ENVIRONMENTAL EQUIPMENT Poly-Vent

Transcription

1 Poly-Vent The Vanishing Window Poly-Vent is a modern alternative to inefficient and cumbersome roll-up vents. Heavy-duty, clear, UV-stabilized polyethylene opens from the top down without any moving parts except blowers. It can be controlled by thermostat and acts as an insulator with six inches of air space when inflated. Poly-Vent presents an energy-efficient, airtight seal the length of the opening and can be used in existing structures to start giving your plants the air they need. Benefits: Poly-Vent II operates either fully open or fully closed. Poly-Vent III operates fully open, fully closed, or open approx Available in 3, 4,and 5 height. Custom lengths available. Adaptable to all types of greenhouses. Can mount on outside of greenhouse frame without loss of space inside house. Opens from top down to prevent cold air dump on plants. Poly-Vent II NOMINAL SIZE END PACK PVII36 PVII48 PVII60 PVIIEP36 PVIIEP48 PVIIEP60 Poly-Vent III NOMINAL SIZE END PACK* PVIII36 PVIII48 PVIII60 PVIIIEP36 PVIIIEP48 PVIIIEP60 Note: Actual working height is always 2 less than normal sizes. Pricing includes top and bottom 24 gauge galvanized gutter, guides and rear guides. *Ends packages include sheet metal enclosures for both ends of frame, 2 rear guides, blower, -3 diameter flex tube, and 4 air transfer gaskets. Poly-Vent II is similar to Poly-Vent II, except it has 2 blowers, 2-3 diameter flex tubes and 6 air transfer gaskets. OTHER SIZES ARE AVAILABLE. IMPORTANT!!! WE RECOMEMND A BACK UP POWER SOURCE TO KEEP VENT INFLATED IN THE EVENT OF A POWER FAILURE. 2 V BLOWERS ARE AVAILABLE Replacement Tubes for Poly-Vent SIZE Poly-Vent II Poly-Vent III Nominal Size Working Height Item # Item # PVII36T PVIII36T PVII48T PVIII48T PVII60T PVIII60T Cut and seal charge is $25 per tube piece

2 Fans All aluminum construction. Six-bladed propeller utilizing a cambered-twist blade design with an unique dihedral tip for higher air flow capacities at less horsepower Non-overloading design maintains horsepower within catalog range of static pressure, resulting in lower motor load and reduced operating costs Streamlined orifice insures higher air flow capacity Available mounted in either slant or square wall housing Slant Wall Housing Energy Saving - with inside shutter saves up to 3750 BTU/HR heat loss per fan High Flow capacity - shutter directs air to fan-select fan at 0.05" sp. instead of 0.0" Weather Protected - slant arrangement protects motor and drives from the elements Includes " x /2" guard on outlet sides Shutter and inlet guard held in place with quick release clips Wiring knockout included to allow all wiring connections for motor to be made inside the building Fan Size 30" 30" 30" 42" 42" 42" 48" 48" 48" 54" 54" Crated Fan With Knock Down Slant Housing, Guards and Shutter ADCA24EKD ADCA24FKD ADCA24GKD ADCA24HKD ADCA30FKD ADCA30GKD ADCA30HKD ADCA36FKD ADCA36GKD ADCA36HKD ADCA36JKD ADCA42GKD ADCA42HKD ADCA42JKD ADCA48GKD ADCA48HKD ADCA48JKD ADCA54JKD ADCA54KKD HP CFM 0.05 SP /4 -/ Inside Framed Opening Dimensions A B C 28-" 28-" 28-" 28-" 34-" 34-" 34-" 40-" 40-" 40-" 40-" 46-" 46-" 46-" 54-" 54-" 54-" 60-" 60-" 30-" 30-" 30-" 30-" 36-/2" 36-/2" 36-/2" 42-" 42-" 42-" 42-" 49" 49" 49" 57-/4" 57-/4" 57-/4" 63-/2" 63-/2" 3-7/8" 3-7/8" 3-7/8" 3-7/8" 34-/4" 34-/4" 34-/4" 34-/8" 34-/8" 34-/8" 34-/8" 36-" 36-" 36-" 40-7/8" 40-7/8" 40-7/8" 39-/2" 39-/2"

