ORDER CODES T-642B 76T82- D10 77T-662C. CODE DESCRIPTION 38 3/16 6HN 1/2" x 1/2" NPT steel hex nipple 1" "E" length 48 1/4 68 3/8

Transcription

1 Explosion-Proof, Fixed-Element RTDs are made for use in U.S. and Canadian hazardous areas. They are designed to extinguish flames inside the device, eliminating the potential for ignition of flammable mixtures in the surrounding atmosphere. FM and CS approved assemblies, dependent on connection head type, meet Class I Division I & II; Groups, B, C, D; DIP Class II Division I; Groups E, F, G; Class III; Type 4/4X. They may be installed directly in the process without being inserted into a thermowell. The assemblies feature 316 stainless steel sheaths in various diameter sizes. They are available with or without process mountings and with aluminum or stainless steel explosion-proof connection heads. X Configuration Code 01 Hazardous Location Explosion-Proof-pproved, Fixed-Element RTD ssemblies CS file # ORDER S Order Number: R1T185L HN 94, T- 5-2 gency pproval Ω Platinum RTD Elements α = ºC -1 TOLERNCE [1] LOW RNGE WIRE WOUND (-200 to 200) ºC SINGLE DUPLEX R1T185L R1T285L Grade B R5T185L R5T285L (1/5) Class B LOW RNGE THIN FILM (-50 to 200) ºC RBF185L RBF285L Class B RF185L RF285L Class HIGH RNGE WIRE WOUND (-200 to 600) ºC R1T185H RT185H FM/CS explosion-proof-approved R1T285H Grade B RT285H Class 74 DIN form B aluminum explosion-proof head, Group 76T82- D10 (4 to 20) m HRT Field Transmitter with aluminum explosion-proof housing, Group (4 to 20) m dual input HRT Field Transmitter with digital display and explosion-proof housing, Group (4 to 20) m HRT Field Transmitter with dual cavity explosion-proof aluminum housing, Group 93 luminum explosion-proof head, Group L stainless steel explosion-proof head, Group SB 1/2" NPT conduit reducer bushing I Stainless steel tag T-440 [1] (4 to 20) m head-mounted T-441 (4 to 20) m isolated head-mounted [1] Refer to RTD tolerance information in the General T-442 (4 to 20) m HRT isolated head-mounted Information section for calculations to determine specific tolerance at temperature. (4 to 20) m dual input, isolated HRT T82-00 head-mounted See ordering information in back of section. 2-1 Sheath Diameters 316 SS [1] Not available with option 74 WS DIMETERS HED NOW (inches) 94C HED BL 8/8/ Head Mounting This Fittings document is PROPRIETRY to 28 [1] 1/8 BY DTE Pyromation, Inc. 38 3/16 6HN 1/2" x 1/2" NPT steel hex nipple 1" "E" length 48 1/4 68 3/8 8HN 1/2" x 1/2" NPT stainless steel hex nipple 1" "E" length [1] Not available in duplex 9HP 1/2" NPT stainless steel bushing (no process threads) 8RNDC 3/4" x 1/2" NPT stainless steel hex nipple 2-2 Element Connection 4-0 Sheath Mounting Fittings 2 2-wire element 00 No Fitting 3 3-wire element 3-0 "X" Dimensions 4 [1] 4-wire element Insert three digit sheath length [1] Not available in duplex or with 440 Series Transmitter ("X" Dimension) in inches. HRT is a registered trademark of the HRT Communication Foundation Phone (260) FX (260) or (800)

