Container Refrigeration. SERVICE PARTS LIST for 69NT , 314 & 328 Upflow Container Refrigeration Units T--354PL

Transcription

1 R Container Refrigeration SERVICE PARTS LIST for 69NT , 3 & 38 Upflow Container Refrigeration Units T--3PL

2 SERVICE PARTS LIST UPFLOW CONTAINER REFRIGERATION UNITS Models 69NT , 3 & 38

3 TABLE OF CONTENTS PARAGRAPH NUMBER Page INTRODUCTION... iii CONFIGURATION IDENTIFICATION... iii OPTION DESCRIPTIONS... iii QUICK LIST -- CLAMPS, FILTER--DRIER, FUSE, TY--RAPS, WIRE TERMINALS & REPLACEMENT UNIT FRAMES... REFRIGERATION UNIT ASSEMBLY.... REFRIGERATION UNIT -- AREA LOCATOR.... RAIN GUTTERS....3 HANDLES.... THERMOMETER PORT.... CONTROL BOX DOOR -- LCD AND LED DISPLAYS CONTROL BOX CONTROL BOX PREPARATION CONTROL BOX -- SHIELDS REMOVED, STD ELECTRICAL COMPONENTS, RM, HOURMETER & CFS....9 CONTROL BOX -- SINGLE EVAPORATOR FAN CAPABILITY, EBS, ED CONTROL BOX -- CONTROLLER MODULE SECTION AND SOFTWARE CARDS CONTROL BOX -- DISPLAY MODULE & COMMUNICATIONS INTERFACE MODULE CONDENSER FAN MOTOR AND CONDENSER COIL SECTION....3 COMPRESSOR TUBING SECTION.... RECEIVER SECTION WATER--COOLED CONDENSER SECTION RRS AND RTS SECTION THERMOSTATIC EXPANSION VALVE UPPER FRESH AIR MAKE--UP AND ACCESS PANEL SECTION LOWER FRESH AIR MAKE--UP VENT EVAPORATOR FAN ASSEMBLY EVAPORATOR COIL SECTION -- REAR PANELS REMOVED EVAPORATOR FAN DECK USDA SECTION.... BACK PANEL ASSEMBLY -- OPTION -- ALUMINUM BOLTED.... BACK PANEL ASSEMBLY -- OPTION 3 -- ALUMINUM BOLTED / PROBE ACCESS DOOR 6.6 BACK PANEL ASSEMBLY -- OPTION 8 -- HINGED ALUMINUM / DRAIN ACCESS DOOR. 8.7 BACK PANEL ASSEMBLY -- OPTION -- ALUMINUM HINGED BACK PANEL ASSEMBLY -- OPTION -- STAINLESS STEEL HINGED....9 ELECTRONIC PARTLOW TEMPERATURE RECORDER -- OPTION 7 AND OPTION NO TEMPERATURE RECORDER -- OPTION COMPRESSOR MOUNTING, GUARD, CRANKCASE HEATER COMPONENTS COMPRESSOR GAUGES AND TRANSDUCERS CABLE RESTRAINT COMPONENTS VOLTAGE CABLES AUTOTRANSFORMER KIT LABELS AND DECALS (Not Applicable to All Units) i T-3PL

4 TABLE OF CONTENTS (Continued) PARAGRAPH NUMBER Page 3 INTERROGATOR AND ACCESSORIES DATAVIEW/DATAREADER INTERROGATOR RECEPTACLE COMPRESSOR ASSEMBLY OPTION R -- SERVICE REPLACEMENT COMPRESSOR TERMINAL MOUNTING AND JUNCTION BOX GROUP SERVICE VALVE GROUP COMPRESSOR -- MOTOR BODY GROUP PUMP END GROUP CRANKSHAFT, ROD AND PISTON GROUP VALVE PLATE GROUP GASKET SET... 7 CONTROLLER/DATACORDER CONFIGURATION TOOLS T-3PL ii

5 INTRODUCTION INTRODUCTION The Carrier Transicold model 69NT0--300/399 series units are of lightweight aluminum frame construction, designed to fit in the front of a container and serve as the container front wall. CONFIGURATION IDENTIFICATION Unit identification information is provided on a plate located near the compressor. The plate provides the unit model number, the unit serial number and the unit parts identification number (PID). The model number identifies the overall unit configuration while the PID provides information on specific optional equipment, factory provision to allow for field installation of optional equipment and differences in detailed parts. Configuration identification for the models covered herein may be obtained on the Container Products Group Information Center by authorized Carrier Transicold Service Centers. 3 OPTION DESCRIPTIONS Various options may be factory or field fitted to the base unit. These options are listed in the tables and described in the following subparagraphs. 3. Battery The refrigeration controller may be fitted with a rechargeable battery pack. 3. Dehumidification The unit may be fitted with a humidity sensor. This sensor allows setting of a humidity set point in the controller. In the dehumidification mode the controller will operate to reduce internal container moisture level. 3.3 Control Box The control box is made of a composite material and may be fitted with a lockable door. 3. Display Module The unit may be fitted with a backlit Liquid Crystal Display (LCD) or a Light Emitting Diode (LED) Display. 3. Temperature Readout The unit may be fitted with suction and discharge temperature sensors. The sensor readings may be viewed on the controller display. 3.6 Pressure Readout The unit may be fitted with suction and discharge pressure gauges or suction and discharge transducers or no pressure readout. The transducer readings may be viewed on the controller display. 3.7 USDA The unit may be supplied with fittings for additional temperature probes which allow recording of USDA Cold Treatment data by the integral DataCORDER function of the Micro-Link refrigeration controller. 3.8 Interrogator Units that use the DataCORDER function are fitted with interrogator receptacles for connection of equipment to download the recorded data. Two receptacles may be fitted, one accessible from the front of the container and the other mounted inside the container (with the USDA receptacles). 3.9 Remote Monitoring The unit may be fitted with a remote monitoring receptacle. This item allows connection of remote indicators for COOL, DEFROST and IN RANGE. Unless otherwise indicated, the receptacle is mounted at the control box location 3.0 Communications The unit may be fitted with a communications interface module. The communications interface module is a slave module which allows communication with a master central monitoring station. The module will respond to communication and return information over the main power line. Refer to the ship master system technical manual for further information. 3. Compressor The unit is fitted with a single speed reciprocating compressor. 3. Condenser Coil Theunitisfittedwitha3rowcoilusing7mmtubing. 3.3 Autotransformer An autotransformer may be provided to allow operation on 90/30, 3phase, 0/60 hertz power. The autotransformer raises the supply voltage to the nominal 380/60 volt power required by the base unit. The autotransformer may also be fitted with an individual circuit breaker for the 30 volt power. If the unit is fitted with an autotransformer and communications module, the autotransformer will be fitted with a transformer bridge unit (TBU) to assist in communications. 3. Temperature Recorder Units may be fitted with an electronic recorder. 3. Gutters Rain gutters may be fitted over the control box and recorder section to divert rain away form the controls. The different gutters include standard length bolted gutters, extended length gutters and riveted gutters. 3.6 Handles The unit may be fitted with handles to facilitate access to stacked containers. These handles may included fixed handles (located at the sides of the unit) and/or a hinged handle at the center (attached to the condenser coil cover). 3.7 Thermometer Port The unit may be fitted with ports in the front of the frame for insertion of a thermometer to measure supply and/or return air temperature. If fitted, the port(s) will require a cap and chain. iii T-38PL

