Astro. FF-14 Friction Feeder. Operator Manual
|
|
- Nelson Norman
- 5 years ago
- Views:
Transcription
1 Astro FF-14 Friction Feeder Operator Manual
2 SAFETY PRECAUTIONS THIS EQUIPMENT PRESENTS NO PROBLEM WHEN USED PROPERLY. OBSERVE SAFETY RULES WHEN OPERATING FF-14 FRICTION FEEDER. BEFORE USING FF-14, READ THIS MANUAL CAREFULLY AND FOLLOW RECOMMENDED PROCEDURES, SAFETY WARNINGS, AND INSTRUCTIONS: Keep hands, hair, and clothing clear of rollers and other moving parts. Avoid touching moving parts or materials while the machine is in use. Before clearing a jam, be sure machine mechanisms come to a stop. Always turn machine OFF before making adjustments, cleaning machine, or performing any maintenance covered in this manual. Use power cord supplied with machine. Plug it into a properly grounded, easily accessible wall outlet located near machine. Failure to properly ground machine can result in severe personal injury and/or fire. Power cord and wall plug are primary means of disconnecting machine from power supply. DO NOT use an adapter plug on line cord or wall outlet. DO NOT remove ground pin from line cord. DO NOT route the power cord over sharp edges or trap it between furniture. Avoid using wall outlets controlled by wall switches, or shared with other equipment. Make sure there is no strain on power cord caused by jamming it between equipment, walls or furniture. DO NOT remove covers. Covers enclose hazardous parts that should be accessed by a qualified service representative. Report any cover damage to your service representative. This machine requires periodic maintenance. Contact your authorized service representative for required service schedules. To prevent overheating, do not cover vent openings. Use this equipment only for its intended purpose. In addition, follow any specific occupational safety and health standards for your workplace or area. This manual is intended solely for the use and information of Astro Machine Corp. its designated agents, customers, and their employees. The information in this guide was obtained from several different sources that are deemed reliable by all industry standards. To the best of our knowledge, that information is accurate in all respects. However, neither Astro Machine Corp. nor any of its agents or employees shall be responsible for any inaccuracies contained herein. All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or any information storage and retrieval system, without permission in writing from the publisher.
3 Table of Contents Feeder Setup and Operating Instructions 4 Contents of Packaging 4 Assembly and Installation 4 Getting Acquainted Control Panel 5 Front Panel 5 Set-up and Operation 6 Maintenance 9 Cleaning Sensors 9 INDEX 10
4 Feeder Setup and Operating Instructions FF-14 Feeder is designed to feed material from single sheets up to 3/8" in thickness. Material size can vary from 2" long by 3" wide up to 15" long by 14" wide. It is ideal for feeding into conveyor transport systems, folding and stitching machines, packaging and inkjet applications. Feeds up to 40,000 pieces per hour (depending on size and material). Contents of Packaging 1. FF-14 Friction Feeder 2. Right and Left Media Guides, Rear Media Guide 3. Metering Segments (Sheet Separators) Bag of 4 4. Feeder Base (to align Feeder with other inline components) 5. AC Power Cord 6. Operator Manual Assembly and Installation Unpack Feeder. Install two Side Guides using four screws [A] supplied (two on each side). Place Feeder on a flat, level surface. Plug Feeder into a properly grounded receptacle. To permanently mount Feeder: Remove four rubber feet. NOTE: Two FF-14 Feeder versions: FF-14 operates on 115 VAC FF-14E operates on 220 VAC. NOTE: Place Feeder on the Feeder Base to align it with other inline components such as Printers and Tabbers. Exit end of Feeder faces closed end of Base. Feeder's rubber feet fit into recesses on top of Base [B].
5 Getting Acquainted Control Panel 1 SPEED CONTROL Varies speed of Feeder in either MANUAL or AUTO modes to provide separation between printed pieces. 2 CONTINUOUS FEED Press with Feed Select Switch in MANUAL position to allow Feeder to feed continuously. 3 SINGLE FEED Press this switch with Feed Select Switch in MANUAL position to make the Feeder to feed a single piece of media. 4 BATCH COUNTER Resettable. Counts number of pieces run on each job. 5 FEED SELECT SWITCH When set to MANUAL, operator can feed one or continuous pieces of media by pressing FEED switches. When in AUTO, interface controls Feeder through an external device. Front Panel 1 POWER RECEPTACLE Power cord plugs in here. Make sure that power cord is only plugged into a properly grounded receptacle. 2 ON/OFF SWITCH Controls power to Feeder. 3 FUSE HOLDER Fuse protects Feeder's electronics and motor. 4 INTERFACE CONNECTOR Can be used to control Feeder feeding. (See Interface Connection for more information.)
6 Set-up and Operation 1. Release Separator Locking Lever, raise Separators and lock in position (as shown). 2. Place media under Separators, then release Separator so they rest on media. Lock Separators in position using Locking Lever. 3. Adjust Side Guides to within 1/32" of media. Then adjust Rear Guide so media is raised approximately 1/2". (For heavy, thick, media this may not be required.)
