70 mm Electric Ducted Fan Power System
|
|
- Millicent Darleen Marsh
- 6 years ago
- Views:
Transcription
1 70 mm Electric Ducted Fan Power System WARNING!! Please read instruction manual before assembly This fan is not a toy. It can be very dangerous and may cause serious damage to people and property. All novice or beginners should seek help from an expert. Please read all instructions and have an experienced flyer inspect your fan prior to flying. Model data Outside Diameter : 73.20mm Rotor Diameter : 69mm 5 blades Weight : 85g all parts with intake lip Motor Shaft : 2.3 / 3.0 / 3.17 / 4.0 mm Rotor Shaft : 6.10mm Motors required : 29mm or Static thrust at max power: 10N Recommended Motor : MEGA 16/25/2 or Typhoon EDF, Hacker etc. AP-700DF is the fun unit which is made with the best material and strict quality control to insure that it provides the best performance for its entire users. Maximum static thrust High efficiency at all speeds 1
2 For the motive force of this Fan, we recommend brushless motors with the KV for the maximum performance. The output performance will depend on the motor and battery used with this fan unit. The motor mount housing will fit a motor with the maximum diameter of 29 mm or 400~480. Introduction Thank you for purchasing the AirPower AP-700DF Electric Ducted Fan. As you will see this is an extremely easy to build fan but as it is not a beginner's model, we would suggest some flying experience is required. These instructions are a guide and we assume you have assembled kits before. If you need help please ask an experienced person for advice. NOTE: THIS IS NOT A TOY.. Parts check 1. Fan Seat x mm Rotor x 1 3. Spinner x 1 4. Intake Lip x 1 5. Adapter Shaft x 1 6. Screw M3 x 2 7. Spacer x 2 8. Install tools x 1 9. Instructions Manual x 1 2
3 Installation Step1: Cut off extra stump that you will find in center of Motor Mound. If this piece is not removed completely, it will affect fan installation in future steps. (Picture 1) Step2: We highly recommend before placing motor into its mound, place a temporary sheet of white of white paper around the motor. This will help the motor be place directly in the center of mound. (Picture 2, 3, 4) P.1 Remove extra Stump. P.2 Wrap white sheet of pape around motor several times P.3 Place motor into the tube. Please make sure P.4 Push motor to the end completely there are no gaps Step3: After you place motor into the motortube, adjust motor to make sure that the holes found in the motor mount plate line up. Use the M3 screws with washers to secure the motor to the plate. Make sure to evely tighten the screws. Screws, washers and tools are provided to you free in your assembly kit. (Picture 5, 6) P.5 Line up the motor screw holes with those P.6 Evenly tightened both screws. in the motor tube. Step X: Remove temporary white paper you placed in step 2, after screw tightening. 3
4 Step4: Fan installation 1 (Caution: You must balance fan to help increase life of the motor, and also will increase output efficiency) We also recommend fans be sanded, trimmed, and balanced. With out this step the fan blade may rub against the duct. (Picture 7, 8) P.7 Sand and trim fan blade. P.8 We recommend using a balancer to balance fan unit. Step5: Fan installation 2 (Caution do not apply to much force when tightening nut and fan blade, make sure hand is placed in right position to avoid finger injury or damage of fan blade) (Picture 12) P.9 Place shaft into motor. P.10 Place fan blade into shaft. P.11 Place washer followed by nut P.12 Tightened nut (Caution do not apply) to much force when tightening nut and fan blade, make sure hand is placed in right position to avoid finger injury or damage of fan blade. Please pay attention to hand position to avoid hand injury. 4
5 Step6: Place nose cone into the motor shaft. Tighten by using a coin. (Picture 13, 14) P.13 Place nose cone into motor shaft P.14 Tighten with a coin. Step7: Trim edge of duct for accurate fit into intake. If necessary you may use glue to afix duct to intake ring. (Picture 15, 16) P.15 Trim edge of duct for accurate fit. P.16 Adjust duct to fit into intake. P.17 You might use glue to fix duct P.18 Refer to picture for complete assembly into intake. unit. ** If need the manual of the colored edition, please link the download of our website. 5
Schübeler DS-DIA Ducted Fan Series Manual
Schübeler DS-DIA Ducted Fan Series Manual Manual for the following fan units: DS-26-DIA HDT DS-30-DIA HDT DS-44-DIA HDT DS-51-DIA HDT DS-75-DIA HDT DS-94-DIA HDT Safety instructions (Read before first
More informationELECTRIC DUCTED FAN INSTRUCTION MANUAL
ELECTRIC DUCTED FAN INSTRUCTION MANUAL Technical Data Fan Swept Area: 2.71 in 2 [17.5cm 2 ] Maximum rpm: 50,000 rpm Housing Inner Diameter: 2.14 in [54.5mm] Outer Diameter: 2.23 in [56mm] Complete Assembly
More informationRequires: 4-channel radio w/ 4 micro servos, Outrunner Motor KM A brushless ESC, 3 cells 11.1V 2100 mah Li - Po battery & charger.
