DRAFT. SERVICE MANUAL Dishwasher 2005 SEVEN DIGIT

Transcription

1 SERVICE MANUAL Dishwasher 2005 SEVEN DIGIT DRAFT All the parts included in this document are the property of Indesit Company S.p.A. All rights reserved. This document and the information it contains are supplied without liability for possible errors or omissions; no part of this document can be reproduced, used or copied without written permission or without being authorised by the terms of a contract clause.

2 CONTENTS OF THE MANUAL: NOTE FOR THE ENGINEER This manual is a supporting document for technical personnel. It contains a description of the various product types, the general operating principle, and indications concerning assistance. Technical personnel should anyway consult the specific model on (servicenet.indesitcompany.com) to access data and updates of electrical diagrams, technical bulletins, and spare parts. 2

3 CONTENTS 1. TYPOLOGY OF PRODUCT 4-6 Legend 4 Interfaces 4 Technical features 5 Energy Label 6 2. FUNCTIONING 7-10 Programs 7 Program Table 8 Function setting 9 New programs 10 Other innovations COMPONENTS WIRING DIAGRAMS TECHNICAL ASSISTANCE Demo Mode 14 Auto Test 14 Rod and Sat Testing cycle Fault & Solutions 18 Trouble Shooting 19 Assembly & Disassembly EXPLODED VIEW APPENDIXES Wash diagrams

4 1. TYPOLOGY OF PRODUCT: 1.1. LEGEND: Ariston: LF 70 IT - LF 70 X IT - LF 70 FR - LF 70 EU - LF 70 X EU LL70XFR Brand + Interface L Knob LL Led LF Seven Digit LD LCD Dimensions: 4 45 cm 6 60 cm 7 Digit60 cm Interface:: Colour: S Silver IX Inox Vuoto White Country: IT Italy EU Europe FR France UK England DE Germay TK Turkey SK Scandinavia TYPE Hotpoint: FDW 70 P - FDW 70 T - FDW 70 G - FDW 75 A FDW 70P Dimension F = Full S = Slim DW =Dish Washer Interface: 4 Knob 6 Led 7 Digit 8 LCD 5 Alluminium Colour: S Silver T Sandstone G Graphite A Alluminium 1.2. INTERFACE: 3c 3h 3a 3i 3l 3b 3d 3f 3e 3g 3m 1. STAND-BY button 2. PROGRAM selector (button) 3. DISPLAY 3a. PROGRAM led 3b. LACK OF RINSE AID led 3c. LACK OF SALT led 3d. PRE-WASH led 3e. WASH led 3f. RINSES led 3g. DRYING led h. CYCLE PROGRESS leds 3i. 4IN1 led 3l. HALF LOAD led 3m. DELAY TIMER led * 4. DELAY TIMER button* 5. UPPER HALF LOAD button 6. 4IN1 button 7. START/RESET button

5 1.3. TECHNICAL FEATURES: TYPE MODEL: SEVEN DIGIT Dimensions: Width: 60 cm Height: 85 cm Depth: 60 cm Water supply: Maximum pressure: 10 bar Minimum pressure: 0,5 bar Power supply: Tension: 220/230 Volt. (EU) - 230/240 Volt. (UK) Maximum power absorbed: 2000 Watt. 5

6 1.3. ENERGY LABEL: Energy Dishwasher TYPE Manufacturer Model More efficient ARISTON LF 70 X EU A Blands Model Energy class Less efficient Energy consumption kwh/cycle (based on test results for manufacturer s standard cycle using coold fill) 1.05 Energy consumption Kw/h - normal cycles Actual consumption will depend on how the appliance is used Cleaning performance A: higher G: lower Drying performance A: higher G: lower A B C D E F G A B C D E F G Wash class Drying class Standard place settings Water consumption cycle Max load Kg Water volume (litres) - normal cycles Noise (db (A) re 1 pw) Further information is contained in product brochures Norm EN Washing machine label Directive 95/12/EC 6

