Container Refrigeration

Transcription

1 Container Refrigeration SERVICE PARTS LIST for 69NT to 25 Container Refrigeration Units T--27PL Rev E

2 SERVICE PARTS LIST CONTAINER REFRIGERATION UNIT MODEL 69NT to 25

3 TABLE OF CONTENTS QUICK LIST -- CLAMPS, FILTER--DRIER, FUSE, TY--WRAPS, WIRE TERMINALS... 2 REFRIGERATION UNIT ASSEMBLY REFRIGERATION UNIT -- AREA LOCATOR RAIN GUTTERS HANDLES THERMOMETER PORT CONTROL BOX DOOR -- LCD AND LED DISPLAYS CONTROL BOX CONTROL BOX -- STD ELECTRICAL COMPONENTS, RM, CFS, EBS CONTROL BOX -- CONTROLLER MODULE AND SOFTWARE CARDS CONTROL BOX -- DISPLAY MODULE AND COMMUNICATIONS INTERFACE MODULE 2.0 CONDENSER FAN MOTOR AND COIL CONDENSER FAN GRILLE ASSEMBLY COMPRESSOR TUBING RECEIVER WATER--COOLED CONDENSER ECONOMIZER, EXAPANSION VALVE, SOLENOID VALVE ANDFILTER DRIER SRS AND STS EVAPORATOR FAN ASSEMBLY UPPER FRESH AIR MAKE--UP AND ACCESS PANEL LOWER FRESH AIR MAKE--UP VENT EVAPORATOR COIL -- REAR PANELS REMOVED USDA BACK PANEL ASSEMBLY -- OPTION -- ALUMINUM BOLTED OPTION 7 AND OPTION 8 -- ELECTRONIC PARTLOW TEMPERATURE RECORDER COMPRESSOR MOUNTING COMPONENTS AND GUARD TRANSDUCERS CABLE RESTRAINT COMPONENTS VOLTAGE CABLES AUTOTRANSFORMER KIT LABELS AND DECALS (Not Applicable to All Units) INTERROGATOR AND ACCESSORIES DATAVIEW/DATAREADER INTERROGATOR RECEPTACLE... 5 COMPRESSOR CONTROLLER/DATACORDER CONFIGURATION TOOLS i

4 INTRODUCTION INTRODUCTION The Carrier Transicold model 69NT0-55 series units are of lightweight aluminum frame construction, designed to fit in the front of a container and serve as the container front wall. 2 CONFIGURATION IDENTIFICATION Unit identification information is provided on a plate located near the compressor. The plate provides the unit model number, the unit serial number and the unit parts identification number (PID). The model number identifies the overall unit configuration while the PID provides information on specific optional equipment, factory provision to allow for field installation of optional equipment and differences in detailed parts. Configuration identification for the models covered herein is provided in the Carrier Transicold Container Unit Matrix at OPTION DESCRIPTIONS Various options may be factory or field fitted to the base unit. These options are listed in the tables and described in the following subparagraphs.. Battery The refrigeration controller may be fitted with standard replaceable batteries or rechargeable battery pack..2 Dehumidification The unit may be fitted with a humidity sensor. This sensor allows setting of a humidity set point in the controller. In the dehumidification mode the controller will operate to reduce internal container moisture level.. Control Box The control box is composite material and may be fitted with a lockable door.. Temperature Readout The unit may be fitted with suction and discharge temperature sensors. The sensor readings may be viewed on the controller display..5 Pressure Readout The unit is fitted with standard suction and discharge transducers. The transducer readings may be viewed on the controller display..6 USDA The unit may be supplied with fittings for additional temperature probes which allow recording of USDA Cold Treatment data by the integral DataCORDER function of the Micro-Link refrigeration controller..7 Interrogator Units that use the DataCORDER function are fitted with interrogator receptacles for connection of equipment to download the recorded data. Two receptacles may be fitted, one accessible from the front of the container and the other mounted inside the container (with the USDA receptacles)..8 Remote Monitoring The unit may be fitted with a remote monitoring receptacle. This item allows connection of remote indicators for COOL, DEFROST and IN RANGE. Unless otherwise indicated, the receptacle is mounted at the control box location..9 Communications The unit may be fitted with a communications interface module. The communications interface module is a slave module which allows communication with a master central monitoring station. The module will respond to communication and return information over the main power line. Refer to the ship master system technical manual for further information..0 Compressor The unit is fitted with a scroll compressor with either standard piping (equipped with suction, discharge, economizer and oil return service valves) or with semi-hermetic piping (equipped with suction, discharge and economizer service connections).. Condenser Coil Theunitisfittedwitharowcoilusing7mmtubing..2 Autotransformer An autotransformer may be provided to allow operation on 90/20, phase, 50/60 hertz power. The autotransformer raises the supply voltage to the nominal 80/60 volt power required by the base unit. The autotransformer may also be fitted with an individual circuit breaker for the 20 volt power. If the unit is fitted with an autotransformer and communications module, the autotransformer will be fitted with a transformer bridge unit (TBU) to assist in communications.. Temperature Recorder The unit may be fitted with an electronic recorder manufactured by Partlow Corporation.. Gutters Rain gutters may be fitted over the control box and recorder section to divert rain away form the controls. The different gutters include standard length bolted gutters, extended length gutters and riveted gutters. i

