ES SERIES SURGICAL SCRUB SINKS

Transcription

1 ES SERIES SURGICAL SCRUB SINKS INSTALLATION OPERATION MAINTENANCE USER MANUAL California OSHPD Pre-approved Mac Medical, Inc. 820 South Mulberry Street Millstadt, Illinois (618) phone (618) fax MAN-009 Rev. - August, 2014

2 WARNINGS AND CAUTIONS Following is a list of the safety precautions, which must be observed when operating this equipment. WARNINGS indicate the potential for danger to personnel, and CAUTIONS indicate the potential for damage to equipment. These precautions are repeated (in whole or in part), where applicable, throughout the manual. It is important to review these precautions before using the equipment. WARNING-INJURY HAZARD: REPAIRS AND ADJUSTMENTS should be only attempted by experienced mechanics fully acquainted with this equipment. Use of inexperienced, unqualified persons to work on the equipment, or the installation of unauthorized parts, could cause serious personal injury, or result in costly damage. NOTE - TWO PEOPLE ARE REQUIRED to mount the sink to the wall. WARNING-BURN HAZARD: ANY REPAIR or modification of mixing valve may affect the high temperature setting. The installer must check operating temperature before sink is back in operation. CAUTION-POSSIBLED EQUIPMENT DAMAGE: When cleaning the sink, use a non-abrasive polish. Rub in a back and forth motion in the same direction of the surface grain.

3 GENERAL SPECIFICATIONS 1. MATERIAL: SINK BASIN: 14 GAUGE, 304 STAINLESS STEEL SINK SKIRT: 18 GAUGE, 304 STAINLESS STEEL 2. ALL PLUMBING ½ COPPER OR BRASS PIPE. 3. UTILITY REQUIREMENTS: COLD WATER: 20 TO 50 PSIG 70 DEG F MAX HOT WATER: 20 TO 50 PSIG 120 DEG F TO 140 DEG F IT SHALL BE THE CUSTOMERS RESPONSIBILITY TO INSURE BY USE OF PRESSURE REGULATORS, OR OTHER MEANS, THAT MAXIMUM SPECIFIED PRESSURES ARE NOT EXCEEDED. WATER LINES SHOULD BE FLUSHED CLEAN BEFORE WATER CONNECTIONS ARE MADE. IT SHALL BE THE CUSTOMERS RESPONSIBILITY TO ENSURE THAT WATER SUPPLIES ARE PROPERLY PROTECTED FOR INTERNAL CROSS CONNECTION CONTROL IN ACCORDANCE WITH LOCAL BUILDING AND PLUMBING REQUIREMENTS. IT SHALL BE THE CUSTOMERS RESPONSIBILITY TO ELIMINATE WATER HAMMER CONDITIONS SHOULD THEY OCCUR IN THE SERVICE PIPING. 4. POWER REQUIREMENTS (FOR SENSOR OPERATIONS): 120 VOLT, 60 Hz, SINGLE PHASE, 15 AMP GFIC PROTECTED ELECTRICAL OUTLET (BY OTHERS), INSTALLED PER LOCAL BUILDING CODES. 5. NET WEIGHT OF SINK IS 110 LBS SINGLE BASIN, 189 LBS DOUBLE BASIN, and 330 LBS TRIPLE BASIN. 6. SINK IS UL AND CUL RECOGNIZED. 7. SINK IS CALIFORNIA OSHPD PRE-APPROVED WHEN MOUNTED ON A STRUCTUALLY SOUND WALL.

4 Installation 1. Carefully uncrate the scrub sink. The mounting hardware is under the sink, secured to the shipping materials. Be sure to remove all hardware before discarding packaging. 2. Install Z bracket(s) to the wall. Recommended mounting specifications shown in FIG #1 for ES25, and FIG #2 for ES47 (see page 4). NOTE: For wall mounted units the wall structure must be capable of supporting the load. 3. Install sink support brackets. HINT: With the help of an assistant, hang the sink from the Z bracket(s). With the sink in place mark the proper position for the brackets. Remove the sink and finish installation of the brackets. 4. Check supply and waste terminal location. Be sure all connections are safely accessible and in proper working condition. (See supply location dia. Page 5) NOTE: For proper sink operation the hot water temperature must be 120 deg. F. 5. Install the soap spout (See page 6). 6. Install the sink body. With the help of an assistant slide the sink back down over the Z bracket(s) until it locks securely into place.

5 FIG #1 - ES25 FIG #2 - ES47

6 Water Pressure After the plumbing installation is complete, the water pressure can be adjusted to avoid excess splash. The pressure can be controlled by adjusting the flow (flow control valve). See the plumbing diagram to find the correct location of the valve depending on sink type. Plumbing Diagram Infra Red Self-Activated Sinks Manual Knee Operated Sinks

7 Infra Red Controls Installation: The sink is supplied with a 24V power transformer that connects to a standard duplex outlet (110/120V outlet required). Plug the transformer into the outlet. A red led will flash in the sensor window. It is important to not interrupt the sensor beam until the light turns off. Operation: The sensors are pre set and equipped with a logic board. The sensor determines the range during initialization period (The time after initial power until the light turns off. Approximately 5 minutes). The range is approximately in front of the sensor, and is 25 degrees at peak. During the initialization period, the sensor allows for fixed objects that may be within the sensors range. The sensors are equipped with a 2 second on/off delay, and no time out feature. This prevents the sink from turning on when walking past at a normal pace and no time out allows for an uninterrupted scrub. Soap Dispenser Install Replacement Parts Item No. Description Part No. 1 Thermostatic Mixing Valve S Infra Red Sensor S Flow Control Valve S Knee Operated Water Valve S Spout S Solenoid Valve for Infra Red 7 Soap Pump Kit 8 Swivel Aerator S0089 NOT SHOWN S0028 NOT SHOWN S0032 NOT SHOWN To prevent damage, the soap dispenser is stored inside the sink basin during shipping. The dispenser head should be installed before hanging the sink. To Install: Remove the nut from the spout. From inside the cabinet, feed the spout through the hole in the top of the sink, and reinstall the nut. Attach the soap tubing.

8

9

10 `

11