2 Configuration Code 02 Hazardous Location Explosion-Proof-pproved, Fixed-Element Thermocouple ssemblies Explosion-Proof, Fixed-Element Thermocouples are made for use in U.S. and Canadian hazardous areas. They are designed to extinguish flames inside the device, eliminating the potential for ignition of flammable mixtures in the surrounding atmosphere. FM and CS approved assemblies, dependant on connection head type, meet Class I Division I & II; Groups, B, C, D; DIP Class II Division I; Groups E, F, G; Class III; Type 4/4X. They may be installed directly in the process without being inserted into a thermowell. The assemblies feature 316 stainless steel sheaths in various diameter sizes and ungrounded isolated junctions. They are available with or without process mountings and with aluminum or stainless steel explosion-proof connection heads. X CS file # ORDER S Order Number: - K 4 8 U HN 93, T- gency pproval 2-0 Thermocouple Types SINGLE DUPLEX TRIPLEX E EE - J JJ JJJ K KK KKK T TT - 74 DIN form B aluminum explosion-proof head, Group B 76T82- D10 (4 to 20) m HRT Field Transmitter with aluminum explosion-proof housing, Group (4 to 20) m dual input HRT Field Transmitter with digital display and explosion-proof housing, Group (4 to 20) m HRT Field Transmitter with dual cavity explosion-proof aluminum housing, Group 93 luminum explosion-proof head, Group L stainless steel explosion-proof head, Group SB I 1/2" NPT conduit reducer bushing Stainless steel tag 2-1 Sheath Diameters T-441 (4 to 20) m isolated head-mounted DIMETER (inches) (4 to 20) m HRT isolated head-mounted T /8 (4 to 20) m dual input, isolated HRT T82-00 head-mounted B2 3 3/16 4 1/4 See ordering information in back of section. 6 3/8 5-0 Head Mounting Fittings WS HED NOW 94C HED BL 8/8/ Sheath Materials This document is PROPRIETRY to BY DTE Pyromation, Inc. MTERIL STNDRD VILBLE TYPES 6HN 1/2" x 1/2" NPT steel hex nipple 3 lloy 600 K 8HN 1/2" x 1/2" NPT stainless steel hex nipple SS K 9HP 1/2" NPT stainless steel bushing (no process threads) SS K 8RNDC 3/4" x 1/2" NPT stainless steel hex nipple 2-3 Measuring Junction FM/CS explosion-proofapproved SS E, J, K, T 4-0 Sheath Mounting Fittings 00 No Fitting U Ungrounded 3-0 "X" Dimensions HRT is a registered trademark of the HRT Communication Foundation. Insert three digit sheath length ("X" Dimension) in inches. -2 Phone (260) FX (260) or (800)

3 Configuration Code 03 Hazardous Location Explosion-Proof-pproved, RTD ssemblies with Thermowells Explosion-Proof RTD ssemblies with Thermowells are made for use in U.S. and Canadian hazardous areas. They are designed to extinguish flames inside the device, eliminating the potential for ignition of flammable mixtures in the surrounding atmosphere. FM and CS approved assemblies, dependant on connection head type, meet Class I Division I & II; Groups, B, C, D; DIP Class II Division I; Groups E, F, G; Class III; Type 4/4X. The required thermowell is available in standard, heavy-duty, and flanged constructions. The assemblies feature 316 stainless steel sheaths. They are available with aluminum or stainless steel explosion-proof connection heads. 1/4" S E CS file # U ORDER S Order Number: Select Thermowell Part # - SC - from Thermowell Section R1T185L HN, 5-2 I gency pproval Ω Platinum RTD Elements α = ºC -1 TOLERNCE [1] LOW RNGE WIRE WOUND (-200 to 200) ºC SINGLE DUPLEX R1T185L R1T285L Grade B R5T185L R5T285L (1/5) Class B LOW RNGE THIN FILM (-50 to 200) ºC RBF185L RBF285L Class B RF185L RF285L Class HIGH RNGE WIRE WOUND (-200 to 600) ºC R1T185H R1T285H Grade B RT185H RT285H Class [1] Refer to RTD tolerance information in the General Information section for calculations to determine specific tolerance at temperature. 