6 3.8 Water Cooling The refrigeration system may be fitted with a water cooled condenser. The condenser is constructed using copper-nickel tube for sea water applications. The water cooled condenser is in series with the air cooled condenser replaces the standard unit receiver. When operating on the water cooled condenser, the condenser fan is deactivated by either a water pressure switch or condenser fan switch. Depending on the unit s configuration and the compressor discharge temperature the condenser fan may also be activated during water cooled condenser operation. 3.9 Back Panels Back panel designs that may be fitted include panels of aluminum and stainless steel. Panels may be fitted with access doors and/or hinge mounting Volt Cable Various power cable and plug designs are available for the main 60 volt supply. The plug options tailor the cables to each customers requirements Volt Cable Units equipped with an autotransformer require an additional power cable for connection to the 30 volt source. Various power cable and plug designs are available. The plug options tailor the cables to each customers requirements. 3. Cable Restraint Various designs are available for storage of the power cables. These options are variations of the compressor section front cover. 3.3 Upper Air (Fresh Air Make Up) The unit may be fitted with an upper fresh air makeup assembly. The fresh air makeup assembly is available with a Vent Positioning Sensor (VPS) and may also be fitted with USDA screens. 3. Lower Air (Fresh Air Make Up) The unit may be fitted with a lower fresh air makeup assembly. These assemblies are available with a Vent Positioning Sensor (VPS) and may also be fitted with USDA screens. 3. Controlled Atmosphere Controlled atmosphere units may be fitted with the TransFresh or the complete Carrier Transicold EverFresh option. For information on the TransFresh system, contact TransFresh Corporation, P.O. Box 788, Salinas CA 9390 The EverFresh option is the addition of the Carrier Transicold EverFresh controlled atmosphere system. This system continuously monitors and controls oxygen and carbon dioxide levels in the container. 3.6 Arctic Mode To improve operation in cold ambients, the unit may be fitted with a crankcase heater. The crankcase heater is operated any time the unit is under power and the compressor is not running. The purpose of the heater is to warm the compressor oil and boil off any liquid refrigerant that may be present in the crankcase. 3.7 Power Correction The unit may be fitted with a set of power factor correction capacitors to assist in correction of imbalance in current draw by the compressor. 3.8 Evaporator Evaporator section options include a hermetic thermal expansion valve and two sizes of heat exchangers. 3.9 Evaporator Fan Operation Two evaporator fan motor operation systems are available. On units with Normal Evaporator Fan Operation, opening of an evaporator fan internal protector will shut down the unit. On units equipped with Single Evaporator Fan Capability, additional contactors are installed to allow the unit to continue to operate on a single fan Labels Operating Instruction and Function Code listing labels will differ depending on the options installed. For example, additional operating instructions are required to describe start-up of a unit equipped with an autotransformer. Where the labels are available with additional languages, they are listed in the parts list. 3.3 Plate Set Each unit is equipped with a tethered set of wiring schematic and wiring diagram plates. The plate sets are ordered using a seven digit base part number and a two digit dash number. 3.3 Controller Two different controllers are available:. Remanufactured - Controller is the equivalent of a new OEM controller and is supplied with a month warranty.. Repaired - Controller has had previous faults repaired and upgraded with the latest software. Note: Repaired controllers are NOT to be used for warranty repairs only full OEM Remanufactured controllers are to be used. Controllers will be factory equipped with the latest version of operational software, but will NOT be configured for a specific model number and will need to be configured, at the time of installation or sale Condenser Grille Two styles of condenser grilles are available, direct bolted grilles and hinged grilles. 3.3 Emergency Bypass The unit may be equipped with switches to allow emergency bypass of the controller. The EMERGENCY BYPASS switch functions to bypass the controller in the event of controller failure. The EMERGENCY DEFROST switch functions to bypass the all controls and place the unit in the defrost mode. T-38PL iv

7 OPTION LEGEND General - Feature Not Applicable X P Battery Codes R Features that apply to model Factory Installation of Equipment to Allow Field Installation Control Box Codes C CL Display Module Codes Rechargeable Cells Composite Box Without Door Lock Composite Box With Door Lock LCD Display LED Display Pressure Readout Codes G T SG Factory Installed Pressure Gauges Factory Installed Pressure Transducers Factory Installed Suction Pressure Gauge USDA/Cable Codes D/- V/- Option D Only Option V Only D/ Option V/Option V/ Option V/Option D/ Option V/Option V/ Option V/Option Interrogator Codes Left Straight Mount Right Straight Mount 3 Box Mount Left Mount Left Angled Mount 6 Right Mount Communications Codes HighDataRate Low Data Rate Compressor Codes R Condenser/Receiver Codes Single Speed Reciprocating 3 Three Row (7mm) Coil AutoTransformer Codes Transformer Fitted Transformer With CB Fitted 3 Transformer With CB and Receptacle Transformer With CB and Transformer Bridging Unit Temperature Recorder Codes 7 Standard Electronic Partlow 8 Special Electronic Partlow 9 No Temperature Recorder 0 Electronic Partlow (Both) Gutter Codes Standard Length Bolted Gutters 3 Extended Length Gutters Riveted Gutters Handle Codes Two Side and One Center Two Side 3 One Center One Right Side and Two Center Thermometer Port Codes Supply Air Port Return Air Port B Water Cooling Codes W F Back Panel Codes Both Ports Water Pressure Switch Condenser Fan Switch Bolted Panels Bolted Panels With USDA Door Hinged Panels Hinged Stainless Steel Panels 60 Volt Cable Codes Option Option 3 Option 3 Option Option 6 Option 6 7 Option 7 8 Option 8 9 Option 9 0 Option 0 v T-38PL

