Technical Data Ducted Three Phase Split System Air Conditioner

Transcription

1 ENERGY EFFICIENT ISD / OSA 2 Technical Data Ducted Three Phase Split System Air Conditioner EXTRA LONG LIFE EPOXY COATED OUTDOOR COIL Nominal Cooling Capacity 26.5 kw (Total) JUNE 4

2 ISD / OSA 2 DUCTED THREE PHASE SPLIT SYSTEM AIR CONDITIONER GENERAL ISD 85Q, ISD 127Q, ISD 181Q, ISD 2Q - Indoor units usable for reverse cycle or cooling only OSA 2 - A general designation for outdoor unit OSA 2C - Outdoor unit, cooling only version OSA 2R - Outdoor unit, reverse cycle version The ISD indoor unit, together with its associated OSA outdoor unit, provides a three phase split system air conditioner designed and developed to comply with and exceed AS/NZS 3823 specified conditions (i.e. guaranteed cooling cycle performance at 43 C outdoor temperature). APPLICATIONS These units have been specifically developed for air conditioning of commercial and residential premises, e.g. offices, motels, homes, apartments, shops and restaurants. Distributing Capacity The outdoor unit can be matched to its own dedicated indoor unit. Alternatively, two split capacity indoor units can be coupled to the single compressor outdoor unit and controlled from one room thermostat. This tandem arrangement is often quieter than a larger single unit and permits air distribution closer to where it's needed most. The Indoor Unit options are: 1. One ISD 2Q (26.5 kw), 2. Two ISD 127Q (12.5 kw x 2 ), or 3. One ISD 85Q (8.5 kw) and one ISD 181Q (18.1 kw). Air Flow Selection The nominal indoor air flow and temperature /humidity conditions meet AS/NZS 3823 rating standards (incl. 5%RH). Consideration must always be given to selecting an air flow and face velocity that avoids water carry-over problems. High humidity levels can occur in tropical or subtropical conditions, and/or when heavily moisture laden fresh air is introduced. If the air returning to the indoor coil is regularly expected to be above 5%RH, then the coil face velocity should be limited to be 2.5 m/s or less (refer Air Flow graph; 2.5 m/s is clearly marked). Applications using full or high proportions of fresh air should be referred to your nearest temperzone sales office to establish the correct selection of units. FEATURES Efficient. The outdoor unit has a high efficiency scroll compressor. Heat exchange coils incorporate inner grooved (rifled) tube for better heat transfer. Performance. A dynamically balanced forward curved fan with a multi-speed motor enables fine tuning of the indoor unit to match the supply air requirements. The system includes a temperature sensing head pressure control which enables the system to run efficiently on cooling cycle at outdoor ambient temperatures below C, and heating cycle above C. Quiet. The compressor is isolated in a builtin, insulated compartment to minimise noise. The indoor unit is also insulated for noise attenuation. Slimline. The compact upright design of the outdoor unit requires only a mm gap on the coil side where installation is against a wall. Its slimline cabinet is particularly practical where there is restricted space, e.g. side access pathways, balconies, narrow ledges, etc.. Durable. The outdoor coil fins are epoxy coated for extra protection in corrosive environments, e.g. salt laden sea air. The outdoor unit's cabinet is constructed from high grade galvanised steel polyester powder coated for all weather protection (IP 45). External fasteners are stainless steel. Heat exchange coils comprise aluminium plate fins on mechanically expanded rifled copper tube. The indoor unit's cabinet is constructed from high grade galvanised steel and includes a plastic drain tray for complete corrosion resistance. Service Access. The indoor unit's built-in drain tray can be removed for ease of cleaning and service accessibility. Insulation. Closed cell foam insulation has been used in the indoor unit's cabinet to ensure no particles are introduced into the air stream. The insulation is foil faced and meets fire test standards AS 3.3 (1989) and BS 476 parts 6 & 7. Mounting. The indoor unit can be mounted rigid, or using the optional spring mounting brackets which minimise transfer of vibration. Self Diagnostics. The Outdoor Unit Controller (OUC) has a display of LEDs to indicate faults and running conditions. A general fault indicator is included for interface to external systems. ORIES Outdoor Unit: 1. LP switch. 2. Fault indicating auxillary relay board. Indoor Unit: 1. Filter box - integrated return air spigot and washable filter (rated EU2). 2. temperzone TTS-1 Wall Thermostat kit 3. Spring Mounting Kit. 4. Electric booster heater box - complete with safety cutouts required to meet AS/NZS ISD 85Q: 2 kw ISD 127Q: 3 kw ISD 181Q: 4.5 kw ISD 2Q: 4.5 kw. 5. Supply and return air plenums. SAFETY FEATURES 1. HP and loss of refrigerant protection. 2. Anti-rapid cycle timer and internal overload for compressor protection. 3. Circuit breaker control circuits. 4. Time-and-temperature controlled electronic de-ice switch prevents icing up of the outdoor coil during heating cycle (OSA 2R only). 5. Frost protection on cooling cycle. 6. Sensor fault indication. 7. Crankcase heater prevents liquid refrigerant condensing in the compressors during the 'off' cycle. 8. Compressor minimum run time to ensure oil return. COMPRESSOR Each high efficiency scroll type compressor is hermetically sealed, quiet running and supported on rubber mounts to minimise vibration. REFRIGERATION PIPING The standard unit allows for a line length of up to 3 m. Max. height separations between units are : Reverse Cycle systems: Outdoor unit above indoor unit : 12 m Outdoor unit below indoor unit : 12 m. Cooling Only systems: Outdoor unit above indoor unit : 18 m Outdoor unit below indoor unit : 12 m. For extended line lengths contact your nearest temperzone sales office for additional details on piping requirements. The OSA 2 is shipped from the factory with a charge of HCFC-22 (R22) refrigerant sufficient for a 1 m line length. Liquid and suction service valves are provided. Accurator expansion devices control the flow of refrigerant. The matched indoor units are shipped with a holding charge of nitrogen. Both units have one flare and one brazed pipe connection. TANDEM PIPING When connecting two indoor units in tandem to the OSA 2R outdoor unit ensure the following: 1. Maximum line length specified for the outdoor unit must include both tandem legs. 2. Tandem legs must be as close as possible to equal, after leaving the common leg. 3. Ensure each 'T' joint connection is the same size as the common leg's pipe size, downsizing if necessary from there to each indoor unit. WIRING The electrical supply required (including voltage fluctuation limits) is: 3 phase V a.c. 5 Hz with neutral and earth. The compressor crankcase heater requires a 24 hour power supply. A control panel, located in the outdoor unit, is fully wired ready to accept the main power supply. The manufacturer operates a quality management system that conforms to AS/NZS ISO 91:.