INSTRUCTION MANUAL (E196B) Requires: -channel radio w/ micro servos, Outrunner Motor KM083800 0A brushless ESC, 3 cells 11.1V 100 mah Li - Po battery & charger. Wing Span Wing Area Flying Weight Fuselage
More informationFRL 10 Centrifugal blowers
FRL 10 Centrifugal blowers User instructions 2 Kongskilde Blower model FRL10. Motor mounting instructions Motor Specifications: Model FRL 10 Blower/Aspirator fans are designed to be driven by Single or
More informationModels , Equinox, and Sirens Clutch Replacement Service Manual
Models 2001-130, Equinox, and 508-128 Sirens Clutch Replacement Service Manual 25500297 Rev. A0 1115 Printed in U.S.A. Copyright 2015 Federal Signal Corporation Contents Safety Messages... 3 General Description...
More informationRequires : 4-channel radio w/ 4 micro servos, Outrunner Motor w/ Propeller Adaptor 20A Brushless ESC, 3 cells 11.1V 2100mAh Li - Po battery & charger.
INSTRUCTION MANUAL Requires : -channel radio w/ micro servos, Outrunner Motor w/ Propeller Adaptor 0A Brushless ESC, 3 cells 11.1V 100mAh Li - Po battery & charger. Specifications Wing Span Wing Area Flying
More informationSpecifications. Before commencing assembly, please read these instructions thoroughly. INSTRUCTION MANUAL
INSTRUCTION MANUAL Before commencing assembly, please read these instructions thoroughly. Specifications Wing Span: 60 in / 155 mm Wing Area: 60 sq in / 40 sq dm Flying Weight: 3.7 lbs / 1680 g Fuselage
More informationCLUB SERIES ADJUSTABLE AB BENCH
CLUB SERIES ADJUSTABLE AB BENCH ASSEMBLY INSTRUCTIONS Part # 73030 Rev C. Revision: /8/0 PARTS LIST KEY 3 5 6 7 8 9 0 PART # AP0-003 P0-00 AP0-00 AP0-00 AP0-003 P07-0005 P07-000 AP0-003 DAC038706NU DAC0380686NU
More informationMODEL SK2750. COMPRESSOR SERVICE KIT For use on 2750 Series Compressors
MODEL SK2750 COMPRESSOR SERVICE KIT For use on 2750 Series Compressors WARNING: Unplug the compressor before beginning disassembly. CAUTION: Improper assembly or use of damaged parts may lead to premature
More informationINLET DAMPER WALL FAN UNIT
FARM PRODUCTS DIVISION MEMBER OF AMCA AMERICAN COOLAIR CORPORATION P.O. BOX 2300 JACKSONVILLE, FLORIDA 32203 PHONE (904) 389-3646 FAX (904) 387-3449 E-MAIL - agfans@coolair.com INLET DAMPER WALL FAN UNIT
More informationSuper Sports Senior- 90
INSTRUCTION MANUAL Super Sports Senior- 90 0.9 cubic inch displacement - stroke (glow) Radio required: - channel radio w 5 servos Wing Span Wing Area Flying Length Fuselage Length Specifications in / 050mm
More informationICED CAPPUCCINO MACHINE Taylor MODEL: 390
4.8.6.3 ICED CAPPUCCINO MACHINE Taylor MODEL: 390 LOCATION: Front of House WHEN CLEANED: Daily, Weekly, Monthly, Seasonal TOOLS/SUPPLIES REQUIRED: Salmon Cloth 2 or 3-Compartment Sink Sink Detergent Sanitizer
More informationOWNERS MANUAL FOR MEC 300E ATA
OWNERS MANUAL FOR MEC 300E ATA PLEASE READ AND FULLY UNDERSTAND THE INSTRUCTIONS PRIOR TO SETTING OR TUNING THE MACHINE. CAUTION: ANY MEC CLAY TARGET MACHINE MUST BE IN THE DISARMED STATE WITH THE BATTERY
More informationThe World Models. Manufacturing Co., LTD. The World Models. Manufacturing Co., LTD.
