Container Refrigeration. SERVICE PARTS LIST for 69NT to 199 Container Refrigeration Units. T--320PL Rev A -- Change 01/07

Transcription

1 r Container Refrigeration 8 7 SERVICE PARTS LIST for 9NT to 99 Container Refrigeration Units T--0PL Rev A -- Change 0/07

2 SERVICE PARTS LIST CONTAINER REFRIGERATION UNIT MODEL 9NT Series

3 TABLE OF CONTENTS INTRODUCTION... CONFIGURATION IDENTIFICATION... OPTION DESCRIPTIONS... ORDERING INSTRUCTIONS... LETTER DESIGNATIONS.... QUICK LIST -- Clamps, Filter-Drier, Fuses, Ty-Raps, and Wire Terminals.... REFRIGERATION UNIT ASSEMBLY.... Refrigeration Unit -- Area Locator.... Rain Gutters.... Handles.... Thermometer Port.... Control Box Door.... Control Box -- Composite Control Box -- Standard Electrical Components, Remote Monitoring and CFS Control Box -- Controller Module Section and Software Cards....9 Control Box -- Display Module and Communications Interface Module Section....0 Condenser Fan Motor, Condenser Coil, and Bolted or Hinged Grille Section.... Compressor Tubing Section Receiver Section Water--Cooled Condenser.... Economizer, Economizer Expansion Valve, Economizer Solenoid Valve, & Filter Drier Section. STS and SRS Section.... Oil Separator Section....7 Upper Fresh Air Makeup and Access Panels....8 Lower Fresh Air Makeup Vent Evaporator Fan Assembly and Transfresh Evaporator Coil Section.... USDA Option, Probe Kits.... Back Panel Assembly -- Aluminum Bolted.... Back Panel Assembly -- Aluminum Bolted with USDA Door Back Panel Assembly -- Aluminum Hinged Back Panel Assembly -- Stainless Steel Hinged.... Electronic Partlow Temperature Recorder Compressor Mounting Components and Guard Transducers....0 Cable Restraint Components (Bungy Cords and J--Hooks).... Voltage Cables (0V and 0V)... iii iii iii vi vi i T-0PL

4 TABLE OF CONTENTS (Continued). Autotransformer (With and Without CB and Transformer Bridge Unit) Labels and Decals INTERROGATOR AND ACCESSORIES.... Datareader.... Interrogator Receptacle.... COMPRESSOR -- SCROLL.... CONTROLLER/DATACORDER TOOLS... 8 PART NUMBER INDEX... Index T-0PL ii

5 INTRODUCTION INTRODUCTION The Carrier Transicold model 9NT0-- series units are of lightweight aluminum frame construction, designed to fit in the front of a container and serve as the container front wall. CONFIGURATION IDENTIFICATION Unit identification information is provided on a plate located near the compressor. The plate provides the unit model number, the unit serial number and the unit parts identification number (PID). The model number identifies the overall unit configuration while the PID provides information on specific optional equipment, factory provision to allow for field installation of optional equipment and differences in detailed parts. Configuration identification for the models covered herein is provided in the Carrier Transicold Container Unit Matrix at OPTION DESCRIPTIONS Various options may be factory or field fitted to the base unit. These options are listed in the tables and described in the following subparagraphs.. Battery The refrigeration controller may be fitted with standard replaceable batteries or rechargeable battery pack.. Dehumidification The unit may be fitted with a humidity sensor. This sensor allows setting of a humidity set point in the controller. In the dehumidification mode the controller will operate to reduce internal container moisture level.. Control Box The control box is composite material and may be fitted with a lockable door.. Temperature Readout The unit may be fitted with suction and discharge temperature sensors. The sensor readings may be viewed on the controller display.. Pressure Readout The unit is fitted with standard suction and discharge transducers. The transducer readings may be viewed on the controller display.. USDA The unit may be supplied with fittings for additional temperature probes which allow recording of USDA Cold Treatment data by the integral DataCORDER function of the Micro--Link refrigeration controller..7 Interrogator Units that use the DataCORDER function are fitted with interrogator receptacles for connection of equipment to download the recorded data. Two receptacles may be fitted, one accessible from the front of the container and the other mounted inside the container (with the USDA receptacles)..8 Remote Monitoring The unit may be fitted with a remote monitoring receptacle. This item allows connection of remote indicators for COOL, DEFROST and IN RANGE. Unless otherwise indicated, the receptacle is mounted at the control box location.9 Communications. The unit may be fitted with a communications interface module. The communications interface module is a slave module which allows communication with a master central monitoring station. The module will respond to communication and return information over the main power line. Refer to the ship master system technical manual for further information..0 Compressor The unit is fitted with a scroll compressor with either standard piping (equipped with suction, discharge, economizer and oil return service valves) or with semi--hermetic piping (equipped with suction, discharge and economizer service connections).. Condenser Coil Theunitisfittedwitharowcoilusing7mmtubing.. Autotransformer An autotransformer may be provided to allow operation on 90/0, phase, 0/0 hertz power. The autotransformer raises the supply voltage to the nominal 80/0 volt power required by the base unit. The autotransformer may also be fitted with an individual circuit breaker for the 0 volt power. If the unit is fitted with an autotransformer and communications module, the autotransformer will be fitted with a transformer bridge unit (TBU) to assist in communications.. Temperature Recorder The unit may be fitted with an electronic recorder manufactured by Partlow Corporation.. Gutters Rain gutters may be fitted over the control box and recorder section to divert rain away form the controls. The different gutters include standard length bolted gutters, extended length gutters and riveted gutters. iii T-0PL

