MIXER USER MANUAL B10GF/B10GFA B15GF/B15GFA K2 M K C

Transcription

1 B0GF/B0GFA BGF/BGFA bgreen bgreen blue K C K 0 yellow K M K yellow K0-ELECTROMAGNETIC SWITCH K-SAFETY COVERING SWITCH K-FLUCTUATE SAFETY SWITCH K-OVERLOAD PROTECTION SWITCH K-SWITCH MIXER USER MANUAL K0 blue C-CAPACITOR M-MOTOR blue blue

2 INDEX TROUBLE SHOOTING PARTS CATALOG OVERVIEW Trouble Possible Causes Re-cover FIGURE TRANSMISSION CASE, ARM, STAND The can't work when operate the machine. Poor contact of the electrical equipment. Check the plug. The mixing bowl out of position. Moving direction is not correct. FIGURE AXLE Leak oil. Sealing washer is damaged. Change. FIGURE GEAR AXLE FIGURE MOTOR UNIT Defficult to move the bowl up and down. The motor is overheat and speed down. Noise and over heat. Slideway is rusted. The voltage is not enough, or incorrect speed. Poor lubrication. Clean the slideway and lubrication. Check the voltage or use lower s- peed. Add or change lubrication. FIGURE FORK AND SPEED SHAFT Mixer touch the bowl. The mixing device or bowl deformed. Repair or change the bowl or mixing device. FIGURE ARM AND HANDWHEEL TYPEBOWL LIFTER UINT SPECIFICTION FIGURE HANDGRIP BOWL LIFTER UNIT Type B0GF B0GF B0GFA B0GFA BGF BGF BGFA BGFA FIGURE TURNING PLATE AND MIXING AXLE Mixer L FIGURE STANDARD ACCESSORIES Power Supply V Input Power W 0V 00 0~0V 00 0V 00 0~0V 0V 0~0V V 00 0~0V 00 OPERATION INSTRUCTION Mixing WARNING AND SPECIALATTENTION Speed r.p.m TROUBLE SHOOTING AND SPECIFICTION Maxflour Capacity(kg) ELECTRIC DIAGRAM

3 DON'T USE WATER PIPE TO WASH THE MIXER DIRECTLY; PLEASE PULL OFF THE PLUG BEFORE MAINTAINNING, AND MAKE IT MAINTAINED BY PROFESSIONALS; DON'T TOUCH THE SWITCHSAND PLUG WITH WET HAND; IF BROKEN, PLEASE STOP USINGAT ONCE THERE ISAGROUNDED NUT (SIGNED " ") IN THE MACHINE, PLEASE RECOVER IT TO ORIGIN CONDITION, DON'T CANCELTHE GROUNDED LINE; DON'T PUT HANDS INTO THE BOWL OR TOUCH THE MIXING DEVICES WH- EN WORKING; DON'TALLOW THE MINOR CLOSE TO THE MACHINE; THE MACHINE SHOULD BE FIXED ON THE DRYWOODEN SPLINTAND WO- RK IN SAFEAREA; IF THE ELECTRICALWIRE IS BROKEN, PLEASE CHANGE IT BY PROFECTIO- NALS. : french rear cover ring Mixing device III bowl BEFORE USING, PLEASE CLEAN THE BOWLAND THE MIXING DEVICES CAR- EFULLY, AND THEN INSTALLTHE BOWL ONTO THE MACHINE CORRECTLY AND TIGHTLY; WHEN CHOOSING MIXING DEVICES, PLEASE REFER TO THE OPERATION MA- NUALTO CHOSE THE CORRECT SPEED, OR IT WILL DESTORYTHE INSIDE SPA- RE PARTSAND SHORTEN THE USING LIFE OF THE MACHIE; AFTER USING, PLEASE POWER OFF THE MACHINE,AND PUT THE BOWLAND DEVICES IN THE SAFEAND CLEAN PLACEAFTER CLEANING; KEEP ENVIROMENTARROUND THE MACHINE DRY HEALTHAND SAFE. The no using pipe line sprays to wash the mixer Wet hand in no using contact switch with power supply plug. While maintaining the mixer, must pull out first the power supply plug, and from profession the personnel maintains. In order to keep safety, when using Mixing device I/II/III, Please pay attention to insert their grooves which are from the handles into the spiral pin separately. Furthermore, rising the bowl to the highest positon, so that the edge of the bowl is higher than Mixing device I/II/III working position.