7 4. Adjust Exit Roller pressure by pushing in on Pressure Control Lock Button [A] and raising or lowering Adjusting Lever [B]. For plain paper or envelopes, Lever should be in the down position. For thicker material, Lever should be adjusted so media feeds without any bounce in the Exit Roller Assembly. 5. Turn Feeder ON and feed one piece with Speed Control set to low speed (1 or 2). Stop Feeder with piece halfway through the exit. Then adjust Feed Sensor so that it is pointed directly at the piece as it exits Feeder. Sensor prevents double feeding in case of a jam or stoppage. 6. Turn Feeder power switch ON. Set AUTO/MANUAL switch to MANUAL. Press SINGLE feed button for single sheet feeding or CONTINUOUS feed button for continuous feeding. 7. INTERFACE CONNECTION. FF-14 Feeder can also be controlled remotely: To have Feeder start feeding from a remote signal, signal must be wired through INTERFACE connector on Feeder. AUTO/MANUAL switch must be set to AUTO. Below is a wiring diagram of the Interface Connector and the switching circuitry that accomplishes this. Signal can come from a closed contact of a relay.
8 WARNING! WIRING FF-14 FEEDER FOR AUTOMATIC OPERATION SHOULD ONLY BE DONE BY A TECHNICIAN COMPETENT IN ELECTRONIC INSTALLATIONS.
9 Maintenance WARNING! FEEDER IS A PRECISION MACHINE THAT SHOULD BE CLEANED REGULARLY TO INSURE MANY YEARS OF SERVICE. BEFORE PERFORMING ANY MAINTENANCE, DISCONNECT FEEDER FROM ITS POWER SOURCE! Feeder must be cleaned regularly of accumulated paper dust and ink. Depending on types of media that are run, paper dust may accumulate within Printer and on Transport. Always unplug it from power receptacle and remove covers. Internal areas: Best cleaned with a vacuum with a soft brush attachment to help loosen dust particles. Take care not to damage PC Boards or electrical wiring. Exterior areas: May be cleaned with any standard nonabrasive household cleaner. Cleaning Sensors CAUTION NEVER SPRAY OR POUR CLEANERS DIRECTLY ON OR INTO FEEDER. EXCESS LIQUID COULD HARM ELECTRONIC PARTS. ALWAYS DAMPEN A RAG WITH CLEANER AND APPLY IT TO PARTS TO BE CLEANED. Keep two Sensors on Feeder clean. Media Sensor [A] is located under Exit Guide Rollers (as shown). Jam Sensor [B] is located on Jam Sensor Support. Use a Q-tip to clean Sensors. CAUTION DO NOT USE SOLVENTS OR ABRASIVES TO CLEAN SENSORS.
10 INDEX A Auto/Manual Mode... 5 B Batch Counter... 5 C Continuous Feed Switch... 5 Control Panel... 5 Batch Counter... 5 Continuous Feed Switch... 5 Feed Select Switch... 5 Single Feed Switch... 5 Speed Control... 5 F Feed Select Switch... 5 Feeder Assembly... 4 Control Panel... 5 Fuse Holder... 5 Install... 4 Interface Connector... 5 Maintenance... 9 Operation... 6 Power Receptacle... 5 Power Switch... 5 Set-Up... 4 Fuse Holder... 5 I Install Feeder... 4 Interface Connector... 5 M Maintenance... 9 O ON/OFF Switch... 5 Operation... 6 P Package Contents... 4 Power Receptacle... 5 Power Switch... 5 S Sensors, Cleaning... 9 Set-Up Feeder... 4 Single Feed Switch... 5 Speed Control... 5
11
12 Copyright 2017 Astro Machine Corp. 01/31/2017 Part Number: 200-FF14N Rev D
ASTRO FF14 FRICTION FEEDER SERVICE MANUAL
ASTRO FF14 FRICTION FEEDER SERVICE MANUAL Astro Machine Corp. 630 Lively Blvd. Elk Grove Village, IL 60007 Phone: (847) 364-6363 Fax: (847) 364-9898 www.astromachine.com SAFETY PRECAUTIONS THIS EQUIPMENT
More informationEASY FEED LITE FRICTION FEEDER OPERATOR MANUAL. Rev
EASY FEED LITE FRICTION FEEDER OPERATOR MANUAL Rev 02-04-13 SAFETY PRECAUTIONS THIS EQUIPMENT PRESENTS NO PROBLEM WHEN USED PROPERLY. OBSERVE THE FOLLOWING SAFETY RULES WHEN OPERATING THE RENA EASY FEED
More informationTA-12/HT12 Tabber. OPERATING GUIDE Revised:
TA-12/HT12 Tabber OPERATING GUIDE Revised: 2-27-13 Neopost USA would like to Thank You for investing in our quality built products. Please record the following information for future reference: Model:
More informationTA-12. Tabbing System USER'S GUIDE
TA-12 Tabbing System USER'S GUIDE SAFETY PRECAUTIONS THIS EQUIPMENT PRESENTS NO PROBLEM WHEN USED PROPERLY. HOWEVER, CERTAIN SAFETY RULES SHOULD BE OBSERVED WHEN OPERATING THE TA12 TABBER. BEFORE USING
More informationTB-390 Conveyor Stacker
TB-390 Conveyor Stacker OPERATIONS MANUAL Revised: 7-30-14 RENA Systems Inc. would like to Thank You for investing in our quality built products. Please record the following information for future reference:
More informationFD 2052 AutoSeal 12/2007 OPERATOR MANUAL FOURTH EDITION
FD 2052 AutoSeal 12/2007 OPERATOR MANUAL FOURTH EDITION TABLE OF CONTENTS DESCRIPTION 1 SPECIFICATIONS 1 UNPACKING AND SET-UP 1-2 CONTROLS 2 OPERATION 3 CUSTOM FOLDS 3-4 Measuring Fold Lengths 3 Custom
More informationASTRO ENVELOPE FEEDER AMC FOR HEIDELBERG PRINTMASTER INSTALLATION AND OPERATING INSTRUCTIONS
ASTRO ENVELOPE FEEDER AMC-2000-17 FOR HEIDELBERG PRINTMASTER INSTALLATION AND OPERATING INSTRUCTIONS INTRODUCTION Thank you for purchasing the Astro Envelope Feeder. It is fast, efficient, reliable, and
More informationXPS-ProDry User s Guide Dryer Base
XPS-ProDry User s Guide XPS-ProDry User s Guide Dryer Base For Use with Inkjet Imaging Systems Manual Part#: M-3120 Revision: August 2005 XPS-ProDry User s Guide Written by Frank Mauri & John Brand Published
More information4 Printer Maintenance
4 Printer Maintenance Overview This chapter discusses the following: Cleaning the Printer and Accessories Preventative Maintenance Overview 4-1 Cleaning the Printer and Accessories To maintain high print
More informationCAUTION. Machine: SHRINK LABEL AUTOMATIC APLICATOR. Model: SLEEVEPRO 450AB. Input Voltage: 400 VAC, 3PH, 50Hz. Contact:
CAUTION Read carefully all the instructions of this manual before start any operation on this machine. Do not put your hands close to any moving part of the machine. Do not make any adjustment when the
More informationModel 5060/5070. Letter Opener Revision 3 Brush Transport
Model 5060/5070 Letter Opener Revision 3 Brush Transport ON/OFF, Reset Envelope Guide Ramp / Envelope Model 5060, 5070 Letter Opener Introduction Variable Speed Track Cover Counter (Optional) Deflector
More informationFood Slicer Visit our website at:
Electric Food Slicer 42787 Set up And Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury.
More informationTECHNICAL DATA IMPORTANT SAFETY NOTES
IMPORTANT SAFETY NOTES Turn off and unplug the shredder before moving, emptying the waste bin, or if the shredder will not be used for a long period of time. Keep children and pets away from shredder.
More informationFD 430 Envelope Sealer
FD 430 Envelope Sealer 1/2018 OPERATOR, MAINTENANCE, & PARTS MANUAL REV. 1 2 CONTENTS 1 SAFETY INSTRUCTIONS... 5 1.1 Symbols and reference key... 5 1.2 Basic safety precautions... 6 1.3 Safety advice...
More informationFD 90 / FD 95 Rotary Perforators
FD 90 / FD 95 Rotary Perforators 11/2018 OPERATOR MANUAL SECOND EDITION TABLE OF CONTENTS SPECIFICATIONS 1 SAFETY PRECAUTIONS 1 DESCRIPTION 2 INSTALLATION AND OPERATION 3 INFEED TABLE ADJUSTMENT 3 OUTFEED
More informationASG EZ-9000GR Tape Dispenser User Manual ASG #66136
ASG EZ-9000GR Tape Dispenser ASG #66136 Revision Date: 03/27/18 1 Read Before Use Warnings and Cautions The safety guidelines in this instruction manual must be observed in order to prevent injury to the
More informationKF-250 Knife Folding Machine
KF-250 Knife Folding Machine Serial Number Date Page left blank intentionally 2 Table of Contents INTRODUCTION... 5 PREFACE... 5 SPECIFICATIONS... 5 ELECTRICAL SPECIFICATIONS... 6 SAFETY PROCEDURES...