8 30 Volt Cable Codes Option Option 3 Option 3 Option Option 6 Option 6 7 Option 7 8 Option 8 9 Option 9 Cable Restraint Codes Cable Door Left Bungy Cord Only 3 J-Hook Left and Right Bungy Cord Left Bungy Cord With Left Extended Guard 6 Left & Right Bungy Cords With Extended Guards Upper Air Codes No Upper Fresh Air Upper Fresh Air Installed 3 Upper Fresh Air Installed With USDA Screen Upper Fresh Air Installed with Vent Position Sensor (VPS) Lower Air Codes No Lower Fresh Air Lower Fresh Air Installed 3 Lower Fresh Air With USDA Screen Installed Lower Fresh Air Installed with Vent Position Sensor (VPS) Controlled Atmosphere TransFresh Carrier Transicold Everfresh System Arctic Mode Codes C Condenser Grille Codes B H Evaporator Codes Crankcase Heater Bolted Grille Hinged Grille Coil With Hermetic TXV & Standard Heat Exchanger (6 Heaters) 6 Coil With Hermetic TXV & Large Heat Exchanger (6 Heaters) Evaporator Fan Codes Normal Evaporator Fan Operation Single Evaporator Fan Operation Capability Label Codes English English / Spanish 3 English / French English / Korean English / Traditional Chinese 6 English / Simplified Chinese 7 English / Japanese / Chinese 8 English/German Emergency Bypass Codes B EB Emergency Bypass & Emergency Defrost Emergency Bypass Only Ordering Instructions All orders and inquiries for parts must include: Parts Identification Number (PID), Model Number, Unit Serial Number, Part Number, Description of part as shown on list and Quantity required. Address all correspondence for parts to the following address: CARRIER TRANSICOLD DIVISION Replacement Components Group, TR-0 P.O. Box 80, Syracuse, New York 3 or FAX to: (3) Letter Designations The following letter designations are used to classify parts throughout this list: A/R N/A = = As Required Not Available NS NSS = = Not shown in illustration Not sold separately - Order next higher assembly or kit PID PL = = Parts Identification Number - essential to identify unit configuration. Purchase Locally SST SV = = Stainless Steel Series unless otherwise specified. Suffix SV - added to part number designates service replacement part. T-38PL vi

9 QUICK LIST - CLAMPS, FILTER -DRIER, FUSE, TY -RAPS, WIRE TERMINALS AND REPLACEMENT UNIT FRAMES PART NO. DESCRIPTION Clamp, Tube, / -- SST Clamp, Tube, 3/8 -- SST Clamp, Tube, / -- SST Clamp, Tube, /8 -- SST Clamp, Tube, 3/ -- SST Clamp, Tube, 7/8 -- SST Clamp, Tube, --/8 -- SST Clamp, Tube, --/ -- SST Clamp, Tube, --3/8 -- SST Clamp, Tube, --/ -- SST Connector, Butt End, Wire Range -- to 6 AWG Connector, Butt End, Wire Range -- 6 to AWG Connector, Butt End, Wire Range -- to 0 AWG Connector, Closed End, Wire Range -- to AWG Connector, Closed End, Wire Range -- 8 to 0 AWG SV Filter--Drier Fuse, Amp (F, F, & FED) Fuse, 0 Amp (FEB) Fuse, 7. Amp (F3A & F3B) Ring Terminal, #6, Wire Range -- to 0 AWG Ring Terminal, #0, Wire Range -- to 0 AWG Ring Terminal, 3/8, Wire Range -- to 0 AWG Ring Terminal, /, Wire Range -- to 0 AWG Ring Terminal, #0, Wire Range -- 6 to AWG Ring Terminal, /6, Wire Range -- 6 to AWG Ring Terminal, #0, Wire Range -- to 6 AWG Ring Terminal, 3/8, Wire Range -- 6 to AWG Spade Terminal, / x /6, Wire Range -- 6 to AWG Spade Terminal, 3/8, Wire Range -- to 0 AWG Spiral Wrap, / Diameter x ft. lg Spiral Wrap, / Diameter x ft. lg. 66U Tube, Heat Shrink, / ID x --/8 lg. 66U Tube, Heat Shrink, / ID x --3/ lg Ty--Raps, --/ inches lg Ty--Raps,.00 inches lg Series Wire Markers Sealant, Pipe (Used to seal fittings on unit with R--3a) Cleaner, Coil Paint, Compressor Touch--Up, Blue 69NT NT Unit Frame, Service Replacement Contact Carrier Replacement Components Group for application T-3PL

10 REFRIGERATION UNIT ASSEMBLY. REFRIGERATION UNIT - AREA LOCATOR T-3PL

11 . REFRIGERATION UNIT - AREA LOCATOR Item Section Number Area Description Refer to Section.8 Upper Fresh Air Makeup & Access Panels Refer to Section. Thermometer Port 3 Refer to Section.36 Labels and Decals Refer to Section.0 Evaporator Fan Assembly Refer to Section. Evaporator Coil 6 Refer to Section. Evaporator Fan Deck 7 Refer to Section. Motor, Condenser Fan 8 Refer to Section. Rain Gutters 9 Refer to Section. --. Box, Control 0 Refer to Section.3 Handles Refer to Section. Coil, Condenser and Fan, Condenser Refer to Section. or. Receiver or Water--Cooled Condenser 3 Refer to Sections.3 or Compressor Refer to Sections.3 Compressor Tubing Refer to Sections.3 Compressor Gauges and Transducers 6 Refer to Section.3 Guard, Compressor 7 Refer to Section.3 Cable, Power 8 Refer to Section.3 Plug, Power 9 Refer to Section.33 Cable Restraint 0 Refer to Section.3 Autotransformer Refer to Section 3 Interrogator and Accessories Refer to Section.9,.30 Temperature Recorder 3 Refer to Section.9 Lower Fresh Air Makeup Refer to Section.6 RRS and RTS Refer to Section.7 Thermostatic Expansion Valve 6 Refer to Section.3 USDA 7 Refer to Section.--.8 Back Panels 3 T-3PL

12 . RAIN GUTTERS or or 3 or OPTION - STANDARD LENGTH - BOLTED 69NT Gutter, Rain (Bolted, Standard - Right Side) 69NT Gutter, Rain (Bolted, Standard & Extended Length - Left Side) OPTION 3 - EXTENDED LENGTH - BOLTED 69NT Gutter, Rain (Bolted, Standard & Extended Length - Left Side) 3 69NT3--88 Gutter, Rain (Bolted - Right Side) OPTION - RIVETED Gutter, Rain (Riveted - Right and Left Side).3 HANDLES OPTION - TWO SIDE, ONE CENTER 69NT3--83 Handle, Fixed 69NT Handle, Hinged OPTION - TWO SIDE 69NT3--83 Handle, Fixed OPTION 3 - ONE CENTER 69NT Handle, Hinged OPTION - ONE RIGHT SIDE AND TWO CENTER 69NT3--83 Handle, Fixed 69NT Handle, Hinged T-3PL

13 . THERMOMETER PORT 3 OPTION - SUPPLY AIR PORT 66U--866 Cap & Chain Assembly Label OPTION - RETURN AIR PORT 3 66U--866 Cap & Chain Assembly Label OPTION B - SUPPLY AND RETURN PORTS & 3 66U--866 Cap & Chain Assembly & Label T-3PL

14 . CONTROL BOX DOOR - LCD AND LED DISPLAYS Control Box Control Box Door HINGE ASSEMBLY - SECTIONAL VIEW DOOR ASSEMBLY - PARTIAL BACK VIEW T-3PL 6

