Super Sports Senior- 90

Transcription

1 INSTRUCTION MANUAL Super Sports Senior cubic inch displacement - stroke (glow) Radio required: - channel radio w 5 servos Wing Span Wing Area Flying Length Fuselage Length Specifications in / 050mm 00 sq in / 65. sq dm 9 lbs / 00 g 6 in / 560mm * Specifications are subject to change without notice. * Warning! This model is not a toy. It is designed for precision model. Please seek advice if one familiar this kind of engine powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference. FACTORY PRE-FABRICATED ALMOST-READY-TO-FLY (ARF) SERIES MADE IN CHINA

2 Super Sports Senior - 90 BEFORE YOU BEGIN PARTS LIST ASSEMBLY SAFETY PRECAUTIONS INDEX P. P. P. 3-0 P. 0 BEFORE YOU BEGIN 3 Apply epoxy glue. Apply instant glue (C.A.glue, super glue.) Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. Peel off shaded portion covering film. Cut off shaded portion. 3mm Drill holes with the specified diameter (here: 3mm). Must be purchased separately! Pay close attention here! Pierce the shaded portion covering film. Do not overlook this symbol! P.

3 Parts List. MAIN WING -- pair. SCREW PM X 0mm -- pcs SCREW PM X 5mm -- pcs PUSHER ROD Ø. x 06mm w/ Threads (For Aileron) -- pcs TRI-HORN M3 X mm (L) -- sets CLEVIS -- pcs STRAPER -- pcs FUEL TUBE Ø6 X 5mm -- pcs 3. MAIN LANDING GEAR -- pair MAIN LANDING GEAR COVER -- set MOUNTING PLATE X 0mm -- pcs SCREW PA3 X mm -- pcs SCREW PM X mm -- pcs WASHER d X D5mm -- 6 pcs M NUT -- pcs. SCREW PA3 X mm -- pcs COLLAR Ø5.mm w/ Set screw -- sets MAIN WHEEL Ø90mm -- pcs WHEEL PANTS -- pair MOUNTING PLATE X 0mm -- pcs 5. WING TUBER Ø X 70mm -- pc. 6. STABILIZER & ELEVATOR -- set SCREW PM3 X 5mm -- pc. WASHER d3 X D7mm -- pc. FUSELAGE -- pc. 7. VERTICAL FIN & RUDDER -- set. TAIL LANDING GEAR -- set TAIL WHEEL Ø5mm -- pc. SCREW PA3 X mm -- pcs COLLAR Ø.mm w/ Set screw -- set SCREW PM X mm -- pc. WASHER d X D5mm -- pcs M NUT -- pc. ALUMINUM PLATE 0.3mm -- pc. 9. FUEL TANK 50CC -- set BALSA x 0 x 6mm (For fixing fuel tank) -- pc. 0. ENGINE MOUNT (PL590) -- set SOCKET HEAD SCREW M6 X 30mm -- pcs WASHER d6 X D5mm -- pcs. THROTTLE PUSHWIRE Ø. x 30mm w/plastic tube d x D3 x 5mm -- set ALUMINUM PLATE (For Engine Mount) pc. ANTI - VIBRATION MOUNT -- set INCLUDE: SCREW M X 35mm -- pcs SCREW KM3 X 0mm -- pcs WASHER d X Dmm -- pcs M3 NYLON INSERT LOCK NUT -- pcs M NYLON INSERT LOCK NUT -- pcs. COWLING -- set TRANSPARENT DUMMY COWLING -- set PWA.6 X mm -- 5 pcs SILICON GROMMET d.5 X D6.5mm -- 5 pcs SPINNER Ø70mm -- set 3. WIRE Ø x 900mm (For Rudder) -- pcs COPPER TUBE d.5 X D3. X mm -- pcs RIGGING COUPLER Ø. X 7mm w/ Threads (For Rudder) -- pcs SCREW PM X 6mm -- 3 pcs M NUT -- 3 pcs TRI-HORN M3 X mm (L) (w/ o - Base For Rudder) -- sets FUEL TUBE Ø6 X 5mm -- pcs CLEVIS -- pcs. PUSHROD Ø. x 660mm w/ Threads (For Elevator) -- pcs TRI-HORN M3 X mm (L) -- sets SCREW PM X 6mm -- 6 pcs CLEVIS -- pcs FUEL TUBE Ø6 X 5mm -- pcs 5. LINKAGE CONNECTOR Ø.mm -- set 6. SPONGE 60 X 70 X 5mm -- pc. RIGGING Z BEND Ø. x 7mm (For Rudder) -- pcs PUSHROD Ø. x 70mm (For Elevator) -- pc. COPPER TUBE d.5 X d3. X mm -- pcs STRAPER -- pc. FUEL TUBE Ø6 X 5mm -- pc. PLYWOOD 0 X 35 X 6mm (For Throttle Servo) -- pc. BALSA 6 x 6 x 35 (For Throttle Servo Stand) -- pcs PUSHROD CONNECTOR X 9 X 0mm -- set 7. CANOPY -- set SCREW PWA.3 X mm -- pcs SILICON GROMMET d.5 X 6.5mm -- pcs PILOT PL0005A/B -- pc.. SCREW PM X 35mm -- pcs WASHER d X D5mm -- pcs PLYWOOD x 30 x 0mm (Wing Protection) -- pc. 9. DECALS -- set P. COVERING: RED COLOR SCHEME: TOUGHLON STL 3 BRIGHT RED TOUGHLON STL 30 ORANGE TOUGHLON STL 330 CADMIUM YELLOW TOUGHLON STL 35 DARK BLUE TOUGHLON STL 00 WHITE PURPLE COLOR SCHEME: TOUGHLON STL 35 DARK BLUE TOUGHLON STL 360 VIOLET TOUGHLON STL 36 PURPLE TOUGHLON STL TURQUOISE TOUGHLON STL 00 WHITE