INSTRUCTION MANUAL Dago Red Mustang-46 A L M O S T- R E A D Y- T O - F LY 0.40-0.46Cubicinchdisplacement2-stroke 0.70-0.81 Cubicinchdisplacement4-stroke Require s : 5-channel radio w/ 5 standard servos
More informationPERFECT FIT IN-DASH HEAT/ COOL/ DEFROST EARLY 1955 CHEVROLET PICKUP
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1947 - EARLY 1955 CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on
More informationEnglish BT3600
www.blackanddecker.com 3 English BT3600 FIG. 1 FIG. 2 150mm BENCH GRINDER BT3600 GENERAL SAFETY RULES WARNING: Read all instructions. Failure to follow all instructions listed below may result in electric
More informationPREMIUM KITCHEN MIXER TAP. PREMIUM KITCHEN MIXER TAP Assembly, operating and safety instructions IAN
PREMIUM KITCHEN MIXER TAP PREMIUM KITCHEN MIXER TAP Assembly, operating and safety instructions IAN 282471 GB/IE/NI Assembly, operating and safety instructions Page 5 B 15mm HG00476A HG00476B C 5 4 12
More informationCOOLING SYSTEM 1. Section V CONTENTS DATA AND SPECIFICATIONS. Page. Fluid Fan Drive (Silent Flite) 3. Water Pump 4. Radiator 5
Section V COOLING SYSTEM CONTENTS Fluid Fan Drive (Silent Flite) 3 Water Pump 4 Radiator 5 Water Temperature Gauge 6 Thermostat 7 Radiator Pressure Cap 7 Service Diagnosis 7 DATA AND SPECIFICATIONS COOLING
More informationModel Series. PumpAgents.com - buy pumps and parts online QUIET - FLUSH ELECTRIC TOILET. Model Series FEATURES SPECIFICATIONS INSTALLATION
PumpAgents.com - Click here for Pricing/Ordering Model 37045-Series QUIET - FLUSH ELECTRIC TOILET FEATURES Very quiet flush cycle - like a household toilet Single button flush actuator - with dual function
More informationMNEFDD54 & MNBCDD54 GALVANIZED WALL FANS Installation, Operation, and Maintenance Instructions
FARM PRODUCTS DIVISION MEMBER OF AMCA AMERICAN COOLAIR CORPORATION P.O. BOX 2300 JACKSONVILLE, FLORIDA 32203 PHONE (904) 389-3646 FAX (904) 387-3449 E-MAIL - fans@coolair.com MNEFDD54 & MNBCDD54 GALVANIZED
More informationFLECK 5600 WATER SOFTENER INSTALLATION
FLECK 5600 WATER SOFTENER INSTALLATION Discount Water Softeners recommends using a licensed plumber to install your water softener. The following installation instructions are for use with the water softener
More informationMODEL SK2660 COMPRESSOR SERVICE KIT. For use on 2660 and 2680 Model Compressors
MODEL SK2660 COMPRESSOR SERVICE KIT For use on 2660 and 2680 Model Compressors WARNING: Unplug the compressor before beginning disassembly. CAUTION: Improper assembly or use of damaged parts may lead to
More informationOP44-1 REV 2: Removed depiction of air intake hole in the CB-907A Right Aft Case Baffle.
REVISION DESCRIPTION: OP44-1 REV 2: Removed depiction of air intake hole in the CB-907A Right Aft Case Baffle. OP44-4 REV 1: Steps rewritten to describe the air intake hole on the CB-907A Right Aft Case
More informationMODEL SK2660 COMPRESSOR SERVICE KIT. For use on 2660 and 2680 Model Compressors
MODEL SK2660 COMPRESSOR SERVICE KIT For use on 2660 and 2680 Model Compressors WARNING: Unplug the compressor before beginning disassembly. CAUTION: Improper assembly or use of damaged parts may lead to
More information52 CEILING FAN READ AND SAVE THESE INSTRUCTIONS FAN RATING AC 120V.