2-1 Sheath Diameters 316 SS 48 1/4 2-2 Element Connection 2 2-wire 3 3-wire 4 [1] 4-wire FM/CS explosion-proof-approved DIMETERS (inches) [1] Not available in duplex or with 440 Series Transmitter HRT is a registered trademark of the HRT Communication Foundation. 3-0 Thermowell Select thermowell part number from Thermowell Section. 5-0 Head Mounting Fittings STEEL FITTINGS 6HN 6PN_ 6XU_ 1] 4-0 Element Options SL [1] SC 74 DIN form B aluminum explosion-proof head, Group 76T82-D10 (4 to 20) m HRT Field Transmitter with aluminum explosionproof housing, Group (4 to 20) m dual input HRT Field Transmitter with digital display and explosion-proof housing, Group (4 to 20) m HRT Field Transmitter with dual cavity explosionproof aluminum housing, Group 93 luminum explosion-proof head, Group L stainless steel explosion-proof head, Group SB I 1/2" NPT conduit reducer bushing Stainless steel tag T-440 [1] (4 to 20) m head-mounted T-441 (4 to 20) m isolated head-mounted T-442 (4 to 20) m HRT isolated head-mounted T82-00 (4 to 20) m dual input, isolated HRT head-mounted See ordering information in back of section. [1] Not available with option 74. 1/2" x 1/2" NPT hex nipple 1" length 1/2" NPT pipe nipple 1/2" NPT union/nipple [1] 3 1/2" Minimum length required. Maximum allowable "E" length is 9" Spring-loaded element Self-contained, spring-loaded element [1] Not available with option 316SS FITTINGS 8HN 8PN 8XU_ [1] 1/2" x 1/2" NPT hex nipple 1" length 1/2" NPT pipe nipple 1/2" NPT union/nipple Phone (260) FX (260) or (800)

4 Configuration Code 04 Hazardous Location Explosion-Proof-pproved, Thermocouple ssemblies with Thermowells Explosion-Proof Thermocouple ssemblies with Thermowells are made for use in U.S. and Canadian hazardous areas. They are designed to extinguish flames inside the device, eliminating the potential for ignition of flammable mixtures in the surrounding atmosphere. FM and CS approved assemblies, dependant on connection head type, meet Class I Division I & II; Groups, B, C, D; DIP Class II Division I; Groups E, F, G; Class III; Type 4/4X. The required thermowell is available in standard, heavy-duty, and flanged constructions. The assemblies feature 316 stainless steel sheaths and ungrounded isolated junctions. They are available with aluminum or stainless steel explosion-proof connection heads. 1/4" S E CS file # U ORDER S Order Number: J 48 U - - SL - 8XU4 94, I Select Thermowell Part # from Thermowell Section gency pproval 2-1 Thermocouple Types SINGLE DUPLEX TRIPLEX E EE - J JJ JJJ K KK KKK T TT Sheath Diameters 316 SS (4 to 20) m HRT Field Transmitter with aluminum explosion-proof housing, Group DIMETER (inches) (4 to 20) m dual input HRT 48 1/4 76T82-D10 Field Transmitter with digital display and explosion-proof housing, Group WS HED NOW 94C HED BL 8/7/2013 This document is PROPRIETRY to (4 to 20) m HRT BY DTE Field Transmitter Pyromation, with Inc. dual cavity explosion-proof 2-3 Measuring Junction aluminum housing, Group 93 luminum explosion-proof head, Group U Ungrounded L stainless steel explosion-proof head, Group 3-0 Thermowell Select thermowell from Thermowell Section. 