INSTALLATION INSTRUCTIONS GT4011EE TWO POINT HOIST

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS GT4011EE TWO POINT HOIST"

Louise Harris
6 years ago
Views:

INSTALLATION INSTRUCTIONS GT4011EE TWO POINT HOIST USED W/ USED W/ STANDARD CEILING POWERTRAK INSTALLATION INSTALLATION SUPPLIED ITEMS METHOD METHOD QUANTITY DESCRIPTION 1 SELF-LOCKING

SCREW EYE X X 2 PIGTAIL LAG SCREWS X 4 4 LAG SCREW X 4 WASHERS X TOOLS REQUIRED - ELECTRIC DRIVER / DRILL & 3/32" & 7/32" BIT TAPE MEASURE / PENCIL STEP LADDER SAFETY GLASSES STUD FINDER

) TWO INSTALLATION METHODS ARE DETAILED ON THE FOLLOWING PAGES 1 RECOMMENDED INSTALLATION W/ CEILING POWERTRAK & RING HOOKS PGS 2 THRU 4 THIS INSTALLATION REQUIRES THE ADDITIONAL PURCHASE

1 INSTALLATION INSTRUCTIONS GT4011EE TWO POINT HOIST USED W/ USED W/ STANDARD CEILING POWERTRAK INSTALLATION INSTALLATION SUPPLIED ITEMS METHOD METHOD QUANTITY DESCRIPTION 1 SELF-LOCKING SAFETY BLOCK & TACKLE W/ X X 28 FT OF DROP CORDS 35 FT OF HOISTING CORD 2 WEB STRAPS W/ METAL BUCKLES X X 2 MICRO PULLEY X X 1 SHACKLE X X 1 ORGANIZER BLOCK X 2 #10 X 2 1/2" LG SCREWS X 1 SCREW EYE X X 2 PIGTAIL LAG SCREWS X 4 4 LAG SCREW X 4 WASHERS X TOOLS REQUIRED - ELECTRIC DRIVER / DRILL & 3/32" & 7/32" BIT TAPE MEASURE / PENCIL STEP LADDER SAFETY GLASSES STUD FINDER OR SMALL BRAID NAILS & HAMMER (TO LOCATE JOIST IF INSTALLING THROUGH DRYWALL.) TWO INSTALLATION METHODS ARE DETAILED ON THE FOLLOWING PAGES 1 RECOMMENDED INSTALLATION W/ CEILING POWERTRAK & RING HOOKS PGS 2 THRU 4 THIS INSTALLATION REQUIRES THE ADDITIONAL PURCHASE OF CEILING POWERTRAK AND 2 RING HOOKS. THIS INSTALLATION HAS A MUCH NICER APPEARANCE AND IS EASIER TO INSTALL & ADJUST. 2 STANDARD INSTALLATION WITH SUPPLIED PARTS PGS 5 THRU 8 THIS INSTALLATION IS DONE WITH THE SUPPLIED PARTS AND MOUNTS TO A 2X6 BOARD. PG 1 QUESTIONS???? CALL REV 1, 12/1

SPECIFICATIONS & OPERATION MAXIMUM LIFTING LOAD 60 LBS MINIMUM LIFTING LOAD 15 LBS (SEE FURTHER INFO BELOW) MAXIMUM VERTICAL LIFT 16 FT (SEE FURTHER INFO BELOW) MECHANICAL ADVANTAGE 3:1 THE

WHEN THE CORD IS RELEASED, THE SPRING LOADED ARM'S TEETH PRESSES AGAINST THE CORD, HOLDING THE CORD IN PLACE.

THIS IS WHY A 15 LB. MINIMUM LOAD IS REQUIRED. ie. LESS THAN 15 LBS OF TENSION WILL NOT OPEN THE SPRING LOADED CLEAT.

THE MAXIMUM VERTICAL LIFT DISTANCE IS DEFINED AS 16 FT AND CAN BE USED IN A GARAGE WITH 18 FT HIGH CEILINGS.