Irene 52 CEILING FAN READ AND SAVE THESE INSTRUCTIONS FAN RATING AC 120V. 60Hz TABLE OF CONTENTS Tools and Materials Required... 1 Package Contents... 1 Safety Rules... 2 Mounting Options... 3 Hanging
More informationREAD AND SAVE THESE INSTRUCTIONS
Instruction Manual 45cm Pedestal Fan Model: PED45CG READ AND SAVE THESE INSTRUCTIONS Please read and follow the instructions in this user manual even if you feel you are familiar with the product, and
More informationSpeaker Wall Mount (MSP-DCCSPM)
INSTALLATION INSTRUCTIONS Speaker Wall Mount () The speaker wall mount is a convenient mounting solution for speakers that are compatible with flat panel displays. The speaker wall bracket is equipped
More informationSkyLink cu. in. displacement 2-stroke. Requires : 5-channel radio w/ 7 standard servos. Specifications
INSTRUCTION MANUAL SkyLink 0 0.0-0.55 cu. in. displacement -stroke Requires : 5-channel radio w/ 7 standard servos Specifications Wing Span Wing Area Flying Weight Fuselage Length 66 in / 1680 mm 590 sq
More information#PSBTWE1000 INSTALLATION GUIDE
Electronic Bidet with Integrated Toilet #PSBTWE1000 INSTALLATION GUIDE INSTALLATION MANUAL Thank you for choosing our product! Please read and carefully follow the instructions before installation. Secure
More informationSERVICING INFORMATION
SERVICING INFORMATION OPTIKINETICS SOLAR 250 (Early Type) M.Ginda 06/03/08 1 Servicing the Solar 250 effects projector. This is a short guide on how to service the main component parts of the projector.
More informationUSSC LLC 4 ONE LLC FIELD MODIFICATION INSTRUCTIONS
and Retrofit of G2E Quick Release Cushion Upholstery 1 OF 32 A 1.0 PURPOSE: To replace both Back and Cushion Upholstery on the G2E seats. 2.0 Tools Required: 2.1 1/2 Socket and Wrench 2.2 5/8 Socket 2.3
More informationNM952 SERVICE PARTS TABLE OF CONTENTS. Cabinet Air Cooled Refrigeration Water Cooled Refrigeration Water System Gearmotor...
This parts list contains the service parts and wiring diagrams for this model. Check the model number in question to be sure that it is applicable to this parts list. NM9 SERVICE PARTS TABLE OF CONTENTS
More informationAPW PSI PRESSURE WASHER
APW5001 1300 PSI PRESSURE WASHER 1300 PSI PRESSURE WASHER Please carefully read this manual which has been specifically designed to provide all the necessary information for the correct use of the machine,
More informationHeater Upgrade Instructions
Heater Upgrade Instructions Important Safety Precautions It is recommended that you plug the chiller into a GFCI outlet at all times. Do not operate SeaChill chillers or any accessory to SeaChill chillers
More information#8 STAINLESS STEEL ELECTRIC MEAT GRINDER OWNER S MANUAL
#8 STAINLESS STEEL ELECTRIC MEAT GRINDER OWNER S MANUAL ITEM# 337989 Thank you very much for choosing a Kitchener product! For future reference, please complete the owner s record below: Model: Purchase
More informationMill, Microcut Grinder STANDARD OPERATING PROCEDURE
STANDARD OPERATING PROCEDURE Mill, Microcut Grinder Model: MC-15 Manufacturer: Stephan Machinery, Inc. Location: Wet Processing Pilot Plant, 1091 Food Sciences Building Publication Date: 07/23/2014 Iowa
More informationATD PEDESTAL FAN INSTRUCTIONS
ATD-30330 30 PEDESTAL FAN INSTRUCTIONS Item No. Blade Diameter Voltage / Hz Current (A) ATD-30330 30 120V /60Hz 1.4 READ AND SAVE THESE INSTRUCTIONS Failure to properly follow these instructions may lead
More informationIMPORTANT SAFETY RULES
1 IMPORTANT SAFETY RULES Wood working can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product.
More informationOWNERS INSTRUCTION MANUAL
OWNERS INSTRUCTION MANUAL 132CM/52 Classic INSTALLATION OPERATION MAINTENANCE CAUTION READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION. IF UNSURE CONSULT A QUALIFIED ELECTRICIAN SUITABLE
More informationREAD AND SAVE THESE INSTRUCTIONS
145x210mm FW40-6HR Black 365 20150613 Easy living OWNER S MANUAL 16" Wall Fan MODEL: RM/288 Version 1.0 2015 READ AND SAVE THESE INSTRUCTIONS Attention: Pictures in the IM are for reference only. CAUTION
More informationultra quiet fan USER MANUAL INSTALLATION OPERATION MAINTENANCE
USER MANUAL ultra quiet fan INSTALLATION OPERATION MAINTENANCE Z0414808 rev A ISSUED 02/2014 READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT. safety and handling Safety Warning
More informationFAN ENGINEERING. Sealing of Fan Housings
FAN ENGINEERING Information and Recommendations for the Engineer FE-700 Sealing of Fan Housings Introduction A variety of options are offered by fan manufacturers to seal fan housings. Sealing the housing
More informationBUBBLE-Maker. Necessary tools and materials:
106.326 BUBBLE-Maker Necessary tools and materials: Fretsaw and board Wood file, glasspaper Pillar drill Hole maker 2mm dia.+ 3.5mm Cross and normal screwdriver Allen key ( 7mm ) Wood glue, all purpose
More informationInstruction Sheet. DANGER Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.
