UL Listed Available with Cl. I, Div. 2, Groups A, B, C, D rating

CCH UX Series LED Exit Signs UL Listed Available with Cl. I, Div. 2, Groups A, B, C, D rating NEMA 4X, IP66 The Cooper Crouse-Hinds CCH UX Series LED Exit Sign combines the strength and durability of die cast aluminum with architecturallypleasing aesthetics. The CCH UX Series is illuminated by LEDs, providing the customer with a long-life, low maintenance, dependable exit sign for use in conditions where reliability is crucial. Designed for the most severe environments, the CCH UX Series will provide maximum performance against rain, moisture, cold, corrosion, and dust in applications such as manufacturing plants, refineries, petrochemical and chemical plants, waste and sewage treatment facilities, food processing, and other industrial facilities. In locations deemed hazardous due to the presence of flammable vapors or gases In areas where the presence of gases or vapors may become present during an abnormal, unusual, or accidental conditions Outdoor and wet applications Where required by the National Electrical Code, Life Safety Code, or other applicable codes Features and Benefits: Wet location, outdoor rated for use in the most demanding environments Optional hazardous location rating available Dual voltage 120V/277V reduces wiring errors Heavy-duty nickel cadmium battery for long life 24-hour charge and recharge recovery time increases safety Heavy-duty injection molded polycarbonate lens protects against impact and corrosion Brown-out protection protects battery and reduces labor Heavy-duty aluminum die cast housing protects against impact and chemical resistance LEDs provide long life, even illumination, and energy savings Wide operating temperature range (-45 C to 45 C) Self-diagnostic testing reduces costs by eliminating scheduled equipment verification tests Heavy duty nickel cadmium battery for long life meets 90 minute requirements for battery operated emergency system NEMA 4X, UL50 UL924 wet location IP65, IP66 Available with NEC hazardous location rating - UL844 Class I, Division 2, Groups A, B, C, D Dimensions In Inches: Mounting: wall mount, ceiling mount, end mount Conduit Entry: top, bottom, or either side of the unit Benefits of LED Technology: Provides safe and reliable exit marking both indoors and outdoors during power failure or interruption of power to normal lighting system Long life (>50K hours) for years of maintenance-free operation Energy-efficient for lower cost of operation Low temperature operation with no loss of illumination Rugged and durable light source for the harshest of environments Temperature Performance Data: CCH UX Series Exit Sign: -45ºC (-49ºF) to 45ºC (11ºF) CCH UX-HAZ Hazardous Location Exit Sign: T6 rating at 45ºC (11ºF) Electrical Ratings: Power Supply 120V/277V dual voltage LED Exits - Red Input Power 120V = 2.7W 277V =.2W Input Current: (Max.) 120V =.07A 277V =.04A LED Exits - Green Input Power 120V = 2.W 277V =.0W Input Current: (Max.) 120V =.08A 277V =.0A Catalog Number Housing Finish Letter Color CCH UX70RSDHAZ Silver Housing Red LED CCH UX60RHAZ Silver Housing Red LED CCH UX70GSDHAZ Silver Housing Green LED CCH UX60GHAZ Silver Housing Green LED CCH UX70RSD Silver Housing Red LED CCH UX70RWHSD White Housing Red LED CCH UX70RBKSD Black Housing Red LED CCH UX60R Silver Housing Red LED CCH UX60RWH White Housing Red LED CCH UX60RBK Black Housing Red LED CCH UX70GSD Silver Housing Green LED CCH UX70GWHSD White Housing Green LED CCH UX70GBKSD Black Housing Green LED CCH UX60G Silver Housing Green LED CCH UX60GWH White Housing Green LED CCH UX60GBK Black Housing Green LED 1162 www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2012 Cooper Crouse-Hinds

