ELECTRIC PASTA COOKERS

Transcription

1 OPTIMUM 700 & 900 ELECTRIC PASTA COOKERS BUILDER S SPECIFICATIONS Part A: Technical characteristics Part B: Technical instructions for the installer - WARNING - Installation and repairs must be carried out by personnel approved by the manufacturer and in accordance with current regulations and standards. If any modifications are made the manufacturer can accept no responsibility whatsoever. These appliances must be used in a well-ventilated area. Read the notice carefully before installation. When handling it, it is imperative to leave the appliance on its base till final installation. 3BE390723NI

2 Page 1 3BE390723NI 11/09 TABLE OF CONTENTS ELECTRIC PASTA COOKERS A) TECHNICAL CHARACTERISTICS... 2 B) TECHNICAL INSTRUCTIONS FOR THE INSTALLER 1. FIRM PLATES PLATE LOCATION OF THE PLATE INSTALLATION: GENERALITIES GENERAL REQUIREMENTS HANDLING UNPACKING ACCESS TO THE COMPONENTS PLACED BEHIND THE FASCIA INSTALLATION: PUTTING IN PLACE ASSEMBLY OF CANTILEVER APPLIANCES TO A WALL ASSEMBLY OF APPLIANCES TO AN INDIVIDUAL BASE ASSEMBLY OF APPLIANCES ON A COMMON BASE ASSEMBLY OF APPLIANCES ON A MASONRY BASE INSTALLATION: CONNECTIONS ELECTRIC CONNECTION WATER CONNECTION DRAINAGE CONNECTION

3 Page 2 3BE390723NI 11/09 A: TECHNICAL CHARACTERISTICS OPTIMUM 700, Electric pasta cooker P ELECTRIC connection (Foresee a cable with 1.5 m free length) HOT WATER DRAINAGE MODEL B-B709.CP400 DIMENSIONS (mm) Width 400 Depth x Height 730 x 959 Basket 90 x 280 x 160 CAPACITIES (mm) Tank (litres) 20 Basket (kg) 0.5 PACKAGING (mm) Width 500 Depth x Height 830 x 1150 WEIGHT (KG) 70 ELECTRICITY (Three-phase 230V+T or 400V+N+T) Power (kw) 230V 3a.c V 3Na.c. 9 Max. intensity (A) 230V 3a.c V 3Na.c. 13 HOT WATER Pressure 2.5/6 bars Water hardness 70 ppm Max. temperature 60 C Connection Hose 20/27 (3/4 ) DRAINAGE Connection Diameter 28 SAFETY OPERATION Heating with no water TYPE OF APPLIANCE Back to the wall or another appliance ELECTRIC CONNECTION Electric outlet at 390 mm above the floor. This document is not contractual; Edition 11/2009 3BE0584FT

4 Page 3 3BE390723NI 11/09 OPTIMUM 900, Electric pasta cooker P ELECTRIC connection (Foresee a cable with 1.5 m free length) HOT WATER DRAINAGE MODEL B-B909.CP400 DIMENSIONS (mm) Width 400 Depth x Height 920 x 959 Basket 90 x 280 x 160 CAPACITIES (mm) Tank (litres) 20 Basket (kg) 0.5 PACKAGING (mm) Width 500 Depth x Height 1030 x 1150 WEIGHT (KG) 55 ELECTRICITY (Three-phase 230V+T or 400V+N+T) Power (kw) 230V 3a.c V 3Na.c. 9 Max. intensity (A) 230V 3a.c V 3Na.c. 13 HOT WATER Pressure 2.5/6 bars Water hardness 70ppm Max. temperature 60 C Connection Hose 20/27 (3/4 ) DRAINAGE Connection Diameter 28 SAFETY FUNCTIONING Heating without water TYPE OF APPLIANCE Back to the wall or another appliance ELECTRIC CONNECTION Electric outlet at 390 mm above the floor. This document is not contractual; Edition 11/2009 3BE0585FT

5 Page 4 3BE390723NI 11/09 1. FIRM PLATE 1.1 PLATE Firm plate In any correspondence about your equipment, please indicate: - The model number (Model.) - The serial number (Fab.Nr.) - The date (Date). 1.2 LOCATION OF THE FIRM PLATE The firm plates are fixed on the control board (see the diagrams hereafter). Location of the firm plate

