Rotary Control Panel (49200-RHA)

Transcription

1 an ISO 900:008 Registered ompany Rotary ontrol Panel (900-RA) OFF O ED I 8865 Goll St. San Antonio, TX 7866 Phone: Fax: RA REV D /5/6, PG OF 8

2 Table of ontents over... Table of ontents... Packing ist/parts Disclaimer... ontrol Panel Installation... Operation of ontrols... 5 Gen II ompac & Super Wiring Diagram... 6 Gen II ini Wiring Diagram... 7 Packing ist RA REV D /5/6, PG OF 8

3 No Qty. Part No. 09-VUT -RUA 58-VUS 857-VU 0558-VUP 0570-VUP 057-VUP 057-VUP 900-RI 99-VUI 957-VUI -VUW 9-VUW Packing ist: Rotary ontrol Panel (900-RA) Description Rotary, 8 Adjustable Potentiometer, Rotary Rotary, -Speed Shaft Nut, 7/6, Speed, ode,, eat ezel, Slimline Knob, Rotary Potentiometer Knob, ontrol uddy lip Jumper Wire, 6 Flat Washer, Potentiometer Shaft Nut, Potentiometer ** efore beginning installation, open all packages and check contents of shipment. Please report any shortages directly to Vintage Air within 5 days. After 5 days, Vintage Air will not be responsible for missing or damaged items. NOTE: The heater control valve knob is retained by a 5/6 Allen screw NOTE: Images may not depict actual parts and quantities. Refer to packing list for actual parts and quantities RA REV D /5/6, PG OF 8

4 ontrol Panel Installation Select a suitable location for the control panel. NOTE: When choosing a suitable location, consider the heater control valve location, wiring harness length and the distance from the capillary tube to the evaporator unit. The panel may be mounted under the dash, or switches can be removed and installed directly in the dash.. Using 9% isopropyl rubbing alcohol and a shop towel, wipe down the dash surface or the bezel to remove any dust, debris or residual oil, and to ensure proper label adhesion. NOTE: Failure to clean and prepare the dash or bezel surface may result in poor label adhesion.. Apply the labels onto the dash or bezel surface in the following order from left to right:, ode, eat and.. Uncoil the capillary tube from the thermostat, and insert the capillary tube into the evaporator coil to a depth of ½. NOTE: The hole for the capillary tube is located under the blue sticker on top of the evaporator unit. 5. Wire the system as shown on Page 6 for Gen II ompac and Super units, or Page 7 for Gen II ini units. eat ode Shop Towel Plastic ezel Wipe Down Surface of Dash or ezel with Alcohol ode eat Rotary Potentiometer Rotary Potentiometer Plug ust be onnected to Electronic odule arness ode Rotary ontrol Panel (Rear View) NOTE: efore operating system, carefully uncoil capillary tube and insert it into predrilled hole on top of evaporator case (blue dot) to a depth of ½. apillary Tube RA REV D /5/6, PG OF 8

5 Operation of ontrols OFF O ED I i-evel Floor Dash Defrost ot Off old Off Speed ode eat A/. Any vent temperature is available in any mode.. Select desired mode, then adjust air temperature for comfort.. eat knob adjusts flow of hot water through the heater. ounterclockwise is off. lockwise is for increasing heat.. A/ thermostat knob controls the evaporator coil temperature. ounterclockwise is off. Full clockwise is maximum cold (8 ). 5. For A/ operation, rotate thermostat clockwise to its stop, then back off slightly (/8 turn) to prevent coil freeze-up. To warm up vent temperature during A/ operation, slightly increase the heat knob setting. 6. For heat operation, rotate thermostat counterclockwise to its stop (off), then adjust heat knob for desired temperature. 7. For defrost operation, adjust A/ thermostat to / cold, then adjust heat knob to attain proper temperature for de-fog/defrost RA REV D /5/6, PG 5 OF 8

6 Wiring Diagram: Gen II ompac/super Units eat/ool/defrost (Required) ompressor Safety (inary Type) A/ lutch A/ lack ode Speed Pink Green Power Relay 87 87a (Optional) For Defrost Only! / / Grey/lack / / Grey/lack 87 87a igh Relay eater ontrol Valve Potentiometer Aux. otor onnect to Key-on Ignition Source (5-Amp Fuse) 0-Amp ircuit reaker at. ontrol odule To attery or attery Terminal on Starter Solenoid. lack rown t. Floor/Vent Servo Grey (Optional) For Defrost Defrost Only! Servo Note Orientation of Plugs lack/ / / /rown / eater ontol Valve Servo RA REV D /5/6, PG 6 OF 8

7 Wiring Diagram: Gen II ini Units eat/ool/defrost (Required) ompressor Safety (inary Type) A/ lutch A/ lack ode Speed Pink Green Power Relay 87 87a (Optional) For Defrost Only! / / Grey/lack / / Grey/lack 87 87a igh Relay eater ontrol Valve Potentiometer lack Spal Type otor Aux. Resister On onnect to Key-on Ignition Source (5-Amp Fuse) 0-Amp ircuit reaker at. To attery or attery Terminal on Starter Solenoid. ontrol odule rown lack t. Floor/Vent Servo Grey (Optional) For Defrost Defrost Only! Servo (Rear View of Plug) Note Orientation of Plugs lack/ / / /rown / eater ontol Valve Servo RA REV D /5/6, PG 7 OF 8

8 No Qty. Part No. 09-VUT -RUA 58-VUS 857-VU 0558-VUP 0570-VUP 057-VUP 057-VUP 900-RI 99-VUI 957-VUI -VUW 9-VUW Packing ist: Rotary ontrol Panel (900-RA) Description Rotary, 8 Adjustable Potentiometer, Rotary Rotary, -Speed Shaft Nut, 7/6, Speed, ode,, eat ezel, Slimline Knob, Rotary Potentiometer Knob, ontrol uddy lip Jumper Wire, 6 Flat Washer, Potentiometer Shaft Nut, Potentiometer hecked y: Packed y: Date: NOTE: The heater control valve knob is retained by a 5/6 Allen screw NOTE: Images may not depict actual parts and quantities. Refer to packing list for actual parts and quantities RA REV D /5/6, PG 8 OF 8