7 2. FUNCTIONING: 2.1. PROGRAMS: PROGRAM SETTING: Procedura da eseguire: To set a program, follow this procedure: a. Select a program by pressing the relative button until the number of the program chosen appears on the display. b. Select other eventual wash options. OPERATION c. Start the wash by pressing the START/RESET button, the machine emits a beep to confirm the order. REMARK: three acoustic signals and the word END on the display communicates the end of the wash cycle CHANGING A PROGRAM ALREADY SET: If a program has mistakenly been selected, it is possible to change it, following this procedure: a. To reset, press and hold START/RESET button for 4 seconds, the machine emits one long beep and three short beeps. b. Follow the instruction to set a program. 7

8 PROGRAM TABLE: Ariston dishwashers are provided with an automatic system of filter cleaning, which could prolong the duration of programs. Indications to choose programs Normally dirty crockery and pots. Daily standard program. Programs Detergent (A) = Wash dispenser (B) = Pre-wash dispenser powder liquid tablets Pre-wash Drying Program length (degree of tolerance +- 10%) 30 gr (A) 30 ml (A) 1 (A) 88' OPERATION Normal An economical wash, with low energy consumption, suitable for crockery and pots. Eco 25 gr (A) 5 gr (B) 25 ml (A) 5 ml (B) 1 (A) 145' Very dirty crockery and pots (suitable for delicate pieces). Intensive 30 gr (A) 5 gr (B) 30 ml (A) 5 ml (B) 1 (A) 1 (deep dispenser) 120' An economical and fast cycle, suitable for not very dirty crockery, to be washed soon after their use. An economical and fast cycle, suitable for delicate crockery, which is more sensitive to high temperatures, soon after their use. A hygienic cycle to wash nursing-bottle, teats, dishes, cups, glasses and cutlery. Load all the crockery on the upper basket only. Fast Stemware Baby 25 gr (A) 25 ml (A) - 24' 25 gr (A) 25 ml (A) 1 (A) 96' 20 gr (A) 20 ml (A) - 60' Preliminary wash waiting for the crockery used in next meal to complete the load. Soaking 12' Remark To facilitate the dosage of detergent, it is better to know that: 1 dessert-spoon = 15 gr. of powder = 15 ml of liquid ca. 1 tea-spoon = 5 gr. of powder = 5 ml of liquid ca. 8

9 2.2. FUNCTION SETTING: DELAY TIMER: It is possible to delay the start of a program from 1 to 24 hours: 1. Press DELAY TIMER button: at every pressure the display visualizes the time selected and the led correspondent to the delay selected switches on. 2. Select a program and press START/RESET button: after a beep, the countdown begins; 3. When the time is expired, the program starts. To change the delay and select a shorter time, press DELAY TIMER button. To reset it, press the button many times until the CYCLE PROGRESS led, relative to the program selected, switches on. OPERATION HALF LOAD on the upper basket: It is used when there are few dishes to be washed to save water, energy, detergent. Before selecting a program, press HALF LOAD button; the relative LED switches on and the wash cycle starts on the upper basket only. Halve detergent quantity. It is advisable to use powder detergents. This function is not compatible with BABY and FAST programs. 4 in 1 option: To use multifunction tablets (2 in 1, 3 in 1, 4 in 1), press 4 in 1 button. This function increases the total time of a program of about 10/15 minutes. This button is not compatible with the following programs: FAST, SOAKING, BABY. 9

