W6636 East Avenue North, Onalaska, WI USA (608) Fax: (608)

Size: px

Start display at page:

Download "W6636 East Avenue North, Onalaska, WI USA (608) Fax: (608)"

Brook Gregory
6 years ago
Views:

1 W6636 East Avenue North, Onalaska, WI USA (608) Fax: (608) F B-09

2 2

3 3

4 GAZ PLYNNY 25 I 3P GAZ BUTANOWY 20 I 3B/P 10 I 2H, I 2E, and I 2E(S)B, GAZ ZIEMNY 4

5 Kategoria i cisnienie gazu (mbar) I 3P (37) 5

6 6

7 7

8 8

9 TABS DIVERTER HALVES NOTCHES IN MOUNTING TABS OUTLET SCREWS FORMED OUTLET GUAR 9

10 WALL E BOLT NUT WASHER CHAIN NOTE: REGULATORS SHOULD ALWAYS BE MOUNTED OUTDOORS. IF CIRCUMSTANCES FORCE INSTALLING THE REGULATOR INDOORS, THE REGULATOR'S VENT MUST BE VENTED OUTDOORS USING VENT LINE NO SMALLER THAN VENT OPENING. VENT OF REGULATOR MUST MANUAL SHUT-OFF VALVE POINT DOWN AND REGULATOR CAN BE INSTALLED BEFORE MUST BE VENTED OUTDOORS THE REGULATOR, UNDER THE EAVE OF THE BUILDING, OR AFTER THE REGULATOR INSIDE THE BUILDING. WASHER NUT HEATER TOP CHAIN OR CABLE OPTIONAL INDOOR REGULATOR MOUNTING LOCATION GAS HOSE THERMOSTAT CORD HEATER AIR DIVERTER BLACK PIPE THROUGH WALL VENT LINE WALL OUTLET POWER CORD THERMOSTAT 30.5CM 30.5CM SEDIMENT TRAP NIPPLE TO GAS CONTROL VALVE INLET HOSE ADAPTER TEE NIPPLE CAP 10

11 GAS FLOW PIPING ADAPTER VALVE, MANUAL SHUT-OFF NIPPLE 1/2" REGULATOR REGULATOR VENT PIPING ADAPTER ADAPTER GAS HOSE ADAPTER TO GAS CONTROL SEDIMENT TRAP VALVE INLET 11

12 ON OFF RESET SWITCH 12

13 13

14 MOTOR MOUNT PLATE FAN WHEEL MOTOR CLEARANCE NUTS PADDLE HOUSING SIDE PANEL SWITCH W/PADDLE LEADS OBLONG HOLE 14

15 FLAME SENSOR HEAT CHAMBER kw: 3 mm kw: 4 mm NER IGNITER IGNITER/SENSO ENCLOSURE REMOVE SCR REMOVE SCREW (65,9 kw MODEL BURNER REMOVE SCREWS REMOVE FROM VALVE CONTROL BOX LOOSEN UNION REMOVE FROM VALVE REMOVE SCREWS REMOVE SCREWS 15

16 10 55 OUTLET PRESSURE TAP SCREW 16 INTERNAL PRESSURE REGULATOR LOW PRESSURE GAUGE INLET PRESSURE OFF ON INLET PRESSURE TAP OUTLET PRESSURE TAP LOW PRESSURE GAUGE

