TechBook. in.k300tm. Bright LCD screen Spa function icons Affordable. the essential spa keypad

Transcription

1 TechBook in.k00tm the essential spa keypad Bright LCD screen Spa function icons Affordable

2 in.k00 TechBook Table of contents Warnings 2 Introduction in.k00 keypad layout 4 Installation of in.k00 4 Drilling template 5 Installation notes 6 Connecting in.k00 keypad to the spa pack 6 Keypad functions 7 Start or stop accessories 7 Water temperature 7 Off Mode 7 Programming steps 8 Program menu 8 Setting the clock 8 Programming the filter/ purge cycles 8 Setting filter or purge cycle start time 9 Setting filter cycle duration 9 Setting filter or purge cycle frequency 9 Setting economy mode 9 Setting economy start time 9 Setting economy duration 10 Setting temperature unit 10 Smart Winter Mode 10 Cooldown 10 Water temperature regulation 10 Error messages 11 Specifications 12 1

3 in.k00 TechBook Warnings WARNINGS: Before installing or connecting the unit, please read the following. FAILURE TO COMPLY WITH THE FOLLOWING WARNINGS MAY SIGNIFICANTLY SHORTEN THE PRODUCT S LIFE TIME, AND LEAD TO FAILURES AS WELL AS HAZARDOUS CONDITIONS*. COMMON SENSE MUST ALWAYS PREVAIL WHEN EVALUATING THE INSTALLATION AND/OR USE OF ANY ELECTRONIC CONTROL IN A FINAL APPLICATION. RESPECT ENVIRONMENTAL CONDITIONS LISTED AT END OF TECHBOOK. THIS UNIT MUST BE INSTALLED BY QUALIFIED PERSONNEL. ONLY QUALIFIED PERSONNEL ARE TO SERVICE THIS UNIT. THERE ARE NO USER SERVICEABLE PARTS INSIDE. THIS UNIT SHOULD BE INSTALLED ON A CLEAN FLAT SURFACE. THE GASKET ON THE BACK OF THE UNIT WILL PREVENT WATER INFILTRATION INSIDE, BEHIND THE MOUNTED SURFACE. IF THE GASKET IS DAMAGED, SEAL THE BACK OF THE UNIT WITH SILICONE TO AVOID ANY LEAKAGE BEHIND THE MOUNTED SURFACE. THIS UNIT MUST BE MOUNTED ON THE OUTSIDE EDGE OF THE SPA. SEE INSTALLATION SECTION FOR DETAILS. THE BACK OF THIS UNIT SHOULD NOT BE ENCLOSED IN A WAY THAT CAUSES WATER TO COLLECT SEE INSTALLATION SECTION FOR DETAILS. * HAZARDOUS CONDITION: A CONDITION THAT IS POTENTIALLY DAMAGING AND/OR DANGEROUS TO THE OPERATOR OR SURROUNDINGS. THIS INCLUDES, BUT IS NOT LIMITED TO: FIRE, FLOODING OR OTHER WATER DAMAGE, DIELECTRIC BREAKDOWNS (PRESENCE OF HIGH VOLTAGE), ETC. MAINTENANCE If you have problems, do not attempt to repair the unit yourself. Return it to your dealer or service station for servicing. ACCESSORY PARTS Be sure to use only the specified accessory parts. Use of other than designated parts may damage this unit internally or may not securely install the unit in place. This may cause parts to become loose resulting in hazards or product failure. DISPOSAL OF THE PRODUCT The appliance (or the product) must be disposed of separately in accordance with the local waste disposal legislation in force. Compatible spa packs: in.xm2, in.xe, in.yt, in.yj, and in.ye with compatible software revision. Aeware, Gecko, and their respective logos are Registered Trademarks of Gecko Alliance Group. in.k00, in.xm2, in.xe, in.yt, in.ye, and in.yj and their respective logos are trademarks of Gecko Alliance Group. 2 All other product or company names that may be mentioned in this publication are tradenames, trademarks or registered trademarks of their respective owners.