5 .5 Handles The unit may be fitted with handles to facilitate access to stacked containers. These handles include fixed handles (located at the sides of the unit) and/or a hinged handle at the center (attached to the condenser coil cover)..6 Thermometer Port The unit may be fitted with ports in the front of the frame for insertion of a thermometer to measure supply and/or return air temperature. If fitted, the port(s) will require a cap and chain..7 Water Cooling The refrigeration system may be fitted with a water cooled condenser. The condenser is constructed using copper-nickel tube for sea water applications. The water cooled condenser is in series with the air cooled condenser replaces the standard unit receiver. When operating on the water cooled condenser, the condenser fan is deactivated by either a water pressure switch or condenser fan switch..8 Back Panels Back panel designs that may be fitted include panels of aluminum and stainless steel. Panels may be fitted with access doors and/or hinge mounting Volt Cable Various power cable and plug designs are available for the main 60 volt supply. The plug options tailor the cables to each customers requirements Volt Cable Units equipped with an autotransformer require an additional power cable for connection to the 20 volt source. Various power cable and plug designs are available. The plug options tailor the cables to each customers requirements..2 Cable Restraint Various designs are available for storage of the power cables. These options are variations of the compressor section front cover..22 Upper Air (Fresh Air Make Up) The unit may be fitted with an upper fresh air makeup assembly. The openings may also be fitted with screens..2 Lower Air (Fresh Air Make Up) The unit may be fitted with a lower fresh air makeup assembly. These assemblies are supplied in two designs, the standard design and the macro design. The openings may also be fitted with screens..2 Evaporator The unit is fitted with an evaporator coil and a hermetic thermal expansion valve..25 Evaporator Fan Operation The units are fitted with normal evaporator fan operation. Opening of an evaporator fan internal protector will shut down the unit..26 Labels Operating Instruction and Function Code listing labels will differ depending on the options installed. For example, additional operating instructions are required to describe start-up of a unit equipped with an autotransformer. Labels available with additional languages are listed in the parts list..27 Plate Set Each unit is equipped with a tethered set of wiring schematic and wiring diagram plates. The plate sets are ordered using a seven digit base part number and a two digit dash number. (See Unit Matrix).28 Controller Two different controllers are available:. Remanufactured - Controller is the equivalent of a new OEM controller and is supplied with a 2 month warranty. 2. Repaired - Controller has had previous faults repaired and upgraded with the latest software. Note: Repaired controllers are NOT to be used for warranty repairs only full OEM Remanufactured controllers are to be used. Controllers will be factory equipped with the latest version of operational software, but will NOT be configured for a specific model number and will need to be configured at the time of installation or sale..29 Stepper Drive All the units covered by this manual have suction modulating valves which act to control system capacity. Units indicated as being fitted with stepper drive have digital control motors fitted to the suction modulating valve to open and close the valve in steps as required..0 Condenser Grille Two styles of condenser grilles are available: direct bolted grilles and hinged grilles. ii

6 OPTION LEGEND General - Feature Not Applicable X P Features that apply to model Factory Installation of Equipment to Allow Field Installation AutoTransformer Codes Transformer Fitted 2 Transformer With CB2 Fitted Transformer With CB2 and Transformer Bridging Unit Transformer With CB2 and Receptacle Back Panel Codes Bolted Panels Battery Codes S R Standard (Disposable) Cells Rechargeable Cells Rechargeable Cells -- Secure Location Cable Guard Codes Standard Cable with Receiver 2 Standard Cable with Full Guard Transicord Cable with Full Guard Transicord Cable without Receiver 5 Standard Cable with Receiver, Orange Cable Restraint Codes 2 Left Bungy Cord Only J--Hook R Communications Codes Dummy Receptacle 2 HighDataRate Low Data Rate Compressor Codes S SS Condenser Grille Codes B H Condenser Codes Scroll Scroll with Semi-Hermetic Piping Bolted Grille Hinged Grille Four Row Coil Control Box Codes C Composite Box Without Door Lock CL Composite Box With Door Lock Control Box Door LCD Display 2 LED Display Emergency Bypass Codes B Emergency Bypass & Emergency Defrost EB Emergency Bypass Only Gutter Codes Standard Length Bolted Gutters Extended Length Gutters Rivieted Gutters Handle Codes 2 Two Side Interrogator Receptacle Codes Left Straight Mount Box Mount Left Mount 5 Left Angled Mount Label Codes English 2 English / Spanish 5 English / Traditional Chinese Lower Air Codes No Lower Fresh Air 2 Lower Fresh Air Installed Lower Fresh Air With Screen Installed Lower Fresh Air Installed With VPS Pressure Readout Codes T Factory Installed Pressure Transducers Temperature Recorder Codes 7 Standard Electronic Partlow 8 Special Electronic Parlow 9 No Temperature Recorder 0 Electronic Partlow (Both) iii

7 Thermometer Port Codes Supply Air Port 2 Return Air Port B Both Ports Upper Air Codes No Upper Fresh Air 2 Upper Fresh Air Installed Upper Fresh Air Installed With Screen Upper Fresh Air Installed With VPS USDA Codes D Option D V Option V Option 2 Option 2 20 and 60 Volt Cable Codes Option 2 Option 2 Option Option 5 Option 5 6 Option 6 7 Option 7 8 Option 8 9 Option 9 Water Cooling Codes W Water Pressure Switch F Condenser Fan Switch ORDERING INSTRUCTIONS All orders and inquiries for parts must include: Parts Identification Number (PID), Model Number, Unit Serial Number, Part Number, Description of part as shown on list and Quantity required. Address all correspondence for parts to the following address: CARRIER TRANSICOLD DIVISION Replacement Components Group, TR-20 P.O. Box 805, Syracuse, New York 22 or FAX to: (5) LETTER DESIGNATIONS The following letter designations are used to classify parts throughout this list: A/R = As Required N/A NS = = Not Available Not shown in illustration NSS PID = = Not sold separately - Order next higher assembly or kit. Parts Identification Number - essential to identify unit configuration. PL SST = = Purchase Locally Stainless Steel - 00 Series unless otherwise specified. SV = Suffix SV - added to part number designates service replacement part. iv

8 QUICK LIST - CLAMPS, FILTER -DRIER, FUSE, TY -WRAPS, WIRE TERMINALS PART NO. DESCRIPTION Clamp, Tube, / -- SST Clamp, Tube, /8 -- SST Clamp, Tube, /2 -- SST Clamp, Tube, 5/8 -- SST Clamp, Tube, / -- SST Clamp, Tube, 7/8 -- SST Clamp, Tube, --/8 -- SST Clamp, Tube, --/ -- SST Clamp, Tube, --/8 -- SST Clamp, Tube, --/2 -- SST Connector, Butt End, Wire Range to 6 AWG Connector, Butt End, Wire Range -- 6 to AWG Connector, Butt End, Wire Range -- 2 to 0 AWG Connector, Closed End, Wire Range to AWG Connector, Closed End, Wire Range -- 8 to 0 AWG SV Filter--Drier Fuse, 5 Amp (F & F2) Fuse, 0 Amp (FEB) Fuse, 7.5 Amp (FA & FB) Ring Terminal, #6, Wire Range -- 2 to 0 AWG Ring Terminal, #0, Wire Range -- 2 to 0 AWG Ring Terminal, /8, Wire Range -- 2 to 0 AWG Ring Terminal, /, Wire Range -- 2 to 0 AWG Ring Terminal, #0, Wire Range -- 6 to AWG Ring Terminal, 5/6, Wire Range -- 6 to AWG Ring Terminal, #0, Wire Range to 6 AWG Ring Terminal, /8, Wire Range -- 6 to AWG Spade Terminal, / X 5/6, Wire Range -- 6 to AWG Spade Terminal, /8, Wire Range -- 2 to 0 AWG Spiral Wrap, / Diameter X 25 Feet Long Spiral Wrap, /2 Diameter X 25 Feet Long 66U--80 Tube, Heat Shrink, / ID X 2--/8 Long 66U Tube, Heat Shrink, /2 ID X 2--/ Long Ty--Wraps, 5--/2 Inches Long Ty--Wraps,.00 Inches Long Series Wire Markers Sealant, Pipe (Used to seal fittings on unit with R--a) Cleaner, Coil Paint, One Coat, Compressor Paint, One Coat, 20 Compressors Paint, Two Coats, Compressor Paint, Two Coats, 20 Compressors