6 Page 5 3BE390723NI 11/09 2. INSTALLATION: GENERALITIES NATURE AND POSITION OF THE CONNECTIONS See the "Technical characterisitcs" at the beginning of these instructions. 2.1 GENERAL REQUIREMENTS A qualified engineer must carry out the installation, modification or repair of the appliance in a workmanlike manner. These appliances must be installed with sufficient ventilation to prevent the formation of excessive concentrations of substances noxious for the health in the room in which they are installed. The equipment is not designed to work in an explosive atmosphere. Due to this, it must not be installed in a zone subject to ATEX directive. The appliances must be installed according to the standard EN 1717 and the national regulation in force relating to water. These units must only be placed against a wall or a partition. The latter must be of non-combustible materials or, if not, must be covered with an appropriate, good insulating and non-combustible material. The manufacturer certifies that the packaging meets the provision 94/62/CE (provision relating to packagings and packaging waste of ) and requests that final installer (and user) observes the rules relating to the removal of the packaging (recycling or reconditioning). 2.2 HANDLING The appliance should only be handled with adapted lifting equipment. Should the appliance need to be transported, this must be on its original pallet and it must not be stacked on other appliances under any circumstances. If the appliance is to be moved without its pallet, it should be carried and not pulled. 2.3 UNPACKING Before installation, remove the strapping from the appliance. The individual parts are not bolted down. Remove the protective plastic film from the stainless steel parts before heating.

7 2.4 ACCESS TO THE COMPONENTS PLACED THE FASCIA Page 6 3BE390723NI 11/09 - Unscrew both M5 x 16 screws under the fascia. - Tilt the fascia: Slightly pull downwards 1 then to yourself Put the fascia in locking position: clamp both lugs into the apertures foreseen in the fascia.

8 Page 7 3BE390723NI 11/09 3. INSTALLATION: PUTTING IN PLACE 3.1 ASSEMBLY OF CANTILEVER APPLIANCES TO A WALL Drilling pattern The fixation of a bracket must support a tensile strength of 400 dan (2 brackets for a 400, 800, 1000 or 1200 wide appliance). It is recommended, for the fixation of cantilever appliances to a concrete wall, to observe the following points: * The reinforced concrete of the wall must be at least of quality 23 MPA (DTU). * Use HSA-R M 8x75 plugs or equivalent (2 for cooking tops and 6 for cooking units). * For the plugs above, each hole must be drilled to diameter 8 mm and, at least, 65 mm deep. Procedure - Fix the lower bearing beam of the appliances against the wall. Warning! Check this bearing beam is properly horizontal. - Fix the template supplied by two 5 screws to the wall. Check horizontality

9 Page 8 3BE390723NI 11/09 - Drill through the 5 fixation holes of the brackets. Use the upper holes (2 brackets per appliance). Note: In case of impossibility (due to the presence of technical ducts, a metal strengthener in the wall ), drill through the lower holes in the template. - Remove the template. - Increase the bracket fixation holes to diameter 8 and, at least, to 65 mm in depth. - Fix the brackets to the wall. Use HSA-R M 8x75 plugs or equivalent. - Open the brackets to the maximum by means of the centre screw Opened bracket Fixation screw Opening screw - Put the appliances in place on the brackets and lock them. Warning! The appliances must rest on the bearing beam. Bracket Bearing beam

10 Page 9 3BE390723NI 11/09 - Fix the appliances between themselves from behind in the way of collectors by one HM5 X 16 screw + ø 5 flat washer. - Fix the appliances between themselves from the front after having removed the front fascia (see paragraph 3.4) with one HM5 X 16 screws + Ø 5 flat washers. 3.2 ASSEMBLY OF THE APPLIANCES ON AN INDIVIDUAL BASE - Fix the appliances between themselves at the back in the way of collectors by one HM5 X 16 screw + ø 5 flat washer. - Fix the appliances between themselves at the front after having removed the front fascia (see paragraph 3.4) with one HM5 X 16 screws + Ø 5 flat washers.

11 3.3 ASSEMBLY OF THE APPLIANCES ON A COMMON BASE Page 10 3BE390723NI 11/09 - Put an appliance on the base, the back parts of the appliance and the base being approximately in alignment. (The base is is symmetrical, the back and front parts being identical). - Push the appliance backwards until the hooks made in its bottom slots into the square holes size 25 x 25 foreseen for this purpose. Hook fixation (detail) Hook Hole - Perform these two operations for each appliance put on the same base. - From front, fix the appliance on the base with two HM 5 x 16 screws + 2 ø 5 flat washers from the underside. - Fix the appliances between themselves at the back in the way of collectors with one HM5 X 16 screw + Ø 5 flat washer. - Fix the appliances between themselves at the front after having removed the front fascia (see paragraph 3.4) with one HM5 X 16 screws + Ø 5 flat washers.