6 . Handles The unit may be fitted with handles to facilitate access to stacked containers. These handles may included fixed handles (located at the sides of the unit) and/or a hinged handle at the center (attached to the condenser coil cover).. Thermometer Port The unit may be fitted with ports in the front of the frame for insertion of a thermometer to measure supply and/or return air temperature. If fitted, the port(s) will require a cap and chain..7 Water Cooling The refrigeration system may be fitted with a water cooled condenser. The condenser is constructed using copper--nickel tube for sea water applications. The water cooled condenser is in series with the air cooled condenser replaces the standard unit receiver. When operating on the water cooled condenser, the condenser fan is deactivated by either a water pressure switch or condenser fan switch..8 Back Panels Back panel designs that may be fitted include panels of aluminum and stainless steel. Panels may be fitted with access doors and/or hinge mounting..9 0 Volt Cable Various power cable and plug designs are available for the main 0 volt supply. The plug options tailor the cables to each customers requirements..0 0 Volt Cable Units equipped with an autotransformer require an additional power cable for connection to the 0 volt source. Various power cable and plug designs are available. The plug options tailor the cables to each customers requirements.. Cable Restraint Various designs are available for storage of the power cables. These options are variations of the compressor section front cover.. Upper Air (Fresh Air Make Up) The unit may be fitted with an upper fresh air makeup assembly. The openings may also be fitted with screens.. Controlled Atmosphere The units may be fitted with the TransFresh option. For information on the TransFresh system, contact TransFresh Corporation, P.O. Box 788, Salinas CA 990. Evaporator The unit is fitted with an evaporator coil and a hermetic thermal expansion valve.. Evaporator Fan Operation The units are fitted with Normal Evaporator Fan Operation, opening of an evaporator fan internal protector will shut down the unit..7 Labels Operating Instruction and Function Code listing labels will differ depending on the options installed. For example, additional operating instructions are required to describe start--up of a unit equipped with an autotransformer. Where the labels are available with additional languages, they are listed in the parts list..8 Plate Set Each unit is equipped with a tethered set of wiring schematic and wiring diagram plates. The plate sets are ordered using a seven digit base part number and a two digit dash number. (See Unit Matrix).9 Controller Two different controllers are available:. Remanufactured -- Controller is the equivalent of a new OEM controller and is supplied with a month warranty.. Repaired -- Controller has had previous faults repaired and upgraded with the latest software. Note: Repaired controllers are NOT to be used for warranty repairs only full OEM Remanufactured controllers are to be used. Controllers will be factory equipped with the latest version of operational software, but will NOT be configured for a specific model number and will need to be configured, at the time of installation or sale..0 Stepper Drive All the units covered by this manual have suction modulating valves which act to control system capacity. Units indicated as being fitted with stepper drive have digital control motors fitted to the suction modulating valve to open and close the valve in steps as required.. Condenser Grille Two styles of condenser grilles are available, direct bolted grilles and hinged grilles.. Lower Air (Fresh Air Make Up) The unit may be fitted with a lower fresh air makeup assembly. These assemblies are supplied in two designs, the standard design and the macro design. The openings may also be fitted with screens. T-0PL iv

7 OPTION LEGEND General - Feature Not Applicable X P Battery Codes S R Features that apply to model Factory Installation of Equipment to Allow Field Installation Control Box Codes C CL Standard (throw away) Cells Rechargeable Cells Composite Box Without Door Lock Pressure Readout Codes T USDA Codes D V Composite Box With Door Lock Factory Installed Pressure Transducers Option D Option V Option Option Interrogator Codes Left Straight Mount Right Mount Box Mount Left Mount Left Angled Mount Right Mount Communications Codes Standard HighDataRate Chipset Modem Low Data Rate Compressor Codes S SS Scroll Scroll with Semi--Hermetic Piping Condenser/Receiver Codes Four Row Coil Five Row Coil L AutoTransformer Codes Large Receiver Transformer Fitted Transformer With CB Fitted Transformer With CB and Receptical Transformer With CB and Transformer Bridging Unit Temperature Recorder Codes 7 Standard Electronic Partlow 8 Special Electronic Parlow 9 No Temperature Recorder 0 Electronic Partlow (Both) Gutter Codes Standard Length Bolted Gutters Extended Length Gutters Rivieted Gutters Handle Codes Two Side and One Center Two Side One Center One Right Side and Two Center Thermometer Port Codes Supply Air Port Return Air Port B Both Ports Water Cooling Codes W Water Pressure Switch F Condenser Fan Switch Back Panel Codes Bolted Panels Bolted Panels With USDA Door Bolted Panels With Probe Access Door Hinged Panels Hinged Stainless Steel Panels 0 Volt Cable Codes Option Option Option Option Option Option 7 Option 7 8 Option 8 9 Option 9 v T-0PL

