DC input receives DC current or DC voltage signal.
Installation Instructions
0908HN50 Lossnay Energy Recovery Ventilator Model: LGH-50RSDC-E (0-0V 50Hz) Installation Instructions (For use by dealer/contractor) Contents Safety precautions... Outline drawings... Standard installation
Ventostat Wall Mount. Telaire Wall Mount CO 2. , Humidity and Temperature Transmitters. GE Sensing & Inspection Technologies.
GE Sensing & Inspection Technologies Ventostat Wall Mount Telaire Wall Mount, Humidity and Temperature Transmitters Features: Patented, Absorption Infrared Gas sensing engine provides high accuracy in
Hygro/hygrothermal transducers (hygrometric)
Data Sheet 90.7031 Page 1/7 Hygro/hygrothermal transducers (hygrometric) for measuring relative humidity and temperature for mounting indoors, outdoors, and in air ducts with resistance, current or voltage
Ventostat Wall Mount. Telaire Wall Mount CO 2. , Humidity and Temperature Transmitters. GE Sensing & Inspection Technologies.
GE Sensing & Inspection Technologies Ventostat Wall Mount Telaire Wall Mount, Humidity and Temperature Transmitters Features: Patented, Absorption Infrared Gas sensing engine provides high accuracy in
IN-SITU ZIRCONIA OXYGEN ANALYZER
IN-SITU IRCONIA OXYGEN ANALYER DATA SHEET FK8, KM, TA This oxygen analyzer is used to continuously measure oxygen concentration in combustible exhaust gas of industrial boilers or furnaces, and is ideally
Ultrasonic Reflective Sensor
Ultrasonic Reflective with an Adjustable Sensing Distance of 0.3 to 3 m Under Stable Operation without Background Interference Ensures a stable operating range with minimal side-lobe areas. Built-in unstable
Hygro/hygrothermal transducers (hygrometric)
Data Sheet 907031 Page 1/7 Hygro/hygrothermal transducers (hygrometric) for measuring relative humidity and temperature for mounting indoors, outdoors, and in air ducts with resistance, current or voltage
Constant climate chambers
KBF series (E5.2) Constant climate chambers Constant climate chambers The BINDER KBF is the specialist for unconditionally reliable stability testing and precise maintenance of constant climatic conditions.
OX100/OX102. Limiting-current type Oxygen Analyzer. Bulletin 11M10A01-03E
/ Oxygen Analyzer Bulletin MA-3E A Compact Environmental Oxygen Anal yzer with the usual Yokogawa reliability MODEL MODEL Alarm Calibration keys holder: 7 mm (* ) dia. or G3/8 Plastic sensor holder (Specify
IN-SITU ZIRCONIA OXYGEN ANALYZER <HART communication>
DATA SHEET IN-SITU ZIRCONIA OXYGEN ANALYZER ZFK8, ZKM-2, ZTA This oxygen analyzer is used to continuously measure oxygen concentration in combustion exhaust gas of industrial boilers
SCM. Micro. Streaming Current Monitor. Analyzer. Sensor/Sampler with light shield removed. The Analyzer. Instrument Overview
Micro SCM Streaming Current Monitor A Watts Water Technologies Company Instrument Overview The instrument consists of the Analyzer and the SCM sensor. Analyzer The Analyzer The monitor has a built in graphic
General Specifications
General Specifications Model OX400 Low Concentration Zirconia Oxygen Analyzer The OX400 is a highly accurate and reliable low-concentration zirconia oxygen analyzer that is capable of measuring a wide
Specifications Wavelength Range: 190 nm to 800 nm continuous
www.ietltd.com Proudly serving laboratories worldwide since 1979 CALL 001.847.913.0777 for Certified, Refurbished Lab Equipment Thermo Finnigan Surveyor PDA Detector Specifications Wavelength Range: 190
WIO200 Water In Oil measuring instrument
WIO200 Water In Oil measuring instrument You have made the right decision by choosing a measuring instrument from PAJ Systemteknik. Many customers buy our high standard products every year. There are at
TR FLEXMAG 4050 C Electromagnetic flow meter for single use processes
TR 2017-03-06 FLEXMAG 4050 C Electromagnetic flow meter for single use processes 1. Introduction 2. Measuring principle 3. The FLEXMAG 4050 versions 4. Target applications 5. Technical Data FLEXMAG 4050
APPLIED. OMA-300 Hydrogen Sulfide Analyzer H 2. Ex p. Ex d. The world s safest continuous H 2. S analyzer. The OMA continuously measures H 2
H 2 S Ex p Ex d The world s safest continuous H 2 S analyzer. The OMA continuously measures H 2 S concentration using a full-spectrum UV-Vis spectrophotometer, harvesting the power of collateral data to
SAMPLE SPECIFICATIONS CONTINUOUS MONITORING SYSTEM (Insitu)
PART 1 - GENERAL A. RELATED DOCUMENTS SAMPLE SPECIFICATIONS CONTINUOUS MONITORING SYSTEM (Insitu) Federal, State, and local requirements as applicable. Attached Permit Attached drawings B. SUMMARY 1. Provide
Improve Performance and Reduce Maintenance Costs. Model Q45D. Dissolved Oxygen Monitor...