10 2.3. NEW PROGRAMS: Program no. 4 - FAST: It is like the traditional FAST program, but it does not accept the HALF LOAD and 4 in 1 functions, to assure detergent melting. Program no. 6 - BABY: Seven Digit dishwasher has a new program, called BABY ; it is a hygienic cycle to wash nursing-bottle, teats, dishes, cups, glasses, cutlery and all things used by children The handbook recommends to load crockery on the upper basket, but it is important to know that this cycle puts on both the basket and it is not compatible with Half Load function. It is advisable to use the upper basket because of the lower pressure of its wash arm, avoiding that the small and light cutlery used for children are expelled from the basket. This program can not be used with multifunction tablets (it does not accept 4 in 1 function) and does not supply rinse aid.. 4 in 1 option: It allows the use of multifunction tablets. The option 4 in 1: Does not restrain salt or rinse aid pilot light. Does not restrain the supply of rinse aid. Does not restrain the regeneration of the resins During the wash phase: It warms water up to reach a temperature of 55 C (in intensive level it reaches a temperature of 63 C). The wash cycle is lengthened of 10 minutes (except the intensive). The hot rinse provides: Warm up to 70 C (except for stemware). The intensive cycle does not change in the wash phase but selecting the 4 in 1 option modifies only the hot rinse (it reaches 70 C). In the Stemware cycle the 4 in 1 option increases the temperature of the hot rinse from 65 C to 68 C; the Stemware Cycle does not reach 70 C in order to protect crystal glasses from corrosion (the wash phase changes like the other cycles). The duration of the cycles, after the selection of 4 in 1 option, changes from 12 to 15 minutes. The water softener is adjusted to Minimum position; this setting allows a salt consumption equal to 25 gr./cycle. OPERATION REMARK: In appendix no. 1 are schematized the present standard features and the ones modified to permit the selection of 4 in 1 function. 10

11 2.3. OTHER INNOVATIONS: -- The electronics of this appliance permits the board RESET without unplugging the machine. To reset the appliance, press Power On + P buttons simultaneously for 5 seconds ca. Now the electronic board is reset. - Choosing Half Load option, when the machine supplies detergent, both the wash-arms run to check the eventual presence of filters clogged and to melt the detergent. - To prevent an erroneous signalling the following modification has been introduced on this platform: if the machine does not warm up, before signalling any problem in the heating circuit, it performs a control on the pressure switch. If the pressure switch is in empty position, the machine communicates FILTER CLOGGED fault, otherwise it communicates PROBLEMS ON HEATING CIRCUIT fault. OPERATION 11

12 3. COMPONENTS: The new heater is 1800 Watt - powered (the old one: 2040 Watt) and operates at a tension equal to 230 Volt and 7,8 Amp, at a resistance equal to 29,4 Ohm. Heater COMPONENTS Moreover the pump is shielded by an automaticrestoration thermal protector, which operates in case of overheating or blockage of the pump. There are two types of thermal protector: 15AM211 A on 150 ± 5 C off 105 ± 15 C placed in the middle of the coil 7AMO31AS on 120 ± 5 C off 76 ± 15 C next to the coil Drain pump The drain pump in this machine is connected independently from the wash motor (the previous machines had a series connection)

13 4. WIRING DIAGRAMS AND CONNECTIONS: WIRING DIAGRAMS 13

14 5. TECHNICAL ASSISTANCE: 5.1. DEMO MODE: Seven Digit washing machine is provided with the Demo Mode function. To select it, press and hold Power On + Start + Delay simultaneously for 5 seconds, with the machine on; the display shows the message don to confirm that the function has been selected. To deselect it, press Start/Reset and Power On simultaneously for 3 seconds; the display shows the message dof to confirm the de-selection of the function AUTO TEST: To start Auto Test, follow this procedure: 1. Switch on the dw, choose program no. 1, switch it off. 2. Switch on the dw, choose program no. 2, switch it off. 3. Switch on the dw, the display will be off to indicate that the function has been selected. Choose program no. 2 and press Start to start Auto Test SAT (program no. 1 starts the ROD testing, used in the factory to test the product). ASSISTANCE 14

