INSTALLATION AND INSTRUCTION MANUAL
|
|
- Owen Short
- 6 years ago
- Views:
Transcription
1 BATH PRO TM 5.1 UNIT INSTALLATION AND INSTRUCTION MANUAL
2 INSTALLATION & INSTUCTION INDEX PAGE HydroSurge Bath Pro TM 5.1Unit Components...3 Before Starting...3 Installing the HydroSurge Bath Pro TM 5.1 Unit...4 First Time Operation Priming the System...6 Bathing Instructions...7 System Maintenance & Problem Solving...8 Important Information...9 Causes of Low Water Pressure...9 HYDROSURGE BATH PRO TM 5.1 SYSTEM - 2 -
3 HYDROSURGE BATH PRO TM 5.1 UNIT COMPONENTS Flow Control Valve Water-in Hose Mounting Bracket Mounting Bracket Wall Anchors (a) (b) (c) Screw 1¼ (d) Large (e) Bath Pro TM 5.1 Unit Male Hose Fitting Anti-Siphon Valve Wall Clamp Wall Clamp (f) (g) (h) (j) Screws 1 (k) Bathing Hose with Hose Clip Tubing Cap Adaptors Plastic Ties Nozzle (l) (m) (n) (p) (r) Tie Screws Wall Anchors End Cap ¾ (s) Small (t) (u) BEFORE STARTING 1. Please read and understand all instructions prior to beginning installation. If there are any questions, please call customer service at The HydroSurge Bath Pro TM 5.1 unit is designed to draw shampoo with as little as 4 gallons of water per minute; however, 5 or more gallons of water per minute is recommended. To test, hold a gallon sized container under the water source. If the container takes less than 12 seconds to fill, the water flow/pressure is adequate. Please review CAUSES FOR LOW WATER PRESSURE on page 9 if the water pressure is inadequate
4 INSTALLING A HYDROSURGE BATHPRO TM 5.1 UNIT 1. Determine a mounting location for the HydroSurge Bath Pro TM 5.1 unit within 5 feet of the water supply. If the preferred mounting location is greater than 5 feet from the water supply, a water-in hose extension will be necessary and is available for purchase by calling customer service at TIP: The Bath Pro 5.1 unit should be mounted at a convenient height and within easy reach to the left or right of the operator, whichever is closest to the water supply. There must be sufficient room below the Bath Pro 5.1 unit to allow for the bathing hose and tubing that connects to the product containers. TIP: Do not mount the BathPro 5.1 unit on the back wall of the tub where it may be subject to damage from biting or chewing animals. TIP: If an anti-siphon valve will be used, (step 9), consider that some water draining may occur. Consider mounting the unit over an area with drainage. 2. Attach the flow control valve (a) to the water source. The water source must have a male garden hose fitting; if it does not, a male garden hose fitting adaptor can be purchased inexpensively at a local hardware store. TIP: T&S Brass and Bronze Works, Inc. faucet fixtures have unique thread patterns and will only connect to garden hose adaptors that are sold by T&S Brass and Bronze Works, Inc. TIP: Use Teflon tape to help ensure a water tight fitting when connecting a pipe to a pipe fitting adaptor. TIP: Consider installing an elbow fitting between the water source and the flow control valve to keep the waterin hose close to the wall. 3. Attach the water-in hose (b) to the flow control valve (a). 4. While holding the mounting bracket (c) in the preferred mounting location, mark the screw holes. Secure the mounting bracket using the mounting bracket screws (d) ensuring that the tabs are pointing upwards. Plastic wall anchors - large (e) are provided if needed. TIP: When mounting on tile, use the grout line rather than drilling directly into the tile. TIP: Use the correct size and type drill bit for the mounting hardware and surface. Do not make the holes too large. TIP: Consider placing plumbers putty or bath tub sealant at the mounting holes, prior to installing the Bath Pro TM 5.1 unit to prevent water seepage through the mounting holes into the wall. 5. Align the slots on the back of the Bath Pro TM 5.1 unit (f) with the tabs on the mounting bracket (c) and lower to engage the tabs. 6. Route the open end of the water-in hose (b) to the top of the Bath Pro TM 5.1 unit (f). Cut off any excess hose, leaving enough slack to prevent the hose from crimping. 7. Remove the clamp from the male hose fitting (g) by removing the two screws. Soak the end of the hose in very warm water one minute to soften and insert the male hose fitting into the open end of the water-in hose (b). 8. Replace the fitting clamp on the male hose fitting (g) and secure it with the two screws. Alternate tightening each screw slightly. The two halves of the male hose fitting will not be touching even when the hose is securely fastened. Be careful not to over tighten the screws
5 9. Some local ordinances require the use of an anti-siphon valve. The anti-siphon valve (h) that is included in the installation packet is adequate for most, but not all, municipalities. Please consult with a plumber to determine local requirements. If required, attach the anti-siphon valve to the male hose fitting (g). Attach either the anti-siphon valve, if used, or the male hose fitting to the top of the Bath Pro TM 5.1 unit (f). 10. Use the supplied wall clamps (j) and wall clamp screws (k) to secure the water-in hose (b) to the wall. One of these clamps should be located near the Bath Pro TM unit. Plastic wall anchors - large (e) are provided if needed. 11. Connect the bathing hose with nozzle (l) to the bottom of the Bath Pro TM 5.1 unit (f). 12. Check all connections and tighten completely with pliers or a wrench as necessary. 13. Attach the hose clip (m) to either the left or right side of the Bath Pro TM 5.1 unit using one of the hose clip screws already inserted in the side of the unit. 14. Place the four gallon bottles of shampoo/conditioner in a convenient location that is close to and below the Bath Pro TM 5.1 unit (f). Connect the tubing (n) over the fitting labeled A located on the bottom of the Bath Pro TM 5.1 unit. Route the tubing to the top of one of the product bottles. Cut the tubing to length ensuring it is neither taught nor excessively loose. Repeat this step for the fittings labeled B, C, and D. TIP: For covenant cleaning and maintenance, leave enough tube length for the gallon bottle to reach the floor and the bottom of the tub. TIP: If you have any questions regarding the placement of bottles, or if you want to purchase additional tubing and/or a shampoo storage rack, please call customer service at Attach the four cap adaptors (p) to the end of the tubes. Remove the caps from the four gallon containers. Each gallon comes with an insert; the combination of the insert and the cap adaptor prevents contamination caused by foreign matter including hair and dirt as well as makes changing gallons quick and convenient. Screw the cap adapters completely onto the gallon containers by pushing down while turning the cap adaptor clockwise. When changing gallons containers, rinse the cap adaptor before replacing. 