More informationUser Guide. Portable banknote counter AB300
User Guide Portable banknote counter AB300 Thank you for purchasing this AccuBANKER product. We recommend reading all information in the user guide to become familiar with this product. AccuBANKER and
More informationIreland. Australia. New Zealand
UK Ireland Australia New Zealand 2 3 4 5 Intended use Your Black & Decker vacuum cleaner has been designed to vacuum dry substances. This product is intended for household use only. Safety instructions
More informationAuto Opening with Pressure Readout 15 x15 & 16 x20 Heat Transfer Machines
S-450P & S-650P Auto Opening with Pressure Readout 15 x15 & 16 x20 Heat Transfer Machines OWNER S MANUAL S-650P shown For Customer Service, Call 1-800-835-0606 or Visit www.hixcorp.com CONTENTS Receiving
More informationCOOL TOUCH ELECTRIC WATER KETTLE
COOL TOUCH ELECTRIC WATER KETTLE MODEL:SWK-1701DB USER INSTRUCTIONS Seamless Stainless Steel Interior-Healthy Water Cool Touch Exterior-Safe To Use www.thesecura.com Welcome Congratulations on purchasing
More informationS-1200 Series Currency Counter Operating Manual. Models S-1200, S-1215 and S-1225
S-1200 Series Currency Counter Operating Manual Models S-1200, S-1215 and S-1225 CONTENTS Introduction 1 Front View Machine Diagram 2 Rear View Machine Diagram 3 Control Panel Overview 4 Control Panel
More informationIreland. Australia. New Zealand
UK Ireland Australia New Zealand 2 3 4 5 Intended use Your Black & Decker vacuum cleaner has been designed to vacuum dry substances. This product is intended for household use only. Safety instructions
More informationD14 & D18 Upright Vacuum
Operator's Manual D14 & D18 Upright Vacuum READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting
More information457LAVEXDM15 DUAL MOTOR HEPA UPRIGHT VACUUM CLEANER
457LAVEXDM15 DUAL MOTOR HEPA UPRIGHT VACUUM CLEANER IMPORTANT SAFEGUARDS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS
More informationGallery Electric Fireplaces
Gallery Electric Fireplaces Homeowner s Installation Instructions & Operating Manual Model: GE-50, GE-58, GE-70, GE-78 GE-94 FOR YOUR SAFETY SERVICE MUST BE PERFORMED BY A QUALIFIED SERVICE AGENCY. DO
More informationTHERMO POT MODEL: ETP-D4013(WH)/ ETP-D5013(WH)/ ETP-D6013(WH) Owner s Manual. Please read this manual carefully before operating your set.
THERMO POT MODEL: ETP-D4013(WH)/ Owner s Manual ETP-D5013(WH)/ ETP-D6013(WH) Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial
More information2 000W CYCLONIC BAGLESS VACUUM
2 000W CYCLONIC BAGLESS VACUUM /GVAVK08 Instruction Manual Contents Guide to the Appliance Caring for the Environment Safety Information and Warnings Basic Set Up Care and Maintenance Troubleshooting 2
More informationTECHNICAL DATA. Continuous run time
IMPORTANT SAFETY NOTES Turn off and unplug the shredder before moving, emptying the waste bin, or if the shredder will not be used for a long period of time. Keep children and pets away from shredder.
More informationKONICA MINOLTA GP-502 OPERATION MANUAL
KONICA MINOLTA GP-502 OPERATION MANUAL Rev 1.0 February 2012 Table of Contents 1. Safety 2. Overview 2.1 Features & Benefits of GP-502 2.2 Ellipse Binding Elements 2.3 User Interface & Feature Locations
More informationTHERMO POT MODEL: ETP-C3211(WH) Owner s Manual. Please read this manual carefully before operating your set. Retain it for future reference.