15 5.3. ROD AND SAT TESTING CYCLE: 1. START OF A LONG TESTING CYCLE 2. Drain V + 0 sec. 3. Reading of turbidity sensor and pressure switch in empty state If it read a max turbidity value (clean, connected), it turns on the Rinse Aid led up to the end of the cycle If it read a min turbidity value (unclean, disconnected), it turns off the Rinse Aid led up to the end of the cycle. - If Rinse Aid led remains off, the turbidity sensor does not work or it is disconnected. Probable defects: faulty or disconnected turbidity sensor, dirty optical tube, faulty/disconnected Rinse Aid led. 4. Salt led switches on simultaneously to Rinse Aid led (up to the end of the cycle) - If the Salt led remains off, it does not work Probable defect: disconnected Salt led, faulty connection. 5. TURBINE-filling of 2 litres, in static phase + (searching of alternated wash position, washing up + down). - if the Timer does not receive any signal from the turbine, but water is filling the tank, once reached F static (1,2litri), it activates the wash motor and fills up to reach the F dynamic pressure switch, for a max time of 153 sec. from the activation of the solenoid valve. Probable defect: faulty or disconnected turbine. 6. Pause of 10 seconds, checking of HIGH PRESSURE sensor, (it must be off, stand-by position). - If H.P. sensor is on, the dw is in filter cleaning alarm. Probable defect: faulty or disconnected H.P. 7. WASH MOTOR activation. 8. TURBINE-filling of 2 litres, in dynamic phase (total 4 lt), (wash motor on). 9. I Checking pressure switch state (V - P), (wash motor on) 9.1. If it is in F (full), filling phase is finished, the dw only washes 9.2. If it is in E (empty), it fills and wash up to reach F pressure switch or a max quantity equal to 8 lt, - If at 8 lt the pressure switch has not still reached F state, the dw is in filter cleaning alarm. Probable defect: faulty pressure switch, cables disconnected/inverted. 10. WASH MOTOR on, 1 minute of preparation to filling. - In case it fills a quantity higher than 8 litres, the dw is in filter cleaning Probable defect: faulty pressure switch, cables disconnected/inverted. 11. Activation of WASH MOTOR, HEATER, ELECTRO-DISPENSER, (washing up/down) 20". 12. Checking of HIGH PRESSURE sensor 5sec. (it must be on). - If high pressure sensor is off, the dw is in filter cleaning alarm. Probable defect: faulty HP sensor - DECANTER spout clogged. 13. WASH + HEATING 1 minute 14. If the dw has selected Half Load, see point If the dw has selected the alternated wash, see point Section about the control of dw with Half Load (no alternated wash) 15.1 Deactivation of wash pump ASSISTANCE 15

16 15.2 Activation of Half Load solenoid valve 15.3 Activation of wash pump - 90 seconds 15.4 Checking the state of HIGH PRESSURE sensor 15", (washing only on the upper basket) (it must be off) - If high pressure sensor is on, Half Load solenoid valve does not work, the dw is in filter cleaning alarm Probable defect: faulty Half Load solenoid valve, cables disconnected 15.5 Deactivation of wash pump and Half Load solenoid valve 15.6 See point Section about the control of dw with Alternated Wash (no Half Load) 16.1 Deactivation of wash pump 16.2 Activation of wash motor and heater 16.3 Searching Alternated Wash position (washing only on the upper basket for 90 seconds) 16.4 Checking the state of HIGH PRESSURE sensor 15", (washing only on the upper basket) (it must be off). - If high pressure sensor is on, the Alternated Wash does not work, the dw is in filter cleaning alarm. Probable defect: faulty Alternated Wash dispenser, cables inverted/disconnected Deactivation of wash pump 16.6 Searching Alternated Wash position (washing up + down) 16.7 See point Heating up to 55 C. - If pressure switch does not reach empty state within a max time of 4 minutes, the dw goes in drain time-out. Probable defect: faulty/disconnected pump, faulty pressure switch /cables inverted. 18. Drain V +15" - If pressure switch does not reach empty state within a max time of 4 minutes, the dw goes in drain time-out Probable defect: faulty/disconnected pump, faulty pressure switch /cables inverted START OF SHORT TESTING CYCLE... CONTINUATION OF LONG TESTING CYCLE TURBINE-filling of 3 litres, in static phase. - If the turbine does not send a signal to the timer, but water fills the tank, reached the static F pressure switch (1,2litri), it activates the wash motor and loads up to reach dynamic F pressure switch, during a max time of 153 sec. from solenoid valve activation. Probable defect: faulty/disconnected turbine 21. WASH MOTOR activation. 22. TURBINE-filling of 1 litres, in dynamic phase (total 4 lt). 23. Checking pressure switch state (V - P), (wash motor on) If it is in F (full), it does not load anymore If it is in E (empty), it loads up to reach F pressure switch or a max quantity of 6 litres. - If at 6 lt the pressure switch has not still reached F state, the dw is in filter cleaning alarm. Probable defect: faulty pressure switch, cables disconnected/inverted. ASSISTANCE 16