16. Only HydroSurge branded products can be used with the Bath Pro TM 5.1 unit. Use of other products is a violation of the Terms and Conditions of the free equipment usage program. Non-HydroSurge branded products can clog the system. Required repairs due to use of non- HydroSurge products are subject to a maintenance fee as outlined in the Terms and Conditions agreement up to and including the cost of the equipment. 17. Organize the tubing by using the plastic ties (r); anchor the ties to the wall using the tie screws (s) and wall anchors - small (t) if needed
6 FIRST TIME OPERATION - PRIMING THE SYSTEM 1. Select Rinse on the function selector. 2. Turn the water on and open the water flow valve. 3. Check for any leaks and tighten any connections as necessary. 4. Select product A on the product selection dial; this will correspond to the product attached to the tube labeled A at the bottom of the unit. 5. Select Bathe on the function selector. Open the product flow rate valve by turning the knob counter clock-wise completely until it stops. Never force this knob once it stops turning. Product should now be traveling through the product supply tube from the gallon container. 6. Once there are suds coming from the spray nozzle, close the product flow rate valve by turning the knob clockwise until it stops (approximately 6 rotations). 7. When there are only air bubbles and no suds coming from the spray nozzle, open the product flow rate valve by turning the knob counter-clockwise ¼ turn of one rotation and wait 10 seconds to allow the unit to adjust to the new setting. If there are still no suds coming out of the spray nozzle, open the product flow rate valve by turning the knob another ¼ turn of one rotation and wait another 10 seconds. If necessary, continue opening the valve in ¼ turn increments waiting 10 seconds to allow the unit to adjust. TIP: Most facilities require between ½ and 1½ rotations of the product flow rate knob. Needs will vary based on water flow, the length of tubing, the placement of the shampoo/conditioner containers, and the temperature of the products. While the product flow rate valve can be opened six complete rotations, for most facilities, this would draw far more product than is required to effectively clean an animal. TIP: The amount of shampoo needed should be just enough to break up the oils that hold the dirt in the hair. The vigorous action of the bathing solution physically removes the dirt from the animal. 8. Repeat the priming process for products B, C, and D
7 BATHING INSTRUCTIONS 1. Select Rinse on the function selector. Turn on your water and open the flow control valve so that water is flowing through the system. Adjust the water temperature to the desired setting. At any time during the bathing procedure the water flow can be turned off or reduced by using the flow control valve. TIP: Turn off the water at the water source when not in use for longer periods of time. The flow control valve is intended to provide a temporary shut off or reduction in water flow. 2. Select a product using the product selection dial. TIP: Use the most appropriate shampoo / conditioner for the animal being bathed. A complete line of HydroSurge shampoos and conditioners are available to address a wide array of coat and skin conditions. 3. Select Bathe on the function selector to infuse product into the water. 4. There is no need to pre-wet the animal. Hold the spray nozzle 3 to 4 inches from the animal s coat. The vigorous flow of oxygenated water / shampoo mixture will penetrate through the hair to the skin. Hand scrubbing is not necessary. Move the spray nozzle back and forth with a slow, steady motion, angling the spray pattern against the grain of the hair to ensure a thorough cleaning. TIP: Animals suffering from various skin conditions, arthritis, hip dysphasia, or other back, bone, or muscle problems can benefit from a warm holistic / therapeutic bath. Concentrate the spray in a circular motion on areas that are affected. TIP: Follow a slow methodical, top to bottom, and side to side pattern to ensure a thorough cleaning and relaxing massage for the animal. 5. Turn the animal after finishing one side and continue bathing the other side. TIP: Use a leash tie-down bar installed 12 inches above the tub rim to allow the animal to be turned easily. TIP: For extremely dirty and greasy animals, a quick bath using an ultra cleaning or degreasing formula shampoo is recommended. Without rinsing the animal first, follow this with a more thorough bath using an everyday use shampoo formula. 6. Switch from using one product to another by turning the product selection dial. It is not necessary to turn off the water first. TIP: Use the flow control valve to reduce water pressure when washing or rinsing an animal s face. For best results and safety, hand wash the animal s face with HydroSurge Aloe-Tearless shampoo. TIP: Flea and tick shampoos require that the animal be covered in lather for a specified amount of time to work. First bathe the animal using the Bath Pro TM 5.1 unit and a HydroSurge branded shampoo to thoroughly clean the animal and effectively wash away most parasites. Follow bottle instructions to hand apply the flea and tick shampoo. Use the Bath Pro TM 5.1 unit to efficiently rinse the animal. 7. After thoroughly bathing the animal, turn the function selector to Rinse. Within seconds, the combing action will consist of only oxygenated water. Repeat the methodical, slow, top to bottom, side to side action. Apply conditioner as needed. 8. When the Bath Pro TM 5.1 unit is not in use, the function selector should be left in the Rinse position. TIP: To quickly eliminate suds when draining bath water, use HydroSurge Suds-a-Way. Excessive suds may result from soft water or using more shampoo than necessary
