Vacuum Fans A 3 diameter fan assembly is a replacement part for Vactor machines. These fans are constructed to meet exact dimensional speciþ caon and each part in the fan assembly is coated with a protectant to ensure longer life. The center steel hub assembly is welded. The welded areas are then machined to eliminate excess weld material to enhance the performance of the fan when it is spun-up to full running r.p.m. This operaon also aids in opmizing the fan into a prebalanced state. The center steel hub is then nickel-plated via electrolysis to 70 r.c., which protects it against rust and corrosion. This process also preserves the base steel against abrasive elements. The fan blades are centrifugally cast, not just die cast. Each fan blade has a tensile strength of 35,900 lbs. compared to others at 7,900 lbs. and a yield strength of 9,00 lbs. compared to others at 0,00 lbs. To safeguard against damaging abrasion, there is a hard chrome coang on the blade face. The fan blades are then pre-weighed so that all 6 fan blades in the fan assembly weigh the same, again bringing the fan closer to a pre-balanced state. The front and rear cover of each fan is anodized. This electrochemical process protects aluminum parts from corrosion and oxidaon. assembly, each fan is spin balanced to eliminate vibra stress, providing longer life for both the fan and the transmission. Each fan is supplied with a Taper Lock Bushing The fan assembly is also covered under a one-year warranty on materials and workmanship. Note: 5lbs. Fan only (Skid - 5lbs.) Made in the USA.
Fan Duct Installa on For Model 00 Vactor Type Machines 0 3 5 7 7 00 3 5 ITEM #: PART #: DESCRIPTION QUANTITY U633A Bolt - Hex Head 3/" - 6 NC x " Long 3/" 3 U6365B Flat Washer U6367B 3/" Lock Washer 5 U6360B 3/" - 6 Hex Head Nut 7 U7006** Clamp U739-Bulk 0" Kanaß ex 0 U6355D Screw, 5/ - x 3/ Hex Head U6365D 5/" Flat Washer U6367-D 5/" Lock Washer Med Spring 3 U6360-D 5/" - NC Nut U7006** Clamp 5 U576 0" Rubber Compression Inlet Boot
Vacuum Box Assembly (Vacuum Box Debris Inlet Assembly) For Model 00 Vactor Type Machines ITEM #: PART #: DESCRIPTION QUANTITY NEEDED U5596 Inlet Head Weldment U907 Centering Plate 3 U5656 Seal, Assembly Sponge Inlet U360 Weldment, Seal Frame 5 U636 Washer, Flat /" USS Zinc 6 U6366 Washer, Lock /" 7 U633E Screw, /-0 x / CAP GR 5 U777 Dustbox, Guide Angle 9 U3953 Angle Anchor - Dustbox Inlet 0 U396** Inlet Assembly U6360E Nut, Hex 3/-0 Zinc Plated U6367E Washer, Lock 3/" Hi Collar 3 U6370B Screw, 3/-0 x 3/ CAP U637-D Spring, 3/" OD x " Long 5 U377 Pin, Steel.75 DIA x.75 Long 6 U5056 Gasket - Debris Inlet Rubber 7 U5950 Head Extension Weldment
Inlet Hose Installa on For Model 00 Vactor Type Machines ITEM #: PART #: DESCRIPTION QUANTITY NEEDED U59 Clamp, King " 3 U656 " x 6" Cu U5795 " Flange Weldment Assembly 5 U655 " Flange Gasket
Inlet Hose Installa on For Model 00 Vactor Type Machines ITEM #: PART #: DESCRIPTION QUANTITY NEEDED U30 Screw, 7/-9NC x 3/ Hex Head Cap 3 U6367F Washer, Lock 7/" Zinc Plated U636F Washer, Flat 7/" SAE Zinc 5 U6065 Anchor Plate 6 U6** Inlet Weldment 7 U63 Frame, Seal Holder U697** Inlet Seal 9 U39 Screw, /-3 x / Hex Head Cap 0 U6365C Washer, /" Flat USS U0E Nut, Nylok /-3 Hex Zinc U6339C Screw, 5/6- NC x / Plated 3 U6365A Washer, Flat 5/6" U6367A Washer, Lock 5/6" 5 U639 Collar, Tube 90 x 90
TELESCOPING TUBE ASSEMBLY U603
Worm Gear Rotator Assembly This worm gear rotator assembly is the essen al drive unit to ac vate the slewing bearing ring, which ac vates the boom turret on Vac-Con combo trucks. Precision manufactured to meet the demands of the boom turret and has been perfected to be an exact replacement. Part # Descrip on Weight VC6-03 Worm Gear Rotator Assembly 5 lbs. Slewing Bearing Ring Worm Gear This slewing bearing gear is manufactured to meet the demands of the boom turret on Vac-Con manufactured combo trucks. Exact replacement. Part # Descrip on Weight VC6-03 Slewing Bearing Ring Worm Gear 59 lbs. Rota ng Front Hose Reel Bearing This front hose reel bearing Þ ts Vactor style sewer cleaning combo trucks and is precision manufactured to meet the everyday demands of this applica on. This product is an exact replacement part. Part # Descrip on Weight U55 Rotating Front Hose Reel Bearing 60 lbs. Stop Block Tooth Stop block tooth components have been precision manufactured to meet the applica on demands of restric ng a Vactor machine s front hose reel from rota ng. Part # Descrip on A achment Hole U697 Stop Block Tooth Center U697D Stop Block Tooth Offset