17 24. WASH MOTOR on, 1 minute of preparation to filling. - In case it fills a quantity higher than 6 litres, the dw is in filter cleaning Probable defect: faulty pressure switch, cables disconnected/inverted. 25. Activation 10"sec. of HEATER 26. Activation 10"sec. of ELECTRO-DISPENSER 27. Activation 10"sec. of WASH MOTOR 28. Activation 15"sec. of REGENERATION SOLENOID VALVE 29. Activation V +5"sec. of DRAIN PUMP (V+5" = Empty pressure switch reached + 5 seconds) - If pressure switch does not reach empty state within a max time of 4 minutes, the dw goes in drain time-out Probable defect: faulty/disconnected pump, faulty pressure switch /cables inverted 30. Activation 10"sec. of MOTOR_FAN (if it is present, or there is a pause). 31. Activation 20"sec. of LOADING SOLENOID VALVE + DRAIN PUMP. 32. Beep emission, two leds flashes to signal the END OF THE CYCLE. REMARK: The testing cycle must completely reset as wash cycle does. ASSISTANCE 17

18 5.3. FAULT ANALISYS AND SOLUTIONS: POSSIBLE FAULT ALARM ALARM Leakage from the hydraulic system (dw equipped with turbidity sensor, check if red/black terminals on the connector are shock-circuited) Faulty drain pump, wires detached or false contact, drain tube clogged, faulty timer. Wires detached, faulty drain pump, timer triac broken. Wires disconnected or inverted on the connector or motor or timer, wash motor with faulty auxiliary start, timer triac broken Condenser wires detached, faulty/shortcircuited condenser OVERFLOW (water leakage/overflow in basin) (9 sec.) Max time to reach drain (4 min.; empty pressure switch) exceeded Unconformable electrical connection circuit on DRAIN PUMP (4 min) Unconformable electrical connection circuit on PRIMARY STARTER WASH MOTOR Unconformable electrical connection circuit on AUXILIARY STARTER WASH MOTOR Drain tube wrongly positioned, outlet too low. Strap, filter, micro-filter clogged. Timer not programmed - Wrong keyboard Faulty SV. Water tap off, faulty sv, sv wires detached. Wires disconnected, faulty sv, timer triac broken. Wires disconnected on timer/heater, faulty timer, ITR interrupted Empty PRESSURE SWITCH during wash phase Filters clogged SOFTWARE recognition error SV broken Max time (90 sec.) for turbine rotation and full pressure switch exceeded. Unconformable electric circuit of LOADING SOLENOID VALVE (90 sec.) HEATER RELAY open (9 sec.) ASSISTANCE Heater circuit wires disconnected, faulty timer relay, heater ITR not calibrated. Replace timer (faulty NTC). NTC band detached from its housing or not calibrated. Problems on wiring or timer Unconformable HEATER CIRCUIT (9 sec.) Unconformable THERMISTOR (NTC) CIRCUIT (no continuity) (9 sec.) Max time to reach washing phase T exceeded (60 min) No communication 18