8 0Volt Cable Codes Option Option Option Option Option Option 7 Option 7 8 Option 8 9 Option 9 0 Option 0 Cable Restraint Codes Cable Door Left Bungy Cord Only J--Hook Left and Right Bungy Cord Left Bungy Cord With Left Extended Guard Left & Right Bungy Cords With Extended Guards R Upper Air Codes Dummy Receptical No Upper Fresh Air Upper Fresh Air Installed Upper Fresh Air Installed With Screen Upper Fresh Air Installed With VPS Ordering Instructions Lower Air Codes No Lower Fresh Air Lower Fresh Air Installed Lower Fresh Air With Screen Installed Lower Fresh Air Installed With VPS Controlled Atmosphere TransFresh Carrier Transicold Everfresh System Arctic Mode Codes C L B Crankcase Heater Drainline Heater Both Crankcase Heater & Drainline Heater Condenser Grille Codes B H Evaporator Codes Bolted Grille Hinged Grille Helicox Hatched Streamline Coil Evaporator Fan Codes Normal Evaporator Fan Operation Label Codes English English / Spanish English / Traditional Chinese Emergency Bypass Codes B EB Emergency Bypass & Emergengy Defrost Emergency Bypass Only All orders and inquiries for parts must include: Parts Identification Number (PID), Model Number, Unit Serial Number, Part Number, Description of part as shown on list and Quantity required. Address all correspondence for parts to the following address: CARRIER TRANSICOLD DIVISION Replacement Components Group, TR-0 P.O. Box 80, Syracuse, New York or FAX to: () -778 Letter Designations The following letter designations are used to classify parts throughout this list: A/R = N/A = As Required Not Available NS NSS = = Not shown in illustration Not sold separately -- Order next higher assembly or kit PID = Parts Identification Number -- essential to identify unit configuration. PL SST = = Purchase Locally Stainless Steel Series unless otherwise specified. SV = Suffix SV -- added to part number designates service replacement part. T-0PL vi

9 QUICK LIST - CLAMPS, FILTER-DRIER, FUSE, TY-RAPS, WIRE TERMINALS AND REPLACEMENT UNIT FRAMES PART NO. DESCRIPTION Clamp, Tube, / -- SST Clamp, Tube, /8 -- SST Clamp, Tube, / -- SST Clamp, Tube, /8 -- SST Clamp, Tube, / -- SST Clamp, Tube, 7/8 -- SST Clamp, Tube, -/8 -- SST Clamp, Tube, -/ -- SST Clamp, Tube, -/8 -- SST Clamp, Tube, -/ -- SST Connector, Butt End, Wire Range -- to AWG Connector, Butt End, Wire Range -- to AWG Connector, Butt End, Wire Range -- to 0 AWG Connector, Closed End, Wire Range -- to AWG Connector, Closed End, Wire Range -- 8 to 0 AWG SV Filter-Drier -0-0 Fuse, Amp (F & F) -0-0 Fuse, 0 Amp (FEB) Fuse, 7. Amp (FA & FB) Ring Terminal, #, Wire Range -- to 0 AWG Ring Terminal, #0, Wire Range -- to 0 AWG Ring Terminal, /8, Wire Range -- to 0 AWG Ring Terminal, /, Wire Range -- to 0 AWG Ring Terminal, #0, Wire Range -- to AWG Ring Terminal, /, Wire Range -- to AWG Ring Terminal, #0, Wire Range -- to AWG Ring Terminal, /8, Wire Range -- to AWG -0-0 Spade Terminal, / x /, Wire Range -- to AWG Spade Terminal, /8, Wire Range -- to 0 AWG Spiral Wrap, / Diameter x ft. lg Spiral Wrap, / Diameter x ft. lg. U-80 Tube, Heat Shrink, / ID x -/8 lg. U-80- Tube, Heat Shrink, / ID x -/ lg Ty-Raps, -/ inches lg Ty-Raps,.00 inches lg Series Wire Markers Sealant, Pipe (Used to seal fittings on unit with R-a) Cleaner, Coil Paint, Compressor Touch-Up, Blue 9NT NT Unit Frame, Service Replacement Contact Carrier Replacement Components Group for application Change 0/07 T-0PL

10 REFRIGERATION UNIT ASSEMBLY. REFRIGERATION UNIT - AREA LOCATOR T-0PL

11 . REFRIGERATION UNIT - AREA LOCATOR Item Section Number Area Description Refer to Section.7 Upper Fresh Air Makeup & Access Panels Refer to Section. Thermometer Port Refer to Section. Labels and Decals Refer to Section.9 Evaporator Fan Assembly Refer to Section.0 Motor, Condenser Fan Refer to Section. Rain Gutters 7 Refer to Section.9 Box, Control 8 Refer to Section. Handles 9 Refer to Section.0 Coil, Condenser 0 Refer to Section. or. Receiver or Water-Cooled Condenser Refer to Sections.7 or Compressor Refer to Section.7 Guard, Compressor Refer to Section.0 Cable, Power Refer to Section.0 Plug, Power Refer to Section. Autotransformer Refer to Section.9 Transfresh 7 Refer to Section Interrogator and Accessories 8 Refer to Section. Temperature Recorder 9 Refer to Section.8 Lower Fresh Air Makeup T-0PL

12 . RAIN GUTTERS or or or OPTION - STANDARD LENGTH - BOLTED 9NT-987 Gutter, Rain (Bolted, Standard - Right Side) 9NT-997- Gutter, Rain (Bolted, Standard & Extended Length - Left Side) OPTION - EXTENDED LENGTH - BOLTED 9NT-997- Gutter, Rain (Bolted, Standard & Extended Length - Left Side) 9NT-88 Gutter, Rain (Bolted - Right Side) OPTION - RIVETED Gutter, Rain (Riveted - Right and Left Side). HANDLES OPTION - TWO SIDE, ONE CENTER 9NT-8 Handle, Fixed 9NT0-7- Handle, Hinged OPTION - TWO SIDE 9NT-8 Handle, Fixed OPTION - ONE CENTER 9NT0-7- Handle, Hinged OPTION - ONE SIDE, TWO CENTER 9NT-8 Handle, Fixed 9NT0-7- Handle, Hinged T-0PL