CPMVFB Emergency Compact Fluorescent Continuous Operation Champ-Pak Luminaires Cl. I, Div. 2, Groups A, B, C, D Restricted Breathing Cl. I, Div. 2 & Zone 2 (Suffix S826) Certified for IEC Zone 2 (Suffix S826TB) Cl. II, Groups E, F, G; Cl. III & Simultaneous Presence* Marine & Wet Locations, R, 4, 4X; IP66 Emergency Lighting Where emergency lighting is required to permit workers in industrial areas to safely encounter their surroundings during power failures Where emergency egress lighting is required, such as: catwalks, walkways, tunnels, doorways, stairs, stairwells, ramps and aisles Indoor and outdoor wall mounting or vertical surface mounting where minimal luminaire depth is required in: Manufacturing plants and heavy industrial facilities Industrial process facilities such as refineries, chemical, petrochemical, pharmaceutical, and platforms Waste or sewage treatment plants Offshore, dockside, and harbor installations For security and safety lighting in industrial facilites for lighting of loading docks, tunnels, and stairways For marine, wet location, hose down, and corrosive environments Features and Benefits: Unique compact shallow profile design mounts virtually anywhere Side hinged cover with two screw closing for easy installation and maintenance Gray Corro-free epoxy powder coat two-piece housing provides superior corrosion resistance Unique stainless steel wire guard accessory attaches without any additional hardware for easy installation and maintenance Glass refractor provides uniform light distribution to eliminate glare Silicon gaskets make luminaire suitable for NEMA 4X, marine enviroments High power factor ballasts (+90%) are standard, which allow more luminaires per circuit NEC/CEC: Class I, Division 2, Groups A, B, C, D Class II, Class III & Simultaneous Presence (Class I, Division 2 and Class II) Class I, Zone 2 IEC: Zone 2 Ex nr IIC UL Standards: 844, 2279 Hazardous (Classified) Locations 1598 Luminaires 1598A Marine Locations CSA Standards: C22.2 No. 17 IEC Standards: 60079-15 *Consult Cooper Crouse-Hinds. Standard Materials: Luminaire housing and door frame assembly copper-free aluminum External hardware stainless steel Lens heat- and impact-resistant refractor style glass Gaskets silicon rubber Reflector aluminum light sheet Wire guard stainless steel Standard Finishes: Aluminum Corro-free epoxy powder coat Stainless steel natural Options: Description Suffix Restricted breathing construction... S826 Class I, Division 2 & Zone 2 suitability Cooler operating temperatures (T-numbers) Certified for IEC Zone 2 (Suffix S826TB)... S826TB Furnished with: Terminal Block Crimp Terminals Dedicated voltage ballasts (no MT, DT or TT) Factory assembled with lamp installed... FA Fused - projects ballast and capacitors against abnormal line conditions... S658 (Not for use in Canada) (Not for Marine use) Electrical Rating Ranges: 52 watts 120 277V, 50 60 Hz 120V, 60 Hz 47V, 60 Hz About the Battery: Bodine fluorescent battery pack ballasts are UL component recognized Sealed, maintenance-free, high temperature nickel cadmium Solid state chargers are sealed inside the ballast case 90 minute illumination time 10-year life expectancy 2-year full warranty During auxiliary use 1 lamp has continuous operation A red indicator light indicates the battery is charging Wiring instructions for a "Push-to-Test" button is supplied with the fixture Accessories: Description Cat. # Stainless steel wire guard... P55 www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2011 Cooper Crouse-Hinds 1155

CPMVFB Emergency Compact Fluorescent Continuous Operation Champ-Pak Luminaires Ordering Information Dimensions & Weights Lamp Cat. # for use Hub Size Watts with ANSI Lamps /4 NPT 26 CPMVFB2W026 Standard Voltage Ballasts NEC/UL CEC/CSA (cul) Voltage 120 277V 50 60 Hz 120V/60 Hz 47V 60 Hz Suffix /UNV /120CAN /47 Dimensions In Inches: Net Weights: Luminaire Less Guard P55 Guard 18.6 lbs. 0.5 lbs. 1156 www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2011 Cooper Crouse-Hinds

DMVF(B) Exit Sign Fluorescent Luminaire Cl. I, Div. 2; Groups A, B, C, D Restricted Breathing Cl. I, Div. 2 & Zone 2 (Suffix S826) Certified for IEC Zone 2 (Suffix S826TB) Cl. II, Groups E, F, G, Cl. III & Simultaneous Presence Marine & Wet Locations, R, 4X; IP66 DMVF(B) Exit Signs are used: In any building or enclosed area where people work Where illuminated exit signs are required To provide distinct, highly visible exit markings To indicate the direction of travel to exits In locations deemed hazardous due to the presence of flammable vapors or gases, or combustible dusts Features: Six inch letters on white glass sign panel make the word "exit" stand out boldly and clearly Housings made of die-cast copper-free aluminum (less than 0.4 of 1% copper) for strength and resistance to corrosion Mounting module equipped with integral hub set-screws for vibration resistance (ceiling and pendant mounts) Hubs are provided with an integral conduit stop and bushing to help prevent damage to field wiring during installation Epoxy powder finish and stainless steel external hardware for resistance to corrosion Long life gaskets which provide seals between mounting module, housing, and globe assembly Grounding wire for safety Cool operating design Optional emergency battery back-up operation during power outage About the Battery: Bodine fluorescent battery pack ballasts are UL component recognized Sealed, maintenance-free, high temperature nickel cadmium Solid state chargers are sealed inside the ballast case 90 minute illumination time 10-year life expectancy 2-year full warranty During emergency use 1 lamp has continuous operation A red indicator light indicates the battery is charging Wiring instructions for a "Push-to-Test" button is supplied with the fixture Energy Savings: Less wattage used with compact fluorescent lamps compared to equivalent incandescent lamps providing the same light output NEC and CEC: Class I, Division 2, Groups A, B, C, D Class II, Class III & Simultaneous Presence (Class I, Division 2 and Class II) Class I, Zone 2 IEC: Zone 2 Ex nr IIC UL Standards: 844, 2279 Hazardous (Classified) Locations 1598 Luminaires 1598A Marine Luminaires CSA Standards: C22.2 No. 17 IEC Standards: 60079-15 Standard Materials: Ballast housings and mountings copperfree aluminum (less than 0.4 of 1%) Exterior hardware stainless steel Globe heat- and impact-resistant internally fluted glass Standard Finishes: Aluminum gray epoxy powder coat Krydon material high reflectance white Stainless steel natural Options: Description Lamps supplied with exit sign... Top hat with stainless steel threaded insert... Restricted breathing construction... Class I, Division 2 & Zone 2 suitability Cooler operating temperatures (T-Numbers) Certified for IEC Zone 2... Furnished with: Terminal Block Crimp Terminals Dedicated voltage ballasts (no MT, DT or TT) Electrical Rating Ranges: 52 Watt 120 277V, 50 60 Hz 120V, 60 Hz 47V, 60 Hz Mounting Type Pendant Ceiling Wall Supply Voltage Volts/Hertz Fluorescent Cat. # Suffix S714 S806 S826 S826TB Fluorescent with Battery Back-up Cat. # 120 277V / 50 60 Hz DMVF2A052G/UNV EXD DMVFB2A052G/UNV EXD 120V / 60 Hz (Canada) DMVFB2A052G/120CAN EXD 47V / 60 Hz DMVF2A052G/47 EXD DMVFB2A052G/47 EXD 120 277V / 50 60 Hz DMVF2C052G/UNV EXD DMVFB2C052G/UNV EXD 120V / 60 Hz (Canada) DMVFB2C052G/120CAN EXD 47V / 60 Hz DMVF2C052G/47 EXD DMVFB2C052G/47 EXD 120 277V / 50 60 Hz DMVF2TW052G/UNV EXD DMVFB2TW052G/UNV EXD 120V / 60 Hz (Canada) DMVFB2TW052G/120CAN EXD 47V / 60 Hz DMVF2TW052G/47 EXD DMVFB2TW052G/47 EXD www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2011 Cooper Crouse-Hinds 1149