Instruction Sheet DOC306.53.00742 Safety information Please read this entire document before unpacking, setting up or operating this equipment. Pay attention to all danger and caution statements. Failure
More informationPERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1968 CHEVROLET IMPALA
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1968 CHEVROLET IMPALA CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationNOTE ITEM PART NUMBER KIT CONTENTS QTY
R22-series Cabin Heater Upgrade Installation Kit Instructions Applicable to helicopter S/N 4782 and prior equipped with cabin heater. Kit upgrades heater installation to scroll-air intake. For use with
More information400KV Van de Graaff Generator Kit Builders Manual
400KV Van de Graaff Generator Kit Builders Manual 400KV Design Photos Introduction: Welcome to perhaps what will be your first VDG kit. This manual is designed to give you a very straight forward and streamlined
More informationINSTRUCTION MANUAL with Replacement Parts
INSTRUCTION MANUAL with Replacement Parts MODEL FD500 FOOD WASTE DISPOSERS (INCLUDES MOTOR PARTS) ML-18978 A product of HOBART CORPORATION 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 FORM 11394 Rev. G (10-98)
More informationInstallation Instructions ZUG30 Heater Kit/Cover
Installation Instructions ZUG30 Heater Kit/Cover TO BE USED WITH HOUSEHOLD REFRIGERATORS 30" BUILT-IN BOTTOM-FREEZER, 2 DRAWER Unit 1 - Spacer Clips Installed Unit 2 - Heater Installed ALL REFERENCES TO
More informationInstallation Guide. Model: IC15- MF Model: IC15- MFSilent Model: IC30- MF Model: IC30- MFSilent
Installation Guide Model: IC15- MF Model: IC15- MFSilent Model: IC30- MF Model: IC30- MFSilent IMPORTANT SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC
More informationSELF-PRIMING CENTRIFUGAL PUMPS BMLS-M & BMLS-H
SELF-PRIMING CENTRIFUGAL PUMPS BMLS-M & BMLS-H INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS HP Phase Medium Head High Head 3 1 BMLS 300 M BMLS 300 H 3 3 BMLS 300 M3 BMLS 300 H3 5 1 BMLS 500 M BMLS
More informationTRW-17 READ PRIOR TO UNPACKAGING COMPONENTS
Rotary Woofer Setup & Installation Guide for the Eminent Technology Model TRW-17 READ PRIOR TO UNPACKAGING COMPONENTS Contents: 1) Removing Rotary Woofer Stand (optional) from Shipping Crate 2) Removing
More informationBe sure the siren amplifier and speaker(s) in your installation have compatible wattage ratings.
Model RB-CAP11 Mounting Kit for the Rumbler Speaker in a 2011 and Newer Chevy Caprice 2562648A REV. A 1011 Safety Message to Installers of Siren Speakers People s lives depend on your proper installation
More informationMANUFACTURING NUMBERS: CORN CAROUSEL. Model CC-19 Series P/N /99. Owner s Manual
MANUFACTURING NUMBERS: 9500410 9500412 C US Model CC-19 Series 9500400 P/N 1010730 10/99 Owner s Manual A.J. Antunes & Co. Owner Information...1 General...1 Warranty Information...1 Service/Technical Assistance...2
More informationHeating and ventilation system,
Page 1 of 24 87-151 Heating and ventilation system, servicing Instrument panel air outlets and air guide ducts CAUTION! Before working on the electrical system: Obtain security code for anti-theft radio.