13 . THERMOMETER PORT OPTION - SUPPLY AIR PORT U-8 Cap & Chain Assembly Label OPTION - RETURN AIR PORT U-8 Cap & Chain Assembly Label OPTION B - SUPPLY AND RETURN PORTS & U-8 Cap & Chain Assembly & Label T-0PL

14 . CONTROL BOX DOOR - LCD and LED Displays Control Box Control Box Door HINGE ASSEMBLY - SECTIONAL VIEW DOOR ASSEMBLY - PARTIAL BACK VIEW T-0PL

15 . CONTROL BOX DOOR - LCD and LED Displays OPTION, LCD DISPLAY 9NT-88-7 Door Assembly, LCD Display, Includes: Gasket, Door SV Window and Gasket Assembly, Control Box Door -- Lexan Washer, Retaining -- SST U-8-8 Screw, Retaining, Panel, SST U-8- Screw, Retaining, Wing, SST Washer, Mylar, 0.0 ID x OD Hinge, Half Hinge, Half Pin Assembly, with Tether Retainer, Nut Protector, Mylar (Hinge) U-0- Screw, Truss Head, #0- x / lg. -- SST U-- Washer, Lock, #0 -- SST 7 U--8 Washer, Flat, #0 -- SST Washer, Mylar, 0.0 ID x 0.00 OD Pocket, Placard Locknut, Hex Head, #0- -- SST Rivet, Blind, /8 Diameter, Grip Range U-7-7 Screw, #0- x / lg. -- SST 0 U--8 Washer, Flat, #0 -- SST Door Strap Kit OPTION, LED DISPLAY Door Assembly, LED Display, Includes: Gasket, Door 9NT--0-- Window Foam, Double Coated Washer, Retaining -- SST U-8-8 Screw, Retaining, Panel, SST U-8- Screw, Retaining, Wing, SST Hinge, Half Hinge, Half Pin Assembly, with Tether Retainer, Nut U-0- Screw, Truss Head, #0- x / lg. -- SST Washer, Lock, #0 -- SST U--8 Washer, Flat, #0 -- SST Washer, Mylar, 0.0 ID x 0.00 OD Pocket, Placard Locknut, Hex Head, #0- -- SST Rivet, Blind, /8 Diameter, Grip Range U--8 Washer, Flat, #0 -- SST 7 T-0PL

16 . CONTROL BOX In Box OPTIONC&CL -COMPOSITEBOX T-0PL 8

17 . CONTROL BOX (Continued) -- Plate, Schematic & Diagram (Refer to T-00, Container Unit Matrix) U-0 Screw, Truss Head, #0- x / lg. -- SST 9NT-- Shield, High Voltage (Plastic) -- Includes: Hinge Rivet, Blind, /8 Diameter, Grip Range -- /8-/ -- SST Stud & Retainer Package -- Includes: NS NSS Stud, Fastener NS NSS Retainer, Fastener Stud Receptacle 8 9NT-- Shield, Low Voltage (Lexan) -- With Tether Label, Danger-High Voltage Control Box, Standard Composite 9NT-7 Bracket, Non--Locking 9NT-87 Bracket, Locking (See Note ) -0-0 Receptacle, Retaining Rivet, Blind, /8 Diameter, Grip Range - / - / Rivet, Blind, /8 Diameter, Grip Range - /8 - / (See Note ) U-0 Screw, Truss Head, #0- x / lg. -- SST NS SV Crack, Chip and Hole Repair Kit NS SV Insert Repair Kit -- Includes: -0-0 Insert x 9.9 mm (.90 x.90 in) /-0 Threads -- NSS Insert x. mm (. x.0 in) 0- Threads -- NSS Insert --. x 7. mm (.990 x.97 in) 0- Threads -- NSS Insert x 9. mm (.00 x.7 in) 0- Threads -- NSS Insert x 9.9 mm (.00 x.90 in) /-0 Threads -- NSS Insert x.7 mm (.7 x. in) 0-Threads -- NSS 0 NS Durabond Epoxy -- NSS NS Static Mixing Tube -- NSS NS Application Gun -- Required for Insert Repair NOTES. The bracket is bolted to the control box -- order 9NT-87 for locking bracket.. When 9NT-87 is used, , rivet, is to be used in the upper door location. 9 T-0PL

18 .7 CONTROL BOX - SHIELDS REMOVED, STD ELECTRICAL COMPONENTS, RM, CFS, EBS AND ED REMOTE MONITORING --- LOWER/EXTERNAL MTG OPTION F - CONDENSER FAN SWITCH Switch, Toggle (CFS) U-97 Seal, Bushing Plate, Switch (with extra switch location) OPTION - NORMAL EVAPORATOR FAN OPERATION See Items and for correct contactor placement Contactor, Compressor (CH) (0 Amp) Screw, Hex Head w/ Washer, #8- x /8 lg. - SST Contactors, (CF), (HR) & (EF & ES) ( Amp) SV Panel, Contactor - Includes: Spacer (Used with sheet metal control box only) T-0PL 0 Change 0/07

