Technical instructions

Size: px

Start display at page:

Download "Technical instructions"

Charles Nelson
5 years ago
Views:

1 FILTER REPLACEMENT 1 ATTENTION: the replacement and insertion of the filter must be effectuated with the machine turned off. 1. REMOVE THE WATER TANK FROM THE MACHINE 2. FILL THE WATER TANK TO THE MAXIMUM LEVEL. IMMERSE THE FILTER UPSIDE DOWN (FIGURE 1) HOLDING IT WITH TWO FINGERS 2 4. WHILST LIGHTLY PRESSING THE FILTER DOWN WITH THE FINGERS FILL IT WITH WATER 5. EMPTY THE WATER FROM THE TANK 6. INSERT THE FILTER IN ITS POSITION WITHIN THE WATER TANK APPLYING GENTLE PRESSURE AND ROTATE 7. FILL THE WATER TANK UP TO THE MAXIMUM LEVEL WITH WATER AND REPOSITION ON THE BACK OF THE MACHINE

2 LOADING CARD FOR MODELS FREEDOM C11/E11 1. TURN OFF THE MACHINE (FIG. 1) 2. INSERT THE CARD IN THE APPROPRIATE FISSURE (FIG. 2). TURN ON MACHINE (FIG. ) 4 4. THE REQUEST TO RECHARGE WILL BE VISABLE ON THE DISPLAY 5 5. CONFIRM BY PRESSING ANY OF THE SUPPLY SWITCHES (FIG.4) 6 6. REMOVE THE DISPOSABLE CARD (FIG.5) WHICH CAN THEN BE DISPOSED OF It is possible to load more cards onto the machine up to a maximum Supply of 900 driks

3 LOADING CARD FOR MODELS FREEDOM C09/E09 1. TURN OFF THE MACHINE (FIG. 1) 2. INSERT THE CARD IN THE APPROPRIATE FISSURE (FIG. 2) 4. TURN ON MACHINE (FIG. ) AN ACUSTIC SOUND AND THE LED LIGHTING UP BLUE ON THE SUPPLY BUTTON SIGNALS THAT THE CREDITS HAVE BEEN LOADED 4. REMOVE THE CARD (FIG. 4) WHICH CAN THEN BE DISPOSED OF It is possible to load more cards onto the machine up until a maximum supply of 900 drinks ATTENTION: the lack of credit is evidenced by the blue led on the supply button turning off

MACHINE HEATING WILL APPEAR ON DISPLAY WAIT UNTIL THE MESSAGE READY APPEARS, THIS OCCURS WHEN THE STEAM BOILER HAS

4 INSERTION OF STEAM ARM ACCESSORY 1. REMOVE THE CLOSURE CAP (FIG.1) TURNING IN ANTICLOCKWISE DIRECTION 2. INSERT STEAM ARM ACCESSORY PUSHING AND TURNING IN CLOCKWISE DIRECTION (FIG.2) 4. MACHINE HEATING WILL APPEAR ON DISPLAY WAIT UNTIL THE MESSAGE READY APPEARS, THIS OCCURS WHEN THE STEAM BOILER HAS REACHED THE PREDETERMINED TEMPERATURE 4. TO RELEASE STEAM PRESS AND HOLD STEAM/VAPORE BUTTON ATTENTION: do not remove this accessory until the steam has ceased to come out

Lift the left side of the machine and place the milk thermos container base beside it in order to insert the two hooks on the base into their position underneath the machine (fig. ) 4 4.

5 INSERTION OF CAPPUCCINO ACCESSORY, MODELS FREEDOM C11/E11 1. Remove the closure cap (fig. 1) turning in anticlockwise direction 2. Insert cappuccino accessory pushing and turning in clockwise direction (fig. 2). Lift the left side of the machine and place the milk thermos container base beside it in order to insert the two hooks on the base into their position underneath the machine (fig. ) 4 4. Place the milk thermos container in position (fig. 4) 5. Connect the silicone tubes. The longest part must be positioned inside the container whereas the shorter part is inserted in the milk frother (fig. 5) Fill the container with milk (max lt.1) replace the cover wait until ready appears on the display To regulate the density of the froth turn the regulator positioned on the milk frother (fig. 6)

6 CLEANING PROCEDURE FOR FREEDOM MACHINE C11/E11 1. REMOVE THERMOS CONTAINER AND PLACE A GLASS OF WATER ON THE BASE (FIG. 1) 2. ADD 5CC OF CLEANING SOLUTION PITTI MASTER CLEAN TO WATER (FIG. 2). PLACE AN EMPTY GLASS UNDER THE MILK NOZZLE (FIG. ) 4 4. PRESS AND HOLD CAPPUCCINO BUTTON FOR 5 SECONDS AND THE CLEANING CYCLE WILL BEGIN.DURATION OF CLEANING CYCLE AROUND 10 SECONDS 5. REPEAT THE CLEANING CYCLE USING CLEAN WATER ONLY IN ORDER TO RINSE ONCE THE CLEANING PROCESS IS COMPLETE REPOSITION MILK THERMOS CONTAINER

IMPRESSA F7 Quick Reference Guide

IMPRESSA F7 Quick Reference Guide The IMPRESSA F7 Instructions for Use together with these short instructions IMPRESSA F7 Quick Reference Guide has been awarded the seal of approval by the independent