TRADITIONAL ROMAN SHADES

Transcription

1 TRADITIONAL ROMAN SHADES

2

3 CLASSIQUE & LUXAFLEX SIGNATURE Roman Shades Standard Bracket supplied with every blind Extension Bracket (supplied Face Fit blind only - optional for Reveal Fit blinds). Superior cord lock & pulley system Pre-drilled holes for easy installation Matching fabric pelmet Polymer covered timber headrail 33mm x 19mm, available in two fashionable colours - Light Beige & Metallic (see Colour Co-ordination Charts) Timber Tassel CLASSIQUE Roman Shade with no sew aluminium extrusion Cord Fabric Cordclip Extrusion Spline Cord cleat Bottom lathe - with optional Ellipse bottom rail CLASSIQUE Roman Shade & LUXAFLEX SIGNATURE Roman Shade with timber battens Fabric Timber Batten REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 3 of 23

4 ROMAN SHADES - MEASURING CLASSIQUE & SIGNATURE ARCHITRAVE & REVEAL FACE & REVEAL BUTT & BUTT BUTT & THRU +40mm -45mm Corners -45mm Corners BAYS -15mm -40mm -15mm *Note: Factory will allow - FACE Nil mm width, -10mm Drop - REVEAL - 10mm width, -10mm Drop REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 4 of 23

5 ROMAN SHADES - MEASURING CLASSIQUE & SIGNATURE SIDE BY SIDE BLINDS MEASURING Corners Multiple Blinds on Face ARCHITRAVE WINDOW 1 WINDOW ARCHITRAVE WINDOW 1 WINDOW 2 WINDOW Multiple Blinds in Reveal ARCHITRAVE WINDOW 1 WINDOW ARCHITRAVE WINDOW 1 WINDOW 2 WINDOW Overall Width = Outside of extrusion end caps. Corners LIGHT GAPS CLASSIQUE ROMAN SHADES 5 Light gap to extrusion (mm) Light gap to fabric (mm) SIGNATURE TIMBER BATTENS 5mm Light gap to fabric (mm) 5mm REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 5 of 23

6 CLASSIQUE roman shades - panel infomation Corners PANEL INFORMATION SIDE BY SIDE BLINDS If the side by side windows are the same drop, the panels in the CLASSIQUE Roman Shade will be equal. If the side by side windows are a different drop the panels will not be equal. 1. SAME DROP 2. DIFFERENT DROP Note: There is an acceptable 5mm tolerance between side by side extrusions. Note:Different panel sizes. NUMBER OF PANELS Corners DROP (MM) NO. OF PANELS < > * This chart is an indication only. REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 6 of 23

7 PANEL SIZE CALCULATIONS OPERATION DESCRIPTION 280MM HEADRAIL DIMENSIONS [drop (mm) - 280]/(No. of panels - 1) SHADE STACK HEIGHT Approximately 280mm LIMITATIONS MINIMUM MOUNTING SURFACE DEPTH 45MM MINIMUM DEPTH REVEAL FULLY RECESSED 50MM SHADE STACK HEIGHT Approximately 280mm CORD CONTROL LENGTH DROP (MM) CONTROL LENGTH < MM MM MM > MM REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 7 of 23

8 Side By Side Blinds Classique Romans If the side by side windows are the same drop the panels in the Roman Shade will be t he same length. I f the side b y side windows a re a different d rop the panels will not be equal. 1. Same Drop 2. Different Drop There is an acceptable 5mm t olerance between side by side extrusions. Note: Different panel sizes. REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 8 of 23

9 Options for LUXAFLEX Roman Shades 4 styles of Tassels available in Polished Chrome, Brass and Satin Chrome and an alternate Timber design. We also offer matching Polished Chrome and Polished Brass Cord Cleats. The Polished Chrome Cleat is available in 70mm whilst the Polished Brass is available in both 70 and 90mm. To order either of these options please refer to the Roman Price List pages. REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 9 of 23