4-0 Element Options SL [1] SC FM/CS explosion-proofapproved Spring-loaded element Self-contained springloaded element [1] Not available with option 5-0 Head Mounting Fittings STEEL FITTINGS 74 DIN form B aluminum explosion-proof head, Group SB I 1/2" NPT conduit reducer bushing Stainless steel tag 316SS FITTINGS 6HN 1/2" x 1/2" NPT hex nipple 1" length 8HN 1/2" x 1/2" NPT hex nipple 1" length 6PN_ 6XU_ [1] 1/2" NPT pipe nipple 1/2" NPT union/nipple [1] 3 1/2" minimum length required Maximum allowable "E" length is 9" HRT is a registered trademark of the HRT Communication Foundation. 8PN 8XU_ [1] T-441 (4 to 20) m isolated head-mounted T-442 (4 to 20) m HRT isolated head-mounted T82-00 (4 to 20) m dual input, isolated HRT head-mounted See ordering information in back of section. 1/2" NPT pipe nipple 1/2" NPT union/nipple B Phone (260) FX (260) or (800)

5 Configuration Code 05 Hazardous Location Explosion-Proof-pproved, Spring-Loaded RTD ssemblies Explosion-Proof, Spring-Loaded RTDs are made for use in U.S. and Canadian hazardous areas. They are designed to extinguish flames inside the device, eliminating the potential for ignition of flammable mixtures in the surrounding atmosphere. FM and CS approved assemblies, dependant on connection head type, meet Class I Division I & II; Groups B, C, D; DIP Class II Division I; Groups E, F, G; Class III; Type 4/4X. Pyromation provides sensors for installation into your existing thermowell or provides the required thermowell as part of the. Refer to the Thermowell Section of this catalog for product selection. The assemblies feature 316 stainless steel sheaths. They are available with aluminum or stainless steel explosion-proof connection heads. Note: The "S" dimension will measure 1/4" longer than specified when the spring is in the relaxed postition. The "S" dimension is calculated when the sensor is compressed or in the installed position. This design allows 1/4" spring compression to ensure positive contact with the bottom of the thermowell. S CS file # ORDER S Order Number: - R1T185L FP - 8HN 93, T- gency pproval Ω Platinum RTD Elements α = ºC -1 TOLERNCE [1] LOW RNGE WIRE WOUND (-200 to 200) ºC SINGLE DUPLEX R1T185L R1T285L Grade B 5-0 Head Mounting Fittings 316 STINLESS STEEL FITTINGS 8HN 8PU4 [1] 1/2" NPT flame-path fitting (1-1/2" "E" length) 1/2" NPT union/nipple with flame-path fitting (specify "E" length in inches, maximum allowable 9") [1] For longer lengths replace "4" with length in inches. 4-0 Element Options FP 74 DIN form B aluminum explosion-proof head, Group 75T-642D 76T82-D10 Spring-loaded element with flame path 3-0 "S" Dimensions (4 to 20) m HRT Field Transmitter PYROMTION with aluminum P/N: - explosion-proof housing, Group B (4 to 20) m dual input HRT Field Transmitter with digital display and explosion-proof housing, Group (4 to 20) m HRT Field Transmitter with dual cavity explosion-proof aluminum housing, Group 93 luminum explosion-proof head, Group L stainless steel explosion-proof head, Group R5T185L R5T285L (1/5) Class B LOW RNGE THIN FILM (-50 to 200) ºC SB 1/2" NPT conduit reducer bushing RBF185L RBF285L Class B I Stainless steel tag RF185L RF285L Class T-440 (4 to 20) m head-mounted WS HED NOW 93C HED BL 8/7/2013 This document is PROPRIETRY to HIGH RNGE WIRE WOUND (-200 to 600) ºC BY DTE T-441 (4 to 20) Pyromation, m isolated Inc. head-mounted R1T185H R1T285H Grade B T-442 (4 to 20) m HRT isolated head-mounted RT185H RT285H Class [1] Refer to RTD tolerance information in the General Information section for calculations to determine specific tolerance at temperature. 2-1 Sheath Diameters 316 SS 48 1/4 2-2 Element Connection 2 2-wire 3 3-wire 4 [1] 4-wire FM/CS explosion-proof-approved DIMETERS (inches) [1] Not available in duplex or with 440 Series Transmitter HRT is a registered trademark of the HRT Communication Foundation. T82-00 (4 to 20) m dual input, isolated HRT head-mounted See ordering information in back of section. Insert three digit sheath length ("S" Dimension) in inches B Phone (260) FX (260) or (800)