4 in.k00 TechBook Introduction in.k00 the essential spa keypad The in.k00 brings all the features you really need to one keypad. Compact, with a big LCD screen; bright enough to be seen in day, simple enough to use in the middle of the night; affordable, yet solidly built. Item in.k00 Static LCD size (as measured diagonally) 1.5" Optional mounting with wing-nuts and spacers Double-sided bezel gasket Icons giving instant spa status information Number of pumps/blowers supported 1 or 2 Time display

5 in.k00 TechBook in.k00 keypad layout 1 Pump Model Pump 1 Light Up Smart Winter Mode Heater Filter Set Point Indicator lights Down 2 Pump Model Pump 1 Pump 2 Light Indicator lights Up / Down Installation of in.k00 Gasket with or without adhesive Optional wing nuts and spacers To install the in.k00, use the drilling template provided in this section. Determine the mounting location and stick the template on chosen location. Cut out an opening according to the template. Clean the installation surface and peel the adhesive gasket from the back of the keypad. Insert keypad and align it correctly, then ensure it is properly glued by gently pressing evenly on the entire surface. 4

6 in.k00 TechBook Drilling template 1.44" 6.58 mm 5.17" 11.2 mm 5.67" mm R0.25" 6.5 mm R0.25" 6.5 mm 5

7 in.k00 TechBook Installation notes Keypad placement Vent hole on back of keypad should not be blocked. The back of the in.k00 should not be enclosed where water can gather, but instead cut out. It is recommended to install the in.k00 on the outside edge of the hot tub, so that it is not subject to moisture trapped by the cover. Connecting in.k00 keypad to the spa pack Main keypad in.k00 To connect the in.k00 keypad, simply insert its in.link connector into the appropriate keypad connector of the pack enclosure (as illustrated). 6

8 in.k00 TechBook Keypad functions Start or stop accessories To start or stop an accessory, press the associated button. Indicators will light up when the associated accessory is on. When an accessory has more than two states, press the button until it reaches the desired state. Indicators will flash when dual speed pumps are on at low speed, and will be solid at high speed. If you have a blower it will be controlled by the Pump 2 key. The order of actions is as follows: pump 2 on; pump 2 high speed (if applicable); blower on; pump 2 off; blower off. Water temperature The temperature shown on screen is the current water temperature. Use the Up and Down buttons to set the desired temperature. The set point icon will appear at the top of the screen. After seconds without any change to the set temperature value, the keypad will resume the normal display Off Mode Pressing Pump 1 for 5 seconds will enable the Off mode. This mode allows you to stop all outputs including automatic functions such as filter cycle, heat request and smart winter mode for 0 minutes to perform quick spa maintenance. When Off mode is active, the display will toggle between the OFF message, the clock and the water temperature. The spa light will flash for a few seconds before the end of the 0 minutes to warn you that the system is about to resume its normal operation. Press Pump 1 or Pump 2 (if available) to restart the system before the expiration of the 0 minute delay. When the system resumes its normal operation, the display shows On for seconds. 7

9 in.k00 TechBook Programming steps Program menu The program menu is accessible by holding down the Light key for 5 seconds. In the program menu the following parameters can be set: clock, filter or purge cycles, economy mode and temperature units. While in the program menu, use the Up or Down key to adjust the parameters and use the Light key to jump to the next parameter. The changes will be saved after the confirmation of the last parameter only. If there is no action taken for 10 seconds, the system will exit the program menu without saving any changes. Setting the clock Enter the program menu by holding down the Light key for 5 seconds. The display will show the current clock setting with the hour flashing. Depending on factory settings your system may be set to 24-hour time or 12-hour time. Setting the hour: Use the arrow keys to adjust the hour Press the Light key to jump to the next parameter, the minutes. Setting the minutes: Use the arrow keys to adjust the minutes. Press the Light key to jump to the next parameter, the filter or purge start time (FS). Programming the filter/ purge cycles Depending on system configuration your spa will perform either a filter or a purge cycle. The filter cycle menu consists of the following parameters: the start time (FS), the duration (Fd) and the frequency (FF). The purge cycle menu consists of the following parameters: the start time (FS) and the frequency (FF). A filter cycle consists of starting all the pumps and blower in high speed for 1 minute (purge step) then, the pump associated with the filter will run in low speed for the remaining duration of the filter cycle (clean step). A purge cycle is used when the spa is equipped with a 24 hour circulation pump which provides a continuous clean step. It consists of starting all the pumps and blower in high speed for 1 minute. 8

