GS08 OPERATION&INSTRUCTION MANUAL

Transcription

1 G08 OPERATION&INTRUCTION MANUAL (3kW 18kW)

2 G08 Cataloge Ä Â¼ Prologue Users instruction The selection of the place of the steam equipment installation The typical illustration of the steam equipment installation Installation of the tube Drawing of the steam generator Electric requirements Power line assemble illustration Wiring Diagram V(3PH) Wiring Diagram 08V(3PH) Wiring Diagram 0-40V(1PH/PH) Installation of the top light Choose your models Maintenance of the stream generator team generator structure drawing Usual malfunction and resolve pecification

3 Prologue ÐòÑÔ Óû ÐëÖª Users instruction G08 Welcome to use G08 series stream generator,this series contains a steam furnace and a controller.you can adjust the tempeture of the sauna room and set the working time of the steam as you wish.and the system contains a overheat/dry-burnt protection system and a security valve.it could prevent the overheating and assure the steam furnace working at a regular air pressure.it has the reasonable design and working very stable,very convenient to install, healthy and comfortable,is the top grade sauna equipment for the modern family, hotel,restaurant,meeting place and the club.you will be satisfied with the noticeable effects on pain relief,weight control,skin stimulation and stress reduction due to an increased blood circulation got from steam bath. Gs08 series include 9 types of machines that output power varies in 3kW,4.5kW,6kw,7.5kw, 9kw,10.5kW,1kW,15kW,18kW,the users could choose it according to their requirements. Caution: Î ±¾ÊÖ²áÖ Òý ² ʹÓõ¼ÖµÄÒâÍâ ±¾¹«We are not responsible for the malfunction and damage came from the installation that not comply to the users manual. ¾ æ: 1.Make sure the model and the accessories are correct, include the voltage input..make sure the steam power are matched with the sauna room' dimension. Pay much attention to the steam room's cubage and construction. If you have any problem, please refer to the Page 11 about the dimension selection. 3. Make sure to read this manual carefully for the secure and effective use. 4.We shall not be responsible for the product damage or malfunction caused by selfinstallation or the operation procedures which is not operated by the users instructions. 5.G08 series are packaged with a case, please check the goods when it arrived to assure it is in good condition, if you find any damage in the package, please contact the transportation company or the supplier to claim for compensation. 6.This product must be used indoor. Choosing a right location Important: Install an exhaust fan outside of the steam room in case that it can expel the excessive steam from the shower room. ÖØÒª: ome locations recommended to customers for the right installation. 1.The distance to the steam room less than 6m, the standard pipe which link the controller and the steam generator should be 6.5m..The steam generator should not be installed in the steam room 3.Not installed outdoor or in any places that will influence the security of the machine by the environment. 4.Do not install it in the frigid loft or any places the water will freeze. 5.Do not install it near the burnable and caustic object or chemical(coal gas or dope thinner etc.) 6.Installed in a dry place and the ventilation is good. Page 1

4 G08 7.table and horizontal.the steam generator has a hanging groove for immobility on wall.make sure the machine is steady and horizontally installed. 8.On both sides and the top of the steam generator need to reserve at least 1 inches space. 9.The place where the machine is installed must be easily cleaned up and convenient for the disassembly of the machine. 10.The installation place must be convinent for the drain of water in inner pot. 11.The steam tube,safty valve, drain valve,water tube,steam outlet are still very heated after the steam generator have stopped working for some time.must take some measures for example using the heat insulation tube to prevent the damage of the hot tube and keep the outlet away from the people. 1.The controller must be installed in the steam room,please refer to the chapterinstruction of the controller's installation and operation of the manual. Attention: The steam generator(including the controller) are comply with the CE and UL certificate,and are adaptive in the moisture environment. Installation drawing of the steam generator Control panel Attention: The drawing is only for explanation.as for practical design of steam room, please consult with qualified designer, architect or builder. upply team outlet pipe Pressure relief valve Water Inlet Pipe team generator Water Drain Valve team Outlet Page