15 . CONTROL BOX DOOR - LCD AND LED DISPLAYS (Continued) OPTION, LCD DISPLAY Door Assembly, LCD Display, Includes: Gasket, Door SV Window and Gasket Assembly, Control Box Door -- Lexan Washer, Retaining -- SST 66U Screw, Retaining, Panel, SST 66U Screw, Retaining, Wing, SST Washer, Mylar, 0.0 ID x OD Hinge, Half 8 66U Screw, Truss Head, #0-- x 3/ lg. -- SST 9 66U Washer, Lock, #0 -- SST U Washer, Flat, #0 -- SST Washer, Mylar, 0.0 ID x OD Hinge, Half Protector, Mylar (Hinge) (Not Needed with Composite Box) Retainer, Nut Protector, Mylar (Hinge) Pocket, Placard Locknut, Hex Head, # SST Rivet, Blind, /8 Diameter, Grip Range Pin Assembly, with Tether 0 66U Screw, #0-- x / lg. -- SST 66U Washer, Flat, #0 -- SST Door Strap Kit OPTION, LED DISPLAY Door Assembly, LED Display, Includes: Gasket, Door 3 69NT Window Foam, Double Coated Washer, Retaining -- SST 66U Screw, Retaining, Panel, SST 66U Screw, Retaining, Wing, SST Hinge, Half 8 66U Screw, Truss Head, #0-- x 3/ lg. -- SST Washer, Lock, #0 -- SST 0 66U Washer, Flat, #0 -- SST Washer, Mylar, 0.0 ID x OD Hinge, Half Retainer, Nut Pocket, Placard Locknut, Hex Head, # SST Rivet, Blind, /8 Diameter, Grip Range Pin Assembly, with Tether 66U Washer, Flat, #0 -- SST 7 T-3PL

16 .6 CONTROL BOX MANUAL DEFROST/ INTERVAL T-3PL 8

17 .6 CONTROL BOX (Continued) -- Plate, Schematic & Diagram (Container Unit Matrix) 66U--03 Screw, Truss Head, #0-- x / lg. -- SST 3 69NT3---- Shield, High Voltage (Plastic) -- Includes: Hinge Rivet, Blind, /8 Diameter, Grip Range -- /8--3/6 -- SST Stud & Retainer Package -- Includes: NS NSS Stud, Fastener NS NSS Retainer, Fastener Stud Receptacle 8 69NT3 - -SV Shield, Low Voltage (Lexan) -- With Tether Label, Danger--High Voltage 9 T-3PL

18 .7 CONTROL BOX PREPARATION OPTION ONLY 3 GROUND WIRE OPTION 3 ONLY LATCHED DOOR - OPTION STANDARD SCREW FASTENED DOOR AND LOCKING DOOR WITH LOWER BOLT SEAL OPTION LOCKING DOOR - OPTION 3 T-3PL 0

19 .7 CONTROL BOX PREPARATION (Continued) STANDARD PARTS INCLUDED IN OPTIONS 66U Plug Button,. Inch Diameter Hole Plug Button, Inch Diameter Hole Bracket, Thick Aluminum 66U Screw, Machine Hex Head #0-- X U Washer, Plain, #0 Type A Label, Warning! ML3 Controller Only! 7 66U Gasket, V Type, 6.38 Inches Long Spacer, Locking (Subpanel) 9 66U Washer, Plain, / W, Type A Screw, Captive, Hex Head, /--0 X Washer, 0.0 ID X.000 OD 69NT Strap Assembly Ground, All Populated 3 66U Standoff, /--0 X 0.37 Inches Long Nut, Self--Locking, /--0 66U Washer, Plain, / N, Type A 6 AU7JR7 Washer, Lock, / Ext Tooth 0 7 AT39JA7 Nut, Hex, /--0 0 OPTION - LATCH FASTENER, BLUE BOX Control Box, Blue Bracket, Latch Closure, Blue Stop, Door Latch, Latch Closure, Blue Keeper, Latch Closure Protector, 0.88 X.93, Two Holes Rivet, Blind, 0. Inch Diameter, OPTION - SCREW FASTENERS, BLUE BOX Control Box, Blue 69NT3--67 Bracket, 0.063, Thick Aluminum, Blue Washer, 0.0 ID X OD Receptacle, #, Saddle Type Rivet, Blind, 0. Inch Diameter, Protector, 0.7 X.06 Inches, Mylar T-3PL

20 .7 CONTROL BOX PREPARATION (Continued) OPTION - SCREW FASTENERS, ORANGE BOX Control Box, Orange 69NT Bracket, Thick Aluminum, Orange Washer, 0.0 ID X OD Receptacle, #, Saddle Type Rivet, Blind, 0. Inch Diameter, Protector, 0.7 X.06, Mylar OPTION - SCREW FASTENERS, WHITE BOX Control Box, White 69NT Bracket, Thick Aluminum, White Washer, 0.0 ID X OD Receptacle, #, Saddle Type Rivet, Blind, 0. Inch Diameter, Protector, 0.7 X.06, Mylar OPTION - SCREW FASTENER, LOCKING DOOR WITH LOWER BOLT SEAL, BLUE BOX Control Box, Blue 69NT3--67 Bracket, Thick Aluminum Washer, 0.0 ID X OD Receptacle, #, Saddle Type Rivet, Blind, 0. Inch Diameter, Protector, 0.7 X.06, Mylar Bracket, Lock Tab Protector, 0. X 0.7, Mylar Washer, Plain #0, Type A Washer, Lock #0 Spring T-3PL

21 .7 CONTROL BOX PREPARATION (Continued) OPTION 3 - SCREW FASTENER, LOCKING DOOR, BLUE BOX Control Box, Blue 69NT Bracket, Gage, SST Washer, 0.0 ID X 0.9 OD Receptacle, #, Saddle Type Rivet, Blind, 0. Inch Diameter, Protector, 0.7 X.06, Mylar OPTION 3 - SCREW FASTENER, LOCKING DOOR, BOLT SEAL, BLUE BOX Control Box, Blue 69NT Bracket, Gage, SST Washer, 0.0 ID X 0.9 OD Receptacle, #, Saddle Type Rivet, Blind, 0. Inch Diameter, Protector, 0.7 X.06, Mylar 3 T-3PL

22 .8 CONTROL BOX - SHIELDS REMOVED, STD ELECTRICAL COMPONENTS, RM, HOURMETER & CFS See.3 OPTION C MANUAL DEFROST/ INTERVAL or REMOTE MONITORING --- LOWER/EXTERNAL MTG Contactor, Compressor (CH) (30 Amp) Screw, Pan Head, (Thread Cutting) #8--3 x 3/ lg. -- SST Contactors, (CF), (HR) & (EF & ES) ( Amp) Panel, Contactor Screw, Hex Head, /--0 x /8 lg. -- SST Rivet, Blind, /8 Diameter, Grip Range -- /6 -- / Receptacle SV Switch, Toggle (On -Off) 9 66U--97 Seal, Bushing Switch, Toggle (MDS) (if equipped) 39 0 T-3PL