DMVFB Emergency Compact Fluorescent Continuous Operation Champ Luminaires Cl. I, Div. 2, Groups A, B, C, D Restricted Breathing Cl. I, Div. 2 & Zone 2 (Suffix S826) Certified for IEC Zone 2 (Suffix S826TB) Cl. II, Groups E, F, G; Cl. III & Simultaneous Presence Marine & Wet Locations, R, 4, 4X; IP66 Emergency Lighting DMVF Series Champ Lighting Luminaires are used: Where emergency lighting is required to permit workers in industrial areas to safely encounter their surroundings during power failures Where emergency egress lighting is required, such as: catwalks, walkways, tunnels, doorways, stairs, stairwells, ramps, and aisles In areas made hazardous by abnormal conditions resulting in the presence of flammable vapors or gases In areas made hazardous by the presence of combustible dusts Where combustible dusts and flammable vapors are present simultaneously In marine applications where water spray and corrosive atmospheres are considerations On installations where vibration and rough usage are problematic Where a cool, efficient light source is required In areas that require lamps to reach full illumination immediately In refineries, chemical and petrochemical facilities, grain processing, handling or storage facilities, manufacturing plants, wastewater treatment plants, sewage treatment plants, oil terminals, food processing facilities, breweries, and any other manufacturing or processing facility where safe, reliable hazardous area fluorescent or auxiliary lighting is needed Standard Features: Housings made of die-cast copper-free aluminum (less than 0.4 of 1% copper) for strength and resistance to corrosion Mounting modules equipped with integral hub set-screws for vibration resistance (ceiling, pendant, and quad mounts) Hubs are provided with an integral conduit stop and bushing to help prevent damage to field wiring during installation Epoxy powder finish and stainless steel external hardware for resistance to corrosion Long-life gaskets which provide seals between mounting module, housing, and optical assembly Grounding wire for safety Cool operating design Optional stainless steel open bottom guard permits direct access to the globe for easy relamping Battery pack ballast for emergency lighting NEC/CEC: Class I, Division 2, Groups A, B, C, D Class II, Class III & Simultaneous Presence (Class I, Division 2 and Class II) Class I, Zone 2 Emergency Lighting IEC: Zone 2 Ex nr IIC UL Standards: 844, 2279 Hazardous (Classified) Locations 1598 Luminaires 1598A Marine Locations 924 Emergency Lighting CSA Standards: C22.2 No. 17 IEC Standards: 60079-15 Standard Materials: Ballast housings and mountings copperfree aluminum (less than 0.4 of 1%) External hardware guards stainless steel Reflectors Krydon fiberglassreinforced polyester material Globe heat- and impact-resistant internally fluted glass Standard Finishes: Aluminum gray epoxy powder coat Krydon material high reflectance white Stainless steel natural Options: Description Suffix Restricted breathing construction... S826 -Class I, Division 2 & Zone 2 suitability -Cooler operating temperatures (T-numbers) Certified for IEC Zone 2... S826TB -Furnished with: Terminal Block Crimp Terminals Emergency operation only Consult Cooper-Hinds Factory assembled with lamp installed... FA Fused to protect ballast against abnormal line conditions (not for use in Canada) (not for marine use)... S658 Lamps supplied with luminaire... S714 Top hat with stainless steel threaded insert to attach ballast housing... S806 TEFLON coating on globe for increased shatter protection... S808 Electrical Rating Ranges: 52, 64, and 84 watts 120 277V, 50 60 Hz 47V, 60 Hz Accessories: (Order separately) Description Cat. # Dome RD79 0 Angle RA79 Energy Savings Less wattage used with compact fluorescent lamps compared to equivalent incandescent lamps providing the same light output About the Battery (DMVFB Units): Bodine fluorescent battery pack ballasts are UL component recognized Sealed, maintenance-free, high temperature nickel cadmium Solid state chargers are sealed inside the ballast case 90 minute illumination time 10-year life expectancy 2-year full warranty During auxiliary use 1 lamp has continuous operation A red indicator light indicates the battery is charging Wiring instructions for a "Push-to-Test" button is supplied with the fixture www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2011 Cooper Crouse-Hinds 1157

