Optima i.q. EAF-100 *

Transcription

1 Optima i.q. EF-0 * EF-0 EF-0-ISM-DPU-I PRTS LIST EF-0 FUETS Item No. ode No. Part No. Description EF gpm (5.7 Lpm) erator Spray Head EF- 2.2 gpm (8.3 Lpm) erator Spray Head EF gpm (1.9 Lpm) Spray Head EF gpm (1.3 Lpm) Spray Head (Multi-Lam) EF-6- Throat Plate ssembly (Plug-in dapter Models) EF-7- Throat Plate ssembly with i.q.-cliq (Plug-in dapter Model) EF V/6.75 VD Plug-In dapter (US) EF-1 Faucet Mounting Kit EF-9 Strainer (Filter) EF-01 Mixer Handle ssembly and artridge EF-02 Handle Repair Kit EF (330 mm) Flexible Supply Hose ETF-607- Trim Plate 4 enter-set Sink ETF-608- Trim Plate 8 enter-set Sink EF-2 Solenoid EF /16 (300 mm) Extension able EF /4 (1200 mm) Extension able EF (3200 mm) Extension able 12. EF-44- Power Splitter EF-37 6 VD ox Mount dapter EF V/6.75 VD Plug-In dapter (EURO) EF V/6.75 VD Plug-In dapter (UK) EF-44 replaces separate EF-23- Splitter able and EF-28 apacitor, which is sold separately. Electrical onnection up to Six (6) Faucets Using One (1) dapter (3) 6 VD PLUG-IN DPTER (12) POWER SPLITTER (12) POWER SPLITTER (12) POWER SPLITTER TO DDITIONL FUETS (6 MX.) * EF-0 faucets introduced in 2011 now require EF-28- apacitor or EF-44- Power Splitter in ganging applications. 144

2 Optima i.q. EF-0 UTO RNGE DJUSTMENT OPERTION button one (1) time, n immediately step away. Faucet will run four (4) seconds and range will automatically adjust to its environment. Wait ten () seconds after water shuts off bee using faucet. If faucet does not function, refer to Troubleshooting section of this instruction manual. Prepare. button once.. Remove sticker.. Water will flow 4 seconds MNUL RNGE DJUSTMENT Note: Use Manual range adjustment only when desired range cannot be obtained with auto range adjustment shown above. D. Wait seconds, n faucet is ready. 4 Push button two (2) times (double click). Push again five (5) seconds until LED flashes four (4) times. Then release button and wait five (5) seconds. If waterflow doesn t start after removing sticker and red led within sensor flashes continue with following procedure!!. button once. Push and hold button in as Faucet continuously cycles through following five (5) range settings. One (1) flash = shortest range Two (2) flashes = short range Three (3) flashes = medium range Four (4) flashes = long range Five (5) flashes = longest range Release button at desired setting. Then water will flow four (4) seconds signaling confirmation of setting. Wait an additional ten () seconds bee using Faucet. Note: Updated electronics have visible red and green LED. Original electronics have only red LED aadn range setting is reversed (1=longest, 8=shortest) 5x 4x 3x 2x. Hold a white sheet of paper 1.5 (40 mm) in front of sensor until water flows 4 seconds. Remove paper. D. Wait seconds, n faucet is ready