THERMO POT MODEL: ETP-C3211(WH) Owner s Manual Please read this manual carefully before operating your set. 1 Retain it for future reference. Record model number and serial number of the set. See the label
More informationManual Feed Slot Opening. Wastebin. Credit Card Casters
Model# AF300 Contents Product Diagram & Technical Specifications... 3 Warnings... 4 Installation / Safety Instructions... 5 Assembly... 6 Operation... 6-8 Care & Maintenance... 8 Troubleshooting... 9 Warranty,
More informationCleaning (Preventative Maintenance) on the magicolor 2400 Series
Cleaning (Preventative Maintenance) on the magicolor 2400 Series Read all caution and warning labels carefully, making sure to follow any instructions contained in them. These labels are located on the
More informationEK14 / EK14C Premium Electric Kit
EK14 / EK14C Premium Electric Kit IMPORTANT SAFETY INSTRUCTIONS Please read all instructions before using the Electric Powerhead. When using this electrical appliance, basic precautions should always be
More informationG-10f/GCG-10f UPRIGHT COOLER
G-Series Cooler G-10f/GCG-10f UPRIGHT COOLER Manual is for the following models: G-10F, G-10-F33EB GCG-10F, GCG-10-F33EB GCG-10F2, GCG-10-F233EB G-10-F33EB-HC, GCG-10-F33EB-HC GCG-10-F233EB-HC Instruction
More informationGCG-9. Instruction Manual. G-Series Cooler. Manual is for the following models: GCG-9-N13EB G-9-N13EB GCG-9-B13EB UPRIGHT COOLER
G-Series Cooler UPRIGHT COOLER Manual is for the following models: -N13EB G-9-N13EB -B13EB Instruction Manual FOR YOUR FUTURE REFERENCE This easy-to-use manual will guide you in getting the best use of
More informationINSTRUCTIONS FOR USE OF FLOUR RECEPTACLE (Mills are shipped with either receiver bag or canister-not both)
Subject: A-33 Instructions Adjustment instructions for the A-33X and Jiffy flour mill. Disregard adjustment steps 1 through 6 on page 2. The mill is adjusted from a fine to a coarse grind by moving the
More information1500W CERAMIC HEATER. Instruction Manual
1500W CERAMIC HEATER GVACH110 Instruction Manual Contents Guide to the Appliance 2 Caring for the Environment 3 Safety Information and Warnings 4 Operation Instructions 5 Care and Maintenance 6 Technical
More informationJUNEAU JUN. 08/51193/0 Issue 0
JUNEAU JUN 08/51193/0 Issue 0 The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3 These cover
More informationEP-21F Manual Letter Folder Operation Manual
EP-21F Manual Letter Folder Operation Manual EP Equipment Co.,Ltd. Introduction Thank you for selecting EP folder. This machine is designed for efficiently folding paper up to legal size (216 356mm). To
More informationGeneral Care and Safety Guide
General Care and Safety Guide Thank you for choosing a Celsius Ceramic Tower Heater. This Celsius appliance has been designed and manufactured to high standards of engineering and with proper use and care,
More informationUSER S GUIDE. ecal lite Software Access Code included! SUBSECTION. Read Guide Before Operating Product. Save Guide For Reference.
USER S GUIDE SUBSECTION ecal lite Software Access Code included! Read Guide Before Operating Product. Save Guide For Reference. IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS READ THESE IMPORTANT
More informationIntroduction... 3 Setup & Suggestions... 4 Basic Use... 4 Setting Time... 4 Setting Temperature... 5 Setting Height / Pressure...
Table of of Contents Contents... 2 Introduction... 3 Setup & Suggestions... 4 Basic Use... 4 Setting Time... 4 Setting Temperature... 5 Setting Height / Pressure... 6 Aligning the pedestal... 6 Guidelines
More informationHomeowner s Installation Instructions & Operating Manual
Wall Mounted Electric Fireplace Homeowner s Installation Instructions & Operating Manual Model: EF68-72 Series Used With Listed Front Facia Only: MT68-72 FOR YOUR SAFETY SERVICE MUST BE PERFORMED BY A
More information1/2011 V1. Puzer AINO USER MANUAL. Read this instruction before using the vacuum cleaner! Keep the instructions near the vacuum cleaner for later use!
Puzer AINO USER MANUAL Read this instruction before using the vacuum cleaner! Keep the instructions near the vacuum cleaner for later use! 1 Vacuum cleaner parts 1 Part numbers 1. Wall inlet 2. Display
More informationWall Mount Electric Fire Place with Remote Control
INSTALLATION AND USER INSTRUCTION GUIDE Wall Mount Electric Fire Place with Remote Control Model: 67500 Mahogany Effect Model: 67501 Beveled Mirror READ AND SAVE THESE INSTRUCTIONS Carefully read and review
More informationOPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS FOR CARPET PRO UPRIGHT VACUUMS MODELS : CPU-75, CPU-75T, CPU-85, CPU-85T Before operating the vacuum, please read these instructions completely. Index Important Safety Instructions.............................................................2
More informationINSTRUCTIONS AND WARRANTY
INSTRUCTIONS AND WARRANTY MODEL NO. SFH 804 DESCRIPTION: Salton Versatile Fan Heater Congratulations on purchasing our Salton Versatile Fan Heater. Each unit is manufactured to ensure safety and reliability.
More informationSecurity. Throat: Maximum Capacity: Shred Bin Capacity: Voltage: Level: Weight: -Unpack. Oil your. diminished. cleaners 4. 5.
IMPORTANT SAFETY NOTES TECHNICAL DATA Turn off and unplug the shredder before moving, emptying the waste bin, or if the shredder will not be used for a long period of time. Keep children and pets away
More informationUltra Lightweight Household & Commercial Vacuums
Owner s Manual Ultra Lightweight Household & Commercial Vacuums Save These Instructions Index Important Safety Instructions............................................................. 2 Polarization Instructions................................................................