9 2 REFRIGERATION UNIT ASSEMBLY 2. REFRIGERATION UNIT - AREA LOCATOR , LOCATION 2

10 2. REFRIGERATION UNIT - AREA LOCATOR (Continued) Item Section Number Area Description Refer to Section 2.8 Upper Fresh Air Makeup and Access Panels 2 Refer to Section 2. Thermometer Port Refer to Section 2.29 Labels and Decals Refer to Section 2.7 Evaporator Fan Assembly 5 Refer to Section 2. Condenser Fan Grille Assembly 6 Refer to Section 2.0 Condenser Fan Motor and Coil 7 Refer to Section 2.9 Evaporator Coil 8 Refer to Section 2.2 Back Panels 9 Refer to Section 2.2 Rain Gutters 0 Refer to Section 2.20 USDA Refer to Section 2.9 Control Box 2 Refer to Section 2. Handles Refer to Section 2. Compressor Tubing Refer to Section 2.2 Transducers 5 Refer to Section 2.2 Compressor Guard 6 Refer to Sections 2.2 or Compressor 7 Refer to Section 2.5 Sensors -- SRS & STS 8 Refer to Section 2. or 2. Receiver or Water--Cooled Condenser 9 Refer to Section 2. Economizer and Filter Drier 20 Refer to Section 2.27 Power Cable 2 Refer to Section 2.27 Power Plug 22 Refer to Section 2.28 Autotransformer 2 Refer to Section Interrogator and Accessories 2 Refer to Section 2.2 Temperature Recorder 25 Refer to Section 2.9 Lower Fresh Air Makeup

11 2.2 RAIN GUTTERS 2 or or or OPTION - STANDARD LENGTH - BOLTED 69NT Gutter, Rain (Bolted, Standard - Right Side) 2 69NT Gutter, Rain (Bolted, Standard & Extended Length - Left Side) OPTION - EXTENDED LENGTH - BOLTED 2 69NT Gutter, Rain (Bolted, Standard & Extended Length - Left Side) 69NT Gutter, Rain (Bolted - Right Side) OPTION - RIVETED Gutter, Rain (Riveted - Right and Left Side) 2 2. HANDLES OPTION 2 - TWO SIDE 69NT5--8 Handle, Fixed 2

12 2. THERMOMETER PORT 2 OPTION - SUPPLY AIR PORT 66U Cap & Chain Assembly Label OPTION 2 - RETURN AIR PORT 66U Cap & Chain Assembly Label OPTION B - SUPPLY AND RETURN PORTS & 66U Cap & Chain Assembly 2 2& Label 2 5

13 2.5 CONTROL BOX DOOR - LCD AND LED DISPLAYS Control Box Control Box Door HINGE ASSEMBLY - SECTIONAL VIEW DOOR ASSEMBLY - PARTIAL BACK VIEW 6

14 2.5 CONTROL BOX DOOR - LCD AND LED DISPLAYS (Continued) OPTION - LCD DISPLAY 69NT Door Assembly, LCD Display, Includes: Gasket, Door SV Window and Gasket Assembly, Control Box Door -- Lexan Washer, Retaining -- SST U Screw, Retaining, Panel, SST 2 66U Screw, Retaining, Wing, SST Washer, Mylar, ID X OD Hinge, Half Hinge, Half Pin Assembly, with Tether Retainer, Nut Protector, Mylar (Hinge) U Screw, Truss Head, #0--2 X / Long -- SST 66U--5-- Washer, Lock, #0 -- SST 7 66U Washer, Flat, #0 -- SST Washer, Mylar, ID X OD Pocket, Placard Locknut, HXHD, # SST Rivet, Blind, /8 Diameter, Grip Range U Screw, #0--2 X /2 Long -- SST 20 66U Washer, Flat, #0 -- SST Door Strap Kit OPTION 2 - LED DISPLAY Door Assembly, LED Display, Includes: Gasket, Door 69NT Window Foam, Double Coated Washer, Retaining -- SST U Screw, Retaining, Panel, SST 2 66U Screw, Retaining, Wing, SST Hinge, Half Hinge, Half Pin Assembly, with Tether Retainer, Nut U Screw, Truss Head, #0--2 X / Long -- SST Washer, Lock, #0 -- SST 66U Washer, Flat, #0 -- SST Washer, Mylar, ID X OD Pocket, Placard Locknut, HXHD, # SST Rivet, Blind, /8 Diameter, Grip Range U Washer, Flat, #0 -- SST 7

15 2.6 CONTROL BOX In Box OPTIONC&CL -COMPOSITEBOX 8

16 2.6 CONTROL BOX (Continued) -- Plate, Schematic & Diagram (Refer to Container Unit Matrix) 2 66U--20 Screw, Truss Head, #0--2 X /2 Long -- SST 2 69NT Shield, High Voltage (Plastic) -- Includes: Hinge Rivet, Blind, /8 Diameter, Grip Range -- /8--/6 -- SST Stud & Retainer Package -- Includes: NS NSS Stud, Fastener NS NSS Retainer, Fastener Stud Fastener 8 69NT Shield, Low Voltage (Lexan) -- With Tether Label, Danger--High Voltage Control Box, Standard Composite 69NT Bracket, Non--Locking, White 69NT Bracket, Non--Locking, Orange 69NT Bracket, Locking (See Note ) Receptacle, Retaining Rivet, Blind, /8 Diameter, Grip Range - /6 - / Rivet, Blind, /8 Diameter, Grip Range - /8 - /6 (See Note 2) 2 66U--20 Screw, Truss Head, #0--2 X /2 Long -- SST 2 NS SV Crack, Chip and Hole Repair Kit NS SV Insert Repair Kit -- Includes: Insert X 9.9 mm (0.690 X 0.90 in) /--20 Threads -- NSS Insert X 6.5 mm (0.625 X in) 0--2 Threads -- NSS Insert X 7.5 mm (0.990 X in) 0--2 Threads -- NSS Insert X 9.5 mm (0.00 X 0.75 in) 0--2 Threads -- NSS Insert X 9.9 mm (0.500 X 0.90 in) /--20 Threads -- NSS Insert X 6.76 mm (0.75 X in) 0--2Threads -- NSS 0 NS Durabond Epoxy -- NSS NS Static Mixing Tube -- NSS NS Application Gun -- Required for Insert Repair NOTES. The bracket is bolted to the control box -- order 69NT for locking bracket. 2. When 69NT is used, , rivet, is to be used in the upper door location. 9

