Series 650 Read ALL INSTRUCTIONS carefully.

Transcription

1 Save This Manual For Future Reference Installation and Service Manual Air Cleaners Series 650 Read ALL INSTRUCTIONS carefully. Eramco PO Box 519 Royse City, TX Part No Rev. 1C This manual is copyright protected by ERAMCO. Any reproduction of this manual, in part or full, without the written permission of ERAMCO, constitutes a violation of the U.S. copyright laws and is subject to prosecution. Printed in the U.S. by the Graphics Productions Department of ERAMCO, 1998.

2 PERFORMANCE OVERVIEW 2 The Series 650 is a fully self-contained, high efficiency air purifier. It has a filter combination to handle the toughest particulate and odor problems. The Series 650 consists of a 2" pleated prefilter, the high capacity, 98% DOP HEPA-type filter, and the activated charcoal final filter. An optional ozone generator is available for superior odor control. The Series 650 can be ducted for above ceiling installations and has a silencer accessory to reduce its sound level. The unit is ideal for controlling tobacco smoke and odors as well as air borne bacteria, virus, pollens and dust. The 4 way discharge air louver can be adjusted to direct the sterile air into all corners of the space. SPECIFICATIONS Series 650 Specifications Dimensions: 32"L x 25"W x 14"H (81.3 x 63.5 x 35.6 cm) Weight: 67 lbs. (30.4 kg) Installed 94 lbs. (42.6 kg) Shipping Motor: 1/3 HP, 115v, 60 Hz, 1 PH, 4 Amps, thermally protected. Optional 208/230v motor available. Electrical: 8' grounded power cord and 2-speed toggle switch. Performance: Up to 1000 CFM (28.3 CMM) depending on filter configuration. One unit required for each 800 to 1600 sq. ft. of space, assuming 8 ft. ceiling heights, depending on pollution source. (35.6cm) 14" 25" (63.5cm) 32" (81.3cm)! Foreign objects should be kept clear of the unit's blower. Disconnect electrical power before performing maintenance on the motor.

3 UNIT LOCATION 3 The Dust Free air cleaners should be suspended from the ceiling at a height of 15ft or less above the floor. Position units as shown in the following illustrations. If you need additional installation advise contact the distributor/dealer from whom you purchased the equipment. Call the factory if the distributor/dealer is not available. Single-Unit Configuration Top view of room Place unit no less than 12 feet from wall. 70% of room length but not more than 45 feet. Dual-Unit Configuration Top view of room Place unit no less than 12 feet from wall. Place unit no less than 12 feet from wall. Multi-Unit Configuration Top view of room No less than 25% of room length. 30% of room length. No less than 25% of room length.

4 MOUNTING 4 HANGING The unit requires a minimum of four (4) points of support. The mounts should be positioned at each of the four corners. Be sure to leave sufficient room to access and maintain the motors and filters. Use chain or cable of sufficient strength and hang the unit 15 feet or less above the floor. To hang unit from the ceiling screw 3/8" eye bolts into the threaded inserts located at the top corners of the unit. Use cable or chain to suspend the unit.! Take note of the units weight and the maximum safe static load that the mounting location will support. The blower end of the unit will be heavier than the filter end.

5 MAINTENANCE 5 FILTERS Your Series 650 comes equipped with disposable filters which must be replaced at regular intervals. They cannot be cleaned. The length of time between filter replacement is dependent on the amount of contamination in the environment. Generally, the pre-filter will last 1 to 3 months while the main filter will last 6 to 12 months. Replace the filters when there is a noticeable drop in air volume. The filters must be replaced with filters of the same, size, type, and efficiency rating in order to maintain the performance of the unit. Incorrect filters can lead to premature motor failure and will void the manufacturer's warranty. Check the distributor or manufacturer to determine the exact filter configuration for the specific installation. The filters are serviced by following these steps: Note: If your unit is equipped with an ozone generator, the generator should be removed and the screen grids should be cleaned in soapy water, rinsed and dried each time the primary filters are replaced. 1. Open the filter access door. 2. Slide the dirty filters out. 3. Insert new filters. 4. Close filter access door. Filter Change Diagram The Series 650 can be fitted with an intake and/or a discharge air plenum for ducting. The ducting should be 16" in diameter or more, or the equivalent in square or rectangular ducts. The duct runs should not exceed 35 ft. total. The Series 650 air volume will be reduced by up to 20% when plenums and ducting are attached.

6 REPLACEMENT PARTS LIST 6 Part No Description Disposable 2" Pleated Pre-Filter (6 Filters Per Box) Washable Electrostatic Pre-Filter (One Filter Per Box) 95% ASHRAE Primary Filter (One Filter Per Box) 98% D.O.P. Primary Filter 5/8" Disposable Charcoal Panel (Empty) 2" Refillable Charcoal Panel Variable Speed Switch 1/3 HP, 120V Blower Motor (No Blower) ON/OFF 2 Speed Switch Motor Capacitor Carbon (30 Lb. Box) Permanganate (HS-600) (40 Lb.Pail) Series 650 Filter Layout (Shown With Door Removed) Optional Ozone Generator Junction Box (For Wiring) Pre-Filter Primary Filter Charcoal Filter Service Door Latches Motor/Blower Assembly