More informationIMPORTANT SAFETY INSTRUCTIONS
User Manual INDEX IMPORTANT SAFETY INSTRUCTIONS... 1 FEATURES... 2 SPECIFICATIONS...2 PRODUCT DESCRIPTION... 3 THE CONTROL PANEL... 4 UNIT SETUP... 5 TO OPERATE SAFELY... 5 OPERATING INSTRUCTIONS... 6-10
More informationCyclonic Vacuum Cleaner XS701 SERIES USER GUIDE
Cyclonic Vacuum Cleaner XS701 SERIES USER GUIDE IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE When using this electrical appliance, basic precautions should always be followed,
More informationUser Guide Digital Bill Counter AB4000
User Guide Digital Bill Counter AB4000 Warning Before turning the power on, please make sure there are no objects obstructing the operation of the rollers and wheels. Operate the machine only under normal
More informationDC200 Digital Dispenser Operating Manual
DC200 Digital Dispenser Operating Manual 2015 Fisnar Phone: (973) 646-5044 E-mail: info@fisnar.com Table of Contents Product Safety Statements 4 Specifications 6 Accessories 6 External Controls 7 Machine
More informationTACH-IT MODEL #3568 SEMI-AUTOMATIC TWIST TIE MACHINE OPERATION MANUAL AND PARTS LIST
TACH-IT MODEL #3568 SEMI-AUTOMATIC TWIST TIE MACHINE OPERATION MANUAL AND PARTS LIST 1 TABLE OF CONTENTS: SECTION 1 CAUTION PAGE 3 SECTION 2 PARTS IDENTIFICATION PAGE 4 SECTION 3 MACHINE DIMENSIONS AND
More informationAUSTRALIA PAD1200-XE NEW ZEALAND
PAD1200-XE AUSTRALIA NEW ZEALAND 11 9 10 10 11 A B 12 13 C D 15 14 16 17 F 2 ENGLISH ENGLISH Intended use Your Black & Decker Dustbuster auto car vacuum cleaner has been designed for light dry vacuum cleaning
More informationTurbo Circulating Fan (DC)
Instruction Manual Turbo Circulating Fan (DC) Model: HTCFDC READ AND SAVE THESE INSTRUCTIONS Please read and follow the instructions in this user manual even if you feel you are familiar with the product,
More informationHomeowner s Installation Instructions & Operating Manual
Homeowner s Installation Instructions & Operating Manual ELECTRIC HEATER WITH REMOTE CONTROL Model: GI-32-ZC IS-36-ZC, IS-42-ZC Insert surrounds READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING
More information10L Evaporative Cooler with Timer
10L Evaporative Cooler with Timer / GVAEC10 Instruction Manual 1 Important Safety Instructions Thank you for choosing this GVA product. This GVA appliance has been designed and manufactured to high standards
More informationOwner s Manual MODEL: SCT-1. Before operating the vacuum, please read these instructions completely.
Owner s Manual MODEL: SCT-1 Before operating the vacuum, please read these instructions completely. IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be
More information1217A Operating Instructions
1217A Operating Instructions Reversible Motor Friction Fed Conveyor Stacker Easy Disassembly Adjustable Folds Counter Available MADE IN USA SPECIFICATIONS Paper Weight.28 Lbs. Bond, 90Lbs. Cover, 135Lbs.
More informationModel S-530 Coin Sorter / Value Counter Operating Manual
Model S-530 Coin Sorter / Value Counter Operating Manual Table of Contents Using the Product Safely... 2 About the Warning Stickers and Points of Warning/... 2 Warnings... 3 s 4 Names of the Machine Parts....
More informationRice Cooker. Instruction manual. Model: CB944-A
Rice Cooker Instruction manual Model: CB944-A AU Telephone Helpline: 1300225960 Safety Tips Position on a flat, stable surface. A service agent/qualified technician should carry out installation and any
More informationUSERS MANUAL. Desiccant Dehumidifier. Model: ECO DD322FW CLASSIC
keeping your home safe and clean USERS MANUAL Desiccant Dehumidifier Model: ECO DD322FW CLASSIC Read This Manual Inside you will find many helpful hints on how to use and maintain your dehumidifier properly
More information45 Wide Format Hot and Cold Laminator
45 Wide Format Hot and Cold Laminator 1 IMPORTANT SAFEGUARDS OPERATING INSTRUCTIONS TCC1200 When using electrical machines, basic precautions should always be followed to reduce the risk of electric shock
More informationHT-600D. (either domestic or foreign), please keep a copy of their sales invoice showing the serial
WARRANTY (Effective January 1, 2007) HIX will automatically register the equipment on the date it was shipped to you or your distributor. If the equipment was not purchased directly from HIX, but through
More informationπ H-7147 SANITAIRE EON QUIET CLEAN VACUUM SAFETY uline.com
π H-7147 SANITAIRE EON QUIET CLEAN VACUUM 1-800-295-5510 uline.com SAFETY PAGE 1 OF 9 NOTE: When using an electrical appliance, basic precautions should always be followed, including the following: READ
More informationSECAP Conveyor TC72 / Dryer TD72