4 Main Wing Pre-glued Aileron Servo PM x 0mm Screw PM x 5mm Screw Pusher Rod. x 06mm Ømm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. Straper PM x 0mm PM x 5mm Fuel Tube 6 x 5mm Bottom View Tri-horn M3 x mm 3 Main Landing Gear PA3 x mm Screw PM x mm Screw d x 5mm Washer 6 M Nut PA3 x mm d x D5mm Washer PM x mm Plate M NUT Bottom View P. 3

5 Main Landing Gear PA 3 x mm Screw 3mm Set Screw 5.mm Collar 3mm Set Screw 5.mm Collar Completed PA 3 x mm Wheel 90mm 5 Main Wing Peel off shaded portion covering film for lead to another aileron servo. Wing Tuber Ø x 70mm Peel off shaded portion covering film Lead to aileron Servo. 6 Stabilizer Elevator d3 x D7mm Washer PM3 x 5mm Screw PM3 x 5mm d3 x D7mm Apply thread locker to screws. Pre-glued Bottom View P.

6 7 Vertical Fin Rudder A A' A = A' Pre-glued Tail Landing Gear PA 3 x mm Screw 3mm Set Screw.mm Wheel Collar PM x mm Screw d x D5mm Washer d x D5mm Washer Washer mm mm M Nut 3mm Set Screw PA3 x mm PM x mm 9 Fuel Tank Fuel Tank 50cc Install Balsa x 0 x 6mm (For fixing fuel tank) Fuel Tank 50cc P. 5

7 0 Engine Mount M6 x 30mm Socket Head Screw d6 x D5mm Washer Engine Mount Pl590 M6 x 30mm d6 x D5mm Apply thread locker to screws. Blind nuts are off-centered to keep the spinner at the fuselage axis. Engine Mx35mm SOCKET HEAD SCREW KM3x0mm Screw M Nylon Insert Lock Nut M3 Nylon Insert Lock Nut d x Dmm Washer Plastic Tube d x D3 x 5mm Throttle Push wire. x 30mm M Nylon Insert Lock Nut d x Dmm Washer KM3 x 0mm d x Dmm Washer Mx35mm SOCKET HEAD SCREW Make sure the rounded edges are facing the shock absorbing SILICON PAD. 3mm Illustration is for inverted mounting. You can mount the engine upright or sideways simply by rotation the engine mount. Thrust angles will not be affected. Install Engine position Spinner 70mm mm 5.6in. P. 6

8 Cowling First insert the grommet to the cowling then apply screw. PWA.6 x mm Screw 5 d.5 x D6.5mm Silicon Grommet 5 Silicon Grommet d.5 x 6.5mm Spinner PWA.6 x mm 3 Rudder Pullwire PM x 6mm Screw 3 M Nut 3 Wire Ø X 900mm Ømm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole marks at side of control surfaces. 35mm M Nut Tri-horn PM x 6mm Elevator Pushrod PM X 6mm Screw 6 Ømm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. PM X 6mm Pushrod Ø. X 660mm w/threads 35mm Clevis Fuel Tube P. 7

9 5 Servo Set LINKAGE CONNECTOR 3mm 3 x 3mm Set Screw Linkage Connector Throttle Rod Included with the Radio Set. mm Nut mm mm Washer mm Throttle Servo. Please refer to attached sheet for linkage connector installation. 6 Radio Equipment Install and arrange the servo as shown in the diagram. Copper Tube Press down the center /3 portion Front Balsa 6 x 6 x 35mm Spong 60 X 70 X 5mm Rudder Servo Wire Ø X 900mm Throttle Servo Plywood 35 x 6 x 0mm Fuel Tube Straper Copper Tube Pushrod Connector X 9 X 0mm Rigging Z Bend Ø. x 7mm Balsa 6 x 6 x 35mm Elevator Servo Pushrod. X 70mm Bottom View Elevator Servo M Nut Elevator Pushrod Ø.x70mm Bottom View KM xmm P.

10 7 Canopy First insert the grommet to the canopy then apply screw. PWA.3 x mm Screw d.5 x D6.5mm Silicon Grommet Pilot Silicon Grommet d.5 x 6.5mm PWA.3 x mm Main Wing PM x 35mm Screw d x D5 Washer PM x 35mm d x D5mm mm Bottom View 9 Wing Setting Adjust the wing and fuselage configuration as in the diagrams B B' A A' C C' A = A' B = B' C = C' P. 9

11 0 Control Throws Elevator 0mm 0mm Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference. Rudder mm mm Aileron 9mm 9mm C.G The ideal C.G. Position is 0mm (.5 in) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying. 0mm Important Safety Precautions First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary. Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft. Super Sports Senior - 90 is specially designed to be powered by 0.9 stroke glow engine, using a more powerful engine does not mean better performance. In fact, over powered engine may cause severe damage and injuries. Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running propeller. If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles. Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone. Too hot an iron may damage the covering. Check and re-tighten up all factory assembled screws, use thread locker if applicable. A9R060 P. 0

12 The World Models Manufacturing Co., LTD. www. theworldmodels. com A9R060