3 COMBINATIONS ISD 2Q (26 kw) OSA 2 ISD 127Q (12.7 kw) OSA 2 ISD 127Q (12.7 kw) ISD 181Q (18 kw) OSA 2 ISD 85Q (8.5 kw)

4 PERFORMANCE DATA COOLING CAPACITY (kw) Total = Total Capacity (kw) Sens. = Sensible Capacity (kw) E.A.T. = Entering Air Temperature = Nominal Capacity (kw) Note: Capacities are gross and do not include allowance for fan motor heat loss. Capacities are for close coupled systems. Interconnecting pipework will reduce capacity (refer page 6). MODELS INDOOR INDOOR COIL FAN OUTDOOR COIL ENTERING AIR TEMPERATURE C D.B. E.A.T. Indoor Outdoor AIR W.B. D.B SPEED Unit Unit l/s C C Total Sens. Total Sens. Total Sens. Total Sens. Total Sens. Total Sens ISD 127Q / OSA ISD 85Q / OSA ISD 181Q / OSA ISD 2Q / OSA Indoor Air Flow Correction nominal conditions Indoor Air Flow (%) -% -1% Rated +1% Total Capacity Sensible Capacity PIPE LENGTH CAPACITY LOSS ON COOLING CYCLE DUE TO PRESSURE DROP Note: Loss percentage is approximate only. No allowance made for vertical piping. Pipe Size (mm) Equivalent Line Pipe Length (m) System Liquid Suction ISD 85Q / OSA 2 ISD 127Q / OSA 2 ISD 181Q / OSA % 1.6 % 2.25 % 4 % 3.2 % 4. % 6 % 4.7 % 5.6 % 8 % 7.3 % %.8 % 1.2 % 1.5 % 1.6 % 1.7 % 2.5 % 2.4 % 2.25 % 3.5 % 3.2 % 2.7 % ISD 2Q / OSA % 3.75 % 5 % Suction Pipe Size OD Additional Pipe Length to allow per Bend Long 9 Radius (2 x pipe dia.) 16 mm.3 m 19 mm.4 m 22 mm.5 m 28 mm. m Reverse Cycle Systems MODELS Indoor Outdoor Unit Unit ISD 85Q / OSA 2R ISD 127Q / OSA 2R ISD 181Q / OSA 2R ISD 2Q / OSA 2R INDOOR ENTERING AIR TEMP. C D.B HEATING CAPACITY (kw) G = Gross Heating Capacity kw, based on nominal air flows. N = Net Heating Capacity kw allowing for average defrost. = Nominal Capacity (kw) OUTDOOR COIL ENTERING AIR TEMPERATURE (E.A.T.) C D.B G N G N G N G N G N G N G N G N