23 .8 CONTROL BOX - SHIELDS REMOVED, STANDARD ELECTRICAL COMPONENTS (Continued) Plate, Switch A/R Plate, Switch (Start Only) NT--00 and Up A/R Plate, Switch (Start and Defrost LED), NT--00 and Up A/R Plate, Switch (Start and MDS), NT--00 and Up A/R 69NT Plate, Ground SV Transformer, Base Unit 66U Screw, Hex Head, #0-- x / lg. -- SST A/R 66U Washer, Flat, #0 -- SST A/R Contact, Auxiliary Washer, Lock, #6 -- SST 8 66U Circuit Breaker vac, Amp, (CB) 9 66U Screw, Pan Head, #6--3 x 3/8 lg. -- SST 0 69NT Bracket, Circuit Breaker Transformer, Current Sensing (CS) 66U Screw, Hex Head, #0-- x.00 lg. -- SST 3 66U Washer, Flat, #0 -- SST 66CH Trim, Flexible (8 Feet Long, Cut to Length) A/R SV Pad, Key -- Includes: 6 NSS Gasket (Between Key Pad Plate Assembly and Connector) 7 NSS Gasket (Between Key Pad and Key Pad Plate Assembly 8 NSS Plate Assembly, Key Pad Mounting Screw, Pan Head, #0-- X 3/ lg. -- SST Washer, Mylar, 0.0 ID x OD 6 REMOTE MONITORING (STANDARD LOCATION) Receptacle, Remote Monitoring (RM) Plug, Remote Monitoring Cap and Tether, Receptacle Assembly 3 66U--683 Gasket, Remote Monitoring Receptacle Screw, Round Head, #--0 x /8 lg. -- SST 36 66U Washer, Flat, 0. ID -- SST Nut, Self Locking, # SST Plate, Switch, with RM A/R Plate, Switch, with RM NT--00 and up A/R Plate, Switch with RM and MDS, NT--00 and Up A/R REMOTE MONITORING (LOWER LEFT/EXTERNAL LOCATION) Receptacle, Remote Monitoring (RM) 0 69NT0-- Bracket OPTION F - CONDENSER FAN SWITCH Switch, Toggle (CFS) 66U--97 Seal, Bushing Plate, Switch (with extra switch location) HOURMETER 66U--383 Hourmeter 66U Screw, Pan Head, #--0 x 3/ lg. -- SST Bracket, Hourmeter 7 66U--38 Screw, Hex Head, #0-- x 0.0 lg. -- SST T-3PL

24 .9 CONTROL BOX - SINGLE EVAPORATOR FAN CAPABILITY, EBS, ED T-3PL 6

25 .9 CONTROL BOX - SINGLE EVAPORATOR FAN CAPABILITY, EBS, ED (Continued) SINGLE EVAPORATOR FAN CAPABILITY Screw, Pan Head, Thread Cutting #8--3 x 3/ lg. -- SST Contactor, (E & S) & (E & S) ( Amp) EMERGENCY BYPASS (EBS) Fuse, 0 Amp (FEB) Fuse Holder Emergency Bypass Module 6 66U Wire Tire 3 EMERGENCY DEFROST (ED) Holder Assembly, Fuse Fuse, Amp (FED) Plate, Switch (with light location, with RM) A/R Switch, Toggle Bracket Screw, Captive Washer, #0-- X 0.6 lg. -- SST Hex Nut 66U--97 Seal, Bushing Label, EB and ED Base,PilotLight 7 T-3PL

26 .0 CONTROL BOX - CONTROLLER MODULE SECTION AND SOFTWARE CARDS View - Back of Controller/DataCORDER T-3PL 8

27 .0 CONTROL BOX - CONTROLLER MODULE SECTION AND SOFTWARE CARDS (Continued) -- Module, Controller/DataCORDER -- RefertoSection-- Includes: -- 66U Screw, Hex Head, #0-- x / lg. -- SST 3 69NT3--69 Washer, Fender, Thick -- SST Retainer, Screw, 0. ID Fuse, 7. Amp (F3A & F3B) Fuse, Amp (F & F) Label, Controller/DataCORDER Port xx/3 Card, Controller/DataCORDER Operation Software SV Connector (EC A--K) Pin Socket, 0 AWG Socket, 8 AWG Plug, Sealing Connector (KE) -- Pin Connector (KB) -- 0 Pin NS Connector (KP) -- 9 Pin (Connects to Ribbon Cable) Connector (KD) -- Pin SV Connector (EC L--Y) Pin Connector (KC) -- 6 Pin Connector (KA) -- Pin Connector (MC) -- 8 Pin Connector (MB) -- 6 Pin Connector (MA) -- Pin NS Battery, Real Time Clock, (Within the Controller) NS Wire Harness, Controller to Current Sensing Transformer) NS Wire Harness, Display Module to Controller/DataCORDER Module NS Label, Warning, Don t use ! --(Located on the control box behind the Controller/DataCORDER module.) NS Label, Warning, xx Series -- (Located on the high & low voltage shields) NS Label, Warning, xx Series -- (Located on the bottom panel of the control box between the Communications Interface module and the switch panel.) OPTION R - RECHARGEABLE BATTERY PACK SV Battery Pack -- Controller/DataCORDER Module 9 T-3PL

28 . CONTROL BOX - DISPLAY MODULE AND COMMUNICATIONS INTERFACE MODULE SECTION 3 MANUAL DEFROST/ INTERVAL T-3PL 0

29 . CONTROL BOX - DISPLAY MODULE AND COMMUNICATIONS INTERFACE MODULE SECTION (Continued) RP Module, LCD Display (Option ) RP Module, LED Display (Option ) 66U Screw, Hex Head, #0-- x / lg. -- SST 3 69NT Washer, Fender, Thick -- SST Connector (MB) -- 6 Pin Connector (MK) -- 9 Pin Connector (CIC) -- 7 Pin Connector (CIB) -- 3 Pin Connector (CIA) -- 7 Pin NS Wire Harness, Key Pad to Display Module OPTION - COMMUNICATIONS INTERFACE MODULE - HIGH DATA RATE SV Module, Communications Interface -- Includes: 0 66U--3-- Stud, Fastener, / turn, 0.70 lg. -- SST 66U--9-- Retainer, Push--on Screw, Captive Washer #0-- x SST Retainer, Screw 0.7 OD OPTION - COMMUNICATIONS INTERFACE MODULE - LOW DATA RATE SV Module, Communications Interface -- Includes: 0 66U--3-- Stud, Fastener, / turn, 0.70 lg. -- SST 66U--9-- Retainer, Push--on Screw, Captive Washer #0-- x SST Retainer, Screw 0.7 OD T-3PL