5 Installation of pipeline Water supply pipe (1/'') 1.Connect hot water or cold water pipes. It had better be hot water pipe with a temperature o no more than 70 C..Install stop valve in the water supply pipe. The stop valve should be installed in a place where it is easily operated in emergency. 3.Clean the water supply pipe completely before connecting the water pipe to the steam engine. 4.It is suggested that filter and anti-furring equipment in the water supply pipe. 5.The water pressure should be at best between 15 and 0 pounds/square inch. If necessary, decrease the pressure accordingly. 6.If necessary, install equipment to prevent the water producing sound. Òâ: Òâ: G08 Warning: The installation of all the pipes should be operated by qualified plumbers with corresponding operation certificate in accordanceance with national requirements: 1.Use joints when connecting pipes..use brass pipes or copper hoses only. 3.Do not use black and galvanized or PVC pipes. team pipe (3kW/4.5kW pipe size: 1/'' 6kw & above:3/4'') 1.Do not install any valves in the steam pipes. The steam can never be obstructed..install a brass steam pipe( 3kW/4.5kW pipe size: 1/'' 6kw & above:3/4'') as connector between the steam outlet and the steam nozzle. 3.The heat insulation material used to insulate the steam pipe should be resistant to o temperature as high as 10 C or higher. 4.The horizontal part of the steam pipe should be installed inclining to the steam outlet or in the direction of steam engine. Do not bend it in a hape to make sure that the cooled water will not stay in the curved pipe of the steam pipe. 5.The shorter the steam pipe, the better. Try to decrease the number of elbows and avoid abrupt turns. Attention: Do not install the steam pipe in an upper or lower direction now and then, which will affect the output of steam. team nozzle (3kW/4.5kW pipe size: 1/'' Atte ntion: ince the steam nozzle and steam outlet are very hot, try to avoid install the steam nozzle in the position which will easily come into contact with the person in a bath in case the steam should splash to scald the user. 1.Install the steam nozzle in the position 6-1 inches above the ground. If the steam bath is in the bathtub or bathroom, install the steam nozzle 6 inches above the bathtub. If the steam room above adopts materials like acryl or non-heat-resistant sheet, install additional heat insulator..the steam spray outlet should be installed face down. Wind a few circles of green material belt around the whorl of the steam pipe, install the steam nozzle and tighten with hands. Attention : In order to protect the steam nozzle, do not use the spanner or other tools to tighten, use a little soap water and soft sponge to wipe, and do not use erosive chemical solutions or crude cleaning tool. ÓÉÓÚÕôÆûÅç ìºíõôæû³ö Ú Ç³ ÈÈ Ó ±ÜÃ⽫ÕôÆûÅç ì ³ ½Ó µ½µäî»öã ÒÔÃâÅç³öµÄÕôÆû ɽ µ¼öâììéëê¹óãõ ÓÉÓÚÕôÆûÅç ìºíõôæû³ö Ú Ç³ ÈÈ Ó ±ÜÃ⽫ÕôÆûÅç ³ ½Ó µ½µäî»öã ÒÔÃâÅç³öµÄÕôÆû ɽ µ¼öâììéëê¹ó Page 3 6kw & above:3/4'')

6 G08 Important: 1.Please consult your distributors of building materials like acryl, fiber glass or other anti-heat sheet about the installation position of steam nozzle. It is suggested that M anti-heat material can be used..in the entire steam room, it is required that steam can not leak out. The pipes, its accessories and the holes in the wall should be airproof by applying airproof glue so that no steam will enter the holes in the wall. Airproof green material belt If non-heat-resistant material like acryl is used as building material, reserve a gap no smalle3rthan 1/4'' and fill with heat-insulated material. Use airproof silicon gel or corresponding airproof material to fill in the gaps in the wall to achieve the waterproof and damp-proof effect. Inside wall in the steam room Drainpipe (1/'') According to national or local rules, the steam engine drainage valve should be equipped with drainpipe. The steam engine drains the water by using weight. Attention: water. the drainpipe should not incline upwards so as to facilitate the drainage of afety valve 1.afety valve is a piece of safe equipment in order to prevent too much steam pressure in the interior steam engine due to various reasons..the pressure limit range of safety valve is 15PI and the pressure will begin to decrease if pressure should come over this value. 3.If it is allowed by local codes, provide the safety valve with exterior drainpipe. Warning: 1.Do not dismantle the pressure decrease valve at random in case any danger should happen..to maintain the proper and automatic operation of safety valve, make sure the safety valve connection pipe is smooth. Page 4