3 Optima i.q. EF-0 TROULESHOOTING GUIDE 1. Faucet does not function.. dhesive packaging label affixed over sensor eye. Remove adhesive label from sensor eye.. Permanent Off activated. button on faucet throat one time. 2. Faucet delivers water in an uncontrolled manner. 3. Faucet does not deliver any water when sensor is activated. INDITOR: Solenoid valve produces an audible LIK.. Water supply stop(s) closed. Open water supply stop(s).. Water supply stop strainer(s) clogged. lean water supply stop strainer(s). INDITOR: Solenoid valve DOES NOT produce an audible LIK.. Power failure (EF-0 Models). heck power supply. 4. Faucet delivers only a slow flow or dribble when sensor is activated.. Water supply stop(s) are partially closed. ompletely open water supply stop(s).. Water supply stop strainer(s) clogged. Remove, clean, and reinstall water supply stop strainer(s). Replace strainer(s) if required.. erator is clogged. Remove, clean, and reinstall aerator. Replace aerator if required. D. Faucet is not working properly. 5. Faucet does not stop delivering water or continues to drip after r is no longer detected. 6. i.q.-cliq doesn t function (-I models only). utton is not working properly. 7. The water temperature is too hot or too cold on a faucet connected to hot and cold supply lines.. Supply stops are not adjusted properly. djust supply stops.. For models with integral mixing valve mixing valve is set improperly water temperature desired. Rotate mixing valve handle clockwise to decrease water temperature or counterclockwise to increase water temperature. RE ND LENING OF HROME ND SPEIL FINISHES DO NOT abrasive or chemical cleaners (including chlorine bleach) to clean faucets that may dull luster and attack chrome or special decorative finishes. Use ONLY mild soap and water, n wipe dry with clean cloth or towel. While cleaning bathroom tile, protect faucet from any splattering of cleaner. cids and cleaning fluids will discolor or remove chrome plating. When assistance is required, please contact Sloan Technical Support at: SLON-14 ( ). 146

4 Optima i.q. EF-150 EF-150 EF-150-ISM-DPU-I PRTS LIST EF-150 FUETS Item No. ode No. Part No. Description EF- 2.2 gpm (8.3 Lpm) erator Spray Head EF gpm (1.9 Lpm) Spray Head EF gpm (1.3 Lpm) Spray Head (Multi-Lam) EF-3- Throat Plate ssembly (attery Models) EF-4- Throat Plate ssembly with i.q.-cliq (attery Model) EF-00 attery Replacement Kit EF-1 Faucet Mounting Kit EF-9 Strainer (Filter) EF-01 Mixer Handle ssembly and artridge EF-02 Handle Repair Kit EF (330 mm) Flexible Supply Hose ETF-607- Trim Plate 4 enter-set Sink ETF-608- Trim Plate 8 enter-set Sink EF-2 Solenoid

5 Optima i.q. EF-150 UTO RNGE DJUSTMENT button one (1) time, n immediately step away. Faucet will run four (4) seconds and range will automatically adjust to its environment. Wait ten () seconds after water shuts off bee using faucet. If faucet does not function, refer to Troubleshooting section of this instruction manual. TTERY REPLEMENT Replace battery when red LED indicator flashes each time faucet is in or when faucet stops functioning. Step 1 lose supply stop(s). MNUL RNGE DJUSTMENT Note: Use Manual range adjustment only when desired range cannot be obtained with auto range adjustment shown above. Step 2 Loosen screw with hex wrench. Remove throat plate. Disconnect electrical lead at connector if required. Push button two (2) times (double click). Step 3 Remove battery cover using a No. 1 Phillips head screwdriver. Remove old battery. Dispose of properly. Push again five (5) seconds until LED flashes four (4) times. Then release button and wait five (5) seconds. Step 4 Wait three (3) minutes bee inserting new battery. Push and hold button in as faucet continuously cycles through following five (5) range settings. One (1) flash = shortest range Two (2) flashes = short range Three (3) flashes = medium range Four (4) flashes = long range Five (5) flashes = longest range Release button at desired setting. Then water will flow four (4) seconds signaling confirmation of setting. Wait an additional ten () seconds bee using faucet. Note: Updated electronics have visible red and green LED. Original electronics have only red LED and range setting is reversed (1 = longest, 8 = shortest) 5x 4x 3x 2x Step 5 Insert a new 6 volt type R-P2 lithium battery. The red LED will flash one (1) minute. Reinstall battery cover. Reconnect electrical lead at connector if previously disconnected. Reinstall throat plate. If LED doesn't flash or if it just lights up, remove battery. Wait three (3) minutes, n reinsert battery. If water flows continuously after inserting new battery and opening supply stops, remove battery. Wait three (3) minutes, n reinsert battery. Step 6 Open supply stops. 171