30 . CONDENSER FAN MOTOR AND CONDENSER COIL SECTION 3 3 OPTION OR U Capscrew, Hex Head, /--0 x 3/ lg. -- SST 0 66U Washer, Flat, / -- SST Washer, Mylar, 3/ OD x / ID Washer, Mylar,.0 OD x / ID 69NT3--37 Bracket, Condenser Motor Mount Motor, Condenser Fan -- Includes: Bearing Capacitor, uf 9 PL Key, 3/6 Square x --3/8 lg. -- SST 0 66U--36 Screw, Hex Head, /6--8 x --/ lg. -- SST Washer, Flat, /6 -- SST Washer, Mylar,.0 OD x 3/8 ID Locknut, / SST 69NT3--6 Protector, Condenser Fan Motor Mounting Fan, Condenser (7 -/ diameter) -- Composite -- Includes: 6 PL Set Screw,Square Head, /6-- x /8 lg. -- SST T-3PL

31 . CONDENSER FAN MOTOR AND CONDENSER COIL SECTION (Continued) OPTION 3 - THREE ROW (7MM) CONDENSER COIL SV Cover, Condenser Coil, Blue Includes: SV Cover, Condenser Coil, White Includes: Bumper (for use with uncoated center handle) Plug (for use with coated handle or units with no center handle) SV Coil, Condenser(Copper) -- 7MM 3 Row -- Includes Mylar Washers 0 66CH Trim, Flexible 69NT Protector (Apply between frame and coil & coil cover) 69NT Protector (Apply between frame and coil & coil cover) Protector,Mylar (Apply between coil & coil cover, RH &LH sides) OPTION H - HINGED CONDENSER FAN GRILLE Grille and Venturi Assembly -- Includes: 66U--89 Label, Rotation Hinge Kit -- Includes: Hinge Protector, Mylar Screw, Hex Head, #0-- x 7/6 lg. -- SST U Screw, Retaining -- SST 66U Screw, Retaining (Phillips Head) -- SST Washer, Retaining -- SST Washer, Mylar, /ID x.00od 33 69NT Washer, Fender / -- SST OPTION B - BOLTED CONDENSER FAN GRILLE Grille and Venturi Assembly -- Includes: 66U--89 Label, Rotation 3 69NT Washer, Fender / -- SST Washer, Mylar, /ID x.00od Washer, Lock, / -- SST 37 66U Capscrew, Hex Head, /--0 x 3/ lg. -- SST 3 T-3PL

32 .3 COMPRESSOR TUBING SECTION T-3PL

33 .3 COMPRESSOR TUBING SECTION (Continued) Valve, Stepper Motor -- Includes: O--Ring Piston and Motor Assembly -- Includes: Connector (To Power Pack) NS Pin, 8--0 Gauge (Used on ) NS Seal (Used on ) Cap Clamp, Cushion, 0.88 Diameter 7 66U Screw, Hex Head, #0-- x 0.7 lg. -- SST Washer, Mylar, 0. ID x 0.80 OD Valve, Discharge Pressure Regulator (DPRV) 0 66U Clamp, Cushion,.8 Diameter 69NT--70 Bracket Assembly 66U Washer, Flat, #0 -- SST Washer, Mylar, 0.0 ID x 0.60 OD 3 -- Valve, Service (Discharge) -- See Section.3 -- Valve, Service (Suction) -- See Section Cap, M8 x.0 -- Nylon Elbow, Adapter (R3a) Tubing Assembly NS Socket (Used on -08-0) NS Pin (Used on ) NS Seal (Used on , and ) A/R NS Connector (On Harness to Drive) NS Pin (Used on ) REFRIGERANT TEMPERATURE SENSORS Sensor, Thermistor (CPSS) Sensor, Thermistor (CPDS) T-3PL

34 . RECEIVER SECTION T-3PL 6

35 . RECEIVER SECTION (Continued) Receiver Kit -- Includes: Receiver, Electro--Coated Modular, Copper Glass, Sight, w/red Balls, /-- NPT Indicator, Moisture--Liquid Plug, Fusible, 3/8 NPT -- Brass Disc, Rupture, 3/8 NPT -- Alternate 6 66U Screw, Hex Head, /--0 x 3/ lg. -- SST A/R 7 66U Washer, Flat, / -- SST Washer, Mylar, 0.0 ID x OD Protector, Mylar NS SV Connector, Female (Located on wire harness) Clamp, Cushion, / Diameter 66U Screw, Machine, Hex Head, #0-- x 0.7 lg. -- SST Washer, Mylar, 0.0 ID x 0.60 OD Valve, Liquid Line Clamp, Cushion, /8 Diameter Bracket, Liquid Line Valve Coupling, M -- Brass -- Includes: Cap, Service Port Cap, Service Valve 9 66U Bolt, Hex Head, 3/8--6 x.00 lg. -- SST 0 AUJR Washer, Lock, 3/8 -- SST 66U--3-- Washer, Flat, 3/8 -- SST Washer, Mylar, 0.37 ID x.00 OD 3 -- See Section.6 for Sensor Assembly and Related Parts SV Filter--Drier with O--Rings Transducer, Condenser Pressure (CPT) 6 EC39DM06 Valve, Schrader SV Sensor, Ambient Thermistor (AMBS) 8 69NT3--0 Bracket Assembly, Quench Valve Rivet, Blind, /3 Diameter, Grip Range -- /8--/ -- SST 30 66U--3-- Connector 3 66U Heat Shrink SV Valve, Quench, Thermostatic Expansion -- Includes: Clamp, Cushion, 0. Diameter Washer, Mylar, 0. ID x.00 OD NS Kit, Repair -- Includes: NS NSS Power Head 3 DE0BA03 Tee, Reducing / x / x 3/8 7 T-3PL

36 . WATER -COOLED CONDENSER SECTION NT--9 Kit, Condenser/Receiver (For Field Installation) -- See NOTE -- Includes: 69NT--9-- Condenser/Receiver -- Includes: Sight Glass, w/red balls, / NPT Protector, Mylar Protector, Mylar Coupling, Self Draining -- Includes: 6 66U Coupling Assembly, Socket -- Includes: Seal, O--Ring 8 66U-- Cap, Dust (Use with ) 9 66U-- Cap, Dust 0 66U Coupling (Water--In) Cap Assembly (Use with 66U ) Disc, Rupture, 3/8 NPT SV Switch,Water Pressure OPTION W T-3PL 8