17 RESET BUTTON TERMINAL MOUNTING LEG SENSING SURFACE FLAME 17

18 18

19 Problem 19

20 Problem 20

21 Problem 21

22 Problem 22

23 17.6 kw MODEL CAUTION - REFER TO THE HEATER'S ELECTRICAL CONNECTION DIAGRAM WHEN SERVICING THE HEATER'S ELECTRICAL COMPONENTS TO AVOID WIRING ERRORS & EQUIPMENT MALFUNCTION. CHECK FOR PROPER OPERATION AFTER SERVICING. WARNING: THIS HEATER MAY START AT ANY TIME HIGH VOLTAGE IGNITION LEAD IGNITER WHITE FLAME SENSOR BURNER GROUND WHITE JT2 JT1 J6 J5 DSI CONTROL J2 J3 J1 GAS HIGH LIMIT CONTROL SWITCH(ES) TRANSFORMER FUSE YELLOW YELLOW BROWN YELLOW BLUE BLUE BROWN GREY WHITE AIR PROVING SWITCH BROWN BLUE RED RESET SWITCH WHITE BLUE BROWN OPTIONAL THERMOSTAT BROWN BLUE BLUE BROWN FAN MOTOR CASE GROUND GREEN/ YELLOW BLUE POWER CORD BROWN ELECTRICAL CONNECTION DIAGRAM GROUND GROUND BURNER GROUND GROUND NEUTRAL L1 HIGH LIMIT SWITCH(ES) SOLENOID(S) GROUND MOTOR OPTIONAL THERMOSTAT GROUND FUSE TRANSFORMER J2 IGNITER 24V 240V JT2 JT1 J6 J3 J5 FLAME SENSOR AIR PROVING SWITCH RESET SWITCH J1 DSI CONTROL ELECTRICAL LADDER DIAGRAM IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE HEATER MUST BE REPLACED, IT MUST BE REPLACED WITH WIRING MATERIAL HAVING A TEMPERATURE RATING OF AT LEAST 302ºF (150ºC) 23

24 65,9 kw MODEL CAUTION: REFER TO HEATERS ELECTRICAL CONNECTION DIAGRAM WHEN SERVICING THE HEATERS ELECTRICAL COMPONENTS TO AVOID WIRING ERRORS AND EQUIPMENT MALFUNCTION. CHECK FOR PROPER OPERATION AFTER SERVICING. WARNING: THIS HEATER MAY START AT ANY TIME HIGH VOLTAGE IGNITION LEAD IGNITER WHITE FLAME SENSOR BURNER GROUND WHITE JT2 JT1 J6 J5 DSI CONTROL J2 J3 J1 HIGH LIMIT GAS SWITCH(ES) CONTROL TRANSFORMER FUSE YELLOW YELLOW BROWN YELLOW BLUE BLUE BROWN GREY WHITE AIR PROVING SWITCH BROWN BLUE RESET RED SWITCH WHITE BLUE BROWN MOTOR RELAY BLUE BLUE BLUE BLUE BROWN BROWN BROWN BROWN OPTIONAL THERMOSTAT BROWN BLUE BLUE FAN MOTOR BROWN CASE GROUND GREEN/ YELLOW BLUE POWER BROWN CORD ELECTRICAL CONNECTION DIAGRAM GROUND GROUND BURNER GROUND GROUND NEUTRAL L1 HIGH LIMIT SWITCH(ES) SOLENOID(S) GROUND MOTOR RELAY MOTOR OPTIONAL THERMOSTAT GROUND FUSE DSI CONTROL TRANSFORMER IGNITER J2 JT2 24V 240V JT1 J6 GROUND J3 J5 AIR PROVING SWITCH RESET SWITCH J1 FLAME SENSOR ELECTRICAL LADDER DIAGRAM IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE HEATER MUST BE REPLACED, IT MUST BE REPLACED WITH WIRING MATERIAL HAVING A TEMPERATURE RATING OF AT LEAST 302ºF (150ºC) 24

25 25

27 27

28 20384 DANGER HIGH VOLTAGE ISOLATE PSI LABEL CE LABEL WARNING WARNING TECH DATA HOT SURFACE RESET SWITCH ELECTRICAL GROUNDING HOT SURFACE WIRING DIAGRAM KW KW DANGER HIGH VOLTAGE INSTRUCTIONS 28

29 29

10 I 2H, I 2E, and I 2E(S)B,

10 I 2H, I 2E, and I 2E(S)B, !>BCAD;3:1 DVHC;?F>9;1 AI5:>9;9 4;^F 7?B@?41ABCF A?H38 9 8?4?FH38 *5A91 +H@ %?3 I1@S?>D 7AI5:>1 #F 5I@?BA54>9 01@S?> (1