SECAP Conveyor TC72 / Dryer TD72 4/08 Assembly, Operation & Parts Manual Second Edition TABLE OF CONTENTS SPECIFICATIONS UNPACKING ASSEMBLY 2 SETUP & OPERATION ELECTRICAL SCHEMATIC 8 CONVEYOR PARTS 9 OPTIONAL
More informationBQ-260/260L. Important Information BOOK BINDER
BOOK BINDER BQ-260/260L Important Information - This manual is designed to help you to install, operate and maintain Perfect Binder BQ- 260/260L. Read, understand and keep this manual in a safe and convenient
More informationGeneral Care and Safety Guide
General Care and Safety Guide Thank you for choosing a Celsius Convection Panel Heater. This Celsius appliance has been designed and manufactured to high standards of engineering and with proper use and
More informationInstruction Manual. Cheddar Easy All-In-One Cheese Corn Shop
Instruction Manual Cheddar Easy All-In-One Cheese Corn Shop Model No. 2703-00-000 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA 2017 Gold Medal Products Co. Part No. 110028 SAFETY PRECAUTIONS
More informationPANEL HEATER OPERATING INSTRUCTIONS. For Models: TWFP10000, TWFP PK
PANEL HEATER OPERATING INSTRUCTIONS For Models: TWFP10000, TWFP10000-2PK This page is intentionally left blank General Care and Safety Guide Thank you for choosing a Living & Co Panel Heater. This Living
More informationRVAC-100 VACUUM CLEANER MANUAL. For Household Use Only
VACUUM CLEANER MANUAL RVAC-100 For Household Use Only 790 Rowntree Dairy Road, Woodbridge, ON Canada L4L 5V3 t: 905.851.6701 f: 905-851.8376 e: info@reversomatic.com Toll Free: 1.800.810.3473 (Canada)
More informationSOUTHERN ENTERPRISES INC.
SOUTHERN ENTERPRISES INC. RELAX If you can follow a few easy, step-by-step directions In order.you CAN ASSEMBLE THIS ITEM. STYLE NO.:FA514500TX ELECTRIC FIREBOX INSERT USER S OPERATING MANUAL CONSUMER
More informationINSTALLATION & USER INSTRUCTIONS
INSTALLATION & USER INSTRUCTIONS LED ELECTRIC FIRE Focal Point Fires plc. Christchurch, Dorset BH23 2BT Tel: 01202 499330 Fax: 01202 499326 www.focalpointfires.co.uk e : sales@focalpointfires.co.uk MODELS
More informationGDDEM10 DEHUMIDIFIER
GDDEM10 DEHUMIDIFIER SOCIABLE REMARK When using this dehumidifier in the European countries, the following information must be followed: DISPOSAL: Do not dispose this product as unsorted municipal waste.
More informationSAFETY, OPERATION AND MAINTENANCE MANUAL. DRY VACUUM CLEANER This unit is intended for commercial use. SAVE THESE INSTRUCTIONS
SAFETY, OPERATION AND MAINTENANCE MANUAL W/ PARTS LIST DRY VACUUM CLEANER This unit is intended for commercial use. READ & FOLLOW ALL INSTRUCTIONS,WARNINGS & CAUTIONS BEFORE USING THIS VACUUM This vacuum
More informationInstruction Manual. Double Candy Apple Cooker
Instruction Manual Double Candy Apple Cooker Model No. 4416 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA 2014 Gold Medal Products Co. Part No. 46841 SAFETY PRECAUTIONS DANGER Machine must be
More informationOPERATING INSTRUCTIONS
CLEANMAX OPERATING INSTRUCTIONS FOR CLEANMAX STANDARD SERIES UPRIGHT VACUUMS MODELS : CMS-1T CMS-1N Before operating the vacuum, please read these instructions completely. Index Important Safety Instructions............................................................
More informationHi-Power Blenders MX1000XT, MX1050XT, MX1100XT OPERATING MANUAL
Hi-Power Blenders MX1000XT, MX1050XT, MX1100XT OPERATING MANUAL IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed including the following: 1. READ
More informationOPERATING INSTRUCTIONS
CLEANMAX OPERATING INSTRUCTIONS FOR CLEANMAX PRO SERIES UPRIGHT VACUUMS MODELS : CMPS-1T CMPS-1N Before operating the vacuum, please read these instructions completely. Index Important Safety Instructions............................................................
More informationOperating instructions Rotary iron HM
Operating instructions Rotary iron HM 21-140 To prevent accidents and machine damage read these instructions en - US, CA before installation or use. M.-Nr. 07 660 861 Contents Important Safety Instructions.................................................................3
More informationModel: C C Ambassador 20. Automatic Carpet Scrubber OPERATION SERVICE PARTS CARE
Ambassador 20 Automatic Carpet Scrubber Model: C8420-115 C8420-240 OPERATION SERVICE PARTS CARE This manual is furnished with each new Minuteman Ambassador 20. This provides the necessary operating and
More informationM O D E L G W T OPERATIONS MANUAL TABLE OF CONTENTS
M O D E L G W T - 202 OPERATIONS MANUAL TABLE OF CONTENTS INTRODUCTION... 1 SECTION 1 1.0 SAFETY... 1-1 1.1 EMERGENCY... 1-1 1.2 Know your machine... 1-1 1.3 Power Supply... 1-1 1.4 Keep guards in place....