4 0 0 0 screw M* cover plate screw M* bearing 0 bearing 0 bearing cover screw M*0 body rear cover screw M* breeze window screw M* arm stand capacitor board OFF 0-0V 0-0V Before using, please check power supply if it match your machine and be sure ground wire is eliable. Before testing, please take mixing device off first, in order to avoid damage machine which is match moving direction. It's necessary to change the three-phase machine if the moving direction is not match with arrow. For changing the speed: Please stop machine first before change speed in order to aviod damage gear box. capacitor seat safefy covering switch Mixing: according to the different mixing-material. Choose the different mixing devices and speed. 0 fluctuate safety switch overload protection switch A A: Be suitable for mix and stir butter, eggs, and work with in high speed, working time is less than minutes. screw Machine at a factory hour have added to note the superior quality lubricates the grease, usually the circumstance bottom can use for several years, but machine is after maintaining, must replace the lubrication grease. B C B. Be suitable for mix and stir stuffing and raw material, and work in middle speed, working time is less than 0 minutes. C: middle position is suitable for mixing dough, working time is less than 0 minutes.flour water quantity is 0%-0%.

5 cover oil seal *0*0 bearing 0 big joint gear bearing ring joint bearing ring joint gear 0 dividing ring 0 engager Mixing device I Mixing device II Mixing device III bowl spring roller gear ring plate ring bearing 00 Any agitator is easily installed by simply raising it onto the mixing, and then rotating it counter-clockwise on t- he shaft until into place. To remove, raise the agitator on the shaft until it clears the lock and then rotate clockwise and lower. All of tools are precisely fitted to the bowl, rounded corners and easily remov- Vertical sides of jaws must face on another. RIGHT WRONG Be sure to install correct position (see Figure -) and lubricate all of the pins in the sleeve drive when reassembling. Joint () must always be raised and lowe smoothly. Be sure joint sleeve as shown in Figure -. Check oil seal, if serious oil leaks from drip cup. able for cleaning. FIGURE - FIGURE - 0

6 bearing 00 gear key * gear collar gear mixing Oil seal 0*0*0 bearing 00 safety net planetary gear turning plate long collar gear stop ring inner gear cover bearing 0 0 screw M*0 ring 0 Be sure that the keys are inserted for each gear.

7 lifting bar cottor pin *0 nut M0 flat washer compression spring little knot spiral oil seal bearing 0 key * switch switch plastic 0 lifting handle bracket flat washer flange knot 0 screw M* key *0 bowl lift handle 0 screw M* screw M* 0 bearing cover fan If the motor does not work, first v- erify the power source and connection. Next, check for damaged or faulty wiring or connections inside the mixer. A noworking motor spiral bearing cover fan may be the result of inappropriate voltage, broken wires, a defective capacitor, or a defective centrifugal governor. Motor damage may also be caused by bowl overload during oil seal bearing 0 Figure - switch switch plastic mixing. Motor set includes motor,rotor and stator. Figure - is component system diagrams of motor.

8 fork shaft spring screw arm plate pull pole nut plate bearing ring speed block gear brace seat 0 spring shaft plate 0 screw M*0 sleev spiral french support french handle 0 The speed selector / shifting mechanism is designed for simplicity and reliability. It features three mixing s- 0 handle screw nut peeds. Speed selection is made by aligning the pointer of the shifter handle with the proper number on the shift selector. Stop the mixer befor making any speed changes. Apply sealant to the shift selector as- sembly, and install it. speed block fork