37 . WATER -COOLED CONDENSER SECTION (Continued) Washer, Mylar, / ID x 3/6 OD 66U Washer, Flat, / -- SST 6 66U Capscrew, Hex Head, /--0 x 3/ lg. -- SST 7 66U Bolt, Hex Head, 3/8--6 x.00 lg. -- SST 8 AUJR Washer, Lock, 3/8 -- SST 9 66U--3-- Washer, Flat, 3/8 -- SST Washer, Mylar, 3/8 ID x.00 OD -- See Section.6 for Sensor Assembly and Related Parts Accessory Kit, Water--Cooled Condenser Tubing -- Includes: -- 69NT--87 Tube Assembly -- Includes: Indicator, Liquid Moisture -- Brass Bracket 66U Screw, Hex Head, #0-- x 3/ lg. -- SST Washer, Mylar, 0.0 ID x OD -- 69NT--97 Tube Assembly -- Includes: Valve, Liquid Line -- Includes: Cap, Flare -- / Cap, Valve Coupling, M -- Brass -- Includes: Cap, Service Port SV Filter--Drier with O--Rings 33 69NP0--03 Clamp, Filter--Drier -- Includes: NS Gasket (6 ft., Cut to length) 3 06DA03--8 Valve, Schrader Transducer, Condenser Pressure (CPT) 36 69NT--77 Tube Assembly -- Includes: Tee, / x / x 3/8 NPT -- Brass Washer, Mylar, 0. ID x.00 OD U Screw, Machine Hex Head, #0-- x 0.7 lg. -- SST Clamp, Cushion, 0.6 Diameter DE0BA03 Tee, Reducing, / x / x 3/ SV Valve, Quench, Thermostatic Expansion -- Includes: NS Kit, Repair -- Includes: NS NSS Power Head Clamp, Cushion, 0. Diameter 69NT3--0 Bracket Assembly Rivet, Blind, /3 Diameter, Grip Range -- /8--/ SV Sensor, Ambient Thermistor (AMBS) NOTE Must order tubing accessory kit when ordering P/N 69NT--9 for field installation on units provisioned for a water--cooled condenser. 9 T-3PL

38 .6 RRS AND RTS SECTION 3 3 (RTS) (RRS) SV Sensor Assembly (RTS & RRS) SV Cap, Probe -- Includes: Grommet NSS Cover, Probe Holder, Probe 6 66U Washer, Flat, / -- SST 7 66U Screw, Machine, Hex Head, #0-- x 0.0 lg. -- SST T-3PL 30

39 .7 THERMOSTATIC EXPANSION VALVE Valve, Thermostatic Expansions Insulation, Foam Formed, TXV Bulb 3 66U Wire Tie Tube, 0.0 OD Clamp, Tube 0.0 Diameter 6 66U Screw, TF Hex. Hd. #0--x.7 Lg Thread Cutting Clamp, Tube 0. Diameter Bracket Bracket, TXV Clamp, Tube 0.7 Diameter Plate, Cover Label, TXV Bulb 3 T-3PL

40 .8 UPPER FRESH AIR MAKE -UP AND ACCESS PANEL SECTION OPTION 3 6 OPTION OPTION OPTION.8 UPPER FRESH AIR MAKE -UP AND ACCESS PANEL SECTION OPTION EVAPORATOR FAN ACCESS PANEL - PLAIN SV Panel, Access (See NOTE) -- Includes: A/R Gasket Gasket, x 0.0 Halfmoon Washer, Mylar, / ID X 0.80 OD Washer, Flat, / -- SST Screw, Hex Head, /--0 x.00 lg. -- TIR U----8 Gasket, 0.7 x. x 6.63 T-3PL 3

41 .8 UPPER FRESH AIR MAKE -UP AND ACCESS PANEL SECTION (Continued) OPTION EVAPORATOR FAN ACCESS PANEL - WITH FRESH AIR MAKEUP Panel, Fresh Air Make--up w/retaining Washers -- Includes: A/R Gasket Gasket, x 0.0 Halfmoon Washer, Flat, / -- SST Washer, Mylar, / ID X 0.80 OD Screw, Hex Head, /--0 x.00 lg. -- TIR U----8 Gasket, 0.7 x. x Label, Fresh Air (See Section.36 for Language Selection) Gasket (One Piece) Label, Fresh Air Washer, Mylar,.00 OD x 0.3 ID 3 66U Washer, Flat, /6 -- SST 66U Nut, Wing, / SST Screw, Machine Pan Head, #8--3 x / lg. -- SST OPTION 3 WITH FRESH AIR MAKEUP AND SCREENS - USE ALL OF OPTION AND ITEM BELOW Screen, Medfly OPTION EVAPORATOR FAN ACCESS PANEL - WITH FRESH AIR MAKEUP AND VENT POSITION SENSOR (VPS) Panel (orange), Fresh Air Make--up w/vps -- Includes: A/R Panel (white), Fresh Air Make--up w/vps -- Includes: A/R Gasket Gasket, x 0.0 Halfmoon Washer, Mylar, / ID X 0.80 OD Washer, Flat, / -- SST Screw, Hex Head, /--0 x.00 lg. -- TIR U----8 Gasket, 0.7 x. x Label, Fresh Air (See Section.36 for Language Selection) Label, Fresh Air Washer, Mylar,.00 OD x 0.3 ID 3 66U Washer, Flat, /6 -- SST 66U Nut, Wing, / SST 33 T-3PL

42 .9 LOWER FRESH AIR MAKE -UP VENT OPTION OPTION -- & 3 3 OPTION -- OPTION - LOWER FRESH AIR (NONE) 69NT3--07 Panel, Blank 66U Screw, Hex Head, /--0 x 3/ lg. -- SST Washer, Mylar, / ID x.00 OD 3 66U Washer, Flat, /, Type A-- SST 3 69NT Bracket, Panel Gasket 7 69NT Washer, Fender / -- SST OPTION - INSTALLED 8 69NT--8-- Cover, Fresh Air Makeup -- Includes: Nut, Hex, /--0 UNC--B -- SST Nut, Hex, (with mini handle),/--0 UNC--B -- SST Washer, Mylar, / ID x.00 OD 69NT Cover Assembly, Air Bleed -- Includes: Gasket, Air Exchange T-3PL 3

43 .9 LOWER FRESH AIR MAKE -UP VENT (Continued) Gasket, Cover Gasket, Cover Label Kit -- Includes: Label, Air Exchange, CMH -- English 66CH Label, Arrow Label Kit -- Includes: 69NT3--7 Label, Air Exchange, CMH -- English (Maersk Specification) 66CH Label, Arrow (Maersk Specification) Label Kit -- Includes: 69NT Label, Air Exchange, CFM -- English/Spanish 66CH Label, Arrow Label Kit -- Includes: Label, Air Exchange, CMH -- English/Spanish/Chinese 66CH Label, Arrow Label Kit -- Includes: Label, Air Exchange, CMH -- English/Spanish/Chinese (NYK Specification) Label, Arrow (NYK Specification) U Washer, Flat, / -- SST 7 69NT--78 Bushing Nut, Hex, /--0 UNC--B -- SST A/R Nut, Hex, (with mini handle),/--0 UNC--B -- SST A/R 9 69NT Baffle, Unpainted Rivet, Blind, 0.6 Diameter, Grip Range -- 3/6--/ 69NT3--70 Label, Fresh Air 69NT Label, Fresh Air Exchange, CMH -- English (Maersk Specification) 69NT3--98 Label, Fresh Air Exchange, CFM -- English/Spanish Label, Fresh Air Exchange, CMH -- English/Japanese/Chinese Label, Fresh Air Exchange, CMH -- English OPTION 3 - INSTALLED WITH SCREENS - USE ALL OF OPTION PLUS ITEM BELOW Screen Assembly, Medfly OPTION - INSTALLED WITH VENT POSITION SENSOR Assembly, Vent Position Sensor -- Includes: Sensor Assembly -- Includes: Gear, 69NT, Auto LFA Screw, Set #8-- 3 X 0.6lg Nut, Hex Jam 3/ Washer, Lock 3/ Bracket, Thick SST Sensor, LVPS; Potentiometer 3 66U Screw, Hex Head 0-- x / gl. SST Nut, Hex, 0-- UNC--B -- SST 3 66U Washer, Flat, /, Type A-- SST Washer, Mylar Label, LVPS, Air Exchange Assembly, Slide 3 T-3PL