More informationMarley Ultra Quiet Fan
USER MANUAL Marley Ultra Quiet Fan DESIGNED FOR INDUCED-DRAFT COOLING TOWER APPLICATIONS M2012-1165 ISSUED 8/2012 READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT. safety and
More informationFleck 5600 SXT. Installation Guide. Make a list of all of the plumbing fittings needed to install; a typical list looks like this:
Installation Guide Before you assemble your new system, be sure that the following conditions have been met for placement of your softener: Getting Started Level, firm surface, such as concrete, on which
More informationSAND FILTER PUMP MANUAL
SFP7-16-GB SAND FILTER PUMP MANUAL 290729XX / 290730XX Product specifications Model 290729XX 290730XX Maximum operating
More informationUser s Manual and Operating Instructions
User s Manual and Operating Instructions Model Numbers: PT-18W-DDF-A, PT-20F-DDF-A, PT-20S-DDF, PT-24O-DDF, PT-24-DDF, PT-24-DDF-F, PT-30-DDF, PT-30P-DDF-A, PT-30P-DDF-AF READ AND SAVE THESE INSTRUCTIONS
More informationPERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST CHEVROLET CHEVELLE/ EL CAMINO NOTE: INSTRUCTIONS DEPICT CHEVELLE
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT SERIES IN-DASH HEAT/ COOL/ DEFROST 1964-65 CHEVROLET CHEVELLE/ EL CAMINO NOTE: INSTRUCTIONS DEPICT CHEVELLE CONTROL
More informationService Bulletin Trucks Date Number Page
Mack Trucks, Inc. Allentown, PA USA (Does not apply to Mack Trucks Australia) (Supersedes SB215025 dated 03/27/07) Service Bulletin Trucks Date Number Page 11/04/08 SB215025 1(25) Cooling System Revisions
More informationTRUSTY PRODUCTS, INC.
TRUSTY PRODUCTS, INC. 137 S. 8 th Avenue, #D, City of Industry, CA 91746 Tel: (626) 333-2221 Fax: (626) 333-2466 D.C. 12V CEILING FAN INSTALLATION INSTRUCTIONS V002-RC QUESTIONS OR CONCERNS CONTACT TRUSTY
More informationF-P, F-L, FT-P AND FT-L SERIES 2/3 JACKETED DIRECT STEAM TILTING & STATIONARY KETTLES PARTS AND SERVICE MANUAL
F-P, F-L, FT-P AND FT-L SERIES 2/3 JACKETED DIRECT STEAM TILTING & STATIONARY KETTLES PARTS AND SERVICE MANUAL EFFECTIVE NOVEMBER 2, 2015 Superseding All Previous Parts Lists. The Company reserves the
More informationFLUSH WATER SAVER DUAL FLUSH KIT
FLUSH CH ICE Version 12.26.08 FC002 WATER SAVER DUAL FLUSH KIT Dear Consumer; You have purchased a high quality water saver dual flush toilet valve kit. Every care has been taken during manufacturing to
More informationDisposal Unit (BKSDU) Burger King Shortening. Operation, Service & Parts Manual BURGER KING BKSDU
BURGER KING BKSDU Burger King Shortening Disposal Unit (BKSDU) Operation, Service & Parts Manual Frymaster, a member of the Commercial Food Equipment Service Association, recommends using CFESA Certified
More informationBK AND BKT BLOWER ACCESSORY INSTALLATION INSTRUCTIONS
BK AND BKT BLOWER ACCESSORY INSTALLATION INSTRUCTIONS MODEL BK MANUALLY CONTROLLED BLOWER MODEL BKT THERMOSTATICALLY CONTROLLED BLOWER WARNING: ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped
More informationTCC 2700 Laminating Machine Operating Instructions
TCC 2700 Laminating Machine Operating Instructions Remove machine from carton and place on a stable surface. Remove machine from plastic bag Remove bubble-wrap from mandrills TCC 2700 Laminating Machine
More information12 VELOCITY OWNER S MANUAL OPERATING INSTRUCTIONS - MAINTENANCE - SAFETY - TROUBLESHOOTING
12 VELOCITY OWNER S MANUAL OPERATING INSTRUCTIONS - MAINTENANCE - SAFETY - TROUBLESHOOTING This manual contains very important safety warnings and information. Read and save these instructions for future
More informationThe Marine Throne. Model TMT S/37045/X-Series QUIET - FLUSH ELECTRIC TOILET. "all the comforts of home" FEATURES SPECIFICATIONS INSTALLATION
The Marine Throne "all the comforts of home" Model TMT S/37045/X-Series QUIET - FLUSH ELECTRIC TOILET FEATURES Very quiet flush cycle - like a household toilet Single button flush actuator - with dual
More informationPERFECT FIT IN-DASH HEAT/ COOL/ DEFROST FORD PICKUP
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1960-66 FORD PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
More informationPentz EF5 Installation Guide