7 G08 print for the steam engine 14mm 43mm 395mm 304mm team outlet 06mm 188mm 151mm 3mm 6mm 7mm afety valve Water inlet Water drainage 66mm 30mm Fuse for wire power supply Power wire hole Controller wire and light wire hole Fuse for wire power supply team outlet afety valve 370mm Water inlet 180mm 30mm 60mm Water drainage 30mm 100mm 160mm 400mm Fuse for wire power supply Power wire hole Controller wire and light wire hole Fuse for wire power supply Page 5

8 G08 34mm 535mm 435mm team outlet 73mm 183mm 34mm afety valve Water inlet Water drainage 350mm 385mm Fuse for wire power supply Power wire hole Controller wire and light wire hole Fuse for wire power supply Attention: To facilitate maintenance, keep the steam engine clean. If the information provided is limited, do not operate on the pipeline and electric equipment arbitrarily as shown in the figure for proportion. Caution: To avoid damage to the equipment, do not connect strong electric current directly to the components. Electrical requirements: Electricity supply circuitry: 1.Test the voltage of electricity supply and make sure steam engine with suitable electric voltage should be used..insulated copper wire should be used with an anti-heat temperature of 90 and a specified voltage of 500V. Refer to national or local electricity consumption code for the specifications. Refer to the ammeter for the ampere. 3.Choose steam engine with suitable item number, and plug the ground wire into the ground terminal. 4.Install an independent circuit breaker between the power supply and the steam engine so as to provide an electricity supply with overflow protection and electricity leakage protection. Attention: All the connection must be in accordance with national and local electricity consumption code and be installed by professional electricians. Page 6

9 G08 Ampere Meter Type Applicable space 3 of the room (m ) Electricity supply Max.Electri c current (A) pecifications for power wire (AWG) G08-3kW G08-4.5kW 0-40V~(1PH/PH) 0-40V~(1PH/PH) 13.7A 0.5A 1# or.0mm 1# or 4.0mm G08-6kW 0-40V~(1PH/PH) 08V~ 3PH 7.3A 16.7A 10# or 6.0mm 1# or 4.0mm V~ 3PH 9A 1# or.0mm 0-40V~(1PH/PH) 34A 8# or 6.0mm G08-7.5kW G08-9kW G kW G08-1kW G08-15kW G08-18kW 08V~ 3PH V~ 3PH 0-40V~(1PH/PH) 08V~ 3PH V~ 3PH 0-40V~(1PH/PH) 08V~ 3PH V~ 3PH 0-40V~(1PH/PH) 08V~ 3PH V~ 3PH 08V~ 3PH V~ 3PH 08V~ 3PH V~ 3PH 1A 11.4A 41A 5A 13.7A 48A 9A 16A 55A 33.3A 18.A 4A.8A 50A 7.3A 10# or 4.0mm 1# or.0mm 8# or 8.0mm 1# or 4.0mm 1# or.0mm 8# or 8.0mm 8# or 6.0mm 1# or 4.0mm 6# or 10.0mm 8# or 6.0mm 1# or 4.0mm 6# or 8.0mm 1# or 4.0mm 6# or 10.0mm 10# or 6.0mm The data provided above are for 0-40V(1PH/PH) and 08V(3PH) and V(3PH). Within the eyeshot of the steam engine, install an independent circuit breaker so as to provide an electricity supply with overflow protection and electricity leakage protection. Page 7