EVLPF(B) Exit Sign Fluorescent Luminaire Cl. I, Div. 1, Groups B (suffix GB), C, D Cl. I, Zone 1, Groups IIB + H2 (GB suffix), IIB Cl. II, Div. 1, Groups E, F, G; Class III, Simultaneous Presence Marine & Wet Locations, R, 4, 4X; IP66 EVLPF(B)-EXD Exit Signs are used: In any building or enclosed area where people work where illuminated exit signs are required To provide distinct, highly visible exit marking To indicate the direction of travel to exits In locations deemed hazardous due to the presence of flammable vapors, gases, or combustible dusts Features and Benefits: Six inch red letters on white glass sign panel make the word "EXIT" stand out boldly and clearly Lightweight copper-free aluminum housing with powdered epoxy finish All exterior hardware is corrosionresistant stainless steel Three mounting arrangements: pendant, ceiling, and wall bracket Integral ballast High power factor (90%+) ballasts Easier assembly, installation, and maintenance Outdoor, hose down, marine and corrosive environments suitable Ideal for adverse environments typical of industrial facilities Ground wire for safety Optional battery back-up for operation during power outage About the Battery: Bodine fluorescent battery pack ballasts are UL component recognized Sealed, maintenance-free, high temperature nickel cadmium Solid state chargers are sealed inside the ballast case 90 minute illumination time 10-year life expectancy 2-year full warranty During emergency use 1 lamp has continuous operation Red indicator light indicates the battery is charging Wiring instructions for a "Push-to-Test" button is supplied with the luminaire NEC and CEC: Class I, Division 1, Groups B (GB suffix), C, D Class I, Zone 1, Groups IIB + H2 (GB Suffix), IIB, IIA Class II, Class III & Simultaneous Presence (Class I and Class II) UL Standards: 844 Hazardous (Classified) Locations 1598 Luminaires 1598A Marine Locations CSA Standards: C22.2 No. 17 Standard Materials: Mounting modules, cover, ballast housing, globe holder copper-free aluminum Globe heat- and impact-resistant glass Exterior hardware stainless steel Standard Finishes: Copper-free aluminum Corro-free powdered epoxy Options: Description Group B suitability Factory assembled with lamps Mounting Type Pendant Ceiling Wall Supply Voltage Volts/Hertz Fluorescent Cat. # Ratings (Electrical/Size): Sources/wattage: 52W (2-26W lamps) 120-277V, 50-60 Hz 120V, 60 Hz 47V, 60 Hz Conduit entries: /4", 1" NPT pendant, wall bracket, ceiling Suffix GB FA Fluorescent with Battery Back-up Cat. # 120 277V / 50 60 Hz EVLPFA02520/UNV EXD EVLPFBA02520/UNV EXD 120V / 60 Hz (Canada) EVLPFBA02520/120CAN EXD 47V / 60 Hz EVLPFA02520/47 EXD EVLPFBA02520/47 EXD 120 277V / 50 60 Hz EVLPFCX02520/UNV EXD EVLPFBCX02520/UNV EXD 120V / 60 Hz (Canada) EVLPFBCX02520/120CAN EXD 47V / 60 Hz EVLPFCX02520/47 EXD EVLPFBCX02520/47 EXD 120 277V / 50 60 Hz EVLPFBX02520/UNV EXD EVLPFBBX02520/UNV EXD 120V / 60 Hz (Canada) EVLPFBBX02520/120CAN EXD 47V / 60 Hz EVLPFBX02520/47 EXD EVLPFBBX02520/47 EXD Energy Savings: Less wattage used with compact fluorescent lamps compared to equivalent incandescent lamps providing the same light output 1148 www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2011 Cooper Crouse-Hinds