17 2.7 CONTROL BOX - SHIELDS REMOVED, STD ELECTRICAL COMPONENTS, RM, CFS, EBS OPTION F - CONDENSER FAN SWITCH Switch, Toggle (CFS) 2 66U Seal, Bushing Plate, Switch (with extra switch location) OPTION - NORMAL EVAPORATOR FAN OPERATION See Items 6 and 7 for contactor placement Contactor, Compressor (CH) (0 Amp) Screw, HXHD w/ Washer, #8-2 X 5/8 Long - SST Cover, Contactor Label, Contactor Contactors, (CF), (HR) & (EF & ES) (2 Amp) SV Panel, Contactor - Includes: Screw, HXHD, Captive Washer / -20 X 0.62 Long - SST 69NT Plate, Ground Pad, Key -- Includes: NSS Dot, Indicator (Green) -- See Note NSS Gasket (Between Key Pad and Key Pad Plate Assembly) Note: If unit is not already fitted with a green indicator dot (Item ) on the upper right corner of the control box door, install dot as illustrated

18 2.7 CONTROL BOX - SHIELDS REMOVED, STANDARD ELECTRICAL COMPONENTS (Continued) 5 NSS Plate Assembly, Key Pad Mounting Screw, Pan Head, #0--2 X / Long -- SST Washer, Plain, # SV Switch, Toggle (On -Off) 9 66U Seal, Bushing Switch, Toggle (MDS) (if equipped) Rivet, Blind, /8 Diameter, Grip Range - /6 - / Receptacle Plate, Switch SV Transformer, Base Unit 25 66U Screw, HXHD, #0-2 X /2 Long - SST A/R 26 66U Washer, Flat, #0 - SST A/R Contact, Auxiliary 28 66CH Trim, Flexible (85 Feet Long, Cut to Length) A/R Washer, Lock, #6 - SST 0 66U Circuit Breaker - 60 vac, 25 Amp (CB) 66U Screw, Pan Head, #6-2 X /8 Long - SST 2 69NT Bracket, Circuit Breaker Transformer, Current Sensing (CS) Screw, Captive Washer, #0-2 X 0.56 Long - SST 2 REMOTE MONITORING (STANDARD LOCATION) Plate, Switch, with RM Screw, Round Head, # -0 X 5/8 Long - SST 7 66U Washer, Flat, 0.25 ID - SST Nut, Self -Locking, # -0 - SST Receptacle, Remote Monitoring (RM) Plug, Remote Monitoring Cap and Tether, Receptacle Assembly 2 66U -685 Gasket, Remote Monitoring Receptacle REMOTE MONITORING (OPTIONAL LOCATIONS) Refer To Section.2 EMERGENCY BYPASS 66U Wire Tie Emergency Bypass Module Fuse (0A) Fuse Holder 2

19 2.8 CONTROL BOX - CONTROLLER MODULE AND SOFTWARE CARDS View - Back of Controller/DataCORDER 2

20 2.8 CONTROL BOX - CONTROLLER MODULE AND SOFTWARE CARDS (Continued) -- Module, Controller/DataCORDER -- RefertoSection5-- Includes: U Screw, HXHD, #0--2 X /2 Long -- SST 69NT Washer, Fender, 0.06 Thick -- SST Retainer, Screw, 0. ID Fuse, 7.5 Amp (FA & FB) Fuse, 5 Amp (F & F2) Label, Controller/DataCORDER Port xx/55 Card, Controller/DataCORDER Operation Software SV Connector (EC A--K) -- 0 Pin Socket, 20 AWG Socket, 8 AWG Plug, Sealing SV Connector (EC L--Y) -- 0 Pin Connector (KE) -- 5 Pin Connector (KB) -- 0 Pin NS Connector (KP) -- 9 Pin (Connects to Ribbon Cable) Connector (KD) -- Pin Connector (KC) -- 6 Pin Connector (KA) -- Pin Connector (MC) -- 8 Pin Connector (MA) -- 2 Pin Connector (MB) -- 6 Pin NS SV Battery, Real Time Clock, (Within the Controller) NS Wire Harness, Controller to Current Sensing Transformer) NS Wire Harness, Display Module to Controller/DataCORDER Module NS Label, Warning, Don t use ! --(Located on the control box behind the Controller/DataCORDER module.) NS Label, Warning, 55xx Series -- (Located on the high & low voltage shields) NS Label, Warning, 55xx Series -- (Located on the bottom panel of the control box between the Communications Interface module and the switch panel.) OPTION R - RECHARGEABLE BATTERY OPTION SV Controller/DataCORDER Module Rechargeable Battery Pack with Connector A/R OPTION S - STANDARD BATTERY OPTION Controller/DataCORDER Module Standard Battery Holder with Connector A/R OPTION - SECURE RECHARGEABLE BATTERY OPTION NOTE Controller/DataCORDER Module Rechargeable Battery Pack with Connector A/R NOTE Refer to technical manual for battery location.

21 2.9 CONTROL BOX - DISPLAY MODULE AND COMMUNICATIONS INTERFACE MODULE 2 MANUAL DEFROST/ INTERVAL

22 2.9 CONTROL BOX - DISPLAY MODULE AND COMMUNICATIONS INTERFACE MODULE (Continued) RP Module, LCD Display (Option ) RP Module, LED Display (Option 2) Screw, HXHD, #0--2 X /2 Long -- SST Connector (MK) -- 9 Pin Connector (MB) -- 6 Pin Connector (CIC) -- 7 Pin Connector (CIB) -- Pin Connector (CIA) -- 7 Pin NS Wire Harness, Key Pad to Display Module OPTION 2 - COMMUNICATIONS INTERFACE MODULE - HIGH DATA RATE SV Module, Communications Interface -- Includes: 9 66U Stud, Fastener, / turn, Long -- SST 0 66U Retainer, Push--on Screw, Captive Washer #0--2 X SST Retainer, Screw 0.75 OD 2 OPTION - COMMUNICATIONS INTERFACE MODULE - LOW DATA RATE SV Module, Communications Interface -- Includes: 9 66U Stud, Fastener, / turn, Long -- SST 0 66U Retainer, Push--on Screw, Captive Washer #0--2 X SST Retainer, Screw 0.75 OD 5