10 Classique Installation Guidelines SUPPLIED WITH EACH BLIND Width < 900mm 45 x 8# Screw s 65 x 8# Screws Standar d Bracket s Extension Bracket s (Face Only) Each standard bracket will also be supplied with 2 x ( 20 x 6#) p anhead screws, 3 washers, 1 x w ing nut. Each extension bracket w ill a lso be supplied with 1 x (5mm x 25mm) threaded bolt, 1 x washer, 1 x 5mm half nut and 1 x wing nut. Width m m Width m m TOOLS REQUIRED Steel measuring tape Carpenter s level Power or battery drill and bits Flat head and Phillips head screwdrivers LOCATE PRE-DRILLED ROUT HOLES This headrail has pre-drilled rout holes. REVEAL & FACE FIT (USING SCREWS) Hold the Roman Shade inside the window frame. Note: You may need to use washers or packing to ensure level. headrail: into the top of the reveal; or from the front, into t he back o f the reveal o r the face o f the wall or architrave. If you screw the headrail into the top of the reveal, you have a 30mm slot in the headrail to allow 45MM 65MM LIFT PELMET TO SCREW THROUGH TIMBER HEADRAIL REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 10 of 23

11 FACE FIT (OUTSIDE MOUNT) USING STANDARD BRACKETS The standard installation brackets may be Reveal (inside the window frame) or Face (outside the window frame) mounted. In all cases, level mounting is critical to the operation of the shade (use a carpenter s level). Hold the Roman Shade o n the face of t he w indow and mark the position of t he b rackets to a lign with t he p re-drilled holes i n the headrail. Attach the brackets with screws provided (2 per bracket for slot in the headrail of the blind, to allow for some sideways movement to position the blind evenly on the window. FACE FIT (OUTSIDE MOUNT) USING OPTIONAL EXTENSION BRACKETS Hold the Roman Shade on the face of the window and mark the position of the brackets to align with the slots in the headrail. Attach the brackets with the screws provided (2 per bracket for face You have a 30mm slot in the headrail o f the blind, t o allow for some s ideways movement t o brackets. Insert the 5mm x 25mm threaded bolt into the bracket and secure the bolt onto the bracket with the 5mm half nut. Repeat for each bracket. You are now ready to install the blind. 5mm x 25mm Threaded Bolt 5mm Half Nut INSTALLING THE SHADE Simply slip the headrail on to the front screw of the bracket, push up. The headrail can then be secured by placing the washer over the front screw of the bracket and tightening the wing nuts. WASHER WING NUT REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 11 of 23

12 BRICK OR RENDERED SURFACES Warning: Ensure you drill no closer than 25mm from the edges of these surfaces as you may chip or break out the brick or render. 25MM FIXING TO CLEAR HANDLES, ARCHITRAVE ETC. If needing to pack out from the window to clear handles, locks, architraves etc., use a full width piece of timber as this is more stable than individual pieces of timber and Alternatively, you may use any of the optional brackets listed. D rop (mm) Extension Bracket Sections BRACKET CUT DOWN CHART The f ollowing t able will assist you t o determine t he number of extension bracket sections which can be cut off for installation. Depending on the number of folds the blind has, the illustration below indicates which sections should be cut off (dark sections). < 1001 S tandard Bracket Required > 1900 This chart is an indication only, as each blind may vary. BALLINA ROMAN SHADE, REVEAL OR FACE FIT USING STANDARD BRACKETS: Attach brackets in required position with screws ensuring all brackets are in line and level. Attach the Roman Shade to thebrackets by tilting the front of the blind to the lip in front of the bracket, blind into position. PROTECTING YOUR CHILDREN Use cord cleats. Be aware that it is possible for children to strangle in window covering cords. To reduce the possibility of such an accident, all cords must be kept out of the reach of children, including infants. Cord cleats are an effective way to implement this essential precaution. Attach the cord cleats 153mm to 305mm apart at a height of at least 1600mm above may stand on a baby cot or other furniture in an attempt to reach the cords. Once the cleats are attached, simply wrap the excess cord around them after each use of the shade, as shown. It s fast, easy, and safe. REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 12 of 23