EVLPFB Emergency Compact Fluorescent Continuous Operation Low Profile Luminaires Cl. I, Div. 1, Groups B (GB Suffix), C, D Cl. I, Zone 1, Groups IIB + H2 (GB suffix), IIB, IIA Cl. II, Div. 1, Groups E, F, G; Class III, Simultaneous Presence Marine & Wet Locations, R, 4, 4X; IP66 Emergency Lighting Cooper Crouse-Hinds Low Profile Hazard Gard Luminaires are used in: Areas that require lamps to reach full lumination immediately Where emergency lighting is required to permit workers in industrial areas to safely encounter their surroundings during power failures Where emergency lighting is required such as: catwalks, walkways, tunnels, doorways, stairs, stairwells, ramps, and aisles Areas where flammable or explosive vapors or gases are present Hazardous areas, both indoors and outdoors, where long life and low maintenance costs are desired Petroleum refineries, chemical, petrochemical and pharmaceutical plants, oil terminals, gas plants and other heavy process industry facilities Waste treatment facilities Drilling platforms and other coastal and offshore hazardous areas Features and Benefits: Small, compact size Two start Acme threaded construction Easier assembly, installation, and maintenance Lightweight copper-free aluminum housing with powdered epoxy finish All exterior hardware is corrosionresistant stainless steel Four mounting arrangements: pendant, ceiling, wall bracket, and stanchion Integral ballast High power factor (90%+) ballasts Uses same mounting modules as the standard Hazard Gard Internally fluted glass globes Krydon construction dome and angle reflectors won't rust, corrode, dent, chip, or peel Now available in components luminaire body, mounting module, guard, reflectors Three wire construction For energy conservation, luminaires can be switched off without affecting the emergency operation feature NEC/CEC: Class I, Division 1, Groups B (with GB suffix), C, D Class I, Zone 1, Groups IIB + H2 (GB Suffix), IIB, IIA Class II, Class III & Simultaneous Presence (Class I and Class II) Emergency Lighting UL Standards: 844 Hazardous (Classified) Locations 1598 Luminaires 1598A Marine Locations 924 Emergency Lighting CSA Standards: C22.2 No. 17 Standard Materials: Mounting modules, cover, ballast housing, globe holder copper-free aluminum Globe heat- and impact-resistant glass Exterior hardware stainless steel Reflectors (dome & angle) Krydon fiberglass-reinforced polyester Standard Finishes: Copper-free aluminum Corro-free powdered epoxy Krydon white Stainless steel guard Energy Savings Less wattage used with compact fluorescent lamps compared to equivalent incandescent lamps providing the same light output Options: Ratings (Electrical/Size): Sources/Wattage: Fluorescent continuous operation emergency lighting 52W (2-26W lamps) and 64W (2-2W lamps) compact fluorescent voltages Fluorescent emergency lighting 120 277V, 50 60 Hz 120V, 60 Hz 47V 60Hz Conduit entries: /4", 1" NPT pendant, wall bracket, ceiling 1 1 /4" NPT stanchion Description Suffix Group B suitability GB Fused (not for use in Canada) (not for marine use) S658* Factory assembled with lamps FA Emergency operation only Consult Cooper Crouse-Hinds *When ordering fuses for luminaires, option S658, you must specify the operating voltage. S658 cannot be ordered with /MT in the catalog number. Accessories: Description Cat. # Dome reflector RD79 Angle reflector RA79 About the Battery: Bodine fluorescent battery pack ballasts are UL component recognized Sealed, maintenance-free, high temperature nickel cadmium Solid state chargers are sealed inside the ballast case; 90 minute illumination time; 10-year life expectancy 2-year warranty During emergency use, 1 lamp has continuous operation A red indicator light indicates the battery is charging Wiring instructions for a "Push-to-Test" button is supplied with the fixture www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2011 Cooper Crouse-Hinds 1159

EXL Explosionproof Exit Sign Factory-sealed Cl. I, Div. 1 & 2, Groups C, D Cl. I, Zone 1 IIB Cl. II, Div. 1, Groups E, F, G EXL Exit Signs are used: In locations deemed hazardous due to the presence of flammable vapors or gases, or combustible dusts In any building or enclosed area where people work where illuminated exit signs are required To provide distinct, highly visible exit marking To indicate the direction of travel to exits Features: Two incandescent lamps (not included) wired in parallel to provide extra margin of light source reliability Solid state circuit for extended lamp life in AC units Six inch red letters on white acrylic sign panel make word "exit" stand out boldly and clearly Edge lighting characteristic of sign panel makes visibility excellent at all lighting levels Factory-sealed explosionproof housing Pendant, wall, and end bracket mounts provide universal installation options Impact-resistant acrylic sign panel needs no guard makes cleaning easy Internal rectifier extends lamp life beyond 1,000-hour rated life reduces relamping cost Relamping tool provided NEC: Class I, Groups C, D Class II, Groups E, F, G UL Standard: 844 NFPA Life Safety Code No. 101-1991 Standard Materials: Body copper-free aluminum Sign panel acrylic Conduit Entrance: /4" hubs Lamp Wattage: Two 60 watt, 60T10 clear lamps for AC units Two 25 watt, 25T10 clear lamps for DC units Lamps not included with luminaire Electrical Ratings: 120VDC or 120VAC operation Temperature Performance Data: (for both AC & DC operation): Ambient Temp. ( C) Class I (C, D) Class II (E, F, G) Supply Wire C 25 TC 150 C 40 TC When ordering an EXL Series Exit Sign, you will need to specify: (A) Voltage (120VAC or 120VDC) (B) Mounting (Wall, End Bracket, or Pendant) (C) Exit Sign Designation All units come standard with /4" hubs and exit signs with red lettering and white background. Complete catalog numbering is as follows: EXL (A) 2 (B) (C) (A) Voltage: 120VAC... leave blank 120VDC... D (B) Mounting: Wall... 1 End Bracket... 2 Pendant... (C) Exit Sign Designation: A Single Face (Wall Mount) AA Double Face (End Bracket & Pendant) AB Double Face, one side arrowhead right, the other no arrowhead (End Bracket & Pendant) AC Double Face, one side arrowhead left, the other no arrowheads (End Bracket & Pendant) AD Double Face, one side arrowhead both ends, the other no arrowheads (End Bracket & Pendant) B Single Face, arrowhead right (Wall Mount) BC Double Face, one side arrowhead right, the other arrowhead left (End Bracket & Pendant) BD Double Face, one side arrowhead both ends, the other arrowhead right (End Bracket & Pendant) C Single Face, arrowhead left (Wall Mount) CD Double Face, one side arrowhead both ends, the other arrowhead left (End Bracket & Pendant) D Single Face, arrowhead both ends (Wall Mount) DD Double Face, both sides arrowhead both ends (End Bracket & Pendant) Mounting Type Sign Panel Description Hub Size (In.) Pendant Style End Bracket Style AC Cat. # Wall Style DC Cat. # Wall Single face /4 EXL21A EXLD21A End Bracket Double face /4 EXL22AA EXLD22AA Pendant Double face /4 EXL2AA EXLD2AA Options: Description Suffix Exit signs with green lettering on white background... GN Unit provided with epoxy powder coat... S752 277VAC (Order ECT41 Transformer Separately) 1146 www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2011 Cooper Crouse-Hinds