44 .0 EVAPORATOR FAN ASSEMBLY 9 6, 7, 8 9, 0, 3,, or 7, 3,, EFM- (Location) 3 EFM- (Location), , As viewed from front of unit, 3, T-3PL 36

45 .0 EVAPORATOR FAN ASSEMBLY (Continued) 69NT3-73 Bracket, Motor Mount Screw,Cap Hex Head /6--8 X Washer, Flat, / Nut, Self Lock, / Motor Assembly Upflow Efm - Includes: 6 66NS080CD000 Sleeve 7 69ND3--78 Connector Straight 8 69ND Nut,Lock 9 66U--7 Cap, Splice U----8 Cap, Insulator # Motor, Evaporator Two Speed Harness, EFM-- Includes: Connector Female Plug Seal Motor Assembly Upflow Efm - Includes: 6 66NS080CD000 Sleeve 7 69ND3--78 Connector Straight 8 69ND Nut, Lock 9 66U----7 Cap, Splice U----8 Cap,Insulator Motor, Evaporator Two Speed Harness, EFM-- Includes: Connector Female Plug Seal 8 66U-36-7 Bolt, Hex Head, 3/8-6 x.00 lg 8 9 AUJR Washer, Lock 3/8 Spring U-3- Washer, Plain 3/8 N Type A 8 66CH Fan, CW, EF-- 66CH Fan, CCW, EF NT3-66- Shim, (If Required) 69NU3--9 Label EFM-- 69NU Label EFM AC Arrow,Direction 7 66CH Label EF 8 66CH Label EF Protector 37 T-3PL

46 . EVAPORATOR COIL SECTION - REAR PANELS REMOVED SRS / STS T-3PL 38

47 . EVAPORATOR COIL SECTION - REAR PANELS REMOVED SV Sensor Assembly (SRS / STS) SV Sensor, Thermistor, Defrost (DTS) Screw, Hex Head, #8--3 x 3/ lg. -- SST (For mounting DTS) 3 66U Thermostat, Heat Termination (HTT) Screw, Hex Head, #8--3 x / lg. 6 66U Capscrew, Hex Head, /--0 x 3/ lg. -- SST Coil, Evaporator w/o Varnish Coil, Evaporator w Varnish 8 66U Washer, Plain /N Type A Washer, Lock / Spring 0 69NT Washer, Fender, / -- SST Heater, Evaporator Coil Retainer 3 66U Screw, Mach. HXHD /--0 x. Lg 3 -- USDA Option -- RefertoSection.3 -- NS 66U Tube, Heat Shrink -- / x --3/ lg. A/R 69NT Tube, Liquid Line Tube, Suction Line Clamp, Tube. Diameter 8 66U Screw, Mach. HexHd #0--x.7 Sltd Tube, Liquid Line Clamp, Tube 0.0 Diameter 66U Screw, TF HexHd #0--x.7 Thread Cutting Clamp, Tube. Diameter Tube, Suction Line OPTION 3 - EVAPORATOR COIL WITH HERMETIC TXV and LARGE HEAT EXCHANGER Heat Exchanger (Suction Line) Large OPTION - EVAPORATOR COIL WITH HERMETIC TXV and STANDARD HEAT EXCHANGER Heat Exchanger (Suction Line) Standard DEHUMIDIFICATION Kit, Humidity Sensor(Field installation, units provisioned for - See Unit Matrix) -- Includes: Sensor, Humidity (HS) 6 66U Screw, Hex Head, #0-- x.00 lg. -- SST 7 66U Washer, Flat, #0 -- SST Bracket Assembly, Humidity Sensor 39 T-3PL

48 . EVAPORATOR FAN DECK, 3,,,, 6, 7, 8, T-3PL 0

49 . EVAPORATOR FAN DECK Fan Deck Assy. Thk Alum Rivet,Blind.6 Dia NT Channel Assy Evap Motor 66--U Washer, Plain / N Type A Screw, Cap Hex Head /--0 X NT Washer,Fender / Od Screw,Cap Hxhd /--0 X Ty--Rap Base Mounting Tab (/6) 6 T-3PL

50 .3 USDA SECTION OPTION -- D OPTION -- V 9 0 OPTION OR T-3PL

51 .3 USDA SECTION (Continued) OPTION D Kit, USDA (For field installation, units provisioned for side -mounted -- USDA - See Unit Matrix) -- Includes: Plug, Sealing Receptacle (PR, PR, PR3, Cargo Probe ) (3 Pin) Receptacle, Interrogator (ICR) ( Pin) NS 69NT--99 Plate Assembly, USDA -- Includes: 69NT3--7 Cap, Dust, with Tether (3 Pin) 69NT3--76 Cap, Dust, with Chain ( Pin) Contact, Pin, #6 (Used with & ) 3 NS 69NT Door Assembly (Included and Used with REAR -mount USDA only) NS Plug, Interrogator Socket (ICR) ( Pin) OPTION V Plug, Sealing Receptacle (PR, PR, PR3, Cargo Probe ) (3 Pin) 69NT3--7 Cap, Dust, with Tether (3 Pin) Contact, Pin, #6 (Used with & ) Receptacle, Interrogator ( Pin) Cap, Dust, with Tether ( Pin) Socket, Contact (Silver Plated) A/R Socket, Contact (Gold Plated) A/R USDA PROBE KITS OPTION Sensor Assembly, 600 lg. (M) (USDA Probe) -- Includes: A/R Plug, Socket (PR, PR, PR3, Cargo Probe ) Contact, Socket, #6 (Used with & ) A/R OPTION Sensor Assembly, 0 lg. (3.M) (USDA Probe) -- Includes: A/R Sensor Assembly, 600 lg. (M) (USDA Probe) -- Includes: A/R Plug, Socket (PR, PR, PR3, Cargo Probe ) Contact, Socket, #6 (Used with & ) A/R NOTE Do not mix silver pins with gold pins and sockets. 3 T-3PL