Improve Performance and Reduce Maintenance Costs Model Q45D Dissolved Oxygen Monitor... Why Throw Away Money? Why Throw Away Money? ATI s Model Q45D Dissolved Oxygen monitor is designed to provide reliable
NORTH AMERICAN ADVANCED TECHNOLOGIES, INC.
NORTH AMERICAN ADVANCED TECHNOLOGIES, INC. WSS-W Core-extractable protective bimetal thermometer (Adjustable angle, Back, Bottom Connected) WSSX-W Gear style core-extractable protective bimetal thermometer
Bristol Babcock Oil Content Monitor "oil in water"
NORTHEAST CONTROLS INC. ONLINE www.nciweb.net 123 Pleasant Avenue - Upper Saddle River - New Jersey 07458 USA Tel: 201-327-7660 / Fax: 201-327-3242 Bristol Babcock Oil Content Monitor "oil in water" General
Turbimax CUE21 / CUE22
Technical Information Turbimax CUE21 / CUE22 Turbidimeter for on-line measurement Application On-line continuous monitoring of clean water: Drinking water Treated process water Your benefits Versions with
Analyze IT Zirconia Oxygen Analyzer for Small Boiler Applications
Data Sheet Analyze IT Zirconia Oxygen Analyzer for Small Boiler Applications Ideal for small gas/oil fired boilers Cost effective solution for OEM outlets with a quick return on end-user investment Continuous
Communications None RS-232C RS-422* RS-485* BCD Transmission output*/** (4 to 20 ma) E5AX- E5AX- L(M)A02 L(M)A03
Digital Controller A 96 x 96-mm (DIN) Digital Process Controller Optimum PID control with feed-forward control circuitry. High accuracy (+0.3% FS +1 digit max.). Replaceable Output Units. Models with communications
CMT MANUAL 6. NMC SENSORS
CMT MANUAL 6. NMC SENSORS TABLE OF CONTENTS INDEMNITY... 5 DOCUMENT INFORMATION... 5 ACKNOWLEDGEMENTS... 5 6.1 INTRODUCTION... 6 6.2 TEMPERATURE AND HUMIDITY SENSORS... 7 6.2.1. TEMPERATURE SENSOR... 7
SPECIFICATIONS PARTICLE SENSOR KS-41B Higashimotomachi, Kokubunji, Tokyo , Japan
SPECIFICATIONS PARTICLE SENSOR KS-41B 3-20-41 Higashimotomachi, Kokubunji, Tokyo 185-8533, Japan No. 11025-4E 18-01 Printed in Japan Outline The KS-41B is a sensor which uses the light scattering method
A measured step forward
A measured step forward Operations & Maintenance Manual TM JESCO UV 405-412-440-450-480-550-80 2 LCD LCD PLUS Contents 1. Introduction...3 2. General Principles and Safety Instructions...4 3. Instructions
Constant climate chambers
KBF series (E5.2) Constant climate chambers Constant climate chambers The BINDER KBF is the specialist for unconditionally reliable stability testing and precise maintenance of constant climatic conditions.