6 Configuration Code 06 Hazardous Location Explosion-Proof-pproved, Spring-Loaded Thermocouple ssemblies Explosion-Proof, Spring-Loaded Thermocouples are made for use in U.S. and Canadian hazardous areas. They are designed to extinguish flames inside the device, eliminating the potential for ignition of flammable mixtures in the surrounding atmosphere. FM and CS approved assemblies, dependant on connection head type, meet Class I Division I & II; Groups B, C, D; DIP Class II Division I; Groups E, F, G; Class III; Type 4/4X.Pyromation provides sensors for installation into your existing thermowell or provides the required thermowell as part of the. Refer to the Thermowell Section of this catalog for product selection. The assemblies feature 316 stainless steel sheaths and ungrounded isolated junctions. They are available with aluminum or stainless steel explosion-proof connection heads. Note: The "S" dimension will measure 1/4" longer than specified when the spring is in the relaxed postition. The "S" dimension is calculated when the sensor is compressed or in the installed position. This design allows 1/4" spring compression to ensure positive contact with the bottom of the thermowell. S CS file # Order Number: ORDER S J 48 U 012 FP 8HN 94, T- 5-2 gency pproval 74 DIN form B aluminum explosion-proof head, Group PYROMTION P/N: FP-8HN 75T-642D (4 to 20) m HRT Field Transmitter with aluminum explosion-proof housing, Group B (4 to 20) m dual input HRT 76T82-D10 Field Transmitter with digital display and explosion-proof housing, Group 2-1 Thermocouple Types (4 to 20) m HRT Field Transmitter with dual cavity explosion-proof aluminum housing, Group SINGLE DUPLEX TRIPLEX 93 luminum explosion-proof head, Group E EE L stainless steel explosion-proof head, Group B J JJ JJJ K KK KKK SB 1/2" NPT conduit reducer bushing T TT - I Stainless steel tag WS HED NOW 93C HED BL 8/7/2013 T-441 This (4 document to 20) m is isolated PROPRIETRY head-mounted to BY DTE Pyromation, Inc. 2-2 Sheath Diameters 316 SS T-442 (4 to 20) m HRT isolated head-mounted 48 1/4 FM/CS explosion-proofapproved DIMETER (inches) T82-00 (4 to 20) m dual input, isolated HRT head-mounted See ordering information in back of section. 2-3 Measuring Junction U Ungrounded 3-0 "S" Dimensions Insert three digit sheath length ("S" Dimension) in inches 5-0 Head Mounting Fittings 4-0 Element Options FP 316 STINLESS STEEL FITTINGS 8HN 8PU4 [1] 1/2" NPT flame-path fitting (1-1/2" "E" length) 1/2" NPT union/nipple with flame-path fitting (specify "E" length in inches, maximum allowable 9") [1] For longer lengths replace "4" with length in inches. Spring-loaded element with flame path HRT is a registered trademark of the HRT Communication Foundation. -6 Phone (260) FX (260) or (800)