19 5.4. TROUBLE SHOOTING: PROBLEM It does not switch on It does not fill itself with water It continuously fills itself with water The motor does not run It does not drain It does not wash well Loss of current ANALISYS - Check the socket. - Verify if the door closes the safety switch. - Door micro door-lock - Display board - Tap closed or low pressure - Solenoid valve clogged - Solenoid valve not supplied - Solenoid valve broken - Check motor winding - Motor terminal box or board - The motor is not under tension - Check drain pump - Drain pump blocked - Check drain pump tension - Check wall-drain - Lack of detergent - The program is not the right one - Check earth drain - Anti-noise filter ASSISTANCE 19

20 5.4 ASSEMBLY/DISASSEMBLY: Demounting the machine, its functional components are the same, therefore we are documenting only the components which have been modified in their characteristics or in their position inside the machine. Disassembly of the Main board: 1. Remove two screws fixing the plinth. 5. Disconnect the cable under the motor room. 2. Remove the plinth. 6. Make the board slide leftwards. 7. Make it go out from the hole on the left. ASSISTANCE 3. Using a flat type screwdriver, remove two plastic cover protecting the motor room. 4. Remove two screws fixing the main board. 8. Detach connectors. 20

21 Disassembly of the Display board: 3. Remove two screws fixing the main board. 1. Remove the screws around the front panel. 2. Unfasten the front panel by pulling it forward carefully. 4. Disconnect the cable. Disassembly of the NTC ASSISTANCE 1. Remove two screws fixing the plinth. 2. Remove the plinth. 3. Remove two screws fixing the sump. 4. Remove the sump. 5. Detach NTC support. 6. Pull out the NTC. 21

22 6. EXPLODED VIEW: Cabinet. Ref. Item 000 HANDBOOK IT-EN-FR-ES 001 LEFT SIDE PANEL WHITE BACK PANEL POLIONDA 003 BACK UPPER SUPPORT LS COM 004 WHITE TOP EVO3 005 PLUG TO FASTEN SHELF 006 PLUG TO FASTEN ROCKING ARM 007 DOOR GASKET BIMESCOLA 008 RIGHT-SIDE SOUND-ABSORBER 009 RIGHT SIDE PANEL WHITE BACK STOPPER BASKET SLIDE EVO3 011 UPPER BASKET SLIDE EVO3 012 PLATE/RAIL ASSY UPPER BASKET 012 CONVEX WHITE EXTERNAL DOOR EVO3 013 FRONT STOPPER BASKET SLIDE EVO3 014 ADJUSTABLE UPPER BASKET ASSY MARKII 015 BLUE FLAP UPPER BASKET EVO3 015 BLUE FLAP BABY CYCLE 015 PINK FLAP BABY CYCLE 016 BASKET HANDLE EVO3 017 LOWER BASKET ASSY EVO3 018 WHEEL BODY LOWER BASKET 019 WHEEL ASSY LOWER BASKET Ref. Item 020 LOWER BASKET WHEEL 021 INTERMEDIATE UPPER SUPPORT 022 UPPER LOWER CROSSBAR ACQUASTOP 023 STOPPER DRAIN TUBE LVS DEW BASIN INLET TUBE 025 PAD WHITE RIGHT PLINTH EVO3 026 ADJUSTABLE SHAKING-PROOF FOOT 027 TANK BOTTOM BASIN 60CM 028 CONVEX WHITE PLINTH EVO3 029 FRONT LOWER CROSSBAR 60CM NPE 030 FOOT HOLDER TYPE X LVS FOOT 155MM LVS EVIZZATE 032 PAD WHITE LEFT PLINTH EVO3 033 LEFT-SIDE SOUND-ABSORBER 034 FRONT UPPER CROSSBAR 035 FRAME TANK GASKET SUPPORT 60CM 036 COVER FRONT SUPPORT LVS CUTLERY BASKET ASSY ARISTON EVO3 039 GRILL CUTLERY BASKET NEW 040 HANDLE BASKET REGULATION EVO3 NUOVA 041 UPPER BASKET WHEEL EVO3 042 SIDE SPONGE DOOR L.I. EXPLODED VIEWS 22