23 2.0 CONDENSER FAN MOTOR AND COIL 2 Option

24 2.0 CONDENSER FAN MOTOR AND COIL (Continued) OPTION - FOUR ROW (/8 ) CONDENSER COIL Fan, Condenser Label, CE Motor, Condenser -- Includes: Bearing Pin A/R Pin, Grounding A/R Nut, Self--Locking, 5/ Washer, Flat Washer, 0.75 ID X.000 OD 0 69NT5--62 Protector, Condenser Fan Motor Mounting 2 66U--56 Screw, Cap HXHD, 5/6--8 X NT5--52 Shim 69NT Shim 69NT Shim 5 69NT Shim Cover, Condenser Coil, Blue Includes: 69NT--8-- Cover, Condenser Coil, White Includes: Bumper (For Use with Uncoated Center Handles) A/R Plug (For Use with Coated Handles or Units with no Center Handle) A/R SV Coil, Condenser (Copper), --Row -- Includes Mylar Washers 20 69NT Protector (Apply Between Frame and Coil and Coil Cover) Protector,Mylar (Apply Between Coil and Coil Cover, RH and LH Sides) 2 7

25 2. CONDENSER FAN GRILLE ASSEMBLY OR OR BOLTED CONDENSER FAN GRILLE OPTION B HINGED CONDENSER FAN GRILLE OPTION H OPTION B - BOLTED CONDENSER FAN GRILLE, STANDARD PARTS Rivnut, /--20 A/R Washer, ID X.000 OD A/R 69NT Washer, Fender, / A/R Washer, Lock, / Spring A/R 5 66U Screw, Cap HXHD, /--20 X 0.75 A/R BLUE PANEL Grille and Venturi Assembly, Blue -- Includes: Panel Venturi Grille Assembly Rivet, Blind Label, Rotation WHITE PANEL Grille and Venturi Assembly, White -- Includes Panel Venturi Grille Assembly Rivet, Blind Label, Rotation ORANGE PANEL Grille and Venturi Assembly, Orange -- Includes Panel Venturi Grille Assembly Rivet, Blind Label, Rotation 8

26 2. CONDENSER FAN GRILLE ASSEMBLY (Continued) OPTION H - HINGED CONDENSER FAN GRILLE, STANDARD PARTS Rivet, Blind Protector Hinge Screw, HXHD, Sems #0--2 x 7/ Washer, Retaining, SST Washer, Mylar, / ID X.00 OD 5 69NT Washer, Fender, /, SST 2 BLUE PANEL WITH SLOTTED SCREW Use Standard Parts with Items Below: Grille and Venturi Assembly, Blue, Slotted Screw -- Includes Panel, Venturi Grille Assembly 8 66U Screw, Retaining, SST 2 WHITE PANEL WITH SLOTTED SCREW Use Standard Parts with Items Below: Grille and Venturi Assembly, White, Slotted Screw -- Includes Panel, Venturi Grille Assembly 8 66U Screw, Retaining 2 ORANGE PANEL WITH SLOTTED SCREW Use Standard Parts with Items Below: Grille and Venturi Assembly, Orange, Slotted Screw -- Includes Panel, Venturi Grille Assembly 8 66U Screw, Retaining 2 BLUE PANEL WITH PHILLIPS SCREW Use Standard Parts with Items Below: Grille and Venturi Assembly, Blue, Phillips Screw -- Includes Panel, Venturi Grille Assembly 9 66U Screw, Retaining 2 WHITE PANEL WITH PHILLIPS SCREW Use Standard Parts with Items Below: Grille and Venturi Assembly, White, Phillips Screw -- Includes Panel, Venturi Grille Assembly 9 66U Screw, Retaining 2 ORANGE PANEL WITH PHILLIPS SCREW Use Standard Parts with Items Below: Grille and Venturi Assembly, Orange, Phillips Screw -- Includes Panel, Venturi Grille Assembly 9 66U Screw, Retaining 2 9

27 2.2 COMPRESSOR TUBING

28 2.2 COMPRESSOR TUBING (Continued) Bracket, White Bracket, Orange 2 66U Screw, HXHD 0--2 X U Washer, Plain # Washer ID X OD Washer Fender # Tube Clamp U Screw Machine HXHD #0--2 X Tube Assembly Econo. with Fitting Protector 7.50 X U Screw, HXHD #0--2 X KA--66FA--060 Tube Clamp 2 66CH--72 Flexible Trim Tube Assembly Suction with Fitting 66U Screw, HXHD /--20 X U Washer, Plain / Washer ID X OD Bracket, White Bracket, Orange 8 66U Wire Tie /6--.0 Self--Linking Insulation, Tube Pre--Taped Insulation, Assembly Pre--Taped Seal Elbow Adapter Cap 2 66U Tube Clamp Seal / Tube Assembly Discharge with Fitting WireTie2.80Dia 7 REFRIGERATION TEMPERATURE SENSORS Sensor, Thermistor (CPDS) Sensor, Thermistor (CPSS) See Section

29 2. RECEIVER Receiver Assembly -- Includes: Glass, Sight Indicator, Moisture--Liquid Plug, Fusible, /8 NPT-- Brass Protector, Mylar U Screw, HXHD, /--20 X / Long -- SST 7 66U Washer, Flat, / -- SST Washer, Mylar SV Sensor, Ambient Thermistor (AMBS) 0 -- See Section 2.6 for Sensor Assembly and Related Parts Washer, Mylar, ID X 0.60 OD 2 66U Washer, Plain, #0 -- SST Unloader Solenoid Valve Coil, Unloader Solenoid Valve Bracket, White Bracket, Orange 22

30 2. WATER -COOLED CONDENSER 2,22,2,0,, ,6 5,6,7 8,9,20 2 7,8, Kit, Condenser/Receiver (For Field Installation) -- Includes: 69NT Condenser/Receiver -- Includes: Sight Glass, with Red Balls, /2 NPT Protector, Mylar Protector, Mylar 5 66U Coupling (Water--In) 6 66U2--2 Cap, Dust Coupling, Self Draining -- Includes: Seal, O--Ring 9 66U2--52 Cap, Dust SV Switch,Water Pressure OPTION W 66U Connector U--80 Heat Shrink Disc, Rupture, /8 NPT Indicator, Liquid Moisture -- Brass Tee, /2 X /2 X /8 NPT -- Brass 6 66U Screw, HXHD, #0--2 X / Long -- SST Nut, Self--Lock, # SST Washer, Mylar, ID X 0.60 OD 9 66U Washer, Plain, #0 -- SST Clamp, Cushion, /2 Diameter Unloader Solenoid Valve Coil, Unloader Solenoid Valve Bracket, White Bracket, Orange 2 -- See Section 2.6 for Sensor Assembly and Related Parts SV Sensor, Ambient Thermistor (AMBS) -- 2