8 SYSTEM MAINTENANCE & PROBLEM SOLVING Prevent Leaks: Tighten the fittings and replace the hose washer as necessary. Tighten Knob: If the product flow rate knob on your Bath Pro TM 5.1 unit becomes loose, tighten the set screw using a 1/16 Allen wrench. Bottles Collapse: If a product bottle collapses, make a pin hole in the bottle above the product level. Cold or Frozen Product: During cold weather, shampoos and conditioners can become more viscous or even freeze during transportation. In order to return product to room temperature, place the cold gallons in a dog kennel and hang a cage dryer set on high for approximately 30 minutes. If no cage dryer is available, set the gallon container in a sink and run warm water over the outside of the container. Always store products at room temperature. Lubricate the Valves: Every month or as necessary, place a few drops of household oil on the valve stems located behind the product selection dial and product flow rate valve knob. Clean the Spray Nozzle: Every month or as necessary, remove the spray nozzle from the bathing hose. Push the end of a paperclip through each hole and clean with a household lime and calcium cleaner. Rinse thoroughly ensuring that all debris is removed from around the nozzle holes. Clean the Screen Washer: Every three months or as necessary, use a toothbrush to clean the screen washer, located at the end of the water in-hose attached to the flow control valve. Back Flush the System: Product coagulation may cause blockage if either the system or any single product has not been used for an extended period of time. Dirt or hair may also occasionally cause blockage. If a blockage exists, there will be little or no suds coming out of the spray nozzle even when the product flow rate valve is fully open. Take the following steps to back-flush the system: 1. Remove the spray nozzle from the bathing hose and replace it with the end cap (u). 2. Detach the cap adaptors from the blocked product and place into the tub or a bucket. 3. Select the blocked product on the product selection dial. 4. Open the product flow rate valve by turning the knob counter clockwise until it stops. Never force this knob once it stops turning. 5. Select Bathe on the function selector and slowly turn on the water. TIP: For best results use very warm water. 6. Open and close the product flow rate valve by turning the knob clockwise and counterclockwise in order to help dislodge any debris in the valve. The blockage has been removed when there is a steady stream of water coming from the line. 7. If more than one product is blocked, repeat the process. If problems persist, please call customer service at
9 IMPORTANT INFORMATION 1. All Bath Pro 5.1 components are designed to work as part of a complete bathing system. They must be installed in the proper order, relative to each other, as outlined in these instructions. Placement of components in alternate configurations may result in system malfunction: water back up, excessive pressure, and flooding may result from improper installation. 2. Do not interchange any components of the Bath Pro 5.1 system including hoses and nozzles with any non-hydrosurge components. Use all components only as intended. 3. Do not operate the Bath Pro 5.1 unit if there are any leaks in the system. 4. Do not expose the Bath Pro 5.1 unit to temperatures below 40 degrees Fahrenheit. 5. The Bath Pro 5.1 unit contains no user serviceable parts. Repairs must be done by authorized service personnel only. Opening the Bath Pro 5.1 unit and attempting repairs or tampering with any component of the HydroSurge Bath Pro unit is a violation of the Terms and Conditions of the free equipment usage program. CAUSES OF LOW WATER PRESSURE If the water flow/pressure is too low to provide for adequate bathing/rinsing, there could be several causes: The main pressure regulator may be set too low; resolve by resetting the pressure regulator. The water supply mixing valve may have a built in flow restrictor; resolve by removing the restrictor. A flow restricted anti-siphon valve may be installed at the water supply; resolve by installing an anti-siphon valve that does not restrict flow. The water pressure may be low coming into the building; resolve by installing a pressure booster pump. Consult with a plumber as necessary. If you have any questions regarding this product please call or write to: Attn: Customer Service, Oster Professional Products, 150 Cadillac Lane, McMinnville, TN Made in USA of Domestic Parts 2004 Sunbeam Products, Inc. All rights reserved. Oster, HydroSurge, InjectAir, and Bath Pro are all registered trademarks of Sunbeam Products, Inc
DUOBATHE BATHING SYSTEM
DUOBATHE BATHING SYSTEM INSTALLATION AND INSTRUCTION MANUAL INSTALLATION AND INSTRUCTION INDEX PAGE DUOBATHE BATHING SYSTEM Components... 2 Important Information... 2 Before Starting... 3 Installing the
More informationPL-004-SS. * Proper water pressure is required for simultaneous operations
PL-004-SS Features - Stunning stylish European inspired design - Elegant durable stainless steel frame construction - 4 stage shower functions (Rainfall, Waterfall, Massage Spray, Hand Shower) - Simultaneous
More informationSuperKlean Washdown Products
February 2012 DURAMIX 8000 INSTALLATION AND MAINTENANCE INSTRUCTIONS **DO NOT THROW AWAY AFTER INSTALLATION** **SAVE AND DISPLAY PROMINENTLY WHERE THIS EQUIPMENT IS USED** WARNING HIGH PRESSURE AND HOT
More informationOWNER S MANUAL AND INSTALLATION GUIDE PLEASE READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING INSTALLATION
ClearChoice Economy Under Sink Drinking Water System OWNER S MANUAL AND INSTALLATION GUIDE PLEASE READ THIS MANUAL CAREFULLY BEFORE ATTEMPTING INSTALLATION Congratulations on the purchase of your ClearChoice
More informationINSTANT HOT WATER DISPENSER
INSTANT HOT WATER DISPENSER Tank Installation Materials required (not provided) 2 mounting bracket screws (and 2 plastic anchors if attaching to drywall) Shut-Off valve and T fitting Components When you
More informationClean Water Made Easy. CWS Time Clock Softener Installation & Start Up Guide. Questions?