EXL Explosionproof Exit Sign Factory-sealed Dimensions Dimensions In Inches: Pendant Style Wall Style End Bracket Style www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2011 Cooper Crouse-Hinds 1147

Ex-Lite LED Exit Signs Cl. I, Div. 2, Groups A, B, C, D Cl. I, Zone 1, AEx em ib IIC (NEC) Cl. I, Zone 1, Ex em ib IIC (CEC) Cl. II, Div. 2, Groups F, G (NEC) Cl. II, Div. 2, Groups E, F, G (CEC) UL Listed IP66 The Ex-Lite Series of LED exit signs are designed for hazardous locations and are ideally suited for marking escape routes and exits in potentially explosive atmospheres. The Ex-Lite Z is available as an AC only version, while the Ex-Lite ZE is available with self-contained battery. As an emergency lighting luminaire with selfcontained battery system, the Ex-Lite ZE features a nickel cadmium battery with automatic test and monitoring feature. In harsh and hazardous environments where illuminated exit signs are required Features and Benefits: LED Technology: Long life (>50K hours) for years of maintenance-free operation Energy-efficient for lower cost of operation Low temperature operation with no loss of illumination Rugged and durable light source for the harshest of environments Exit Sign System: Can be used in a hazardous location Conduit or cable entry Can be installed in moist, humid, rain, and wet environments Universal input voltage 110VAC-277VAC and 110VDC-250VDC reduces inventory Ex-Lite ZE with self-monitoring, selfdiagnostic, and test capability Premium heavy-duty nickel cadmium battery 24-hour charge and recharge time increases safety by recovering quickly from outage "EXIT" legend with alternative wings - left, right, or left and right; simple field modification Emergency lighting cycle three hours The housing of the luminaire is constructed with a corrosion resistant, robust, lightweight aluminum alloy material and illumination of the sign is provided with red, high-efficient LEDs Class I, Division 2, Groups A, B, C, D Class I, Zone 1, AEx em ib IIC (NEC) Class I, Zone 1, Ex em ib IIC (CEC) Class II, Division 2, Groups F, G (NEC) Class II, Division 2, Groups E, F, G (CEC) IP66 UL844 UL924/CSA22.2 No. 141-02 UL60079/CSA22.2 E60079 UL120/CSA22.2 E6124-1-1-02 Catalog Number Ex Lite Z Ex Lite ZE Material Number 12191001005 1219110005 Description AC/DC Exit Sign with Battery Light Source LED LED Life of LED 50K hours 50K hours Rated Voltage, VAC 120V-277V 120V-277V Frequency, Hz 50/60 50/60 Rated Voltage, DC 110V-250V 110V-250V Power Consumption 6VA 6VA Battery N/A NiCad Allowable Temperature Range -4ºF to 122ºF 41ºF to 95ºF (-20ºC to 50ºC) (5ºC to 5ºC)* Mounting Wall Wall Cable Entry Ex-e Ex-e Conduit Entry /4" /4" Protection IP66 IP66 *Due to battery chemistry, the charging capacity will be limited at temperatures below 5ºC and above 5ºC. Dimensions In (mm): www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2012 Cooper Crouse-Hinds 1161