19 .7 CONTROL BOX - SHIELDS REMOVED, STANDARD ELECTRICAL COMPONENTS (Continued) Screw, Hex Head, Captive Washer /-0 x. lg. - SST Rivet, Blind, /8 Diameter, Grip Range - / - /8-0-0 Receptacle Switch, Toggle (On-Off) U-97 Seal, Bushing Switch, Toggle (MDS) (if equipped) Plate, Switch 9NT-98- Plate, Ground SV Transformer, Base Unit 8 U-7-7 Screw, Hex Head, #0- x / lg. - SST A/R 9 U--8 Washer, Flat, #0 - SST A/R Contact, Auxiliary Washer, Lock, # - SST U-78- Circuit Breaker - 0 vac, Amp, (CB) U-- Screw, Pan Head, #- x /8 lg. - SST 9NT-78 Bracket, Circuit Breaker Transformer, Current Sensing (CS) Screw, Captive Washer, #0- x. lg. - SST 7 CH-7- Trim, Flexible (8 Feet Long, Cut to Length) A/R SV Pad, Key -- Includes: 9 NSS Gasket (Between Key Pad Plate Assembly and Connector) 0 NSS Gasket (Between Key Pad and Key Pad Plate Assembly NSS Plate Assembly, Key Pad Mounting Screw, Pan Head, #0- X / lg. -- SST U--8 Washer, Plain, # Cover, Clear U-9- Screw, Pan Head (Thread Cutting), #8- x / lg. - SST Washer, Plain, #8 REMOTE MONITORING (STANDARD LOCATION) Receptacle, Remote Monitoring (RM) Plug, Remote Monitoring Cap and Tether, Receptacle Assembly 0 U-8 Gasket, Remote Monitoring Receptacle Screw, Round Head, #-0 x /8 lg. - SST U-- Washer, Flat, 0. ID - SST Nut, Self Locking, #-0 - SST Plate, Switch, with RM REMOTE MONITORING (LOWER LEFT/EXTERNAL LOCATION) Receptacle, Remote Monitoring (RM) 9NT0- Bracket EMERGENCY BYPASS Emergency Bypass Module Fuse, 0 Amp (FEB) Fuse Holder 0 U -7-0 Wire Tire Change 0/07 T-0PL

20 .8 CONTROL BOX - CONTROLLER MODULE SECTION AND SOFTWARE CARDS View - Back of Controller/DataCORDER T-0PL

21 .8 CONTROL BOX - CONTROLLER MODULE SECTION AND SOFTWARE CARDS -- Module, Controller/DataCORDER -- RefertoSection-- Includes: -- U-7-7 Screw, Hex Head, #0- x / lg. -- SST 9NT-9 Washer, Fender, 0.0 Thick -- SST Retainer, Screw, 0. ID Fuse, 7. Amp (FA & FB) -0-0 Fuse, Amp (F & F) Label, Controller/DataCORDER Port xx/ Card, Controller/DataCORDER Operation Software SV Connector (EC A-K) -- 0 Pin Socket, 0 AWG Socket, 8 AWG Plug, Sealing SV Connector (EC L-Y) -- 0 Pin -0-0 Connector (KA) -- Pin -0-0 Connector (KB) -- 0 Pin NS -0- Connector (KP) -- 9 Pin (Connects to Ribbon Cable) Connector (KD) -- Pin Connector (KE) -- Pin Connector (KC) -- Pin Connector (MA) -- Pin Connector (MB) -- Pin Connector (MC) -- 8 Pin NS SV Battery, Real Time Clock, (Within the Controller) NS Wire Harness, Controller to Current Sensing Transformer) NS Wire Harness, Display Module to Controller/DataCORDER Module NS Label, Warning, Don t use -007! --(Located on the control box behind the Controller/DataCORDER module.) NS Label, Warning, xx Series -- (Located on the high & low voltage shields) NS Label, Warning, xx Series -- (Located on the bottom panel of the control box between the Communications Interface module and the switch panel.) OPTION R - RECHARGEABLE BATTERY PACK SV Battery Pack -- Controller/DataCORDER Module Change 0/07 T-0PL

22 .9 CONTROL BOX - DISPLAY MODULE AND COMMUNICATIONS INTERFACE MODULE SECTION MANUAL DEFROST/ INTERVAL T-0PL

23 .9 CONTROL BOX - DISPLAY MODULE AND COMMUNICATIONS INTERFACE MODULE SECTION RP Module, LCD Display (Option ) RP Module, LED Display (Option ) Screw, Hex Head, #0- x / lg. -- SST -0-0 Connector (MK) -- 9 Pin Connector (MB) -- Pin Connector (CIC) -- 7 Pin Connector (CIB) -- Pin Connector (CIA) -- 7 Pin NS Wire Harness, Key Pad to Display Module OPTION - COMMUNICATIONS INTERFACE MODULE - HIGH DATA RATE SV Module, Communications Interface -- Includes: 9 U-- Stud, Fastener, / turn, 0.70 lg. -- SST 0 U-9- Retainer, Push-on Screw, Captive Washer #0- x SST Retainer, Screw.7 O.D. OPTION - COMMUNICATIONS INTERFACE MODULE - LOW DATA RATE SV Module, Communications Interface -- Includes: 9 U-- Stud, Fastener, / turn, 0.70 lg. -- SST 0 U-9- Retainer, Push-on Screw, Captive Washer #0- x SST Retainer, Screw.7 O.D. T-0PL

24 .0 CONDENSER FAN MOTOR AND CONDENSER COIL SECTION 9 OPTION OR OPTION OR U-- Capscrew, Hex Head, /-0 x / lg. -- SST 0 U--7 Washer, Flat, / -- SST Washer, Mylar, / OD x / ID Washer, Mylar,.0 OD x / ID SV Pigtail Connector Bracket, Condenser Motor Mount Motor, Condenser Fan -- Includes: 8 PL Key, / Square x -/8 lg. -- SST Bearing Capacitor, uf U- Screw, Hex Head, /-8 x -/ lg. -- SST Washer, Flat, / -- SST Washer, Mylar,.0 OD x /8 ID Locknut, /-8 -- SST 9NT- Protector, Condenser Fan Motor Mounting Fan, Condenser (7-/ diameter) -- Composite -- Includes: 7 PL Set Screw,Square Head, /- x /8 lg. -- SST T-0PL