Clean Water Made Easy www.cleanwaterstore.com CWS Time Clock Softener Installation & Start Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance
More informationBURWELL BIDET TOILET SEAT INSTALLATION
BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the product, plumbing, toilet,
More informationAcrylic Claw Foot Tub
Acrylic Claw Foot Tub Wrench or socket Drill & Bits Parts Recommended 2-2 x12 boards 4 Lag Bolts 4 Flat Washers Be sure to re-inforce the floor before securing tub. We recommend 2-2 x12 s securely fastened
More informationTap Master Artesian Hydro Gardener Series Installation & Service Manual
Perfect Water Technologies 7 Tips for an Easy and Successful Installation 1. Keep it simple - there are 3 connections to make, and the tubing is color coded. 2. Have plenty of time, light, space, and towels
More informationInstallation Instructions / Warranty
Installation Instructions / Warranty IP C 04210000 04211000 04212000 IP S 04203000 04204000 04205000 IP E 04199000 04200000 04201000 IP Trim Sets Valve trim only IP C 04212000 IP E 04201000 IP S 04205000
More informationINSTALLTION FOR THERMOSTATIC VALVES
SS-TH1000 ½ THERMOSTATIC VALVE SS-TH3000 ¾ THERMOSTATIC VALVE SS-TH2000 ½ THERMOSTATIC VALVE WITH BUILT IN VOLUME CONTROL SS-TH4000 ¾ THERMOSTATIC VALVE WITH BUILT IN VOLUME CONTROL Features: Ability to
More informationInstallation & Operating Guide
5-036 HOT WATER TANK Installation & Operating Guide Read all instructions thoroughly. Keep this guide for future reference. Proof of purchase is required for Warranty. Staple receipt or proof of purchase
More informationOahu Showerspa Model #1035 Owner's Manual
O A H U Oahu Showerspa Model #1035 Owner's Manual Oahu ShowerSpa Model #1034 Please Read The Following Instructions COMPLETELY Before Beginning! Our goal is to ensure your installation goes smoothly and
More informationInstallation and Operation Manual For Hunter Ceiling Fans
Installation and Operation Manual For Hunter Ceiling Fans 1 2 CONGRATULATIONS! Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years.
More informationDecor Star 1. Decor Star PL-037-SS
Decor Star PL-037-SS Features - Stunning stylish European inspired design - Durable stainless steel frame construction - Square stainless thin profile shower head - 3 swivel massage jets - 4 stage shower
More informationSS-THVD2-1/2 THERMOSTATIC VALVE WITH 2 WAY DIVERTER SS-THVD3-1/2 THERMOSTATIC VALVE WITH 3 WAY DIVERTER
SS-THVD2-1/2 THERMOSTATIC VALVE WITH 2 WAY DIVERTER SS-THVD3-1/2 THERMOSTATIC VALVE WITH 3 WAY DIVERTER Features: Ability to pre-select water temperature thus conserving water Paraffin wax element maintains
More informationOwner's Manual. WS Series. Water Softener
Owner's Manual WS-165-150 Series Water Softener Table of Contents WHAT'S INCLUDED 3 OPERATING CONDITIONS 4 ASSEMBLY INSTRUCTIONS 6 FLUSHING THE WATER LINES 13 MASTERPROGRAMMING 14 PROGRAMMING KEYAND GENERAL
More informationK Specifications. Max. Water Volume
K 2.35 High Pressure Washer Operator Manual Overview... 2 Precautions... 2-4 Assembly Instructions... 4 Operating Instructions... 5 Using the Accessories... 6 Working with Detergents... 7 Shut Down and
More informationTop Control Dishwasher
INSTALLATION GUIDE Top Control Dishwasher NS-DWH2BS8/NS-DWH2SS8/NS-DWR2BS8/NS-DWR2WH8/NS-DWR2SS8 Before using your new product, please read these instructions to prevent any damage. Contents Introduction......................................................................................................