ELPS Light-Pak Emergency Lighting System Cl. I, Div. 1 & 2, Groups C, D Cl. I, Div. 1 & 2, Groups B, C, D (with suffix GB) Cl. II, Div. 1, Groups E, F, G Cl. III Cl. I, Zone 1 Simultaneous Presence Wet Locations NEMA, R, 12 ELPS Series Emergency Lighting Systems are used: To provide safe, reliable illumination indoors or outdoors to designated areas during failure or interruption of power to the normal lighting system In areas made hazardous by the presence of flammable gases and vapors, combustible dusts, or easily ignitible fibers and flyings In areas where corrosion, vibration, moisture, dirt, and rough usage may be encountered Where required by the National Electrical Code, the Life Safety Code, or other codes In refineries, chemical and petrochemical facilities, grain processing, handling or storage facilities, manufacturing plants, wastewater treatment facilities, and other areas where safe, reliable, hazardous area emergency lighting is needed Features: Compact factory-sealed luminaire assemblies are each furnished with a 12 watt tungsten-halogen lamp and inner reflector for appropriate photometrics in hazardous areas Luminaire assemblies are fully adjustable and lockable on two axes to provide flexible and consistent light aiming capabilities Luminaire lens ring is threaded for easy relamping and locks in place with hex head set-screw; will not loosen due to vibration Ground joint cover with external flange design permits large opening and easy access to internal components; stud bolts in diagonally opposite corners of body ease cover removal and installation Neoprene cover gasket seals out moisture for superior protection of internal components against wetness and corrosion Lightweight, compact size, and mounting feet ease installation and allow placement in confined areas Two 1" NPT drilled and tapped conduit openings, with plugs, are standard, for choice of top or bottom feed Factory-installed PUSH-TO-TEST pushbutton enables easy testing of system MAIN POWER ON pilot light indicates AC power is being supplied to the battery charger; pilot light jewel is threaded for easy lamp replacement Stainless steel drain minimizes moisture collection; stainless steel breather with aluminum cap provides ventilation, minimizes moisture collection CID 101 corrosion inhibitor device is provided with each ELPS system to help protect electrical components and connections Rugged, long-life, maintenance-free, nickel cadmium battery provides 0 watts of power for the required 1 1 /2 hours Solid state battery charger for long life and reliable service prevents deep discharge by automatically disconnecting luminaires from battery Terminal block facilitates field wiring connections Instruction sheet and maintenance record card provided with unit in a protective plastic envelope A time delay is standard; time delay is preset at factory for 5 minute delay but can be field set for 5 seconds or 15 minutes, thus allowing HID type lamps time to restrike and reach desired illumination levels Solid state battery charger will accept 120, 220/240 or 277 VAC, 50/60 Hz NEC: Class I, Groups B, C, D Class II, Groups E, F, G Class III Simultaneous Presence NEMA: R, 12 (ELPS power supply) Suitable for wet locations (EVLA fixtures) Marine (EVLA fixtures) UL Standard: 844 Electric Luminaire Hazardous Locations 924 Emergency Lighting and Power Equipment 120 Explosionproof and Dust- Ignitionproof Electrical Equipment Life Safety Code: Section 5-9 (Emergency Lighting) Suitable for Wet Locations NEMA, R, 12 Marine Standard Materials: Power supply enclosure and luminaire assembly copper-free aluminum (less than 0.4 of 1% copper) Standard Finishes: Power supply enclosure and fixture assemblies powder coat epoxy paint finish Electrical Ratings: Power Supply: Input: 120, 220/240, 277 VAC, 50 or 60 Hz 0.5 Amps Maximum Output: 12 VDC UL listed for 28 watts for 1 1 /2 hours at 0 40 C Luminaires: Voltage: 12 VDC Lamp Type: #789, miniature Tungsten halogen, G4, 2-pin, 14 watt Options: Description Suffix Remote mounted lamp head and arm... EVLA12 Key operated disconnect switch as part of the ELPS502 emergency light system... S794 Keyless operated designated disconnect switch as part of the ELPS502 emergency light system... S854 Description Cat. # Standard unit with adjustable heads... ELPS502 Replacement power interior, includes circuit board and battery pack ELPS K50 Power supply... ELPS50 Lamphead and arm... EVLA12 Exit sign, double sided with EVI, red letters... ELPS502 EXD Exit sign, double sided with EVI, green letters... ELPS502 EXD GN Exit sign, single or double sided with Group B EVA, red letters... ELPS502 EXD GB Exit sign, single or double sided with Group B EVA, green letters... ELPS502 EXD GB GN Exit sign, single sided with EVI, red letters... ELPS502 EXS Exit sign, single sided with EVI, green letters... ELPS502 EXS GN Base unit comes standard with Class I, Division 1, Group B. 1150 www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2011 Cooper Crouse-Hinds

ELPS Light-Pak Emergency Lighting System Temperature Performance Data Photometric Data Dimensions and Weights Temperature Performance Data: Cat. # Class T-number Maximum Ambient Temperature 55 C I EVLA12 II* III* Maximum Ambient Temperature 40 C ELPS EVI ELPS EVA T4A TB TB TC T4 TC T4 *For Class II and Class III applications, fixtures must not be aimed more than 0 above horizontal (see diagram below). Photometric Data: Dimensions In Inches: Unit Net Weights: ELPS502 complete emergency lighting system 50 lbs. ELPS50 power supply 40 lbs. EVLA12 luminaire assembly 5 lbs. Status Indication: LED Status Condition Meaning of the Indication No light AC power is removed from the circuit Steady light (no blinking) Fully charged Light blinks once Charging Light blinks twice Battery failure Light blinks three times Circuit failure Light blinks four times Lamp failure www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2011 Cooper Crouse-Hinds 1151