7 Single Input Temperature Transmitters for Hazardous Location Explosion-Proof Sensor ssemblies ORDER S Order Number: D U C S(0-200) Transmitter Type 1-2 Input Type 440 [1] (4 to 20) m programmable head-mounted RTD T-642D 00 [1] Unconfigured 1 Thermocouple (TC) 2 RTD (2-wire) 3 RTD (3-wire) 4 RTD (4-wire) (4 to 20) m programmable head-mounted universal (4 to 20) m HRT programmable headmounted universal (4 to 20) m HRT Field Transmitter with explosion-proof aluminum housing FM/ CS / Class I Div I Groups,B,C,D; DIP Class II Div 1 Groups E,F,G; Class III; NI Class I Div II Groups,B,C,D (4 to 20) m HRT Field Transmitter with explosion-proof aluminum housing FM/ CS / Class I Div I Groups B,C,D; DIP Class II Div I Groups E,F,G; Class III; NI Class I Div II Groups B,C,D [1] Only available with 2- or 3-wire input connection and Pt100 sensor type 1-1 Options (For 642 Series only) T D Solid cover Glass cover with digital display Leave blank if using 440, 441, or 442 [1] Default setting supplied as 3-wire Pt100 (0-100) C 1-6 Unit of Measure C Celsius F Fahrenheit 1-5 Range S (lower limit upper limit) 1-4 Failure Mode U Upscale burnout 20.5 m D Downscale burnout 3.8 m 1-3 Sensor Type J Type J thermocouple K Type K thermocouple T Type T thermocouple N Type N thermocouple E Type E thermocouple ohm platinum (α = ºC) For complete specifications see Transmitter Section. HRT is a registered trademark of the HRT Communication Foundation Phone (260) FX (260) or (800)

8 Dual Input Temperature Transmitters for Hazardous Location Explosion-Proof Sensor ssemblies ORDER S Order Number: - D U S(0-200) C Transmitter Type (4 to 20) m HRT Field Transmitter with dual-cavity explosion-proof aluminum housing FM/CS Class I Div I Groups B,C,D; DIP Class II Div I Groups E,F,G; Class III; NI Class I Div II Groups B,C,D T82-00 (4 to 20) m dual input, isolated HRT head-mounted Transmitter 76T82 (4 to 20) m dual input HRT programmable Transmitter with digital display and explosion-proof aluminum housing, FM/CS,NI,IS,,DIP Class I Div I and Div II, Groups,B,C,D 1-1 Housing Cover Options T D D10 Solid cover for 662 series Glass cover with digital display for 662 series Glass cover with digital display for 36T82 and 76T82 series 1-2 Configuration Input 2I Ch1: RTD 2-wire, Ch2: inactive 22 Ch1: RTD 2-wire, Ch2: RTD 2-wire 23 Ch1: RTD 2-wire, Ch2: RTD 3-wire 2T 3I Ch1: RTD 2-wire, Ch2: Thermocouple Ch1: RTD 3-wire, Ch2: inactive 32 Ch1: RTD 3-wire, Ch2: RTD 2-wire 33 Ch1: RTD 3-wire, Ch2: RTD 3-wire 3T 4I 4T TI TT Ch1: RTD 3-wire, Ch2: Thermocouple Ch1: RTD 4-wire, Ch2: inactive Ch1: RTD 4-wire, Ch2: Thermocouple Ch1: Thermocouple, Ch2: inactive Ch1: Thermocouple, Ch2: Thermocouple 1-6 Failure Mode U D 1-5 Input Set-ups 1-7 Range S 0 One Input (662 only) B C D E 1-8 Unit of Measure C F (lower limit upper limit) Celsius Fahrenheit Upscale Burnout 20.5 m Downscale Burnout 3.8 m Process Variable = Ch1; CH2 = inactive Process variable = CH1; secondary variable = Ch2 (T82 Only) Process variable = the difference between CH1 and Ch2 Process variable = the average between CH1 and Ch2 Sensor backup; Process variable= Ch1 and Ch2 1-4 Sensor Input Channel 2 J K T N E Type J thermocouple Type K thermocouple Type T thermocouple Type N thermocouple Type E thermocouple ohm platinum (α = ºC -1 ) 00 No second channel 1-3 Sensor Input Channel 1 For complete specifications see Transmitter Section. J Type J thermocouple K Type K thermocouple T Type T thermocouple N Type N thermocouple E Type E thermocouple ohm platinum (α = ºC -1 ) HRT is a registered trademark of HRT Communication Foundation. -8 Phone (260) FX (260) or (800)