13 Operation CLASSIQUE & LUXAFLEX SIGNATURE ROMAN SHADES: Raising and lowering of shade: To raise, pull the lift cord down together and towards the centre of the shade. To lock off in any position, simply move the cord to the outer edge to engage the cordlock. To lower, simply pull the cords towards the centre of the shade together and gently lower. Care & Cleaning Roman Shades are durable but periodic cleaning is recommended to help keep the shade looking like new. Light dusting with a feather duster is all that is needed, or you may use a damp sponge to wipe off dirt. REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 13 of 23

14 BEACH & INIKA ROMAN SHADES superior c ord lock & pulley system Beach Roman Shade with Sewn pockets Cord cleat Inika R oman s hade with timber battens Bottom lathe i n pocket o r - with optional E llipse bottom rail inserted inside p ocket instead of the lathe. REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 14 of 23

15 BEACH & INIKA ROMAN SHADES 4:1 Chain Drive Operating System Standard Bracket supplied with every blind Continuous Cord Beach Roman Shade with Sewn pockets Inika Roman shade with timber battens Bottom lathe in pocket or - with optional Ellipse bottom rail inserted inside pocket instead of the lathe. REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 15 of 23

16 ROMAN SHADES - MEASURING BEACH & INIKA ARCHITRAVE & REVEAL FACE & REVEAL BUTT & BUTT BUTT & THRU -0 +*mm -*mm -5mm *Headboard size Headboard size: 40mm, 70mm, 90mm & 120mm Corners -*mm *Headboard size Headboard size: 40mm, 70mm, 90mm & 120mm Corners -*mm BAYS -15mm -40mm Face deductions are for a 40mm headboard. -15mm REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 16 of 23

17 SIDE BY SIDE BLINDS MEASURING Multiple Blinds on Face ARCHITRAVE WINDOW 1 WINDOW ARCHITRAVE WINDOW 1 WINDOW 2 WINDOW Multiple Blinds in Reveal ARCHITRAVE WINDOW 1 WINDOW ARCHITRAVE WINDOW 1 WINDOW 2 WINDOW Overall Width = Outside of extrusion end caps. LIGHT GAPS BEACH & INIKA 5mm Light gap to fabric (mm) 5mm REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 17 of 23

18 IMPORTANT INFORMATION FOR YOU AND YOUR CUSTOMER STACKUP The stackup of a BEACH Blind will usually occupy between 250mm 350mm of the window. The stackups of blinds with different drops may be completely different, even if the blinds line up to each other. To reduce the stackup: Simply request the stackup you desire when you order. SETTLING OUT All BEACH Blinds settle out after installation. The fabric type, size, weight and environmental factors all affect the degree to which a blind settles out. Because the process of settling out is a little unpredictable, the final drop of the blind may vary by up to +/- 10mm. LIGHT AROUND THE SIDES All BEACH Blinds allow light to pass around the sides of the fabric (even when BLOCK OUT fabric is used). This is because a small operating clearance must be left around both sides of the blind. To reduce light around the sides: If practical make the blind wider than it needs to be (when face fitting) so that the blind covers more area around the window. Using a headrail with a smaller projection will also help to reduce the amount of light that sneaks around the sides of the blind. PUCKERING AND RIPPLES Puckering is completely normal and should be expected with all BEACH Blinds. It results partly from the tension that the fabric is placed under when batten pockets are stitched into the fabric, and partly from fabric shrinkage. To reduce puckering: Consider using INIKA Blinds instead of BEACH Blinds. LIGHT PINHOLES If you order a BEACH Blind made from a BLOCK OUT fabric, then pinholes of light will show through the blind wherever stitching occurs (batten pockets, side hems, base pocket). To reduce light pinholes: Consider using INIKA Blinds instead of BEACH Blinds. No pinholes will be visible along the battens. FACTORY TOLERANCE +/- 5mm is our standard manufacturing tolerance for widths and drops. We cannot accept claims for blinds made less than +/- 5mm outside the ordered make sizes. PATTERNS If you order a BEACH Blind made with a patterned fabric, please note that the grain of the pattern may not be perfectly horizontal or perfectly vertical. Blinds may exhibit up to a few centimetres of variation in the direction of the pattern from one side of the blind to the other. Sometimes the pattern may also give the impression that it is out of square at the points where the fabric rolls into the batten pockets. +/- 5MM VERTICAL JOINS If you order a blind with vertical joins, the blind will be split into 2 wings either side of the centre piece as shown in the illustration. REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 18 of 23

