C&M REAR FEED Long-stroke Vertical Down-stroke Baler for Baling Multi-Materials

Size: px

Start display at page:

Download "C&M REAR FEED Long-stroke Vertical Down-stroke Baler for Baling Multi-Materials"

Alvin Chapman
5 years ago
Views:

June 21, 2011 Used C&M 3050V-7-15 C&M REAR FEED Long-stroke Vertical Down-stroke Baler for Baling Multi-Materials MATERIAL TO BE BALED: Used Clothing & Other Materials BALER DESCRIPTION: USED C&M

1 June 21, 2011 Used C&M 3050V-7-15 C&M REAR FEED Long-stroke Vertical Down-stroke Baler for Baling Multi-Materials MATERIAL TO BE BALED: Used Clothing & Other Materials BALER DESCRIPTION: USED C&M MODEL 3050V-7-15 Serial Number 11608VS Multi-Material Vertical single ram manual tie down-stroke single box baling press for bales 50 wide x 30 deep x high with: Bales weight depends on material & bale height. 1. Heavy-duty structural steel baler frame 15-6 high with top frame mounted hydraulic power unit rated for 3000 PSI components including 15 HP TEFC 230/460 Volt, 3 PH, 60Hz motor with hydraulic pump, directional valve, pressure relief valve, and hydraulic reservoir 2. 7 bore x 68 stroke with 4 rod industrial grade compression cylinder pin attached to compression platen with replaceable UHMW ram wear guides to cycle in approximately 60-seconds 3. PLC controlled operation & independent operators panel 4. Safety gate interlocked for front loading over bale door 5. Semi-automatic or manual operation 6. Manual turnbuckle door latch/unlatch bale door & lock 7. Hydraulic open/close rear feed chute for cart dumper 8. Hydraulic up/down bale eject 9. Automatic compression cycles 10. Front feed always optional 11. Special designed ram slots and baler floor slots for four or six steel wire ties or polyester strap bale ties 12. Audible completed bale horn and strobe light 13. Over 100,000 pounds of compression force at 2,700 PSI with 71.5 pounds of force per-square inch of ram face surface. 14. FOB C&M factory Winston-Salem, NC TOTAL PRICE: Used C&M Model 3050V-7-15 (1) through (15)... USD 19,500

C&M Used Specialized Vertical CM3050V-7-15 Page 2 REAR LOADING

Twin Post double fork high-lift cart dumper modified for dumping

unit and controls modified for use with C&M designed Hydraulic

.. USD 8,750 TOTER DUMP CARTS Special molded Dump Cart, 0.

0"h overall, Load Rating: 1100 lbs/499.0 kg, Low side is 34.

2 C&M Used Specialized Vertical CM3050V-7-15 Page 2 REAR LOADING for CM3050V-7-15 Note: This style rear infeed chute is required for use with cart dumpers. CART LIFTER for rear loading baler model CM2754V-15-7: Used Toter Twin Post double fork high-lift cart dumper modified for dumping carts up to 120 above floor including independent hydraulic power unit and controls modified for use with C&M designed Hydraulic Rear Loading Chute... USD 8,750 TOTER DUMP CARTS Special molded Dump Cart, 0.9 cubic yard or 24.3 cubic feet, 55.0"l x 35.5"w x 42.0"h overall, Load Rating: 1100 lbs/499.0 kg, Low side is 34.0 H, Ship Wt. /Unit: 120 lbs/54.4kg, Casters: 6"-2 Directional Lock, 2 Swivel; Corner Placement, Color: Gray - 20 Carts... USD 3,200 Total for CM3050V Baling System... USD 31,450