6 Optima i.q. EF-150 TROULESHOOTING GUIDE OPERTION Prepare. button once. 1. Faucet does not function.. dhesive packaging label affixed over sensor eye. Remove adhesive label from sensor eye.. Permanent Off activated. button on faucet throat one time. 2. Faucet delivers water in an uncontrolled manner. 3. Faucet does not deliver any water when sensor is activated. INDITOR: Solenoid valve produces an audible LIK.. Water supply stop(s) closed. Open water supply stop(s).. Water supply stop strainer(s) clogged. lean water supply stop strainer(s). INDITOR: Solenoid valve DOES NOT produce an audible LIK.. attery low (EF-150 Models). Replace battery (refer to battery replacement). 4. Faucet delivers only a slow flow or dribble when sensor is activated.. Water supply stop(s) are partially closed. ompletely open water supply stop(s).. Water supply stop strainer(s) clogged. Remove, clean, and reinstall water supply stop strainer(s). Replace strainer(s) if required.. erator is clogged. Remove, clean, and reinstall aerator. Replace aerator if required. D. Faucet is not working properly. 5. Faucet does not stop delivering water or continues to drip after r is no longer detected. 6. i.q.-cliq doesn t function (-I models only). utton is not working properly. 7. The water temperature is too hot or too cold on a faucet connected to hot and cold supply lines.. Supply stops are not adjusted properly. djust supply stops.. For models with integral mixing valve mixing valve is set improperly water temperature desired. Rotate mixing valve handle clockwise to decrease water temperature or counterclockwise to increase water temperature. RE ND LENING OF HROME ND SPEIL FINISHES DO NOT abrasive or chemical cleaners (including chlorine bleach) to clean faucets that may dull luster and attack chrome or special decorative finishes. Use ONLY mild soap and water, n wipe dry with clean cloth or towel. While cleaning bathroom tile, protect faucet from any splattering of cleaner. cids and cleaning fluids will discolor or remove chrome plating.. Remove sticker.. Water will flow 4 seconds 4 D. Wait seconds, n faucet is ready. If waterflow doesn t start after removing sticker and red led within sensor flashes continue with following procedure!!. button once.. Hold a white sheet of paper 1.5 (40 mm) in front of sensor until water flows 4 seconds. Remove paper. D. Wait seconds, n faucet is ready. 4 When assistance is required, please contact Sloan Technical Support at: SLON-14 ( ). 172

7 Rev. 1 (08/11) Preparing EF-150 DDENDUM Inbetriebnahme PREPRE FOR OPERTION Inbetriebnahme Inbetriebnahme Inbetriebnahme Preparing Preparing Preparing 4 entfernen... button once. entfernen... entfernen... entfernen Remove sticker. D Wait seconds, n Water will flow 4 seconds. faucet is ready. - ready mit IF WTERFLOW DOESN T STRT FTER REMOVING THE STIKER mit mit mit ND THE RED LED WITHIN THE SENSOR FLSHES ONTINUE WITH THE FOLLOWING PROEDURE!! Inbetriebnahme Inbetriebnahme Preparing Preparing 44 4 button once. entfernen... lattentfernen... ca. vor bis... halten once...hold white paper app. in front of sensor until... Hold a white sheet of paper 1.5 (40 mm) in front of sensor until water flows 4 seconds D Wait seconds, n faucet is ready. Remove paper. is necessary, please contact your once...hold once...hold once...hold white white white paper paper paper app. app. app. local Sloan Rep or Sloan Tech in front in in front front of of sensor of sensor sensor until... until... until... Support at: SLON-14 mitmit ( ). latt latt latt ca.ca. ca. vorvor vor halten halten halten bis... bis... bis... When furr assistance SLON OMPNY 500 SEYMOUR VENUE FRNKLIN PRK, IL Phone: VLVE-9 ( ) or Fax: or OPYRIGHT 2011 SLON OMPNY Rev. 1 (08/11)