More informationInstallation Instructions
Installation Instructions SELECTRONIC Hard-Wired AC Powered ICU Lavatory Proximity Faucet PRODUCT NUMBER 0. Certified to comply with ASME A..M 0 American Standard M 0. ICU Faucet shown Installed on American
More informationENCLOSED UNIT TECHNICAL MANUAL Items # &
R ENCLOSED UNIT TECHNICAL MANUAL Items #91163-00 & 91164-00 The Green Earth II Enclosed Unit is a modular, locking dispensing system that allows the user to dispense chemicals safely. It also has the flexibility
More informationInstallation Instructions. For the 18 Built-In Dishwasher and Front Color Panels
Installation Instructions For the 18 Built-In Dishwasher and Front Color Panels Printed in USA 154232102 Before You Begin DO NOT INSTALL DISHWASHER UNTIL YOU HAVE READ ALL INSTRUCTIONS. FOR YOUR SAFETY,
More informationInstructions. Certifications Chrome 2-handle Chrome 3-handle 10-B83-WCH-AD Chrome 3-handle 10-B82-WCH-AD Chrome 2-handle
Instructions 623282 Chrome 2-handle *Image may vary slightly from actual product Tools Required Adjustable Wrench Groove Joint Pliers Pipe Wrench Phillips Screwdriver Pipe Tape or pipe thread compound
More informationK Specifications. Max. Water Volume
K 2.75 High Pressure Washer Operator Manual Overview... 2 Precautions... 2-4 Assembly Instructions... 4 Operating Instructions... 5 Using the Accessories... 6 Working with Detergents... 7 Shut Down and
More informationAcrylic Claw Foot Tub
Acrylic Claw Foot Tub Wrench or socket Drill & Bits Parts Recommended 2-2 x12 boards 4 Lag Bolts 4 Flat Washers Be sure to re-inforce the floor before securing tub. We recommend 2-2 x12 s securely fastened
More informationINSTALLATION FOR THERMOSTATIC VALVES
SS-TH1000 1/2 Thermostatic Valve SS-TH3000 3/4 Thermostatic Valve SS-TH2000 1/2 Thermostatic Valve with built in volume control SS-TH4000 3/4 Thermostatic Valve with built in volume control Features: Ability
More informationAquaLiv Water System - Usage & Installation Instructions
AquaLiv Water System - Usage & Installation Instructions Congratulations on your purchase of an AquaLiv Water System the most complete and comprehensive water purification and enhancement system available
More informationModels: GW/R-T GW/R-2-T GW/R-3-T
Part# GW/R-T-OM 1/12/04 TN Models: GW/R-T GW/R-2-T GW/R-3-T This manual contains important information concerning the installation and operation of the gun washers listed above. Read manual thoroughly
More informationaquaphyll TM QUAD Wall Mounted Chemical Dispensing System
aquaphyll TM QUAD Wall Mounted Chemical Dispensing System w w w. p i o n e e r e c l i p s e. c o m aquaphyll tm QUAD wall mounted chemical dispensing system AquapHyll is the professional s choice in wall
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 5000 700069 50055 MODEL: Dillon 5000 (RH-600) 50055 (RH-600X) 700069 (TRRH-600) REV D Restoration Hardware Faucet Product Size Specification Diagram Recommended Deck Hole Size
More informationMINIATURE THERMOSTATIC VALVE
SS-TH500-1/2 Features: Ability to pre-select water temperature thus conserving water Compensates for water pressure fluctuations preventing scalding Safety button at 100 F prevents accidental scalding
More informationPulldown Kitchen Faucet
P25200 1 of 7 Thank You For Choosing Kallista We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before you install your Kallista product. If you encounter
More information7800 Neutralizer Installation & Start-Up Guide
Clean Water Made Easy www.cleanwaterstore.com 7800 Neutralizer Installation & Start-Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance your
More informationK 3.97 M. Specifications or visit our website: In USA call: Part No
K 3.97 M High Pressure Washer Operator Manual Overview... 2 Precautions... 2-4 Assembly Instructions... 4-5 Operating Instructions... 5-6 GFCI Instructions... 6 Using the Accessories... 6 Working with
More information173 Index of Materials
73 Index of Materials IBC Tank 9 Polystyrene Sheet 2 200 Litter Blue Barrels 0 Plumbers Tape (Teflon) 3 Fish Tank Shading Cable Ties 4 Plastic Net 2 Waterproof Eclectic Box 5 Concrete Blocks 3 0 mm Wide
More informationFerronTM. Instruction Manual A Kichler Decor ceiling fan
Includes our new CoolTouch TM 6 Speed DC Control System Looks permanent, but goes wherever you go! U.S. Patent Pending 300160 A Kichler Decor ceiling fan HIGH EFFICIENCY DC MOTOR FerronTM Kichler Lighting
More informationInstallation and Operation Manual For Hunter Ceiling Fans /16/2004
Installation and Operation Manual For Hunter Ceiling Fans 1 2 CONGRATULATIONS! Your new Hunter ceiling fan is an addition to your home or office that will provide comfort and performance for many years.