Low-Power Detectors. Key Features. 818 Series. Power levels from pw to 2W. Wavelengths from 190 nm to 1800 nm. Proprietary detector optics
818 Series TUTORIAL SPECTRUM ANALYZER HIGH-POWER DETECTORS INTEGRATING SPHERES LOW-POWER DETECTORS POWER & ENERGY METERS Key Features Power levels from pw to 2W Wavelengths from 190 nm to 1800 nm Proprietary
Ultrasonic Reflective Sensor
Ultrasonic Reflective with an Adjustable Sensing Distance of 0.3 to 3 m Under Stable Operation without Background Interference Ensures a stable operating range with minimal side-lobe areas. Built-in unstable
Color Mark Sensor. Sensing gdsa distance Spot diameter e. Possible to switch between vertical or horizontal connection using the M12 rotary connector.
Color Mark Sensor Detects laminated or light-dispersing objects in stable operation without being influenced by mirror reflection. Double indication of the detection level and threshold level allows easy
AMERICAN AIR & WATER, INC.
CC HIGH OUTPUT UV COIL CLEANERS CC Series High-Output UV systems are designed specifically for HVAC applications. They can be mounted in various configurations to irradiate cooling coils and drain pans
Advance Optima Module Magnos 17
Advance Optima Module Magnos 17 Service Manual 43/24-1002-0 EN Table of Contents Page Chapter 1: Description of functions 1-1 Chapter 2: Module variants and components 2-1 Chapter 3: Analyzer variants
Flostop TS D7E and A8E. Operation Manual
Flostop TS D7E and A8E Operation Manual United Kingdom Spectron Gas Control Systems Ltd, Unit 4, ATU1, University of Warwick science Park, Coventry, +44 (0) 24 7641 6234 sales@spectron-gcs.com Germany
Series 3300 TELEDYNE ANALYTICAL INSTRUMENTS. The 3300 series of low cost, microprocessorbased
TELEDYNE Series 3300 Unaffected by hydrocarbons, H2, or CO2 Easy to handle, inexpensive, and easy to replace Can apply to ppb, ppm, and percent ranges Trace & Percent Oxygen Analyzers Fuel Cell Zirconium
SEC Signature Process Gas Analyzer
SEC Signature Process Gas Analyzer Instruction and Operation Manual Sensor Electronics Corporation 5500 Lincoln Drive Minneapolis, Minnesota 55436 USA (952) 938-9486 Fax (952) 938-9617 email sensor@minn.net
Series 155. Mass Flow Computers TECHNICAL SPECIFICATIONS
TECHNICAL SPECIFICATIONS Mass Flow Computers Series 155 The Kurz 155 Mass Flow Computer is a versatile system transmitter that integrates the functions of flow and temperature measurement, flow totalization,
Bionics Instrument. Alarm Handling. Gas Alarm Systems
Gas Alarm Systems Controllers and PLC based systems Alarm Handling Complete control at the right time and place Every gas detector consist of a gas sensor and a signal transmitter. In case of a gas leak,
Flame Monitor for Multiple Burner Furnaces D-LE 603 D-UG 660
Selectivity Adjustable by Means of - High Pass Frequency Filter - Gain - Threshold Different Adjustments for Different Conditions (e.g. According Fuel or Combustion Technology) Possible, to be Activated
STT 3000 Series STT250 Smart Temperature Transmitters Specifications Models STT25T EN0l-6091 February 2009
STT 3000 Series STT250 Smart Temperature Transmitters Specifications Models STT25T EN0l-6091 February 2009 Introduction Honeywell s STT 3000 family of microprocessor based transmitters covers the full
Dräger Polytron Pulsar 2 Open Path Gas Detector
Dräger Polytron Pulsar 2 Open Path Gas Detector The Dräger Polytron Pulsar 2 represents the latest infrared technology in open path gas detection. Equipped with all the same functions as the standard Dräger
DF-340E PROCESS ANALYZERS APPLICATIONS FEATURES
PROCESS ANALYZERS DF-340E The DF-340E is a Coulometric sensor based oxygen analyzer suitable for outdoor installation and designed to measure trace oxygen and percent level in pure and multigas backgrounds.