19 BEACH & INIKA ROMAN SHADES - PRODUCT FEATURES STANDARD BEACH AND INIKA ROMAN SHADE OPERATING SYSTEM HEADRAIL PROJECTION BASE RAIL ACORN BEACH BATTENS INIKA (Timber Battens) SIDE HEMS ALTERNATE OPTIONS CHIAN OPERATION MOTORISATION HEADRAIL PROJECTION ACORN COMMON CORDING Side operated Cord lock and pulley. Cord operated Blinds have a projection of 30mm as standard. Blinds are fitted with a profile in a 50mm sewn pocket as standard. Standard Clear Lacquered. Sewn rear pockets with 6mm round timber battens inside. Half - round timber battens. Clear lacquered, painted and stained finishes are available. Custom painting is also available, however custom staining is not. All fabrics (including polyester sheers) have 20mm stitched side hems (+/- 2mm) except PVC/Fiberglass screen fabrics as they are ultrasonically cut and sealed. Chain operated Blinds have a headrail projection of 40mm as standard. Choose from a selection of motorised options avaliable. Headboards available are 20mm (NB: without cordlock), 50mm, 60mm, 70mm, 90mm and 120mm MDF headboards. Please refer to variations & accessories for price per metre. Chrome, Brass and painted acorns are also available at an additional charge. It involves threading the cords of one blind through the headboard of its neighbouring blind. The neighbouring blind will then have two operating cords, one for itself, and one for the blind next to it. The two blinds can then be operated independently from the one location. NON OPERATIONAL BLINDS Non-operational Blinds are supplied without wheels, rings, or operating cords and are charged at 90% of the normal blind price. The application of an operating system to any non-operational blind will void warranty. SIZE LIMITATIONS OPERATING SYSTEM MINIMUM WIDTH MAXIMUM SIZES STANDARD CORD OPERATING SYSTEM 500mm 3030mm x 3000mm CHAIN LIFTING SYSTEM 500mm 3030mm x 3000mm MOTORISATION SYSTEM 800mm 3600mm x 4200mm IMPORTANT INFORMATION OVERSIZED BLINDS PANEL SPACINGS LINE UP STANDARDS Oversized blinds can become very heavy to lift, especially those made with Blockout fabrics. Motorised options are recommended for oversized blinds. Blinds panel spacings will vary according to drop. Please select one of the following options: Side by Side: we will line-up all blinds to the longest drop in the room with a +/-3mm tolerance. Surcharge applies. Please refer to pricing guide. Panel match: we will line-up all blinds to the longest drop in the room with a +/-10mm tolerance. No surcharge. Perfect blind: we will make the blind with spaces divided evenly from top to bottom, and a total number of panels being odd. No surcharge. N.B If nothing is selected the order will be placed on hold pending clarification Line up blind: the blind must line up to a perfect blind. The line up blind will have the same panel spacing as the perfect blind, but the bottom pocket will vary depending on the drop. INIKA BLIND REAR BAT- TENS The battens we apply to the rear of the blind vary according to the type of fabric used: Sheer - Rear batten will match the front battens Translucent - Rear batten will match the front battens. Blockout - Rear batten will match the Blockout coating N.B you may still choose to override our standard rear batten colours and specify a rear batten finish of your choice. This must be clearly stated when you order. A surcharge will apply. REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 19 of 23