More informationInstallation & Operating Guide
HOT WATER DISPENSER Installation & Operating Guide Read all instructions thoroughly. Keep this guide for future reference. Proof of purchase is required for Warranty. Staple receipt or proof of purchase
More informationModel K 3000 G Part No
K3000G Manual 11/30/01 4:56 PM Page 1 Model K 3000 G Part No. 1.133-110.0 High Pressure Washer Operator Manual Overview..................................1 Precautions...............................1-2
More informationkk21 installation Kk21-WF21 Things you might need for the installation: vessel sink,
Kk21-WF21 Things you might need for the installation: vessel sink, plumber's putty(home depot), liquid nails(home depot), Bucket silicone caulk(home depot), Putty knife Plumber's putty Pipe wrench Channel-lock
More informationFeatures Luxier SP21-SS
Luxier SP21-SS Features - Stunning stylish European inspired design - Durable stainless steel frame construction - Square stainless thin profile shower head - 3 swivel massage jets - 3 stage shower functions
More informationen-us Use and Care Manual, Installation Instructions Washer WAT28400UC
en-us Use and Care Manual, Installation Instructions Washer WAT28400UC Under counter (Less Desirable) If front of the appliance is covered ventilation openings must be installed. E & F are minimum area
More informationPet. Easy Guide. VAX Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK - website:
V-027P Rapide Pet User Guide 10/7/07 10:05 Page 14 EEC STATEMENT OF COMPLIANCE Manufacturer/EEC importer: VAX Limited, hereby on our own responsibility declare that the products V-027/V-027PT/V-027P/CCW-701
More informationFeatures Luxier SP21-SS
Luxier SP21-SS Features - Stunning stylish European inspired design - Durable stainless steel frame construction - Square stainless thin profile shower head - 3 swivel massage jets - 3 stage shower functions
More informationPage 1 of 18. Part# /5/2013
Part# 1002655-06 8/5/2013 This manual contains important information concerning the installation and operation of the gun washers listed above. Read manual thoroughly and keep for future reference INSTRUCTIONS
More informationONE PIECE TOILET LT3. Model: MPN: B0940 INSTALLATION INSTRUCTIONS. Version: 1.0
Model: MPN: B0940 INSTALLATION INSTRUCTIONS Version: 1.0 READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING
More informationTUB AND SHOWER FAUCET
AquaSource is a registered trademark of LF, LLC. All Rights Reserved. ITEM #004057 0040555 TUB AN SHOWER FAUCET MOEL #873-370 873-377H Francias / Español p. 3 ATTACH YOUR RECEIPT HERE Serial Number Purchase
More informationWARRANTY POLICY & RECOMMENDED MAINTENANCE
WARRANTY POLICY & RECOMMENDED MAINTENANCE WARRANTY POLICY The following information will explain the plumbing components and warranty coverage for the plumbing systems and fixtures in your new home. It
More informationOwner s Guide and Installation Manual
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Model Name Type 2 Models Owner s Guide and Installation Manual Model No. Date Purchased
More informationOwner s Guide and Installation Manual
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Model Name Type 8 Models Owner s Guide and Installation Manual Model No. Catalog
More informationInstallation Manual PS-200 & PS-201
Installation Manual PS-200 & PS-201 Table of Contents Pre-Uncrating Checklist... 1 Verifying System Requirements... 2 Verifying System Direction... 2 Verifying the Electrical Requirements... 2 Removal
More informationClean Water Made Easy. Fleck 7000 Tannin Filter Installation & Startup Guide. Questions?
Clean Water Made Easy www.cleanwaterstore.com Fleck 7000 Tannin Filter Installation & Startup Guide For Tannin Filters with Vortech Distributor Screen Thank you for purchasing a Clean Water System! With
More informationDS 2001 REVISED Humidifier Assembly and Instruction Manual
DS 2001 REVISED Humidifier Assembly and Instruction Manual Contents Parts list Selecting a location Assembly Hanging the Basin Electrical connections Water connections 2 4 4 Installing the Disk Wheel Installing
More informationKITCHEN FAUCET COS-KF222C
KITCHEN FAUCET COS-KF222C USER S MANUAL & INSTALLATION GUIDE Thank You Thank you for your purchase. We know that you have many brands and products to choose from and we are honored to know that you have
More informationInstallation Instructions
Installation Instructions SELECTRONIC Thermostatic Mixing Valve 605XTMV Certified to comply with ASME A.8.M 005 American Standard M968808 Specifications Installation Adjust Temperature Service Replacement
More informationPIPE DREAMS 96. Aeroponic Garden IMPORTANT:
1 WARNING: BEFORE PUTTING WATER PUMP INTO OPERATION FILL UP NUTRIENT TANK TO TOP OF PUMP. THE PUMP MUST NEVER RUN DRY OTHERWISE, WARRANTY WILL BE DECLINED. READ FILLING INSTRUCTIONS BEFORE USE. Welcome
More informationModel K 520 M Part No
Model K 520 M Part No. 1.069-680.0 High Pressure Washer Operator Manual Overview... 2 Precautions... 2-4 Assembly Instructions... 4 Operating Instructions... 5 Using the Accessories... 6 Working with Detergents...
More informationIMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric appliances, basic
INSTRUCTIONS PERTAINING TO; RISK OF FIRE, ELECTRIC SHOCK OR HARM TO PERSONS IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric appliances, basic precautions should always be followed, including
More informationInstallation Instructions
Instructions for Frontload Washers Original Instructions Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) www.alliancelaundry.com Part
More informationPORTABLE DOG BATH TOOL
TM PORTABLE DOG BATH TOOL USER GUIDE 1842 SERIES More of a video person? Look for this icon and go online for an instructional how-to video at BISSELL.com/videos IMPORTANT SAFETY INSTRUCTIONS READ ALL
More informationInstallation Manual PS-225 & PS-275
Installation Manual PS-225 & PS-275 Table of Contents Pre-Uncrating Checklist... 1 Verifying System Requirements... 2 Verifying System Direction... 2 Verifying the Electrical Requirements... 2 Removal
More informationPolyMax H2-24 Dutch Bucket System
11234 PolyMax H2-24 Dutch Bucket System *Actual system may differ. PolyMax Dutch Buckets Versatile PolyMax Dutch Buckets are ideal for both small- and large-scale hydroponic growing. 2017 FarmTek All Rights
More informationThe Marine Throne. Model TMT S/37045/X-Series QUIET - FLUSH ELECTRIC TOILET. "all the comforts of home" FEATURES SPECIFICATIONS INSTALLATION
The Marine Throne "all the comforts of home" Model TMT S/37045/X-Series QUIET - FLUSH ELECTRIC TOILET FEATURES Very quiet flush cycle - like a household toilet Single button flush actuator - with dual
More informationFeatures Decor Star PL-004-SS
Decor Star PL-004-SS Features - Stunning stylish European inspired design - Elegant durable stainless steel frame construction - 4 stage shower functions (Rainfall, Waterfall, Massage Spray, Hand Shower)
More informationModel Series. PumpAgents.com - buy pumps and parts online QUIET - FLUSH ELECTRIC TOILET. Model Series FEATURES SPECIFICATIONS INSTALLATION
PumpAgents.com - Click here for Pricing/Ordering Model 37045-Series QUIET - FLUSH ELECTRIC TOILET FEATURES Very quiet flush cycle - like a household toilet Single button flush actuator - with dual function
More informationTIMES SQUARE TWO-HANDLE THERMOSTAT
TIMES SQUARE TWO-HANDLE THERMOSTAT MODEL NUMBER: TRIM KITS: T184.740 Two-Handle Thermostat Trim Kit With separate volume control. LESS Valve. ROUGH VALVES: TEMPERATURE & ON/OFF VOLUME CONTROL ONLY R50
More informationInstructions CH Chrome SS Stainless Steel Certifications. Single Handle, Pull-Down, Kitchen Faucet. Tools Required.