2 SPECIFICATIONS & OPERATION MAXIMUM LIFTING LOAD 60 LBS MINIMUM LIFTING LOAD 15 LBS (SEE FURTHER INFO BELOW) MAXIMUM VERTICAL LIFT 16 FT (SEE FURTHER INFO BELOW) MECHANICAL ADVANTAGE 3:1 THE UNIQUENESS OF THIS HOIST SYSTEM IS THE SELF-LOCKING SAFETY CLEAT. IT HAS A SPRING LOADED ARM WHICH HOLDS THE CORD IN PLACE WHEN UNATTENDED. WHEN RAISING AN ITEM, THE CORD SLIDES PAST THE ARM. WHEN THE CORD IS RELEASED, THE SPRING LOADED ARM'S TEETH PRESSES AGAINST THE CORD, HOLDING THE CORD IN PLACE. TO LOWER AN ITEM, 1) YOU MUST STAND AWAY AND THIS "OPENS" THE SAFETY ARM AND 2) THEN WHEN THE ARM IS OPEN, YOU SLOWLY RELEASE THE CORD, ALLOWING IT TO "SLIDE" PAST THE ARM'S TEETH. THIS IS WHY A 15 LB. MINIMUM LOAD IS REQUIRED. ie. LESS THAN 15 LBS OF TENSION WILL NOT OPEN THE SPRING LOADED CLEAT. THE LENGTH OF THE HOISTING (PULL) CORD IS 35 FT AND THE STRAP ASSEMBLY IS APPROXIMATELY 2 FT. THE MAXIMUM VERTICAL LIFT DISTANCE IS DEFINED AS 16 FT AND CAN BE USED IN A GARAGE WITH 18 FT HIGH CEILINGS RECOMMENDED INSTALLATION W/ CEILING POWERTRAK & RING HOOKS STEP 1A STEP 1B STEP #1A: CHECK PARTS RECEIVED. WHEN INSTALLING THE HOIST USING A CEILING POWERTRAK CHANNEL THE ABOVE PARTS W/O THE X ARE USED. STEP #1B: REQUIRED IS THE ADDITIONAL PURCHASE OF 2 RING HANGER HOOKS (GT9002E) AND THE CEILING POWER TRAK (GT E). BOTH ITEMS CAN BE FOUND IN THE CEILING SYSTEMS CATEGORY OF THE ESTORE. PG 2 QUESTIONS???? CALL REV 1, 01/12

STEP #2: PLAN THE LOCATIONS OF THE EYE SCREW,

THE BLOCK / TACKLE TO THE EYE SCREW WITH THE

STEP #4: SLIDE ON THE 2 MICRO PULLEYS ON THE

3 STEP #2: PLAN THE LOCATIONS OF THE EYE SCREW, POWERTRAK AND RING HOOKS PER THE ABOVE SKETCH. INSTALL THESE COMPONENTS. STEP 2 STEP 2 STEP 3 STEP 4 STEP #3: ATTACH THE BLOCK / TACKLE TO THE EYE SCREW WITH THE SUPPLIED SHACKLE. STEP #4: SLIDE ON THE 2 MICRO PULLEYS ON THE RING HANGERS AND FED THE DROP CORDS THROUGH THEM. PG 3 QUESTIONS???? CALL REV 1, 01/12

SYSTEM SETUP STEP 5 STEP 5 STEP #5: PLACE THE OBJECT TO BE HOISTED UNDER THE RING

TRY TO TIE THE STRAPS ONTO THE DROP CORDS AT THE SAME HEIGHT.

(BOTH DROP ROPES MUST HAVE EQUAL TENSION SO THE LOAD REMAINS LEVEL WHEN LOWERING OR

4 SYSTEM SETUP STEP 5 STEP 5 STEP #5: PLACE THE OBJECT TO BE HOISTED UNDER THE RING HOOKS AND TIE THE DROP CORDS TO THE STRAPS. TRY TO TIE THE STRAPS ONTO THE DROP CORDS AT THE SAME HEIGHT. STEP #6: FASTEN THE STRAPS TO THE OBJECT TO BE LIFTED AND ADJUST THE STRAP LENGTHS AS NEEDED SO THE LOAD IS LEVEL. STEP #7: SLOWLY PULL THE RAISING CORD TO CHECK THE LOAD IS LEVEL. (BOTH DROP ROPES MUST HAVE EQUAL TENSION SO THE LOAD REMAINS LEVEL WHEN LOWERING OR RAISING.) THE METHOD USED TO RAISE OR LOWER AND OBJECT IS SHOWN / EXPLAINED ON PAGE 2. STEP 6 STEP 7 A FINAL SAFETY NOTE: NEVER RAISE OR LOWER AN ITEM WITH A PERSON UNDER THE OBJECT. PG 4 QUESTIONS???? CALL REV 1, 01/1

5 STANDARD INSTALLATION WITH SUPPLIED PARTS THESE INSTRUCTIONS INSTALL THE HOIST ON A 2X6 WOOD BOARD AND THEN SCREWING THE BOARD TO THE CEILING. PG 5 QUESTIONS???? CALL REV 1, 01/1

6 PG 6 QUESTIONS???? CALL REV 1, 01/1

7 PG 7 QUESTIONS???? CALL REV 1, 01/1

8 PG 8 QUESTIONS???? CALL REV 1, 01/1

INSTALLATION INSTRUCTIONS GT8500E / GT8501E MASTER FLUORESCENT FIXTURE / SLAVE FLUORESCENT FIXTURE

CARTON CONTENTS QUANTITY DESCRIPTION INSTALLATION INSTRUCTIONS GT8500E / GT8501E MASTER FLUORESCENT FIXTURE / SLAVE FLUORESCENT FIXTURE 1 GT8500, MASTER FLUORESCENT FIXTURE OR 1 GT8501, SLAVE FLUORESCENT