9 Explosion-Proof Connection Heads Connection Head and Transmitter Selection Guide FIGURE B 74 FIGURE C Complete Transmitter FIGURE D Specifications are located in Transmitter Section. Complete Connection Head Specifications are located in the ccessories Section. FIGURE B FIGURE C FIGURE D FIGURE E URE B FIGURE B DIN FIGURE form B C luminum 316L Stainless FIGURE D FIGU FIGURE luminum Explosion-Proof Steel Explosion- FIGURE C FIGURE D Explosion-Proof FIGURE Head, E Group B Proof FIGURE Head, F FIGURE Head, Group FIGURE B Group FIGURE C Temperature Transmitters FIGURE C FIGURE F FIGURE D FIGURE E Programmable head-mounted T-440 Pt100 RTD, X X Only (4 to 20) m analog output T-441 FIGURE C Programmable FIGURE G head-mounted FIGURE H FIGURE I, Thermocouple, isolated, (4 to X X X FIGURE RTD, DOther FIGURE E 20) m analog FIGURE F output RE G FIGURE FIGURE G H Programmable FIGURE FIGURE H I FIGURE I head-mounted FIGURE F FIGURE D FIGURE E FIGURE J H FIGURE I FIGURE J, FIGURE K FIGURE L T-442 Thermocouple, isolated, FIGURE HRT G X FIGURE HX XFIGURE I RTD, Other protocol, (4 to 20) m analog output FIGURE H FIGURE I B T82-00 Thermocouple, RTD, Other (4 to 20) FIGURE m J dual input, isolated HRT head-mounted FIGURE K X X X SPEC NO: FIGURE J FOR: TOLERNCES FOR: Programmable SPEC NO: TITLE: FRCTION DIM PYROMTION = ±1/32" C field, 75T-642, isolated, HRT Thermocouple, SPEC NO: DECIML TITLE: DIM.XX = ±0.010" SIZE: FIGURE IF FIGURE FIGURE G J Unit includes housing and. DECIML CTLOG DIM.XXGE = ±0.005" -8, 77T-662 FIGURE K FIGURE L protocol, RTD, Other B TOLERNCES NGULR SIZE: DIM DWG. = ±2 NO. & S (4 to 20) m FRCTION DIM This = document ±1/32" is PROPRIETRY DRWN analog output TOLERNCES DECIML DIM.XX = ±0.010" Pyromation, Inc. FOR: FIGURE I Programmable FRCTION DIM PYROMTION, = ±1/32" DECIML INC. DIM.XXX = ±0.005" TED LBELS BLFIGURE 8/20/2013 J DRWN BY: D FIGURE K NGULR DIM = field, ±2 HED, WS HED BL B8/7/2013 SPEC NO: DECIML TITLE: DIM.XX = ±0.010" J. BROWN This Bdocument is PROPRIETRY 75T-642, isolated, HRT to DDED FIGURE J, UPDTED LBELS BL 8/20/2013 CTLOG PGE DECIML DIM.XXX = ±0.005" -8, This FIGURES document is PROPRIETRY - K to N BY DTE Pyromation, REPLCED Inc. LL VIEWS, WS HED, WS HED Pyromation, Inc. BL 8/7/2013 FORT protocol, = 77T-662 w/ Thermocouple, NGULR SIZE: Unit includes DIM DWG. housing ±2 NO. & SHEET NO: REV. REV and. BY DTE (4 to 20) m display RTD, TOLERNCES Other This document is PROPRIETRY to analog output Pyromation, B Inc. FORT WYNE, INDIN FRCTION DIM = ±1/32" with digital DRWN BY: DTE: DECIML DIM.XX = ±0.010" display J. BROWN 4/25/2011 DECIML DIM.XXX = ±0.005" (4 to 20) m NGULR DIM = ±2 dual input This document is PROPRIETRY HRT Field to FOR: Pyromation, Inc. Transmitter with FORT B WYNE, INDIN T82-D10 Thermocouple, PYROMTION, INC. Unit includes housing and. digital display SPEC NO: TITLE: RTD, Other CTLOG PGE and -8, explosionproof housing, FIGURES - K S BL 8/20/2013 SIZE: DWG. NO. & SHEET NO: REV. S HED BL 8/7/2013 Group This document is PROPRIETRY to TOLERNCES BY DTE Pyromation, Inc. FIGURE B HRT M is a registered trademark FIGURE N of the HRT Communication Foundation. FRCTION DIM = ±1/32" DRWN BY: DTE: DECIML DIM.XX = ±0.010" J. BROWN 4/25/2011 DECIML DIM.XXX = ±0.005" NGULR DIM = ±2 B This document is PROPRIETRY to Phone (260) FX (260) or (800) Pyromation, Inc. FORT WYNE, INDIN FIG FIGUR FIG B2738