5 PERFORMANCE DATA ISD 85Q AVAILABLE EXTERNAL PRESSURE (Pa) 1 ISD 181Q AVAILABLE EXTERNAL PRESSURE (Pa) l/s - Pa 1.1A 1.1A 1.A.9A l/s - W A 2.5A 2.8A 3.4A AIR VOLUME (l/s) 2.5 m/s Face Velocity l/s - Pa 2.5A 2.A 3.2A l/s - W A 4.A 5.7A AIR VOLUME (l/s) 2.5 m/s Face Velocity INPUT (watts) INPUT (kw) AIR HANDLING Note: In a free blow application, beware of exceeding indoor fan motor's full load amp limit. As filters are optional, air flows given are for ISD units without filter installed. ISD 127Q AVAILABLE EXTERNAL PRESSURE (Pa) 4 1.9A 1 ISD 2Q AVAILABLE EXTERNAL PRESSURE (Pa) 2.3A.8A l/s - Pa l/s - W 9 2.4A 3.7A 4.1A AIR VOLUME (l/s) 2.5 m/s Face Velocity 1 3.5A 4.A 3.6A l/s - Pa l/s - W A 4.5A 7.A AIR F (l/s) 2.5 m/s Face Velocity INPUT (watts) INPUT (kw) ISD 127Q (x2) ISD 85Q + 181Q ISD 2Q E.E.R. (cooling) Indoor Fan Full Load Amps 5. (x2) 6.3 & (x2) Running Amps (Total System) / 17 / 17 / 19 / / 14 / 14 Recommended External Fuse 4 A 4 A 4 A FILTERS - PRESSURE DROP PRESSURE DROP (Pa) Based on EU-2 rated filter media 4 FINAL PRESSURE 3 DROP 125 Pa 1 INITIAL (Clean Filter) Filter Areas: ISD 85Q m 2 ISD 127Q -.2 m 2 ISD 181Q -.48 m 2 ISD 2Q -. m 2 FILTER FACE VELOCITY (m/s)

6 PERFORMANCE DATA Indoor Unit - Supply Air Outlet MODEL ISD 85Q ISD 127Q ISD 181Q ISD 2Q FAN SPEED - - AIR F l/s SWL db(a) Supply Air Outlet + Insulated Duct * MODEL ISD 85Q ISD 127Q ISD 181Q ISD 2Q FAN SPEED AIR F l/s SWL db(a) SOUND LEVELS Sound Power Levels (SWL) Test Conditions: BS 848 PT Installation Type A (free inlet and outlet). Direct method of measurement (reverberant room). Measured in decibels re 1 picowatt OCTAVE BAND FREQUENCY Hz 5 1 k SOUND POWER LEVELS (SWL) db OCTAVE BAND FREQUENCY Hz 5 1 k SOUND POWER LEVELS (SWL) db k k k k * 1 metre of 25 mm insulated duct Outdoor Unit OCTAVE BAND FREQ. Hz SPL OCTAVE BAND FREQ. Hz MODEL FAN SPEED SWL db(a) k 2 k SOUND POWER LEVELS db 4 3 m db(a) k 2 k 4 k SOUND PRESSURE LEVELS db OSA Sound Pressure Level (SPL) in decibels re µpa.