3 Aluminum Wall Shutter Corrosion resistant heavy gauge aluminum frame Precision counterbalanced aluminum blades open easier, wider to permit higher fan capacity Nylon bearings throughout are corrosion proof to help prevent sticking Suitable for dusty or humid applications Stainless steel hinge pins that will not rust, insure easy positive blade action All shutter blades are reinforced with polished galvanized steel rods, and equipped with double tie-rods Automatic - Used with exhaust fans opens automatically when fan is on, closes automatically when fan is off Keeps out wind, rain and backdrafts when fan is not in operation New cam pulley operator provides long life to motor and is corrosion resistant Motor draws only 7 watts WAAC models are center pivoted to open easier against house static pressure Motors available in 24v, 5v, 230v, and 460v (specify when ordering) Sold separately from the aluminum wall shutters but is used in conjunction WAAC88MT WAAC2626MT WAAC3333MT WAAC4040MT WAAC638MT WAAC6340MT WAAC6362MT Dimensions Overall Opening Sq. Ft. Opening WT. 8 x 8 26 x x x x 8 63 x x 62 5 x 5 23 x x x x 5 60 x x HAF Fans The HAF stands for Horizontal Air Flow. The HAF fan improves growing conditions by keeping a steady, gentle flow of air around plants to reduce mildew and disease problems while eliminating problem micro-climates which infringe upon even crop growth. Propeller - Aluminum blades held securely in place by a steel spider and hub provide quiet operation. Motor - Heavy duty PSC, totally enclosed motor with automatic thermal overload protection and ball bearings that is energy efficient. Motor can be used with variable speed control for more precise air movement. Guards - Two piece wire guard for easy access has a gray plastic coating to resist corrosion. Installation - Two piece rotational bracket provides a locking tilt adjustment for proper angle of air flow. S bracket provides two different dimensional mountings. Wiring - It utilizes a /5 HP motor to turn 573 RPM and move 2475 CFM. ACHAF20A4

4 Air Distribution System The unique Fan-Jet is a special tube pressurizing fan with curved stationary discharge vanes (stator vanes) that recover the rotational energy of discharging air to increase performance capacity and efficiency. Low-cost: Fan-jet powers more air at less horsepower for best results at low operating costs. Quality: Fan-jet is fully assembled at factory, test ran and inspected and then shipped ready to install with brackets and fasteners. High Performance Propellers: The propellers are matched to the size, performance and construction of the Fan-Jet. RC fan propellers are welded steel with the two coat finish. RCA fan propellers are welded heavy gauge aluminum. Built Tough: The steel model RC is available in 8", and 30" sizes and is rust protected with a metal wash process and two-coat, baked on finish. Heat kits allow use of gas fired, electric, steam or hot water unit heaters without outside air passing through the heat exchanger. When used with a Fan-jet, Heat kits keep coils and elements out of the air flow route, thus saving energy. Each kit consist of two baffle plates with air scoops attached horizontally to the top and bottom of the Fan-jet Unit and to the framed opening of the motorized inlet shutter. Kits also come with a Fan-jet motor shield to prevent heat build-up. A center baffle accessory is included for use when opposing heaters trigger separately, preventing blow-through of hot air and possible motor damage. Fan-Jet with Heat Kit (Heater sold Separately) Polyethylene Tubing All tubes are engineered for uniform distribution and proper mixing of air to produce the best aerodynamic effect in greenhouse structures. Furnished in clear 4 mil thick UV stabilized polyethylene material Each tube is custom punched to match the selected Fan-jet unit with each specific house HANGER SPACING AC2TUBE AC8TUBE AC24TUBE AC30TUBE 2" Diameter 8" Diameter Diameter 30" Diameter NOTE: Tubing must be punched specifically for diameter and length of run. When ordering, please specify length of run. Since tubes are custom punched, orders already processed or shipped cannot be cancelled or returned for credit. Tube Hanger Set & Wire Support Kit Unique hanger clamps onto tubing for easy attachment to overhead support wire with snap ring. Wire support kits available in 50', 00', and 50' lengths. Kits include six strand 0 gauge wire, turnbuckle and two securing clips. When ordering support kit please specify length. 0' 0' 8' 6' AHANGSET0 ATSUP50 ATSUP00 ATSUP50 Hangers 0/pkg 50 support kit 00 support kit 50 support kit

5 Water Distribution & Return System The 4 aluminum system utilizes quick snap together components for easy installation using a minimum of hardware. The heavy extruded gutter and support are designed to support the pads and carry the water back to the sump. The aluminum top cover is made in two pieces to facilitate cleaning the PVC pipe if clogged. The 6 system is available in Stainless Steel Only. The basic system includes Pipe Distributors, Pad Covers, Return Gutters, and necessary connectors and fittings. Sold in 5' increments. Please Call cassco For Current Pricing 4" and 6" KOOL-CEL Pads Kool-Cel pads are cellulose cooling cells 4" and 6" deep, 2" wide and available in 2" increments from to 72" tall with two pieces of 4" combined to make 84" and 96" tall pads. The cooling cells are made from a specially formulated cellulose paper impregnated with insoluble antirot salts. The exclusive cross fluted design makes Kool-Cel Pads a strong self supporting pad with high evaporative efficiency. SIZE SIZE ACKC424 ACKC436 ACKC448 ACKC460 ACKC472 4" x 4" x 4" x 48" 4" x 60" 4" x 72" ACKC624 ACKC636 ACKC648 ACKC660 ACKC672 6" x 6" x 6" x 48" 6" x 60" 6" x 72" MI-T-Edg - Optional coating on one or both sides of the pads reduces algae growth and enables easy pad cleaning and maintenance. Call for Prices. Pumps Submersible pumps with cast iron housing, polypropylene base and polycarbonate cover. They include a lifetime oil supply and non-clog pumping head and impeller. AC5SPUMP AC30SPUMP AC70SPUMP HP /4 /2 SYSTEM LENGTH (MAX.) 4" 6" Plumping Package The plumbing package is designed for use with all the pumps for the Kool-Cel systems and includes the necessary plumbing fittings and valve to complete the installation from the sump to the distributor and also contains the water strainer and float valve ACPLUMBKIT NOTE: The sump tank, cover and tank fittings are furnished by others and should be sized to provide gallon per square foot of 4" pad area and gallon per square foot of 6" pad area.