10 Overview of NEC Hazardous Location Classifications and Methods of Protection Classes Class I Groups s Divisions 1 2 Location in which flammable gases or vapors are or may be present in the air in quantities sufficient to produce explosive or ignitable mixtures. Group : cetylene Group B: Hydrogen Group C: Ethylene Group D: Propane, fuels, solvents Locations where hazardous material exists under normal operating conditions or through breakdown or repair. Locations where hazardous materials are expected to be confined within closed containers of closed systems but may become present through a leak or process failure. Class II s Locations that are hazardous because of the presence of combustible dust. E: Metal dusts F: Carbon dust G: Combustible dust, flour, grain, wood, plastic, chemicals Combustible dust is in the air under normal operating conditions in quantities sufficient to produce explosive or ignitable mixtures or through breakdown or repair. Combustible dust may be in the air in sufficient quantities to produce an explosion due to abnormal operations or failure of electrical equipment. Class III Locations that are hazardous because of the presence of easily ignitable fibers or flyings, but in which such fibers or flyings are not likely to be in suspension in the air in quantities sufficient to produce ignitable mixtures. There are no defined groups. s are textiles, woodworking, paper fibers. Easily ignitable fibers or materials producing combustible flyings are handled, manufactured, or used. Easily ignitable fibers are stored or handled other than in the process of manufacture. Methods of Protection Explosionproof () Class I, Division 1, 2 Dust-Ignitionproof (DIP) Class II, Division 1, 2 Intrinsically Safe (IS) Class I, Division 1, 2 Class II, Division 1, 2 Class III, Division 1, 2 Nonincendive (NI) Class I, Division 2 Class II, Division 2 Class III, Division 1, 2 pparatus enclosed in a case that is capable of withstanding an explosion of a specified gas or vapor that may occur within it and of preventing the ignition of a specified gas or vapor surrounding the enclosure by sparks, flashes, or explosion of the gas or vapor within, and that operates at such an external temperature that a surrounding flammable atmosphere will not be ignited thereby. Equipment enclosed in a manner that excludes dust and does not permit arcs, sparks, or heat otherwise generated or liberated inside of the enclosure to cause ignition of exterior accumulations or atmospheric suspensions of a specified dust on or in the vicinity of the enclosure. Equipment not capable of releasing sufficient electrical or thermal energy under normal or abnormal conditions to cause ignition of a specific flammable or combustible atmospheric mixture in its most easily ignitable concentration. Equipment having electrical circuitry that is incapable, under normal operating conditions, of causing ignition of a specified flammable gas-air, vapor-air, or dust-air mixture due to arcing or thermal means. This material is for reference only. Refer to The NEC 2005 Handbook, NFP 70: National Electrical Code International Electrical Code Series (Quincy, M, 2005) for authoritative and complete documentation. -10 Phone (260) FX (260) or (800)