Pentz EF5 Installation Guide Clear Vue Cyclones 145 Nix Road Liberty, SC 29657 888-299-0221 www.clearvuecyclones.com Disclaimers & Warnings WARNING: All persons, by purchasing a motorized dust collection
More informationMarley X7 Fan USER MANUAL DESIGNED FOR INDUCED-DRAFT COOLING TOWER APPLICATIONS
USER MANUAL Marley X7 Fan DESIGNED FOR INDUCED-DRAFT COOLING TOWER APPLICATIONS M2010-1234A ISSUED 3/2012 READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT. Fan Components 1
More informationInstallation Manual PS-200 & PS-201
Installation Manual PS-200 & PS-201 Table of Contents Pre-Uncrating Checklist... 1 Verifying System Requirements... 2 Verifying System Direction... 2 Verifying the Electrical Requirements... 2 Removal
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BUILT-IN BOTTOM MOUNT REFRIGERATOR/FREEZER DBRTGK72SS-GRILLE KIT (FOR designer SERIES ONLY) VIKING RANGE CORPORATION 111 Front Street Greenwood, Mississippi (MS) 38930 USA (662)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS St. George / Wyatt / Seagram One-Piece Toilets St. George 1.28 gpf / 4.8 Lpf - Model# D22000C101 Wyatt 1.28 gpf / 4.8 Lpf - Model# D22005C101 Seagram 1.28 gpf / 4.8 Lpf - Model#
More informationC-IV 60 CEILING FAN READ AND SAVE THESE INSTRUCTIONS. FAN RATING AC 120V. 60Hz
C-IV 60 CEILING FAN READ AND SAVE THESE INSTRUCTIONS FAN RATING AC 120V. 60Hz Please do not use any electric or battery powered tools in the assembly and installation of this or any Matthews Fan Company
More informationBurn Easy Installation Instructions LP or Natural Gas Fired Units. Cremator Setup:
Burn Easy Installation Instructions LP or Natural Gas Fired Units Cremator Setup: 1. Place cremator, outdoor on a solid base consisting of concrete or gravel. Keep this site free of all vegetation. Combustibles
More informationPlease read the following installation instructions first after purchasing this product or transporting it to another location.
9 Installation Overview Please read the following installation instructions first after purchasing this product or transporting it to another location. 1 Unpacking your refrigerator 2 Choosing the proper
More informationHeater with Air Conditioning. E-Series Ford Aeromaster
Service Guide Heater with Air Conditioning E-Series Ford Aeromaster Contents Blower Motor...2 Plenum Removal...3 Control Module...6 Servo Motors...8 Coolant Valve and Servo Motor...8 Evaporator Recirculation
More informationMAINTENANCE MANUAL TAIYO SEIKI CO., LTD.
MAINTENANCE MANUAL TAIYO SEIKI CO., LTD. Introduction This Maintenance Manual explains how to replace and adjust the major components of the Automatic Taping Machine when required in daily operation.
More informationWARNING. Before installing your siding, inspect the delivered wood. All installed material shall be considered accepted.
INSTALLATION GUIDE WARNING This guide contains important information that must be read prior to installing your siding. Failure to comply with any of the following points MAY VOID YOUR WARRANTY. Be sure
More informationINSTALLATION INSTRUCTIONS TOOLS YOU WILL NEED GETTING STARTED
INSTALLATION INSTRUCTIONS HONEYCOMB SHADES STANDARD RECTANGULAR Thank you for your purchase. This shade has been custom built for you from the highest quality materials. To avoid errors and save valuable
More informationMAT12PDDAW : 01 - CONTROL PANEL [1/10] Ref # Part Number Qty. Description FACIA, PD/PS (CONTROL PANEL) SCREW, CONTROL PANEL 3
MAT12PDDAW : 01 - CONTROL PANEL [1/10] Page 1 of 20 MAT12PDDAW : 01 - CONTROL PANEL [1/10] Ref # Part Number Qty. Description 1 22004305 1 FACIA, PD/PS (CONTROL PANEL) 2 215506 4 SCREW, CONTROL PANEL 3
More informationInstallation Manual PS-225 & PS-275
Installation Manual PS-225 & PS-275 Table of Contents Pre-Uncrating Checklist... 1 Verifying System Requirements... 2 Verifying System Direction... 2 Verifying the Electrical Requirements... 2 Removal
More informationUse & Care Manual Electric Portrait with remote control DBL-2000-DD5
Use & Care Manual Electric Portrait with remote control DBL-2000-DD5 These instructions are for your safety. Please read through them thoroughly before use and retain for future reference. Failure to follow
More informationWARNING: ELECTRICAL GROUNDING INSTRUCTIONS