31 2.5 ECONOMIZER, ECONOMIZER EXPANSION VALVE, ECONOMIZER SOLENOID VALVE AND FILTER DRIER

32 2.5 ECONOMIZER, ECONOMIZER EXPANSION VALVE, ECONOMIZER SOLENOID VALVE AND FILTER DRIER (Continued) 66U Screw Mach HXHD #0--2 X U Washer, Plain # Washer ID X Bracket, White Bracket, Orange Protector Valve Solenoid Valve -- Economizer Clamp, Tube Cushion 8 66U Screw Mach HXHD #0--2 X U Screw Cap HXHD /--20 X U Washer, Plain / Washer ID X Cover, White Cover, Orange Valve, Thermal Expansion -- Economizer Coil Solenoid Valve -- Economizer & Liquid injection U--80 Tube, Heat Shrink Coupling with Cap 7 66U Clamp,Tube Bracket 9 69NP20--0 Clamp, Tube Cushion 20 66U Gasket Neoprene SV Filter Drier -- Includes: Filter Drier, /2 Flare, O--Ring, Single -- Includes: O--Ring, Filter Drier PK25 Filter Drier, /2 Flare, O--Ring, 25 Pack -- Includes: A/R O--Ring, Filter Drier Solenoid Valve -- Liquid Injection Grommet 0.62 ID X 0.88 OD 26 DE0BA--0 Tee, Reducing 5/8 X 5/8 X / Clamp, Tube Cushion 0.8 Dia Bracket, White Bracket, Orange Bracket, White Bracket, Orange Heat Exchanger Assembly Bracket, White Bracket, Orange 2 DE0BA--20 Tee, Reducing /2 X /2 X / Clamp Cushioned Valve, Thermal Expansion -- Quench 25

33 2.6 SRS AND STS 2 2 (STS) (SRS) SV Sensor Assembly (STS & SRS) SV Cap, Probe -- Includes: Grommet NSS Cover, Probe 5 66U Washer, Flat, / -- SST U Screw, Machine, HXHD, #0--2 X 0.50 Long -- SST Holder, Probe 26

34 2.7 EVAPORATOR FAN ASSEMBLY EFM-- 2 (Location) EFM - (Location) 5 69NT--295 Mounting Bracket, Evaporator Fan Assembly 2 69NT Washer, Fender Washer, Lock, / -- SST Screw, HXHD, /--20 X --/ Long -- SST Nut, Self--Locking, 5/ SST Washer, Special, 5/8 -- SST Fan, Evaporator Stator, Evaporator Protector -- Mylar Motor, Evaporator Fan -- Includes: 2 NS Bearing, Front (Shaft End) NS Capacitor (20 μf) High Speed NS Pin #6 NS Plug Assembly, Motor (Located on Wire Harness) -- Includes: NS Plug NS Contacts A/R NS Receptacle Assembly, Motor -- Includes: NS Receptacle NS Strain Relief NS Contacts A/R 66U Washer, Flat, / -- SST Screw, HXHD, /--20 X --/8 Long -- SST Fan Deck, Right Fan Deck, Center Fan Deck, Left 27

35 2.8 UPPER FRESH AIR MAKE -UP AND ACCESS PANEL FRESH AIR PANEL WITH VPS BACK OF FRESH AIR PANEL OPTION - NONE (PLAIN EVAPORATOR ACCESS PANEL) SV Panel, Access -- Includes: A/R Gasket Gasket, X 0.50 Half Round Washer, Mylar, / ID X 0.80 OD Washer, Flat, / -- SST Screw, HXHD, /--20 X.00 Long -- TIR U Gasket, 0.75 X.5 X

36 2.8 UPPER FRESH AIR MAKE -UP AND ACCESS PANEL (Continued) OPTION 2 - FRESH AIR MAKEUP INSTALLED 7 66U Gasket, 0.75 X.5 X Panel, Fresh Air Make--up w/retaining Washers -- Includes: A/R Gasket Gasket, 0.26 X 0.50 Half Round 9 -- Label, Fresh Air (See Section 2.29 for Language Selection) Label, Fresh Air Washer, Mylar,.00 OD X 0.2 ID 22 66U Washer, Flat, 5/6 -- SST 2 66U Nut, Wing, 5/ SST OPTION - FRESH AIR MAKEUP AND SCREENS INSTALLED - USE ALL OF OPTION 2 AND ITEM BELOW Screen, Medfly 2 OPTION - FRESH AIR MAKEUP AND VENT POSITIONING SENSOR (VPS) INSTALLED 7 66U Gasket, 0.75 X.5 X Label, Fresh Air (See Section 2.29 for Language Selection) Label, Fresh Air Panel, Fresh Air Make--up with VPS, White -- Includes: A/R Panel, Fresh Air Make--up with VPS, Orange -- Includes: A/R Gasket Gasket, X 0.50 Half Round Washer, Mylar,.00 OD X 0.2 ID 22 66U Washer, Flat, 5/6 -- SST 2 66U Nut, Wing, 5/ SST HEATER ACCESS PANEL Washer, Flat, / -- SST Washer, Mylar, / ID X 0.80 OD Screw, HXHD, /--20 X.00 Long -- TIR SV Panel, Access -- Includes: Gasket Gasket, Access Panel STUD ASSEMBLY KITS (REPLACEMENT) Kit, Gasket and Stud Assembly (See NOTE ) -- Includes: Gasket (One Piece) Kit, Disc and Stud Assembly (See NOTE 2) -- Includes: 9 NSS Stud Assembly, 5/ Screw, Machine Pan Head, #8--2 X /2 Long -- SST Washer, Mylar,.00 OD X 0.2 ID 22 66U Washer, Flat, 5/6 -- SST 2 66U Nut, Wing, 5/ SST NOTES. Disc and stud assembly kit, which will modify stud to 5/6--8, also includes new disc and gasket. 2. Must order stud assembly kit, which will modify stud to 5/6--8, and include ( piece) gasket. 29

37 2.9 LOWER FRESH AIR MAKE -UP VENT OPTION ,2 2 9,0,2, ,6 20 7,2 2 9,0, OPTION -- 2 & 25 OPTION -- OPTION - NONE 69NT5--07 Panel, Blank 2 69NT--07 Bracket, Panel 66U Screw, HXHD, /--20 X / Long -- SST Washer, Mylar, / ID X.00 OD 5 66U Washer, Flat, /, Type A-- SST 6 69NT Washer, Fender / -- SST Gasket OPTION 2 - LOWER FRESH AIR INSTALLED 8 69NT Cover, Fresh Air Makeup -- Includes: 9 69NT Cover Assembly, Air Bleed -- Includes: Gasket, Air Exchange Nut, Hex, /--20 UNC--2B -- SST Nut, Hex, (with mini handle),/--20 UNC--2B -- SST Washer, Mylar, / ID X.00 OD 2 0