Instructions *Image may vary slightly from actual product Tools Required Adjustable Wrench Groove Joint Pliers Pipe Wrench Phillips Screwdriver Pipe Tape or pipe thread compound Safety Tips If you solder
More informationK 2.97 M. Specifications Operating pressure, max PSI Water volume GPM Voltage V Amp draw AMPS
K 2.97 M High Pressure Washer Operator Manual Overview... 2 Important Precautions... 3-4 Assembly Instructions... 4 Operating Instructions... 5 GFCI Instructions... 6 Using the Accessories... 6 Working
More informationSCHWAN INSTALLATION GUIDE
1 SCHWAN INSTALLATION GUIDE For Schwan SC60 FOR SERVICE OR ASSISTANCE CALL MERQUIP ON 0800 636 0 636. Schwan recommends that a qualified tradesperson installs your Schwan system. 2 INFORMATION AND SAFETY
More informationWAILEA OWNER S MANUAL
WAILEA OWNER S MANUAL The blades in each pack are matched for equal weight to assure smooth fan operation. If more than one fan is being installed, be careful not to mix blades from different cartons.
More information1. SAFETY RULES WARNING WARNING. 8. Avoid placing objects in the path of the blades.
1 1. SAFETY RULES 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the National
More informationModel HD 3501 Part No High Pressure Washer Operator Manual
0 15 25 40 25 Nozzle Identification SOAP HD3501 Manual 4/22/02 6:57 PM Page 1 Model HD 3501 Part No. 1.810-999.0 High Pressure Washer Operator Manual Overview..................................1 Precautions...............................1-2
More informationINSTALLATION GUIDE HIGH PRESSURE CLEANER (1800C) If there is any question during using, please feel free to contact us by
INSTALLATION GUIDE HIGH PRESSURE CLEANER (1800C) Contact us If there is any question during using, please feel free to contact us by email: service@paxcess.com sale05@gadgetwoo.com After unpacking the
More informationUnpacking and removing shipping bolts. Connecting the drain line Leveling the washer Connecting to the power supply
11 INSTALLATION Installation Overview Choosing the proper location Unpacking and removing shipping bolts Connecting the water line Connecting the drain line Leveling the washer Connecting to the power
More informationEnglish. Your Model Number is: HD1500 IMPORTANT
Your Model Number is: HD1500 IMPORTANT Attention Valued Customer: The serial number of your machine and date of purchase is necessary information to facilitate warranty claims and the ordering of replacement
More informationAlkaline RO System INSTALLATION MANUAL
Alkaline RO System INSTALLATION MANUAL 1-800-992-8876 Customer Support Disclaimer All rights reserved. All material published on this site by Express Water Inc., including all portions of the website,
More informationFLECK 5600 WATER SOFTENER INSTALLATION
FLECK 5600 WATER SOFTENER INSTALLATION Discount Water Softeners recommends using a licensed plumber to install your water softener. The following installation instructions are for use with the water softener
More informationValkyrieTM. Instruction Manual. Includes our new CoolTouch TM 6 Speed DC Control System Looks permanent, but goes wherever you go! U.S.
ValkyrieTM A Kichler Décor ceiling fan Designed to coordinate with a popular Kichler Lighting collection. Includes our new CoolTouch TM 6 Speed DC Control System Looks permanent, but goes wherever you
More informationParts & Material Included
O² Hydro Well System Installation, Use & Care Guide Parts & Material Included 1. Funnel 11. Drain Line 21. Air Head 2. Media Tank Distributer Tube 12. Air Release 22. Drain Fitting 3. Air Tank Distributer
More information42 Kevlar. Instruction Manual. Kichler Lighting 7711 East Pleasant Valley Road P.O. Box Cleveland, Ohio
42 Kevlar Kichler Lighting 7711 East Pleasant Valley Road P.O. Box 318010 Cleveland, Ohio 44131-8010 Customer Service 866.558.5706 8:30 AM to 5:00 PM EST, Monday - Friday Instruction Manual 1 1. SAFETY
More informationPrimePour TM Operation Manual
COT2000 SERIES PrimePour TM Operation Manual READ BEFORE USE. 840247001 7/14 For more Good Thinking visit www.commercial.hamiltonbeach.com 840247001_v18.indd 1 IMPORTANT SAFETY INSTRUCTIONS WARNING When
More informationOwner s Guide and Installation Manual
Tribeca Owner s Guide and Installation Manual English Form# M6001-01 20120416 2012 Casablanca Fan Co. Welcome Your new Casablanca ceiling fan is an addition to your home or office that will provide comfort
More informationInstallation Instructions
Installation Instructions For the 18" Built-In Dishwasher Sears, Roebuck and Co. Sears Canada, Inc. Hoffman Estates, IL 60179 U.S.A. Toronto, Ontario, Canada M5B 2B8 154435201 Before You Begin DO NOT INSTALL
More informationDishwasher Installation Instructions DW 24XT/DW 24XV
Dishwasher Installation Instructions DW 24XT/DW 24XV Installation Instructions Dishwasher BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT Observe all governing codes and ordinances.