20 Beach & Inika Installation Guidelines TOOLS REQUIRED Steel measuring tape Carpenter s level Power or battery drill and bits Flat head and Phillips head screwdrivers REVEAL & FIT THROUGH HEADBOARD (USING SCREWS) Hold the Roman Shade inside the window frame and lift the fabric out over your arm so you can access the timber headboard. Note: You may need to use washers or packing to ensure level. Screw through the headboard: into the top of the reveal; the headboard can be ordered in 20mm (no cordlock), 30mm, 40mm, 50mm, 60mm, 70mm, 90mm and 120mm. 45MM LIFT ROMAN SHADE TO SCREW THROUGH TIMBER HEADRAIL REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 20 of 23

21 FACE FIT (OUTSIDE MOUNT) USING STANDARD L BRACKETS The standard L installation brackets are used for face mounting. In all cases, level mounting is critical to the operation of the shade (use a carpenter s level). L brackets come in different sizes depending on the size of the headboard ordered. Attach the brackets with screws provided ensuring all brackets are in line and level. Position so the top of the bracket allows clearance about to sit the headboard at the ordered height. Headboards are usually 18mm thick. BRICK OR RENDERED SURFACES Warning: Ensure you drill no closer than 25mm from the edges of these surfaces as you may chip or break out the brick or render. PROTECTING YOUR CHILDREN Use cord cleats. Be aware that it is possible for children to strangle in window covering cords. To reduce the possibility of such an accident, all cords must be kept out of the reach of children, including infants. Cord cleats are an effective way to implement this essential precaution. Attach the cord cleats 153mm to 305mm apart at a height at least 1600mm from the floor. Take into account that a child may stand on a baby cot or other furniture in an attempt to reach the cords. Once the cleats are attached, simply wrap the excess cord around them after each use of the shade, as shown. It s fast, easy, and safe. REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 21 of 23

22 Operation BEACH AND INIKA ROMAN SHADES: Raising and lowering of shade: To raise, reach behind the shade and pull the lift cord towards the centre of the shade. To lock off in any position, simply move the cord to the outer edge to engage the cordlock. To lower, simply pull the cords towards the centre of the shade and gently lower. Beach and Inika Romans with cordlock operation are not suitable for reveal fit. Romans should be face fitted but if a reveal fit must be used, Beach and Inika must be ordered as chain drive or motorised. Care & Cleaning Roman Shades are durable but periodic cleaning is recommended to help keep the shade looking like new. Light dusting with a feather duster is all that is needed, or you may use a damp sponge to wipe off dirt. REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 22 of 23

23 Combining the ageless style of Roman Shades with modern day innovation now introducing PowerView Motorisation to the Beach range of Hunter Douglas Roman Shades. Hunter Douglas Roman Shades are available in an extensive assortment of fabrics that encapsulates their timeless beauty. The beauty of Roman Shades is their ability to adjust light in any room while making your windows look fantastic. Available in block out and translucent opacities they re simple, functional and attractive. PowerView Motorisation PowerView Motorisation enables intelligent motorisation across Hunter Douglas internal and external window coverings with a simple press of a button, tap of a mobile device or by scheduling scenes that will automatically activate throughout the day. PowerView Motorisation also offers personalised control options for your window coverings, providing designer handheld Pebble remotes and wall mount options. In addition, there s the PowerView App designed for Apple and Android mobile devices, providing the ultimate in connectivity at home or on the go. The proprietary wireless RF technology features increased range, two-way communication and the ability to control individual window coverings or groups whilst being whisper quiet at less than 40 dba (ISO3746). REPLACES ISSUE DATE: JUNE 2014 APPROVED BY: P.SEOUDI PAGE 23 of 23