More informationGCG-26c. Instruction Manual. G-Series Cooler
G-Series Cooler UPRIGHT COOLER Manual is for the following models: GCG-26-C14N7 GCG-26-C14NG GCG-26-C14NI GCG-26-C14NM GCG-26-C14NJ GCG-26 G-26-C14N7 G-26-C14NG G-26-C14NI G-26-C14NM G-26-C14NJ G-26 Instruction
More informationTable Of Contents 1 Introduction Safety notes Description of machine Machine Setup Using the Conveyor...
Table Of Contents 1 Introduction... 2 1.1 Pictograms... 2 1.2 Notes on the use of this handbook... 3 2 Safety notes... 3 2.1 General safety notes... 4 2.2 End of life... 5 3 Description of machine... 7
More informationINSTRUCTIONS FOR SAFE USE INSTRUCTIONS FOR SAFE USE
USER MANUAL INSTRUCTIONS FOR SAFE USE This appliance should only be used for domestic cleaning, as described in this user guide. Please ensure that this guide is fully understood before operating the appliance.
More informationUSER MANUAL KGNVCTBVAA
USER MANUAL KGNVCTBVAA IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
More informationIMPORTANT SAFEGUARDS WARNING
IMPORTANT SAFEGUARDS When using an electric appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduce the
More informationCanister Cleaner. Owner s Manual. Review this manual before operating cleaner. Thank you for selecting a HOOVER product
Canister Cleaner Owner s Manual ENGLISH pp. 1-9 ESPAÑOL pág. 10-14 FRANÇAIS p.15-19 Thank you for selecting a HOOVER product This cleaner was inspected and packaged carefully before being shipped from
More informationInstallation and Operation Instructions ELECTRIC FIREPLACE X56WMEF1BLK X56WMEF1WHT
Installation and Operation Instructions ELECTRIC FIREPLACE X56WMEF1BLK X56WMEF1WHT Tool list Assembly Instructions Important Safety Instructions Listing Approvals Glass Particles Installation Instructions
More informationHomeowner s Installation Instructions & Operating Manual
Wall Mounted Electric Fireplace Homeowner s Installation Instructions & Operating Manual Model: EF67B Series Used With Listed Front Facia Only: MT67C01 Black flat glass MT67C02 Black curved glass FOR YOUR
More information(The chances are you re never going to read me) Owner s Manual. Model S10E.
(The chances are you re never going to read me) Owner s Manual Model S10E www.simplicityvac.com 1 Contents Getting Started Important Safety Instructions 2 Polarization Instructions 3 State of California
More informationOwner s Manual. For Fuller Brush Tidy Maid Vacuum. Model FBTM-PW
Owner s Manual For Fuller Brush Tidy Maid Vacuum Model FBTM-PW Thank you for purchasing this Fuller Brush Upright Vacuum. To ensure the best results, please read this manual first and keep it for future
More information3-in-1 Breakfast Maker
-in-1 Breakfast Maker Model# GBF-70 USER MANUAL Read this manual thoroughly before using and save it for future reference Model: GBF70 2017 Gourmia www.gourmia.com The Steelstone Group Brooklyn, NY All
More informationEP Booklet Making Machine BMP350 Operation Manual. EP Equipment
EP Booklet Making Machine BMP350 Operation Manual EP Equipment Contents Introduction... 2 Safety Introductions... 3 Cautions Before Installation... 5 Power Supply... 5 Operation Environment... 5 Accessories...
More informationMaintenance. Maintenance
Maintenance This section includes: "Adding Ink" on page 7-32 "Emptying the Waste Tray" on page 7-36 "Replacing the Maintenance Kit" on page 7-39 "Cleaning the Paper Release Blade" on page 7-41 "Cleaning
More informationRead through the instructions carefully before using the appliance for the first time. Safeguard them for future reference.
Table of Contents Important Safeguards... 2 Additional Caution for Blower... 2 Parts... 3 Installing Charger Base... 4 Charging the Battery... 4 Important Note for Charging... 5 Indication Lights... 5
More informationVERNON ELECTRIC FIREPLACE
VERNON ELECTRIC FIREPLACE MODEL # 60351 CARE & USE GUIDE Please read this manual before installing and using your fireplace. IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, AN ELECTRICAL SHOCK
More information2200W RADIANT HEATER GVARH350. Instruction Manual
2200W RADIANT HEATER GVARH350 Instruction Manual Contents Guide to the Appliance 2 Caring for the Environment 3 Safety Information and Warnings 4 Operation Instructions 5 Care and Maintenance 6 Technical
More information