38 2.9 LOWER FRESH AIR MAKE -UP VENT (Continued) Gasket, Cover Gasket, Cover 5 69NT--782 Bushing U Washer, Flat, / -- SST Nut, Hex, /--20 UNC--2B -- SST A/R Nut, Hex, (with mini handle),/--20 UNC--2B -- SST A/R 8 69NT5--88 Baffle, Unpainted Rivet, Blind, 0.56 Diameter, Grip Range -- /6--/ 20 69NT Label, Fresh Air Label Kit -- Includes: Label, Air Exchange, CMH -- English 2 66CH Label, Arrow Label Kit -- Includes: 69NT5--7 Label, Air Exchange, CMH -- English (Maersk Specification) 2 66CH Label, Arrow (Maersk Specification) Label Kit -- Includes: 2 69NT Label, Air Exchange, CFM -- English/Spanish 2 66CH Label, Arrow Label Kit -- Includes: Label, Air Exchange, CMH -- English/Spanish/Chinese 2 66CH Label, Arrow Label Kit -- Includes: Label, Air Exchange, CMH -- English/Spanish/Chinese 2 (NYK Specification) Label, Arrow (NYK Specification) 69NT Label, Fresh Air Exchange, CMH -- English (Maersk Specification) 22 69NT Label, Fresh Air Exchange, CFM -- English/Spanish Label, Fresh Air Exchange, CMH -- English/Japanese/Chinese Label, Fresh Air Exchange, CMH -- English OPTION - LOWER FRESH AIR INSTALLED WITH SCREENS - USE ALL OF OPTION 2 AND ITEM BELOW Screen Assembly, Medfly 2 OPTION - LOWER FRESH AIR INSTALLED WITH VENT POSITION SENSOR Assembly, Vent Position Sensor -- Includes: Sensor Assembly -- Includes: Gear, 69NT, Auto LFA Screw, Set #8-- 2 X 0.56 Long Nut, Hex Jam / Washer, Lock / Bracket, 0.06 Thick SST Sensor, LVPS, Potentiometer 2 66U Screw, HXHD 0--2 X /2 gl. SST Nut, Hex, 0--2 UNC--2B -- SST 2 66U Washer, Flat, /2, Type A -- SST Washer, Mylar Label, LVPS, Air Exchange Assembly, Slide

39 2.20 EVAPORATOR COIL - REAR PANELS REMOVED (RTS and RRS) ,8,

40 2.20 EVAPORATOR COIL - REAR PANELS REMOVED (Continued) SV Sensor Assembly (RRS & RTS) 2 -- Sensor, Thermistor, (Temperature Recorder) SV Sensor, Thermistor, Defrost (DTS) Screw, HXHD, #8--2 X /2 Long -- SST 5 66U Thermostat, Heat Termination (HTT) 6 AUJR7 Washer, Lock, / -- SST NT Retainer (For Heaters) 8 69NT Clip (For Heaters) 9 69NT Washer, Flat, / -- SST U Screw, HXHD, #0--2 X.25 Long -- SST 2 66U Cap screw, HXHD, /--20 X / Long -- SST U Washer, Flat, / -- SST A/R Valve, Unloader Coil, Unloader Valve Heater, Evaporator Coil 5 -- USDA Option -- RefertoSection Plug, Hole (2 Inch diameter) (Located on Fan Deck) Sensor, Thermistor, (CPSS) Protector, Mylar 2 9 KA66FA8 Clamp,Tube/82Holes 20 66U Screw, Machine, HXHD, #0-2 X 0.50 Long - SST Valve, Stepper Motor -- Includes: Piston and Motor Assembly -- Includes: NS Connector (To Expansion Controller Module) NS Pin, Gauge (Used on ) NS Seal (Used on ) Coil, Evaporator (Does not include thermostats or heaters) Valve, Thermostatic Expansion, Hermetic DEHUMIDIFICATION Kit, Humidity Sensor(Field installation, units provisioned for - See Unit -- Matrix) -- Includes: Sensor, Humidity (HS) 26 66U Screw, HXHD, #0--2 X.00 Long -- SST 27 66U Washer, Flat, #0 -- SST Bracket Assembly, Humidity Sensor

41 2.2 USDA OPTION -- D OPTION -- V 0 2 OPTION OR 2

42 2.2 USDA (Continued) OPTION D Plug, Sealing Receptacle (PR, PR2, PR, Cargo Probe ) ( Pin) Receptacle, Interrogator (ICR) (5 Pin) NS 69NT--992 Plate Assembly, USDA -- Includes: 69NT--75 Cap, Dust, with Tether ( Pin) 5 69NT--76 Cap, Dust, with Chain (5 Pin) Contact, Pin, #6 (Used with & ) NS Plug, Interrogator Socket (ICR) (5 Pin) OPTION V Plug, Sealing Receptacle (PR, PR2, PR, Cargo Probe ) ( Pin) 69NT--75 Cap, Dust, with Tether ( Pin) Contact, Pin, #6 (Used with & ) Receptacle, Interrogator (5 Pin) Cap, Dust, with Tether (5 Pin) Socket, Contact (Silver Plated) A/R Socket, Contact (Gold Plated) A/R FIELD INSTALLED KITS (for units with USDA provision) Kit, USDA (For field installation, units provisioned for side -mounted -- USDA) -- Includes all of OPTION D. USDA PROBE KITS OPTION Sensor Assembly, 600 Long (5M) (USDA Probe) -- Includes: A/R Plug, Socket (PR, PR2, PR, Cargo Probe ) Contact, Socket, #6 (Used with & ) A/R OPTION Sensor Assembly, 50 Long (.5M) (USDA Probe) -- Includes: A/R Sensor Assembly, 600 Long (5M) (USDA Probe) -- Includes: A/R Plug, Socket (PR, PR2, PR, Cargo Probe ) Contact, Socket, #6 (Used with & ) A/R NOTE Do not mix silver pins with gold pins and sockets. 5

43 2.22 BACK PANEL ASSEMBLY - OPTION - ALUMINUM BOLTED

44 2.22 BACK PANEL ASSEMBLY - OPTION - ALUMINUM BOLTED (Continued) 69NT--6 Grille, Top (Unpainted) Rivet, Blind, 5/2 Diameter, Grip Range -- /8--/ 2 66U Rivet, TIR, /6 Diameter, Grip Range -- 5/6--/ Panel Assembly, Upper -- Includes: NS Panel NS Drain Pan, Side (Location -- Behind upper panel) NS Drain Pan, Center (Location -- Behind upper panel -- Top) NS Drain NS Plate NS NSS Drain Pan (Location -- Behind upper panel) 2 NS Gasket (Location -- Behind upper panel) NS 66U Gasket (25 Feet, cut to length) A/R Rivet, Blind, /8 Diameter, Grip Range -- /8--/ Rivet, Blind, /8 Diameter, Grip Range -- /6--/ Panel, Bottom, (Painted) Panel, Bottom, (Unpainted) Panel, Bottom (Provision for Heat Exchanger location), (Painted) Panel, Bottom (Provision for Heat Exchanger location), (Unpainted) 9 66U--20 Screw, Machine, Truss Head, #0--2 X /2 Long -- SST NT Washer, Fender, #0 X.00 OD -- SST 20 69NT Duct, Air Label, Carrier Transicold 7