23 EXTERNAL DUCT ASSEMBLY. Ref. Item Ref. Item 001 EXTERNAL DUCT ASSY (HIDDEN HEATER) EVO3 002 CAP BASKET SLIDE LVS RING NUT FIXING EXT. DUCT UPPER WASH ARM 004 SUPPLY DISPENSER ASSY EVO3 005 INNER DUCT EVO3 006 GASKET UPPER SPRAYER 007 UPPER BENT SPRAYER ASSY 009 INLET TUBE ACQUASTOP L=1470M 010 SUPPLY CABLE SCHUKO+FILTRO ANTID. 011 CENTRAL FILTER LVS EXTRACTABLE FILTER INOX LVS CYLINDRICAL PLASTIC FILTER 014 POLYESTER MICRO-FILTER 015 RING NUT FIXING SET SUMP LVS DRAIN PUMP V HZ EVO3 017 DRAIN PUMP LVS FLOAT SUPPORT OVERFLOW 019 MICRO-SWITCH ACQUASTOP 020 OVERFLOW FLOAT 021 TUBE CLIP PRESSURE SWITCH EVO3 022 PRESSURE SWITCH TUBE LVS EVO3 023 PRESSURE SWITCH EVO3 024 ADJUSTABLE WATER SOFTENER EVO3 025 NOZZLE GASKET (LVS/89) 026 RING NUT SALT NEW ARISTELLA 027 CAP SALT NEW ARISTELLA 028 FUNNEL SALT 029 RING GASKET FOR DOUBLE SOLENOID VALVE 029 DOUBLE SOLENOID VALVE EVO3 030 COVER DOUBLE SOLENOID VALVE 033 HALF LOAD SOLENOID VALVE LVS FEMALE SCREW ASSY LVS ELECTRO-PUMP 1/2CAR. V220 75W-P SPRING MOTOR SUSPENSION 037 TUBE WATER SOFTENER/CUP L.480MM LVS TUBE SOLENOID VALVE/AIR-BREAK L= CONNECTOR BASIN OVERFLOW EVO3 040 CONNECTOR GASKET OVERFLOW 041 OVERFLOW BODY EVO3 042 GASKET OR (23,81X2,62) LVS SLEEVE MOTORE UNIT 045 HIGH PRESSURE SENSOR ASSY 046 RING NUT LOWER BASE SUPPORT 047 SUPPORT LOWER MANIFOLD LVS SUPPORT HEATER SLEEVE 049 SLEEVE HEATER MOTOR 050 WASH HEATER W CM 051 LOWER PLASTIC WASH-ARM 60CM EVO3 052 RING NUT AIR DUCT BODY LVS AIR-BREAK + TURBINE EVO3 099 GREASE KIT AMBLIG.Q.A 1 GR. 099 BAND ELECTRO-PUMP FEMALE SCREW 099 BAND HIDDEN HEATER 099 BAND HYDRAULIC TUBES 2 CABLES 099 BAND SOLENOID VALVES EVO3 EXPLODED VIEWS 23

24 DRUM ASSEMBLY. Ref. Item 001 INNER DOOR ASSY L.I. MARKII 004 ELECTR. DETERGENT + RINSE AID REED 005 MICRO-SWITCH LOCK UNIT 006 LOCK UNIT DOOR EVO3 007 START BUTTON WHITE DISPLAY BOARD SEVEN DIGIT 009 ON-OFF BUTTON WHITE FRONT PANEL WHITE 27 SERIGRAPHED LF70IT 011 SOFT-TOUCH ASSY EVO3 014 RIGHT HINGE ITEM LVS HINGE ASSY LVS EVO3 Ref. Item 017 RING NUT HINGE PIN LVS2000 D=6MM 018 HINGE PIN LS615ST 019 LEFT HINGE ITEM LVS DOOR SPRING EVO3 021 TUBE HINGE SPRING 022 FORK FASTENING DOOR SPRING 023 INNER SPACER CONVEZ DOOR NEW 024 INNER SOUND-ABSORBER DOOR EVO3 099 SCREW FOR CANOE KLIP 099 FIXING SCREW INNER DOOR/ FRONT PANEL 099 FIXING SCREW HOUSING/EXTERNAL DOOR EXPLODED VIEWS 24