10 G08 Assembly graph for power wire Attention: To avoid the damage to the equipment, do not connect strong electric current to the component directly. Warning: This graph is for explanation only. For actual installation, refer to national and local electricity consumption codes by professional electricians. Power connection terminal L1 L L1 L L3 L1 L (3-1kW) (0-40V~ PH) L1 L L3 (6-18kW) (08V~ 3PH) Power connection terminal Power connection terminal L N L1 L L3 N L1 L L3 N L N (3-1kW) (0-40V~ 1PH) L1 L L3 N (6-9kW) ( V~ 3PH) L1 L L3 N ( kW) ( V~ 3PH) Page 8

11 G08 Wiring Diagram V(3PH) upply Water Level ensor (hort Pin) (Long Pin) J J1 J1-1 N L3 L L1 J-1 J- G J1- /Green G08-6kW/7.5kW/9kW V~ 3PH upply Water Level ensor (hort Pin) (Long Pin) J J1 J1-1 N L3 L L1 G /Green J-1 J- J1- Water Level ensor (hort Pin) (Long Pin) G kW/1kW/ 13.5kW V~ 3PH J1 J J3 J3- upply N L3 L L1 J3-1 J- G /Green J-1 J1- J1-1 G08-15kW/18kW V~ 3PH Page 9

12 G08 Wiring Diagram 08V (3PH) Water Level ensor (hort Pin) (Long Pin) J3 J J1 J- upply L3 L L1 G /Green J1-1 J1- J3-1 J-1 J3- G08-15kW/18kW 08V~ 3PH upply Water Level ensor (hort Pin) (Long Pin) J J1 J-1 L3 L L1 G /Green J1- J1-1 Water Level ensor (hort Pin) (Long Pin) G08-6 kw/9kw 08V~ 3PH J3 J J1 J3- J- J1-1 upply L3 L L1 G /Green J1- J-1 J3-1 G kW/1kW/13.5kW 08V~ 3PH Page 10

13 G08 Wiring Diagram 0-40V(1PH/PH) upply Water Level ensor (hort Pin) (Long Pin) J1 J1-1 L N L1 L G /Green J1- Water Level ensor (hort Pin) (Long Pin) G08-3kW 0-40V~ 1PH/PH J1 J1-1 L N upply L1 L G J1- /Green Water Level ensor (hort Pin) (Long Pin) G08-4.5kW 0-40V~ 1PH/PH J1 J J-1 J- upply L N L1 L G J1- /Green J1-1 G08-6kW/7.5kW/9kW 0-40V~ 1PH/PH Page 11

14 G08 upply Water Level ensor (hort Pin) (Long Pin) J3 J J1 J1-1 J-1 J3-1 L N L1 L J3- G J- /Green J1- Installation of the top light CAUTION: G kW/1kW 0-40V~ 1PH/PH is available in 1V/0V/30V outputs. Before connect to the light, please consult with manufacturer to know what voltage the light is, so as to avoid generator damage or cause danger. If the light output is 1V, the power of the light should not be more than 35W,othwise,transformer will be burned and cause danger. If light input is 0v~40V,light power should not more than 100W. The light should be installed on the top of the steam room or the places where are not access to the children. CAUTION: Take some moisture proof measures in process of installation. Can not let the electrical components be exposed to moisture or, it will cause damage or short circuit. The steam control panel (Possible location) The steam outlet The spare place under the wash pan possible location The steam generator CAUTION: The illustration is just for explaination, the practical installation must comply with the nation's electric criterion,and processed by the professional electrician. Page 1