25 .0 CONDENSER FAN MOTOR AND CONDENSER COIL SECTION (Continued) OPTION -FOUR ROW (7MM) CONDENSER COIL SV Cover, Condenser Coil, Blue Includes: 8--0SV Cover, Condenser Coil, White Includes: Plug (for use with coated handle or units with no center handle) SV Coil, Condenser(Copper) -- 7MM Row -- Includes Mylar Washers CH-7- Trim, Flexible 9NT-89-8 Protector (Apply between frame and coil & coil cover) 9NT-89-9 Protector (Apply between frame and coil & coil cover) Protector,Mylar (Apply between coil & coil cover, RH &LH sides) OPTION - FIVE ROW (/8 ) CONDENSER COIL Cover, Condenser Coil, Blue Includes: Cover, Condenser Coil, White Includes: Plug (for use with coated handle or units with no center handle) SV Coil, Condenser(Copper) -- row -- Includes Mylar Washers 7 CH-7- Trim, Flexible 8 9NT-89- Protector (Apply between frame and coil & coil cover) 9 9NT-89- Protector (Apply between frame and coil & coil cover) Protector,Mylar (Apply between coil & coil cover, RH &LH sides) OPTION H - HINGED CONDENSER FAN GRILLE Grille and Venturi Assembly, Blue -- Includes: Grille and Venturi Assembly, White -- Includes: U-89 Label, Rotation Hinge Kit -- Includes: Hinge Protector, Mylar Screw, Hex Head, #0- x 7/ lg. -- SST 8 7 U-8-8 Screw, Retaining -- SST U-8- Screw, Retaining (Phillips Head) -- SST Washer, Retaining -- SST Washer, Mylar, /ID x.00od 0 9NT-9- Washer, Fender / -- SST OPTION B - BOLTED CONDENSER FAN GRILLE Grille and Venturi Assembly, Blue -- Includes: Grille and Venturi Assembly, White -- Includes: U-89 Label, Rotation 9NT-9- Washer, Fender / -- SST Washer, Mylar, /ID x.00od -00- Washer, Lock, / -- SST U-- Capscrew, Hex Head, /-0 x / lg. -- SST 7 T-0PL

26 . COMPRESSOR TUBING SECTION Units with Standard Tubing Units with Semi -Hermetic Tubing T-0PL 8

27 . COMPRESSOR TUBING SECTION Common Components Washer, Mylar,. I.D. x.80 O.D Clamp, Cushion,. Dia Seal /- (See Section ) Elbow, Adapter, Brass Cap, M8 x.0 -- Nylon Coupling, Oil Return 7 U--0 Clamp, Cushion,.88 Dia Clamp, Cushion,.8 Dia. 9 U-7- Screw, Hex Head, #0- x.7 lg. -- SST Strainer Seal - (See Section ) Tubing Protector Standard Tubing Components Cap, Service Valve Elbow, Adapter, High Pressure, Ra -- Brass Cap, M0 x.0 -- Nylon Valve, Service 7/8 I.D Valve, Service /8 I.D Valve, Service /8 I.D Valve, Service /8 I.D. Semi -Hermetic Tubing Components 0 U Wire Tie Tube, Slit Economizer Tubing Assembly with Fitting Suction Tubing Assembly with Fitting Discharge Tubing Assembly with Service Fitting Oil Return Tubing Assembly with Fitting REFRIGERATION TEMPERATURE SENSORS Sensor, Thermistor (CPDS) Sensor, Thermistor (CPSS) See Section.0 9 T-0PL

28 . RECEIVER SECTION STANDARD RECEIVER - USE OPTION L AND SUBSTITUTE ITEM BELOW FOR NS Receiver Assembly OPTION L Large Receiver Assembly -- Includes: Glass, Sight Indicator, Moisture-Liquid -00- Plug, Fusible, /8 npt -- Brass Protector, Mylar U-- Screw, Hex Head, /-0 x / lg. -- SST 7 U--7 Washer, Flat, / -- SST Washer, Mylar Sensor, Ambient Thermistor (AMBS) 0 -- See Section. for Sensor Assembly and Related Parts -- T-0PL 0

29 . WATER -COOLED CONDENSER SECTION Kit, Condenser/Receiver (For Field Installation) -- Includes: 9NT-9- Condenser/Receiver -- Includes: Sight Glass, w/red balls, / npt Protector, Mylar Protector, Mylar U-7- Coupling (Water-In) U- Cap, Dust Coupling, Self Draining -- Includes: Seal, O-Ring 9 U- Cap, Dust SV Switch,Water Pressure OPTION W U-- Connector U-80 Heat Shrink Disc, Rupture, /8 npt Sensor, Ambient Thermistor (AMBS) -- See Section. for Sensor Assembly and Related Parts Indicator, Liquid Moisture -- Brass Tee, / X / X /8 NPT -- Brass Bracket (Style ) Bracket (Style ) 0 U-7- Screw, Hex Head, #0- x / lg. -- SST 9NT-9 Washer, Fender Nut, Self-Lock, #0- -- SST Washer, Mylar,.0 I.D. x.0 O.D. U--8 Washer, Plain, #0 -- SST Clamp, Cushion, / Diameter T-0PL