6 ADP is the only HVAC manufacturer of evaporator coils, air handlers, and unit heaters that give you more: more innovative products for a wide range of applications, more user-friendly designs for faster, easier installation, and more attention to what you need. ADP prides itself on being an advanced solution provider of quality, innovative products and services to our customers. Their commitment to excellence has made them a trusted partner to contractors, distributors and engineers who require excellent reliability and performance. ADP also has some state of the art features to help keeping crops comfortable easier. Features and Benefits: Dependable Performance In shot assembly is easy to clean and will not rust like ribbon-type burners. Direct-spark ignition lights the burners directly, eliminating pilot outages. Tubular heat exchanger eliminates metal stresses and cracking that can occur in clamshell heat exchangers. Heavy-gauge prepainted cabinet maintains its appearance for years to come. Aluminized heat exchanger is available for economical heating. Stainless steel heat exchanger is optional for corrosive environments. Easy Installation and Maintenance Natural gas or LP available. Power venter allows horizontal or vertical venting flexibility. Low-voltage terminal strip simplifies wiring. Self-diagnostic board with indicator light makes troubleshooting simple. Diagnostic board automatically retries ignition after one-hour lockout. Warranty: 2-year warranty on parts. 0-year warranty on aluminized heat exchanger. 5-year warranty on stainless heat exchanger. MODEL # INPUT WT. SEP5 SEP45 SEP75 SEP200 SEP230 5,000 BTUH 45,000 BTUH 75,000 BTUH 95,000 BTUH 230,000 BTUH 40 lb. 50 lb. 65 lb. 65 lb. 270 lb. ADPS5A ADPS45A ADPS75A ADPS200A ADPS230A CONTROLS T5 Thermostat The T5 thermostat is a rugged, weather resistant, durable control for both heating and cooling (ventilation) in agricultural, industrial, and commercial environments. Large, readily visible dial has a range of degree temperature range. TF5 Thermostat

7 GREENHOUSE SHADING Liquid Shade Kool Ray was the first on the market and it is still the most beneficial, labor saving, and cost effective liquid shade out there. For use on commercial greenhouses, apply over the roof of the greenhouse and is designed to lower the inside greenhouse temperature during the warmer spring summer growing seasons. Kool Ray Ultra X-tra Stick The newest development in liquid shade, Kool Ray Ultra is a super concentrated formula that works on glass as well as plastics. gallon of Ultra is equal to 2 gallons of regular Kool Ray. CPKRUW CPKRUW5 CPKRUG CPKRUG5 White, gallon White, 5 gallons Green, gallon Green, 5 gallons For use with Kool Ray Ultra, X-tra is an adhesive promoter that will increase hold, wear, and overall life of shade. Primarily for use with glass, but should be used with caution on plastics because of slight removal problems. For more protection, add something X-tra. CPXSTIK CPXSTIKQ Gallon of adhesive Quart of adhesive A strong, durable woven polypropylene fabric. Shade cloth will last many years when properly handled and stored. This propylene material only shrinks approximately %, which makes tight installation possible. ACTUAL SHADE STANDARD WIDTHS SHADE30 SHADE47 SHADE55 SHADE63 SHADE73 SHADE80 30% 47% 55% 63% 73% 80% 0, 2 6, 0, 2, 5 6, 0, 2, 5 6, 0, 2, 5 6, 0, 2, 5 6, 0, 2, 5 Note: DUE TO MANUFACTURING AND SHIPPING INVOLVED, PLEASE PLACE YOUR ORDERS WELL IN ADVANCE OF YOUR NEEDS. Shade cloth is custom made to specification requiring an average of 4-8 weeks notice time during the spring and summer months. Because this is a custom item, once the order is in production, it is not cancelable, returnable, or refundable. When ordering, please specify, length, width, percentage of shade, edge finishing (sewn, hemmed, or taped) and grommet spacing. Whenever possible, order width in multiples or a combination of standard widths. AN ADDITIONAL CHARGE OF $5.00 APPLIES TO PIECES LESS THAN 30 SQUARE FEET.