SERVICE MANUAL. WHITE KNIGHT CL43 Reversing Integrated Dryer - UK Technical Data Exploded Views Wiring Diagram Parts List

Transcription

1 SERVICE MANUAL WHITE KNIGHT CL43 Reversing Integrated ryer UK Technical ata Exploded Views Wiring iagram Parts List January

2 Service & Repair Information Tumble ryer White Knight CL432 uiltin ryer UK I Technical ata General Frontloading standard door opening builtin tumble dryer model. Forward and reverse tumble. Single or double element heating. Timer control. Induced airflow passes through rear ventilation inlets, over heating element, through drum rear perforations, through laundry load/lint filter, through fan and into the exhaust venting. oor opening direction optional left to right or right to left. Identity Model type, manufacturer source, date and serial number are displayed on a white label revealed when the door is open, below where the filter is located. HA identifies the machines as having been manufactured at the Halifax factory. The 1st & 2nd numerals represent the year of manufacture (e.g is represented by 04) The 3rd & 4th numerals represent the month of manufacture (e.g. March is represented by 03). The final 6 numerals represent the main serial number of the machine. All information from this label should be quoted in any service communication. Mains Voltage 220/240V 50HZ Maximum Power Consumption 2450W Approximately Connections Please note; plug not fitted to builtin machines. They are designed to be connected to a double pole switched spur with at least 3mm contact separation with a pilot lamp. The appliance must be earthed imensions Height 87cm (33.9 ) to 89cm (34.7 ) depending on the adjustable feet. Width 59.6cm (23¼ ) epth 53cm (21 ) epth when rear vent hose is assembled 60cm (⅝ ) Weight With packing 32.5kg approximately Without packing 31kg approximately Air Flow 140m³/h with capacity laundry load Grant Hood 2004 Page 1 04/03/2004

3 II Components rive Motor Permanent split capacitor induction 4 polereversing ⅛HP with heat and current sensitive overload protection. Trip temperature between 125 C and 155 C. Reset 90 C. Winding resistances 41.08Ω and 43.3Ω. 8µF Capacitor. No Load Full Load Power Consumption 110W approximately 225W approximately Current Consumption 0.45A approximately 0.75A approximately Speed 1450 RPM approximately 1350 RPM approximately Heater Power Consumption (determined by programme) Low Setting 1125W High Setting 2250W Temperature Overload Cutout (TOC) (bimetal contacts normally closed) Contacts open 120 C under No Air Flow condition Contacts reset manual operation Inlet (Heater) Thermostat (bimetal contacts normally closed) Contacts open 142 C under restricted air flow conditions Contacts reset 115 C automatically Exhaust Thermostat (bimetal contacts normally closed) Contacts open 60 C under normal air flow conditions Contacts reset 49 C automatically Timer Composite programme timer. Variable time setting up to 128mins plus 12 minutes cooldown Clockwise 5 minutes 46 seconds (heater on except for first and last 2 seconds) Pause 2 seconds (heater off) Anticlockwise 10 seconds (heater off) Pause 2 seconds (heater off) rum rum Wrapper, Front and Rear are manufactured from Galvanized Steel Volume: 105 litres Capacity: 6kg dry cotton Speed: 5059 RPM approximately Rotation: alternating clockwise 5 minutes 46 seconds and anticlockwise 10 seconds Grant Hood 2004 Page 2 04/03/2004

4 III General Information To assist with part identification, a key number is stated in parentheses after a specific part is mentioned so that it can be located on the Parts List for this appliance and consequently on the Exploded Views. asic Programme After loading damp clothes into the dryer, the door must be closed or the programme cannot begin. Clockwise rotation of the Control Knob (352) closes switch contacts within the Timer (211) to (a) energise the main motor (101) and (b) energise the heater (227). The Timer switch contacts will remain closed until the Timer motor mechanism returns the Control Knob to the 0 position. The contacts controlling heating will open 12 minutes before the Timer Knob reaches the 0 position. This is to allow the circulation of cool air for prevention of creasing to synthetic garments. The Heat Selector Switch (216) provides options for either 1.125kW or 2.25kW heating. Thermal Controls Temperature Sensitive Control Switches are electrically in series with the Heater (227). In most conditions, only the Exhaust Thermostat (229) will operate to control the drying programme (automatic reset). An additional Manual Reset TOC (Thermal Overload Control) (228) will operate when severely restricted or lost airflow conditions exist; i.e. air vents blocked, no motor action, belt has come off etc. This switch can be identified by its red coloured reset button protruding from the ack Panel (413). Grant Hood 2004 Page 3 04/03/2004