30 . ECONOMIZER, ECONOMIZER EXPANSION VALVE, ECONOMIZER SOLENOID VALVE AND FILTER DRIER SECTION T-0PL

31 . ECONOMIZER, ECONOMIZER EXPANSION VALVE, ECONOMIZER SOLENOID VALVE AND FILTER DRIER SECTION Cover Washer, Mylar, 0.0 ID x OD 8 U-- Screw, Hex Head, /-0 x.7 lg. -- SST U--7 Washer, Flat, / -- SST Nut, Self-Lock Coupling with Cap SV Filter-Drier -- Includes: SV O-Ring Clamp, Cushion,. Diameter Washer, Mylar,.0 I.D. x.0 O.D. 9 U-7-7 Screw, Machine, Hex Head, #0- x.0 lg. -- SST Bracket U--8 Washer, Plain #0 -- SST U-- Connector U-80 Heat Shrink Coil, Solenoid Valve (Oil Return and Economizer) 7 DE0BA0 Tee, Reducing / x / x / Clamp, Cushion,.0 Diameter Bracket Bracket Insulation, Economizer Tee Bracket U-- Washer, Plain, / N Type A -- SST Bracket U-7 Screw, Machine, Hex Head, #8- x.0 lg. -- SST 7 U-- Washer, Plain #8 -- SST 8 U-- Washer, Lock, #8 Spring -- SST 9 9NT-9- Washer, Fender Coil, Solenoid Valve Solenoid Valve Body Economizer Bushing 9NT-9- Washer, Fender #0 -- SST Solenoid Valve Body Expansion Valve Clamp, Cushion,. Diameter Valve, King Bracket, Blue Bracket, White Insulation, Economizer Gasket,.0 x.0 9NP0--0 Clamp, Tube,.88 diameter U--7-- Screw, Machine, Hex Head, #0-- x.7 lg.-- SST Plate T-0PL

32 . SRS AND STS SECTION (STS) (SRS) SV Sensor Assembly (STS & SRS) SV Cap, Probe -- Includes: Grommet NSS Cover, Probe Holder, Probe U--7 Washer, Flat, / -- SST 7 U-7-7 Screw, Machine, Hex Head, #0- x.0 lg. -- SST T-0PL

33 . OIL SEPARATOR SECTION Washer, Mylar, 0.0 ID x OD U-- Screw, Hex Head, /-0 x.7 lg. -- SST U--7 Washer, Flat, / -- SST Protector, Mylar SV Oil Separator Includes: Tubing 7 U-7 Screw, Machine, Hex Head, #8- x.0 lg. -- SST 8 U-- Washer, Plain #8 -- SST 9 U-- Washer, Lock, #8 Spring -- SST Solenoid Valve U-- Connector U-80 Heat Shrink Coil, Solenoid Valve T-0PL

34 .7 UPPER FRESH AIR MAKE-UP AND ACCESS PANEL SECTION 7 8 FRESH AIR PANEL WITH VPS BACK OF FRESH AIR PANEL UPPER FRESH AIR MAKE-UP AND ACCESS PANEL SECTION OPTION EVAPORATOR FAN ACCESS PANEL - PLAIN SV Panel, Access (See NOTE ) -- Includes: A/R Gasket Gasket, x 0.0 Halfmoon Washer, Flat, / -- SST Washer, Mylar, / ID X 0.80 OD Screw, Hex Head, /-0 x.00 lg. -- TIR 8 7 U--8 Gasket, 0.7 x. x. T-0PL

35 OPTION EVAPORATOR FAN ACCESS PANEL - WITH FRESH AIR MAKEUP Panel, Fresh Air Make--up w/retaining Washers -- Includes: A/R Gasket Gasket, x 0.0 Halfmoon 7 U--8 Gasket, 0.7 x. x Label, Fresh Air (See Section. for Language Selection) Label, Fresh Air Washer, Mylar,.00 OD x 0. ID U-- Washer, Flat, / -- SST U-- Nut, Wing, /-8 -- SST OPTION WITH FRESH AIR MAKEUP AND SCREENS - USE ALL OF OPTION AND ITEM BELOW Screen, Medfly OPTION EVAPORATOR FAN ACCESS PANEL - WITH FRESH AIR MAKEUP AND VENT POSITIONING SENSOR (VPS) Panel, Fresh Air Make--up w/vps -- Includes: A/R Gasket Gasket, x 0.0 Halfmoon 7 U--8 Gasket, 0.7 x. x Label, Fresh Air (See Section. for Language Selection) Label, Fresh Air Washer, Mylar,.00 OD x 0. ID U-- Washer, Flat, / -- SST U-- Nut, Wing, /-8 -- SST HEATER ACCESS PANEL SV Panel, Access -- Includes: Gasket Gasket, Access Panel Washer, Flat, / -- SST Washer, Mylar, / ID X 0.80 OD Screw, Hex Head, /-0 x.00 lg. -- TIR 8 STUD ASSEMBLY KITS (REPLACEMENT) Kit, Gasket and Stud Assembly (See NOTE ) -- Includes: Gasket (One Piece) Kit, Disc and Stud Assembly (See NOTE ) -- Includes: 9 NSS Stud Assembly, / Screw, Machine Pan Head, #8- x / lg. -- SST Washer, Mylar,.00 OD x 0. ID U-- Washer, Flat, / -- SST U-- Nut, Wing, /-8 -- SST NOTES. Access panels with Transfresh option should be ordered from Transfresh, See Section.9 for address.. Disc and stud assembly kit, which will modify stud to /-8, also includes new disc and gasket.. Must order stud assembly kit, which will modify stud to /-8, and include ( piece) gasket. 7 T-0PL