More informationInstallation Instructions
Installation Instructions SELECTRONIC Thermostatic Mixing Valve 0XTMV070 Certified to comply with ASME A.8.M 0 American Standard M97 Specifications Installation Adjust Temperature Service Replacement Parts
More informationREVE ORDERING INFORMATION NOTES T01-A INSTALLATION INSTRUCTIONS 现代型分体座便器 CONTEMPORARY TWO-PIECE TOILET K-17178T-S/K-17178T-SP
REVE INSTALLATION INSTRUCTIONS 现代型分体座便器 CONTEMPORARY TWO-PIECE TOILET K-17178T-S/K-17178T-SP Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation
More informationINSTALLATION INSTRUCTIONS
Model: MPN: AN5534 INSTALLATION INSTRUCTIONS Version: 1.0 READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING
More informationHandshower, Hose & Handshower Accessories
P24443, P24445, P24446, P24452, P24453, P24456 1 of 6 INSTALLATION INSTRUCTIONS Thank You For Choosing KALLISTA We appreciate your commitment to KALLISTA quality products. Please take a moment to review
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 3580079 3580006 MODEL: LUGARNO 3580006 (RH-5900) 3580079 (RH-5900L) REV C Restoration Hardware Faucet Product Size Specification Diagram Recommended Deck Hole Size -3/8 Diameter
More informationKIT NOTICE. These instructions are for replacing the three existing thermostats with a single new solid-state thermostat.
KIT 06401-004-22-16 5 1 2 NOTICE 3 (3 PLC'S) These instructions are for replacing the three existing thermostats with a single new solid-state thermostat. 4 PREPARATION PARTS INCLUDED 6 1 7 5 8 2 4 (4
More informationInstructions. Certifications CH Chrome SS Stainless Steel. Single Handle, Industrial Style, Pull-Down Kitchen Faucet.
Instructions *Image may vary slightly from actual product Tools Required Adjustable Wrench Groove Joint Pliers Pipe Wrench Phillips Screwdriver Pipe Tape or pipe thread compound Safety Tips If you solder
More informationAVENGER HT THERMOSTAT RETROFIT INSTRUCTIONS
AVENGER HT THERMOSTAT RETROFIT INSTRUCTIONS In this installation manual: You will remove the existing mechanical thermostat from the Avenger HT dishwasher and will replace it with a new solid state thermostat.
More informationModel K 330 M Part No
Model K 330 M Part No. 1.994-916.0 High Pressure Washer Operator Manual Overview..................................1 Precautions...............................1-3 Assembly Instructions.........................3
More informationLaceyTM. Instruction Manual. Includes our new CoolTouch TM 6 Speed DC Control System Looks permanent, but goes wherever you go! U.S.
LaceyTM A Kichler Décor ceiling fan Designed to coordinate with a popular Kichler Lighting collection. Includes our new CoolTouch TM 6 Speed DC Control System Looks permanent, but goes wherever you go!
More informationClean Water Made Easy
Clean Water Made Easy http://www.cleanwaterstore.com Pro-OX 1650 Iron Filter Installation & Start-Up Guide Thank you for purchasing a Clean Water System! With proper installation and a little routine maintenance
More informationBACK WASH INSIDE THE SPA
BACK WASH INSIDE THE SPA Lower the temperature to 90 degrees and let the unit run approximately 10-15 minutes. This gives the heating element the chance to cool down. Now unplug the power pack Using a
More informationSetup. Important. Texture Spraying (material supplied from unit)
Setup Setup Important If you are going to stop spraying for more than 5 minutes, turn sprayer off to prevent shortened pump hose life. Do not allow material to dry inside pump, hoses, gun or spray system.
More informationInstructions. 110-KVD-CYSCH-AD-Z Chrome 110-KVD-CYSSS-AD-Z Stainless Steel Certifications. Single Handle, Pull-Down, Kitchen Faucet
Instructions *Image may vary slightly from actual product Tools Required Adjustable Wrench Groove Joint Pliers Pipe Wrench Phillips Screwdriver Pipe Tape or pipe thread compound Safety Tips If you solder
More informationIB 835. Installation Manual. Integrated Bidet Toilet TABLE OF CONTENTS
IB 835 Installation Manual Integrated Bidet Toilet Cautions before installation Water supply should have a minimum water pressure of 10 psi For smooth drainage, water pressure must stay at its required
More informationWall Mount Electric Fireplace
Wall Mount Electric Fireplace User Guide Thank you for purchasing the Ivation Wall Mount Electric Fireplace. This User Guide is intended to provide you with guidelines to ensure that operation of this
More information