15 G08 Choose your type of machine Measure the length, width and height (foot) of the current steam shower or bathtub room. Example; L:7xW:5xH:8 = 80 Cubic Feet You would need Model s-900(it is that simple) However,if you shower materials are; A:Natural tone(granite or Marble etc.) ADD 75% B:Exterior walls ADD 5% C:Celia Heights exceeding 8 FT. ADD 5% D:Ceramic tile ADD 75% E:Glass( walls) ADD 75% Important: The calculation formula for selecting the type of steam engine is for reference only. Due to the variability of the building, the specifications and size illustration are used as guidelines only. If we have complete information, including actual blueprint, project instruction and building details, we can select the type of machine once again. Otherwise, the manufacturer will not be responsible for the selection of the type of machine. Maintenance of the steam engine Important: Perform water discharge operation after each use. 1. Wait for the completion of automatic water discharge after each time of using the steam engine to make sure the water in the tank is discharged completely before cutting off power supply.. There should not be any leakage or damage among the steam engine, steam nozzle, components and pipes. They should be checked and repaired annually. 3. Clean the water supply pipes of the steam engine once a year. 4. Check all the connections, faucets and connection terminal to see whether they become loose or are damaged due to overheat. 5. Check the furring accumulated in the water tank and electric heating tube. If the furring is thick, dispose it in time (use diluted lemon acid to soak for minutes). 6. Remove the water level sensory needle once a quarter to clean the furring in the needle. Page 13

16 G08 Configuration of steam generator Exclosure Insulation bracket 3 Circuit board 4 team Outlet 5 Pressure relief valve 6 Water fill valve 7 Water drain valve 8 ubsidiary water tank 9 Main water tank 10 Heating Element 11 1 O 105 C Hi-limit Transformer Terminal block Fuse Earth wire connector 16 Relay Water level sensor O 105 C Hi-limit Page 14

17 G08 Common troubles trouble shooting methods To facilitate your use and maintenance of sauna room, the following common troubles trouble shooting methods are listed for identification. Troubles Causes of troubles Trouble-shooting methods The machine does not start when electrified Electricity leakage switch breaks automatically When the machine is started, hot water comes out with little or no steam The display screen on the control panel does not display 1.The fuse is burned..the wire connection terminal becomes loose. 3.Not good contact in the connection wire between the controller and the steam engine. 1.The wire connector is dampened or damaged..the heating tube breaks 1.Change the fuse (on the shell 0.8A/ 50V).Plug tight the wire connection terminal 3.Make sure the steam engine and the controller come into good contact 1.Check whether the wire connector is dampened or damaged, and dry with dryer if dampened..change a heating tube. 1. The water drainage valve is broken. 1. Change a water drainage valve. 1.The power wire is not connected well or not in good contact. The connection plug between the control panel and the electrically-controlled box becomes loose..trouble with plugboard. 1.Check whether the connection plug between the control panel and the electricallycontrolled box has become loose, and whether the power circuitry has good contact..change a plugboard. Water leakage No steam when starting the machine The steam does not come out, the water sounds in the machine The light can not be turned on The display box displays normally with no steam input 1.The water pipe connector becomes loose or the pipe breaks.water leakage in the water input valve or the waterdrainage valve 1.No electricity..no water. 3.The set temperature is too low 4.Troublewithwire. 1. The steam pipe is jammed. 1. The fuse is burned.. The light is broken 3. The wire is broken 4. The plug does not have good contact 1.Too much pressure inside the steam engine, so the system breaks for heat protection..wire is broken for heat protection. 1.Tighten the loose connector, and change the broken pipe..change the water input valve or the water drainage valve. 1.Check the power supply.check the water input pipe and water input valve 3.Reset the temperature 4.Contact the distributor 1. Cut power supply to check whether the steam pipe is smooth. 1.Change the fuse (on the shell 1A/50V). Change a light bulb. 3. Change wire. 4. Make the contact good. 1.Check the steam transport pipe and restore automatically after heat protection becomes cool..check the heat protection wire to make sure the connection is good. Page 15

18 G08 Important: The list above is for reference only. In actual checking and repairing, based on the national and local codes, ask professional service personnel to operate. Technical parameter TYPE G08 Applicable space 3 of the room (m ) Important: The parameter listed in the table will be varied from different place and temperature,please consultate to the qualificatory designer and architect for the more detailed use. Page 16