3 C&M Used Specialized Vertical CM3050V-7-15 Page 3 FREIGHT: START-UP: TERMS: F.O.B. Winston-Salem, NC Start-up and training for operating and maintenance personnel by C&M Baling Systems' factory field service engineer for two (2) days including travel USD per day plus travel expenses portal to portal [10 day advance notice required] Thirty percent (30%) initial payment is required with receipt of purchase order with terms for progress payments as follows: thirty percent (30%) 30-days prior to shipment, thirty percent (30%) at time of shipment, and balance of ten percent (10%), plus all applicable taxes and any other related charges payable net ten-days after installation (not to exceed 45- days from shipment) WARRANTY: C&M Used Baler Limited Warranty Policy dated January 1, 1997 Baler end-user to furnish: Layout (footprint) drawing approval Modified electrical drawings, acceptable to C&M, if altered after C&M layout is approved Unloading and secured placement of baler to proper location, ISO Grade 46 (or equal) hydraulic oil filled to proper level in baler hydraulic reservoir, and electrical connections to baler power box (460 volt three-phase electrical connection to electrical enclosure) Labor, as needed, to assist C&M factory field service engineer during installation checkout and baler startup Facility maintenance personnel (at least one person) and baler operator or supervisor for hands-on training during baler startup process for at least two full days each during the three day installation checkout and baler startup period A pre-planned baler operation & baler safety training meeting to including senior baler operation and maintenance employees for at least two uninterrupted hours on final day of baler commissioning/start-up

4 LIMITED WARRANTY POLICY January 1, 1997 Page 1 of 2 USED BALER MANUFACTURER'S WARRANTY C&M Baling Systems, Inc. warranty on the used CM3050V-7-15 with used Toter Dumping System to be free of defects in material and workmanship under normal use and service for a period of ninety (90) days, based on an eight-hour day, five days per week operation. This warranty applies to the original purchaser only and the manufacturer's obligation under this warranty is limited to ninety (90) days for repair or replacement of parts to manufacturer's mechanical and hydraulic equipment. Electrical components are not warranteed. Manufacturer's warranty or obligation in connection with the sale of this equipment: 1. Warranty on all purchased parts will carry the same warranty as extended to C&M by its suppliers. All parts shipped against a warranty claim will be invoiced when shipped and will be credited only when the original manufacturer has returned the part for inspection and approval for claim. The obligation of C&M is expressly limited to repair or replacement as approved by the original manufacturer. 2. Warranty on manufacturer defects or workmanship shall be limited to a lack of items necessary for completeness or an imperfection in materials fabricated and assembled by C&M Baling Systems, Inc. 3. All repair or service work must be approved by C&M and must be performed by manufacturer, distributor, or approved service organization and factory approved parts must be used for repair or replacement of original factory supplied equipment. The use of unapproved parts or service personnel will void manufacturer's warranty. 4. Warranty shall not apply to any failure or damage incurred through neglect, lack of maintenance, misuse, accident, fire, vandalism, improper installation, redesigning of assemblies, or through any other cause beyond the control of the manufacturer. This includes any failure or damage incurred through improper electrical feed to the system or any of its components. 5. Warranty shall not apply if the equipment has been operated beyond the factory recommended maximum capacity. 6. In no event shall C&M be held responsible for incidental or consequential damages. 7. Warranty shall not cover labor by the customer or outside contractor to install components and shall not cover any charges for lost production. 8. Warranty shall not cover shipping and special handling charges to expedite parts.

5 C&M WARRANTY POLICY January 1, 1997 Page 2 of 2 9. Cleanliness must constantly be enforced during and after the installation to maintain the maximum efficiency of the hydraulic system. When routine maintenance of the equipment is neglected or when proper cleanliness procedures are not followed, as per the manual, the manufacturer's warranty shall be void. 10. No claim under this warranty shall be valid unless such claim is submitted within twelve (12) months after the date of sale for all parts or service labor. It has been the continuous policy of C&M to ensure complete customer satisfaction. This is your assurance that you can expect prompt, efficient service on your equipment from C&M and the C&M distributor/dealer organization. NOTICE: Certain parts used on C&M balers are only under warranty by the manufacturer for repair, NOT replacement. Electronic and electrical parts are not covered under this warranty after initial startup. C&M balers are factory assembled, tested, and cycled to assure quality and condition of electrical and hydraulic components. C&M accepts no responsibility for damage to electrical components caused by improper electrical connections, wrong voltages, low voltage, or voltage surges.

TC-720 RECYCLING BALER

OPERATING AND MAINTENANCE INSTRUCTIONS TC-720 RECYCLING BALER READ INSTRUCTIONS THOROUGHLY BEFORE OPERATING Sept. 06, 2013 3451 S. 40th Street Phoenix, AZ 85040 602.437.5020 800.223.4540 www.tsissg.com