45 2.2 OPTION 7 AND OPTION 8 - ELECTRONIC PARTLOW TEMPERATURE RECORDER OPTION -- 7 and OPTION 9 - NO TEMPERATURE RECORDER OPTION

46 2.2 OPTION 7 AND OPTION 8 - ELECTRONIC PARTLOW TEMPERATURE RECORDER (Continued) OPTION 7 Partlow Recorder Kit, Standard -- Includes: Recorder, Box & Door Assemblies (For field installation, units provisioned for - Refer to online Matrix ) Electronic Temperature Recorder Partlow Recorder Kit, Special -- Includes: Recorder, Box & Door Assemblies OPTION 8 (For field installation, units provisioned for - Refer to online Matrix ) Electronic Temperature Recorder Door Assembly -- Includes: Seal, Door -- Rubber Screw, HXHD, SEMS, #0--2 X 5/6 Long Protector -- Mylar Hinge Screw, HXHD, #0--2 X 7/6 Long -- SST 8 69NT Window 9 69NT Gasket Nut, Self--Locking, / U Screw, Retaining Panel Thickness -- SST Washer, 0.25 ID X.00 OD -- Mylar Washer, Retaining -- SST SV Box Assembly -- Includes: Grommet, /8 ID X.25 OD Plug, Hole, 0.50 DIA Washer, / ID X OD -- Mylar Screw, HXHD, SEMS, #0--2 X 7/6 Long 9 66U Washer, Flat, / -- SST U Screw, Cap, HXHD, /--20 X 0.75 Long -- SST Washer, Retaining, 0.9 ID X 0.80 OD -- Mylar NT Washer, Fender, / ID X OD Washer, 0.25 ID X 0.9 OD -- Mylar Stylus, Electronic Partlow Kit, Includes: NS -- Chart -- Owner Supplied A/R NS Charts _F -- Day (Box of 50) (--20_F to +80_F) A/R NS Charts _C -- Day (Box of 50) (--25_C to +25_C) A/R OPTION 9 - NO TEMPERATURE RECORDER Panel, White Panel, Orange 26 66U Washer, Flat, / -- SST U Screw, Cap HXHD, /--20 X 0.75 Long -- SST Washer, Retaining, 0.95 ID X 0.80 OD -- Mylar NT Washer, Fender, / ID X OD Washer, 0.25 ID X.00 OD -- Mylar 2 9

47 2.2 COMPRESSOR MOUNTING COMPONENTS AND GUARD

48 2.2 COMPRESSOR MOUNTING COMPONENTS AND GUARD (Continued) Compressor, Scroll -- Includes: (See Section ) Seal, Rotolock, -- NS Seal, Rotolock, --/--2 2 NS Compressor Oil O--Ring Shockmount, Bushing Shockmount, Ring Mount, Resilient, 80A Washer, Mylar X Washer, X.50 X SST Protector, Mylar SV Base, Compressor (Painted) -- Includes: Protector, Mylar Bolt, Shoulder, /2-- UNC -- SST Bracket Assembly Bracket Assembly 5 66U Bolt, Machine HXHD, /--20 X.25 Long -- SST 6 66U Washer, Plain / -- SST Protector, Mylar Washer, Mylar ID X OD Nut, Self Lock / SST Nut, Self Lock / SST 2 66U Washer, Plain /8 N Type A -- SST Washer, Mylar 0.75 ID X.00 OD Washer, Snubbing 0.57 ID X 2.00 OD Bolt, Shoulder, /8--6 UNC -- SST Screw, Cap HXHD /--20 X SST Cable, Power NS Cover, Compressor

49 2 2.2 COMPRESSOR MOUNTING COMPONENTS AND GUARDS (Continued) ITEM REMOVED FOR CLARITY ITEM REMOVED FOR CLARITY

50 2.2 COMPRESSOR MOUNTING COMPONENTS AND GUARDS (Continued) STANDARD PARTS INCLUDED IN ALL KITS xx Standard Parts Included in the Service Kits Include: Nut, Lock, / NPT 28 66U O--Ring, / Hub Sealing 29 66U Screw, Cap, HXHD /--20 x Washer, ID x OD 9 66U Washer, Plain / W Type A 2 66U Screw, Cap, HXHD /--20 x Nut, Self Lock / NT Washer, Fender / OD Washer, ID x.000 OD 6 66U Screw, Mach, HXHD #0--2 x Slotted U Washer, Plain #0 Type A Washer ID x OD 2 9 PF Sealer, Mastic, Linear. Feet 0 PF Sealer, Clear, Silicone, gal Protector,.6 x.00 Long Base, Mounting, Diameter Mtg Hole 66U--882 Wire Tie, /6----/ Self Lock OPTION - STANDARD CABLE WITH RECEIVER OPTION SEE ABOVE FOR STANDARD PARTS INCLUDED IN THE KIT AND USE WITH ITEMS BELOW: Standard Cable with Receiver Option Includes: Cable Clamp, Cable Cutter 6 Gage 5 66U--752 Connector, Straight, Watertight Cover, 0.06 Thick Aluminum Guard, Thick Alum Guard, 0.25 Thick Alum Brace, Support 0.06 Thick Alum OPTION 2 - STANDARD CABLE WITH FULL GUARD SEE ABOVE FOR STANDARD PARTS INCLUDED IN THE KIT AND USE WITH ITEMS BELOW: Standard Cable with Full Guard Includes: 66U--752 Connector, Straight, Watertight Cable Clamp, Cable Cutter 6 Gage Cover, 0.06 Thick Alum Guard, 0.25 Thick Alum Partition, 0.90 Thick Alum Bracket 0.25 Thick Alum 2 OPTION - TRANSICORD WITH FULL GUARD SEE ABOVE FOR STANDARD PARTS INCLUDED IN THE KIT AND USE WITH ITEMS BELOW: Transicord with Full Guard Includes: 66U--752 Connector, Straight, Watertight Cable Clamp, Cable Cutter 6 Gage Cover, 0.06 Thick Alum Guard, 0.25 Thick Brace, Support 0.06 Thick Alum