LED N2LPS LIGHT-PAK Emergency Lighting System Cl. I, Div. 2, Groups B, C, D Cl. I, Zone 2 Wet Locations, Marine NEMA, R, 4X Ambient 0ºC to 55ºC LED N2LPS Light-Pak emergency lighting systems are used: To provide reliable illumination for egress areas during failure or interruption of power to the normal lighting system In areas where flammable gases or vapors may become present due to abnormal, unusual, or accidental conditions In manufacturing plants, refineries, petrochemical and chemical plants, waste and sewage treatment facilities, oil terminals, food processing facilities, breweries, and other industrial manufacturing or process industry facilities subject to wet or corrosive conditions To illuminate machinery or panels during a loss of AC power Where moisture, dirt, dust, or corrosion will limit the life and reliability of ordinary emergency lighting systems Where required by the National Electrical Code, the Life Safety Code or other applicable codes Outdoor applications Features: Compact, factory-assembled luminaire featuring LED lamps for improved lumen performance, on-time, and lamp life Nonmetallic, enclosed, and gasketed housing provides corrosion protection in the most extreme environments Durable and marine rated LED lamp head assemblies provide protection against water ingress, corrosion, and impact High temperature rated nickel cadmium battery for reliable operation up to 55ºC ambient Solid state battery charger for long life and reliable battery operation prevents deep discharge by automatically disconnecting the battery from the luminaire Factory-installed "push-to-test" button Self-test, monitoring, and diagnostics reduce costly maintenance checks Remote luminaire head assemblies (one or two) are available for mounting of luminaire heads away from main power system Stainless steel drain minimizes moisture collection Standard battery disconnect switch (Krydon unit) NEC/CEC: Class I, Division 2, Groups B, C, D, Zone 2 UL Standards: 1598A (Supplemental Requirements for Luminaires for Installation on Marine Vessels) 924 (Emergency Lighting and Power Equipment) 844 (Electric Luminaires Hazardous Locations) CSA Standards: C22.2 No. 141-M1985 unit equipment for emergency lighting C22.2 No. 17-M1981 non-incendive electrical equipment for use in Class I, Division 2 hazardous locations Life Safety Code NFPA101 Section 5-9 (Emergency Lighting) Marine wet locations suitability, Type 4X Standard Materials: Power supply and remote luminaire enclosures Krydon fiberglassreinforced polyester LED lamp head assembly epoxy powder coated stainless steel Exterior hardware nylon, plastic coated, and stainless steel Cover gasket Hypalon synthetic rubber Temperature Performance Data: Based on 55 C ambient Cat. # Class I, Division 2 N2LPS (all) 40ºC - T5; 55ºC - T4A N2RF (all) T5 Note: Ambient temperature at which the Light-Pak system is rated is 0 C to 55 C. Operation at temperatures outside this range will affect the battery life and/or charging performance. Note: Battery time in emergency mode is 90 minutes. National Electrical Code and Life Safety Code are registered trademarks of the National Fire Protection Association, Inc. Noryl is a registered trademark of General Electric Company. Electrical Ratings: Power supply Input: 120, 220, 20, 240, or 277 VAC, 50 or 60 Hz; 28 watts max. Output: 12 VDC Luminaire heads Voltage: 12 VDC; Lamp: watt LED Total lumen output: 80 Unit Net Weights: N2LPS12222 16 lbs. N2LPS12220 12 lbs. N2RF1221 8 lbs. N2RF1222 9 lbs. 1152 www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2012 Cooper Crouse-Hinds

LED N2LPS LIGHT-PAK Emergency Lighting System Cl. I, Div. 2, Groups B, C, D Cl. I, Zone 2 Wet Locations, Marine NEMA, R, 4X Ambient 0ºC to 55ºC Description Cat. # 28 watt, 12 volt power supply assembly with two watt LED lamp heads N2LPS12222 28 watt, 12 volt stainless steel power supply assembly with two watt LED lamp heads N2LPS12222 SS 28 watt, 12 volt power supply assembly less luminaire heads N2LPS12220* Remote luminaire assembly with one watt LED lamp head N2RF1221* Remote luminaire assembly with two watt LED lamp heads N2RF1222* 28 watt, 120V LED Light-Pak with single sided exit sign** N2LPS12222/120 EXS DR09174 28 watt, 277V LED Light-Pak with single sided exit sign** N2LPS12222/277 EXS DR09174 28 watt, 120V LED Light-Pak with double sided exit sign** N2LPS12222/120 EXD DR09174 28 watt, 277V LED Light-Pak with double sided exit sign** N2LPS12222/277 EXD DR09174 *Not cul approved. UL Listed only. **Exit sign operates in both normal and emergency mode. Note: Up to four (4) remote LED lamp assemblies can be connected to the N2LPS12222. Up to six (6) remote LED lamp assemblies can be connected to the N2LPS12220. Wire Sizing for Remote Installation: For Copper Wire Running Distance (ft.) Between Power Supply and Remote Luminaire Load In Watts Load In Watts Wire Size 8 16 24 2 Wire Size 8 16 24 2 16 AWG 26 1 6 10 AWG 106 5 26 1 14 AWG 42 21 10 5 8 AWG 168 84 42 21 12 AWG 66 16 8 6 AWG 270 15 67 Maximum distance to limit line voltage drop to 5%. Dimensions (N2LPS): 1.1 1.5 16.0 7.5 5.0 7.4 1.8 14.5 18.0 Standard N2LPS LED Light-Pak www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2011 Cooper Crouse-Hinds 115

LED N2LPS LIGHT-PAK Emergency Lighting System Cl. I, Div. 2, Groups B, C, D Cl. I, Zone 2 Wet Locations, Marine NEMA, R, 4X Ambient 0ºC to 55ºC Dimensions (N2LPS): EXS, EXD Option N2LPS LED Light-Pak with Optional Emergency Exit Luminaire Dimensions (N2RF): 9.50 9.50.8.8 7.27 4.8 11.77 Detail Indication Logic: Status Indication Status Description Status Definition No Light AC Power Removed from Circuit * Steady Light (No Blinks) Fully Charged *-* Light Blinks Once Battery Charging **-** Light Blinks Twice Battery Failure ***-*** Light Blinks Three Times Circuit Failure 1154 www.crouse-hinds.com US: 1-866-764-5454 CAN: 1-800-265-0502 Copyright 2011 Cooper Crouse-Hinds