BK AND BKT BLOWER ACCESSORY INSTALLATION INSTRUCTIONS Model BK Manually led Blower Model BKT Thermostatically led Blower WARNING: ELECTRICAL GROUNDING INSTRUCTIONS This appliance is equipped with a three-prong
More informationMassage Bathtub Instructions of Installation. MODEL:MT-RT1708 SIZE:1700*800*620mm
Massage Bathtub Instructions of Installation MODEL:MT-RT1708 SIZE:1700*800*620mm Preparations Dear Customer, Thank you for choosing our product. For your safe concern, please take a few minutes to read
More informationTwo Tier Illumifalls Patio Pond
Two Tier Illumifalls Patio Pond REMINDER CALL 1-888-755-4497 BEFORE RETURNING TO STORE. Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-888-755-4497,
More informationFood Waste Disposer Instruction Manual
Food Waste Disposer Instruction Manual See insert for specific information about your new disposer NOTE: IMPORTANT: CAUTION: This Food Waste Disposer has been designed to operate on 110-120 Volt, 60 Hz
More information52 BERKSHIRE CEILING FAN
52 BERKSHIRE CEILING FAN Owner s Manual Models #20223, 20224 If a problem cannot be remedied or you are experiencing difficulty in installation, please contact the Service Department: 1-877-459-3267, 9
More informationDISTRIBUTION > HOUSING, HVAC > INSTALLATION > AIR INLET HOUSING
Page 1 of 6 Service Manual: HEATING & AIR CONDITIONING - Print Date: SERVICE INFORMATION - 2500 HD & 3500 HD DISTRIBUTION > HOUSING, HVAC > INSTALLATION > AIR INLET HOUSING Fig 1: Front Of Air Inlet Housing
More informationHydroCycle Vertical Aeroponic Systems
HydroCycle Vertical Aeroponic Systems 2018 Growers Supply All Rights Reserved. Reproduction is prohibited without permission. *Actual system may differ from system shown. 113593 8' Vertical System (44
More informationINSTALLATION, OPERATION, AND MAINTENANCE MANUAL
INSTALLATION, OPERATION, AND MAINTENANCE MANUAL TUBE AXIAL FANS BTA, WTA, HTA, DDA The purpose of this manual is to aid in the proper installation and operation of the fans. These instructions are intended
More informationRequires: 80 cc gasoline engine, 4-channel radio w/ 6 standard servos. Specifications. * Specifications are subject to change without notice.
INSTRUCTION MANUAL 1/3 CLIPPED WING CUB Requires: 80 cc gasoline engine, -channel radio w/ 6 standard servos. Specifications Wing Span Wing Area Flying Weight Fuselage Length 10 in / 3050 mm 0 sq in /
More informationTorrena 42 Ceiling Fan
Torrena 42 Ceiling Fan Owner s Manual Part # 269268, 269269 Model # 32096, 32097 Exclusively Distributed by: HD Supply Facilities Maintenance, Ltd. Atlanta, GA 30339 2017 Made in China If you are experiencing
More informationINTRODUCTION: COOLING TOWER INTRODUCTION: COOLING TOWER FANS. The cooling Tower is commissioned since 2006 and 1 st failure was encountered in 2007
INTRODUCTION: COOLING TOWER The cooling Tower is commissioned since 2006 and 1 st failure was encountered in 2007 The cooling tower is designed to cool the sea water coming from various heat exchangers
More informationWarranty Details page 2. Pump Description & Technical page 3 Specifications. Transportation, Storage & Installation page 4. Pump Maintenance page 5
5 . Manual Contents Warranty Details page 2 Pump Description & Technical page 3 Specifications Transportation, Storage & Installation page 4 Pump Maintenance page 5 Wet end Dismantling page 6 Wet end Assembly
More informationIMPORTANT SAFETY INFORMATION:
Owner s Manual Model CUH05B31T IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to install or use this heater. For your safety, always comply with all warnings and safety instructions
More informationMACHINE SHOP ACCESSORIES CLEVER, TIME-SAVING PRODUCTS TO MAKE YOUR LIFE EASIER
MACHINE SHOP ACCESSORIES CLEVER, TIME-SAVING PRODUCTS TO MAKE YOUR LIFE EASIER ROYAL R8 QUICK-CHANGE TOOLING SYSTEM Unit only protrudes 11 8" beyond spindle. 1. Loading the Quick-Change Body into a standard
More informationKC22/32 SERIES Sealless Non-Metallic Centrifugal Pumps Installation and Maintenance Instructions
KC22/32 SERIES Sealless Non-Metallic Centrifugal Pumps Installation and Maintenance Instructions ASSEMBLY Unpack pump from carton and check for shipping damage. WARNING: Magnetic field hazard. This pump
More information