5 IV Adjustments and Recommendations for ismantling To assist with part identification, a key number is stated in parentheses after a specific part is mentioned so that it can be located on the Parts List for this appliance and consequently on the Exploded Views. efore working on the appliance, the external cupboard door must be removed and the dryer pulled out from its recess within the cupboard. Front Access Access to all Control Switches is available after removal of the Top Cover (386). For the removal of the Front Panel (376), oor Microswitch (248), earing Housing (440), Seal (442) and earings (445), the machine should be laid flat on its rear after the Top Cover (386), Top Cover rackets (385) and Plinth (199) have been removed. Withdraw the securing screws from the top of the Control Panel (353) together with all of the screws and fittings in connection with the Front Panel (376) and the oor Assembly (203). The Front Panel can then be detached from location lugs with the Control Panel (353) and Cabinet (196). The anjo Assembly (440) has a location lug with the Cabinet (196) base. It can be lifted out following disengagement of the following: Exhaust Thermostat (229), Venting racketry (437) and Fan Housing Cover (447). Rear Access Upper For removal of the combined ack Panel (413) with Heater Unit (227), rive elt (125), rum (266), rum earings (445) and rum Front Seal (442). Remove the Top Cover (386) and withdraw the main Wiring Loom connections from the Terminal lock (142) and Heater terminals. Lay the machine flat on its front, supported to take the weight off the door and controls. With the exception of 4 screws positioned in shallow recessed channels projecting radially from the panel centre, remove all other screws in the ack Panel (413). Lift off the ack Panel (413), which will then allow access to the Heater Assembly (227), Inlet Thermostat (230) and Manual Reset TOC (228). Lift out the rum (266) and rive elt (125) after removing the ack Panel. The rum Front earings (445), rum Seal (442) and oor Microswitch (248) also become accessible at this point. For dismantling of the rum Rear earing (270), access to screws is through holes in the rum rear. Removal of one screw and the Earth Finger provides access to the earing Shaft screw. Note; it is important that the slot in the head of the shaft centre screw is filled with electrically conductive grease. Rear Access Lower The Access Panel (402) to the lower rear of the dryer only needs removing for access to the Motor (101) and associated parts, the Exhaust Thermostat (229) and Venting racketry (437). To remove the Motor Assembly (101), withdraw the Motor racket (432) securing screws from the Cabinet (196) base, remove the Screw from the Fan Cover (447) and exert anticlockwise force to disconnect if from the Fan Housing (446). The Motor Assembly can then be withdrawn. Grant Hood 2004 Page 4 04/03/2004

6 Exploded View a a a

7 Exploded View 2 445a a 537a

8 Exploded View

9 Wiring iagram F/E 1.25 EC Timer F/E A Mains Cable G Timer Connections A C A/K /K G E TL TN G* 1.0 /K G C 0.75 HESW S A 0.75 MAN TOC HE2 HE1 G* 1.0 A* /K G INTH A* 3 4 C9 C T4 M 3 4/7 5/8 A/K C11 C12 EXTH Wire Colour Code A C E F G H K N/A lack rown Red Orange Yellow Green lue Violet White Pink A/K E Component Code T S M EXTH INTH HE HESW MAN TOC A/CSW E M CAP E Terminal lock oor Switch Motor Exhaust Thermostat Inlet Thermostat Heater Heat Switch Manual Reset Heater Cutout Anticrease Switch

10 White Knight CL432 Reversing Integrated ryer Parts List Item escription Code Expl.View 101 Motor & 8µf Capacitor Assembly Pulley µf Capacitor rive elt Mains Cable (no plug) Terminal lock Cabinet Assembly Ignis Plinth a Metal Plinth Complete Flatline oor/window Assembly a Flatline oor Frame Assembly Timer EC A Heating Element Heat TOC Thermostat (exhaust) Thermostat (inlet) Rocker Switch Microswitch/racket Assembly & rum Assembly rum Shaft/earing Kit Timer Knob Assembly Control Panel Assembly Hinge Cover Flatline oor Hinge Assembly Window Flatline oor Frame a Flatline oor Handle Latch Pivot Latch Spring oor Latch Switch Strike Loom Clip Latch Guide Front Panel Assembly & Flat Top Cover Assembly Gasket Rocker utton Flex Support Clip Heater Wires Clip Heater Support Heater Plate A Access Panel Cable Clamp ack Panel Assembly Motor Spring Clip Motor Mount racket Extendable Rear Vent Kit (short) & anjo Assembly Front earing (short) Front Seal Lifter Front earing (long) a earing Pads & rush Seal Kit Fan & Access Cover Assembly & Spring Clip (Fan) utton Switch Spring Switch racket

11 White Knight CL432 Reversing Integrated ryer Parts List 454 Filter Screw 6 x 10 Countersunk Head anjo Seal J' Clip anjo Insert No 2 White anjo Insert No 1 White U' Type Captive Nut W' utton Plug Not Shown On Exploded Views Loom Assembly User Instruction ooklet MFI Fittings (Pair of Hinges, oor Stop, Spacers etc.)