NO (SPST-NO) 10 A Internal installations Particularly suited for wall mounting

Transcription

1 Features PIR oveent detector for internal or external installations - wall ounting Sall size Adjustable abient light Adjustable ight On Tie Universal ounting position - perits the selection of any area for survey Series - PIR oveent detector 10 A Internal installations Particularly suited for wall ounting External installations Particularly suited for wall ounting uber of contacts Rated current/maxiu peak current A Rated voltage/maxiu switching voltage V AC 5 (120/230 V) oinal lap rating:incandescent (120/230 V) W copensated fluorescent (120/230 V) W uncopensated fluorescent (120/230 V) W halogen (120/230 V) W Standard contact aterial oinal voltage Rated power AC/ (50 Hz)/W Abient light lx ight on tie after last detection Depth of field 230/ /230 2,300 2, / 2.5/ 10 s...12 in 10 s...12 in IP 40 IP 54 1

2 Features PIR oveent detector for internal installations Ceiling ounting Sall size Adjustable abient light Adjustable ight On Tie Series - PIR oveent detector 10 A Surface ounting Output connected to supply voltage Recessed ounting Output connected to supply voltage uber of contacts Rated current/maxiu peak current A Rated voltage/maxiu switching voltage V AC 5 (120/230 V) oinal lap rating:incandescent (120/230 V) W copensated fluorescent (120/230 V) W uncopensated fluorescent (120/230 V) W halogen (120/230 V) W Standard contact aterial oinal voltage Rated power AC/ (50 Hz)/W Abient light lx ight on tie after last detection Sensing area diaeter 230/ /230 2,300 2, /1 2/1 10 s...12 in 10 s...12 in 8 8 IP 40 IP 40 2

3 18 Series - PIR oveent detector 10 A Features PIR oveent detector for internal installations, with potential free contact Applications where interface to PC or BMS is required Ceiling ounting Sall size Adjustable abient light Adjustable ight On Tie Surface ounting Output with potential free contact Recessed ounting Output with potential free contact uber of contacts Rated current/maxiu peak current A Rated voltage/maxiu switching voltage V AC 5 (230 V) oinal lap rating: incandescent (230 V) W copensated fluorescent (230 V) W uncopensated fluorescent (230 V) W halogen (230 V) W Standard contact aterial oinal voltage / Rated power AC/ (50 Hz)/W / Abient light lx ight on tie after last detection Sensing area diaeter 250/ /400 2,500 2, ,000 1, ,000 1, V 2/1 2/ s...12 in 10 s...12 in 8 8 IP 40 IP 40 3

4 18 Series - PIR oveent detector 10 A Ordering inforation Exaple: 18 series, PIR oveent detector for internal installations, wall ounting, 1 O (SPST-O) 10 A contact, V AC supply Series Type 0 = Internal installation - wall ounting 1 = External installations 2 = Internal ceiling installation - surface ounting 3 = Internal ceiling installation - recessed ounting Insulation Dielectric strength between open contacts V AC 1,000 Between supply and contact V AC 1,500 (types , ) Other data Screw torque 0.5 Max. cable size Wiring diagra Type / Type / Contact circuit 0 = Voltage output 3 = Volt-free output contact (18.21/ only) Supply voltage 024 = 24 V AC/ for types 18.21/ only 230 = V Supply version 8 = AC (50/60 Hz) o. of poles 1 = Single pole switching 1 O (SPST-O), 10 A Following the initial power-on, and power-on following a power interruption, the detector akes a hardware-software initialisation for approxiately 30 seconds. However, the behavior of the output during this 30 seconds will depend on certain circustances: - If the detector was in the On state before the power interruption, and if the lighting level is (currently) below the pre-set, then the output contact will iediately close when the power is re-applied, for the tie delay set by the potentioeter (irrespective of whether oveent is being detected). - If the detector was in the Off state before the power interruption, or if the abient light is currently over the pre-set, then the detector will not switch-on until the end of the initialisation phase (assuing oveent is then detected) = abient light 2= light on tie 1= abient light 2= light on tie Type / The output relay will reain On for the pre-set tie, following the last detection of oveent. ux level Set 2 1 1= abient light 2= light on tie Detection of oveent Contact 4

5 Mounting and orientation 18 Series - PIR oveent detector 10 A Wall ounting Surface ounting Recessed ounting Sensing area 18.01, Wall ounting Ceiling ounting Ceiling ounting ( ) Internal installations External installations Side view Plan view 18.21, Internal ceiling installation, surface ounting or recessed ounting Single installation Multiple installation Accessories Bea liiter for and PIR oveent detectors Reduces the area of survey to 2 eters diaeter (versus 8) at an installation height of 2.8 eters. 5