7 Dimensions (mm) PROJECTION Not to Scale ISD 85Q, 127Q Indoor Unit ISD 85Q ISD 127Q Net Weight 38 kg 45 kg Shipping Weight 41 kg 48 kg 85 C SPRING MTG CTRS D HANGING A ELECTRIC HEATER BOX FILTER BOX Note : Allow 5 mm minimum clearance to each access panel. 5 SPRING MTG 53 HANGING B 4 MOUNTING SLOTS x 9 CONDUIT HOLES REFRIGERANT CONNECTIONS 6 FAN VIA REMOVEABLE BASE & DRAIN TRAY MODEL ISD 85Q ISD 127Q 6 A B C D E Recommended Pipe Sizes (mm OD) ISD 85Q ISD 127Q Suction: Liquid: OA E OVERALL DRAIN 19 OD OA ISD 181Q Indoor Unit Net Weight Shipping Weight kg kg SPRING MTG CTRS 124 HANGING ELECTRIC HEATER BOX 35 FILTER BOX Note : Allow 5 mm minimum clearance to each access panel. 5 SPRING MTG 53 HANGING CONDUIT HOLES REFRIGERANT CONNECTIONS MOUNTING SLOTS x 9 6 FAN VIA REMOVEABLE BASE & DRAIN TRAY 6 Recommended Pipe Sizes Suction: 22 mm OD Liquid: 13 mm OD 425 OA OVERALL DRAIN 19 OD OA 6

8 DIMENSIONS (mm) Not to Scale ISD 2Q Indoor Unit Net Weight 84 kg Shipping Weight 93 kg SPRING MTG CTRS 124 HANGING Note : Allow 5 mm minimum clearance to each access panel. 5 SPRING MTG 53 HANGING CONDUIT HOLES REFRIGERANT CONNECTIONS MOUNTING SLOTS x ELECTRIC HEATER BOX FAN VIA REMOVEABLE BASE & DRAIN TRAY 6 FILTER BOX 555 OVERALL 23 5 DRAIN 19 OD 1365 OVERALL OA OSA 2 Outdoor Unit MIN. CLEARANCE OSA 2C OSA 2R Net Weight 7 kg 211 kg Shipping Weight 2 kg 219 kg Note Materials and specifications are subject to change without notice due to the manufacturer's ongoing research and development programme. MIN. CLEARANCE 1 MIN. CLEARANCE MIN. CLEARANCE MIN. CLEARANCE Recommended Pipe Sizes Suction: 28 mm OD Liquid: 13 mm OD SERVICE 125 OA DIA. CONDUIT HOLES PROJECTION REFRIG. CONN'S DIA. DRAIN HOLE 5 MTG CTR 65 OA DIA. DRAIN HOLE 828 MTG CTR DIA. SLOTS OA DIA. DRAIN HOLE Available from AUCKLAND Ph Fax WELLINGTON Ph Fax CHRISTCHURCH Ph Fax /4 Pamphlet No temperzone limited 4 temperzone limited Head Office, Auckland : 38 Tidal Rd, Mangere, N.Z. Private Bag 9333, Otahuhu, NEW ZEALAND. sales@temperzone.co.nz Website: temperzone australia pty ltd Head Office, Sydney : 7A Bessemer St PO Box 48, Delivery Centre, Blacktown, NSW 2148, AUSTRALIA. sales@temperzone.com.au SYDNEY Ph. (2) Fax (2) ADELAIDE Ph. (8) Fax (8) SINGAPORE Ph. SNG Fax SNG 35 8 MELBOURNE Ph. (3) Fax (3) BRISBANE Ph. (7) Fax (7) NEWCASTLE Ph. (2) Fax (2) REGISTERED AS/NZS ISO 91: S U P P L I E R PERTH Ph. (8) Fax (8) TOWNSVILLE Ph. (7) Fax (7) HOBART Ph. (3) 72- Fax (3) Manx Press