10 in.k00 TechBook Setting filter or purge cycle start time The display will show FSxx, xx representing the starting hour of the cycle. Use the arrow keys to adjust the hours. Use the Light key to jump to the next parameter, filter duration (Fd). Setting filter cycle duration (not available on purge systems) The display will show Fdxx, xx representing the duration in hours of the filter cycle. Use the arrow keys to adjust the duration. Use the Light key to jump to the next parameter, filter or purge frequency (FF). 0 = no filtration 24 = continuous filtration It is not recommended to set this to "0". Setting filter or purge cycle frequency The display will show FFxx, xx representing the number of cycles per day. Use the arrow keys to adjust the frequency Use the Light key to jump to the next parameter, economy mode (EP). The Filter indicator lights up when filter is on and flashes when suspended. Setting economy mode This mode allows you to lower the temperature set point of the spa by 20 F (11 C) during a certain period of the day. The display will show EPx, x representing the state of the programmed economy (0 = disabled, 1 = enabled). Use the arrow keys to enable or disable economy mode. Use the Light key to jump to the next parameter, economy start time (ES). When the Economy mode is ON, the display will toggle between the Eco message, the time, and the water temperature. Setting economy start time The display will show ESxx, xx representing the hour at which the economy mode will become active. Use the arrow keys to adjust the hour. Use the Light key to jump to the next parameter, economy duration (Ed). 9

11 in.k00 TechBook Setting economy duration The display will show Edxx, xx representing the duration in hours of the economy mode. Use the arrow keys to adjust the hour. Use the Light key to jump to the next parameter, temperature unit. 24 = continuous economy Setting temperature unit Water temperature can be displayed in either Fahrenheit ( F) or Celsius ( C). The display will show F or C. Use the arrow keys to change the setting. Use the Program or Light key to save all the parameters. Smart Winter Mode Our Smart Winter Mode protects your system from the cold by turning pumps on several times a day to prevent water from freezing in pipes. The SWM indicator lights up when freezing is detected and flashes when the purge is active. Cooldown After heating the spa water to the desired Set Point, the heater is turned off, but its associated pump (Pump 1 low-speed or CP) remains on for a predetermined period of time to ensure adequate cooling of the heating element, prolonging its useful life. Water temperature regulation Every 15 to 90 minutes the pump will run to ensure accurate water temperature readings as well as avoid heater activation in dry conditions. After verifying pump activation and taking a water temperature reading if required, the system automatically turns the heater on to reach and maintain water temperature at Set Point. Indicator flashes when taking water temperature reading. 10

12 in.k00 TechBook Error messages The list below shows the different error messages that can appear on the home screen. Refer to the troubleshooting and error codes section of the TechBook for your spa pack for more details. Code HL FLO FLO HR OH Prr AOH FLC SP in FrEr RH NC RH ID SC ER F1 F2 F Hr UPL BL Message Warning! HL Error No flow for more than 2 hours No flow condition Danger! Relay stuck Warning! Spa temp. high Warning! Temp. probes defective Internal pack temp. high Flow switch closed Input voltage issue The input frequency is out of range Comm. error in.xm2 - in.therm in.xm2 - in.therm incompatible Learning mode error in.xm2 Fuse # 1 is blown in.xm2 Fuse # 2 is blown in.xm2 Fuse # is blown Danger! Thermal fuse error The spa pack does not have valid software. Please insert valid in.stick to reprogram spa pack. The spa pack does not have valid software. Please insert valid in.stick to reprogram spa pack. 11

13 in.k00 TechBook Specifications Part number 1 pump model: pump model: Model IN.K00-CL-GE1 Environmental Operating temperature: Storage temperature: Humidity: Water ingress protection: -68 F (-20 C) to 149 F (65 C) -22 F (-0 C) to 185 F (85 C) Up to 70% condensing IPX-5 Mechanical Weight: 0.69 lb (1 g) Dimensions (W x H x D): 2.25 x 6.0 x 1.87 (57.15 mm x mm x mm) Compatibility in.yj, in.yt, in.ye, in.xe, or in.xm2 spa packs with appropriate software revision Specifications and design are subject to change without prior notice. 12

14 A Rev Gecko Alliance 450 des Canetons, Quebec City (Qc), G2E 5W6 Canada, GECKO 9225 Stellar Court, Corona, CA 9288 USA, Groupe Gecko Alliance Inc., 201 All trademarks or registered trademarks are the property of their respective owners. Printed in Canada