12 3.4 ASSEMBLY OF THE APPLIANCES ON A MASONRY BASE Dimension of the masonry base for wall or central stove Page 11 3BE390723NI 11/09 Wall (side view) Centrally (side view) Stove depth Stove depth Stove depth Am Ac Finished Full tiled base height with tiled front Full tiled base Full tiled base 1 cm/m maximum slope 1 cm/m maximum slope 1 cm/m maximum slope Finished height with tiled front (front view) Lf: Stove width Ls Full tiled base Range Am Base depth as a wall version Dimension of the base Ac Ls Base depth as a central Base length version Finished height, completely tiled on the front Optimum Lf Optimum Lf The technical compartment is compulsory if the switch-off tap, the shut-off valve, or the reducing valve are in the stove. There are two possibilities: 1) Neutral top on a 200 or 400 wide technical compartment. 2) Cupboard foreseen for taps and sized 400 with all possibilities of cooking or neutral tops except induction.

13 Assembly of the appliances on a masonry base Page 12 3BE390723NI 11/09 Possibility to lay piping on the front Appliance Base space 2000 Trimming plinth Ventilation Base height at front Put the appliances in place on the masonry base. Note: If the appliances are delivered separately from the base, install the appliances on one or more bases space Connect electrical supply to the appliances (see paragraph 5: Installation: Connections) Assemble the appliances between themselves. - Fix the appliances between themselves at the back in the way of collectors with one HM5 X 16 screw + Ø 5 flat washer. - Fix the appliances between themselves at the front having removed the fascia (see paragraph 2.2.3) with two HM5 X 16 screws + Ø 5 flat washers. Connect gas, water and drainage lines to the appliances. Fit the trimming plinths. One front plinth per space 2000 base and one right and left end trimming plinth per stove, depending on order. - Assemble one or more front plinths with junctions (depending on the quantity of bases) (2 screws per plinth). - Fix one or more front plinths 1 and 2) onto one or more bases (two screws at least per plinth). - Fix the back part (on the end appliances before their final installation) on the base with the hex head screw (3). - Fix the right and left end trimming kits (4) (2 front screws and 1 back screw)

14 4.1 ELECTRIC CONNECTION Page 13 3BE390723NI 11/09 4. INSTALLATION: CONNECTIONS Location of the equipotentiality terminal Electric connection is carried out from behind of the appliance, whatever the model. - Loosen the fixation screw and remove the cover of the connecting box. - Introduce the cable through the gland. - Tighten the gland. - Connect the wires. - Put the cover back in place and fix it. - Connect the equipotential link to the terminal foreseen for the purpose. Only use supply cables of the H07 RN-F type with section : Voltages Sections 230 V 3 a.c. 4 x 4 mm V 3N a.c. 5 x 2.5 mm 2 Foresee an omnipolar shut off device patented for safety of personnel (with a distance between contacts of at least 3 mm when opened). The installation must meet the national rules in force (France: NFC ). The appliance must be connected to the earth. The different electric appliances must also be connected by means of an equipotential line (all metallic structures to the same voltage) by means of a terminal provided for this purpose and located beside the connecting gland. The builder denies all responsibility in the case where the instructions above are not observed.

15 Page 14 3BE390723NI 11/ WATER CONNECTION - Hot water. - Minimum pressure 2.5 bars, maximum 6 bars. - Maximum temperature for hot water 60 C. - Connection of flexible hose of diameter 15/21 (1/2"). - Foresee a shut off valve in the vicinity. 4.3 DRAINAGE CONNECTION Drained water is at a temperature of 100 C, due to this exclude the PVC-type materials. Foresee piping depending on the reservation 50 mm minimum IMPORTANT: In the framework of protection against pollution of mains water, IT IS STRICTLY PROHIBITED TO CONNECT THE APPLIANCE DIRECTLY TO THE OUTER SEWAGE SYSTEM (in a tight manner). So as to avoid any rise of sewage water into the enclosure of the recipient, a vent to open air must be foreseen between the drainage system of the appliance and the outer sewage line. The drain must include a siphon to fight against any return of bad smells. Recommended solution: 50 mm Ø100 siphon type plug (under the slab) or gutter