25 WIRING EXPLODED VIEW. EXPLODED VIEWS Ref. Item 001 DISPLAY-MODULE WIRING 002 MODULE-PRESSURE SWITCH-HEATER WIRING 003 MODULE-DOOR MICRO-SWITCH WIRING 004 MODULE-SOLENOID VALVE WIRING 005 MODULE-POWER SUPPLY-EARTH WIRING Ref. Item 007 MODULE-ELECTRO-DISPENSER WIRING 008 MODULE-ELECTRO-PUMP WIRING 009 ELECTRO-PUMP-HINGE BAR WIRING 010 MODULE-DRAIN PUMP-FLOAT WIRING 011 MODULE-TURBINE WIRING 25

26 7. APPENDIXES: Difference between normal intensive program and 4 in 1 intensive one Intensive 64 c 15' 66,5 c 5' asc.s/h2o x 5' 15' 2'+6' 2'+4' 6' 13' brill RIG. 2'+1' 2' asc.s/h2o x 20' DET resine x4' 4 in 1 intensive 64 c 15' 70 c 5' asc.s/h2o x 5' 15' 2'+6' 2'+4' 6' brill RIG. 2'+1' 2' asc.s/h2o x 20' DET resine x4' Difference between normal program and 4 in 1 normal one Normal 52 c 10' 70 c 5' asc.c/h2o x 7' 14' 2'+3' 7' 12' brill RIG. 2'+1' 2' asc.s/h2o x 5' DET resine 4' 4 in 1 normal 55 c 20' 70 c 5' asc.c/h2o x 7' 14' 2'+3' 7' brill. RIG. 2'+1' 2' asc.s/h2o x 5' DET resine 4' APPENDIX

27 Difference between normal eco program and 4 in 1 one Eco 48 c 20' 67 C 5' asc.c/h2o x 5' 18' 2'+4' 9' brill. RIG 2' 2' asc.s/h2o x 30' apertura dispenser LP resine 4' 4 in 1 eco 55 C 30' 70 c 5' asc.c/h2o x 5' 18' 2'+4' brill. RIG 2' 2' asc.s/h2o x 30' apertura dispenser LP resine 4' Difference between normal stemware program and 4 in 1 stemware one Stemware 65 c 5' asc. C/h2o x5' 52 c 5' 9' RIG 12' 46.2 C 6' 6' brill asc.s/h2o x20'c/vent 2'+1' 2' 2' resine5' colpi di calore per 3' 4 in 1 stemware 68 c 5' asc. C/h2o x5' 55 c 15' RIG 46.2 C 6' brill asc.s/h2o x20'c/vent 2'+1' 2' 2' colpi di calore per 3' resine5' APPENDIX

28 Difference between normal Auto Duo Wash and 4 in 1 Auto Duo Wash Auto Duo Wash 65 c 4' asc. C/h2o x5' 52 c 5' 14' RIG 36 C+30''mant 11' 45 c 8' asc.s/h2o x20'c/vent 1' 2'+1' 2' brill resine5' 6' colpi di calore per 3' 4 in 1 Auto Duo Wash 70 c 4' asc. C/h2o x5' 55 c 15' RIG 36 C+30''mant 11' 45 c 8' asc.s/h2o x20'c/vent 1' 2'+1' 2' brill resine5' 6' colpi di calore per 3' Difference between normal Just You program and 4 in 1 Just You one Just You 48 C 67 C 2' 11' 1' 9' 1' DET 50 C RIG. brill resine 4' 4 in 1 Just You 55 C 10' 70 C 2' 1' 1' DET 50 C RIG. resine 4' Half Load brill APPENDIX

29 Indesit Company viale Aristide Merloni, Fabriano - Italy tel telex fax