36 .8 LOWER FRESH AIR MAKE-UP VENT 8 OPTION OPTION -- & T-0PL 8

37 .8 LOWER FRESH AIR MAKE-UP VENT OPTION - LOWER FRESH AIR (NONE) 9NT-07 Panel, Blank (Blue) 9NT Panel, Blank (White) 9NT-07 Bracket, Panel U-- Screw, Hex Head, /-0 x / lg. -- SST Washer, Mylar, / ID x.00 OD U-- Washer, Flat, /, Type A-- SST 9NT-9- Washer, Fender / -- SST Gasket OPTION - INSTALLED 8 9NT-8- Cover, Fresh Air Makeup -- Includes: 9 9NT0-97- Cover Assembly, Air Bleed -- Includes: Gasket, Air Exchange 9NT-7 Label, Air Exchange, CMH -- English 9NT-98 Label, Air Exchange, CMF -- English/Spanish Nut, Hex, /-0 UNC-B -- SST Nut, Hex, (with mini handle),/-0 UNC-B -- SST Washer, Mylar, / ID x.00 OD Gasket, Cover Gasket, Cover CH-00- Label, Arrow 7 9NT-78 Bushing 8 9NT-87- Label, Fresh Air Exchange -- English 9 9NT-70 Label, Fresh Air 0 U--7 Washer, Flat, / -- SST Nut, Hex, /-0 UNC-B -- SST A/R 9NT-88 Baffle, Unpainted Rivet, Blind,. Diameter, Grip Range -- /-/ OPTION - INSTALLED WITH SCREENS - USE ALL OF OPTION PLUS ITEM BELOW Screen Assembly, Medfly 9 T-0PL

38 .9 EVAPORATOR FAN ASSEMBLY AND CONTROLLED ATMOSPHERE - TRANSFRESH SECTION EFM- (Location) EFM- (Location) 7 8 Upper back left of unit w/ evap fan assembly removed Partial view of the lower left corner of the unit. T-0PL 0

39 .9 EVAPORATOR FAN ASSEMBLY AND CONTROLLED ATMOSPHERE - TRANSFRESH SECTION 9NT-9 Mounting Bracket, Evaporator Fan Assembly 9NT-9- Washer, Fender Washer, Lock, / -- SST Screw, Hex Head, /-0 x -/ lg. -- SST Nut, Self Locking, / SST Washer, Special, /8 -- SST Fan, Evaporator Stator, Evaporator Protector -- Mylar Motor, Evaporator Fan -- Includes: NS Bearing, Front (Shaft End) NS Capacitor (0 µf) High Speed NS -0- Pin # NS Plug Assembly, Motor (Located on Wire Harness) -- Includes: NS -0-0 Plug NS -0- Contacts A/R NS Receptacle Assembly, Motor -- Includes: NS -0-0 Receptacle NS -0-0 Strain Relief NS -0- Contacts A/R U-- Washer, Flat, / -- SST Screw, Hex Head, /-0 x -/8 lg. -- SST 8 CONTROLLED ATMOSPHERE - TRANSFRESH Kit, Transfresh Field Installation (For units with NO Transfresh Provision) Includes: Screw, Hex Head, /-0 x -/ lg. -- SST 9NT-8 Bracket NS Pipe Assembly, PVC * 9NT-87- Cable Assembly, Transfresh Communications Connector (TCC) * 9NT-87- Panel Assembly, Transfresh *7 9NT-87- Cable, Power -- AC (Transfresh) *8 9NT-87- Hose Assembly, Air (Transfresh) *NS 9NT-87- Cable Assembly, Rear (Transfresh) *NS 9NT-87- Fuse Assembly, In-line (Transfresh) NOTE * Contact -- TransFresh Corp., P.O. Box 788, Salinas, CA 990 to order these parts. T-0PL

40 .0 EVAPORATOR COIL SECTION - REAR PANELS REMOVED (RTS & RRS) T-0PL

41 .0 EVAPORATOR COIL SECTION - REAR PANELS REMOVED SV Sensor Assembly (RRS & RTS) -- Sensor, Thermistor, (Temperature Recorder) Sensor, Thermistor, Defrost (DTS) Screw, Hex Head, #8- x / lg. -- SST U-9- Thermostat, Heat Termination (HTT) AUJR7 Washer, Lock, / -- SST 0 7 9NT- Retainer (For Heaters) 8 9NT- Clip (For Heaters) 9 9NT-9- Washer, Flat, / -- SST 0 U-7- Screw, Hex Head, #0- x. lg. -- SST U-- Capscrew, Hex Head, /-0 x / lg. -- SST 9 U-- Washer, Flat, / -- SST A/R -00-0SV Valve, Quench Expansion Heater, Evaporator Coil Heater, Drain Pan Clamp, Tube -- Nylon 7 U-7- Screw, Hex Head, #0- x.7 lg. -- SST 8 U--8 Washer, Flat, #0 -- SST 9 -- USDA Option -- RefertoSection Plug, Hole ( inch diameter) (Located on Fan Deck) Sensor, Thermistor, (CPSS) Protector, Mylar KAFA8 Clamp,Tube/8Holes U-7-7 Screw, Machine, Hex Head, #0- x.0 lg. - SST Valve, Stepper Motor -- Includes: Piston and Motor Assembly -- Includes: Connector (To Expansion Controller Module) NS Pin, 8-0 Gauge (Used on -09-0) NS Seal (Used on -09-0) OPTION HELICOX HATCHED Coil, Evaporator (Does not include thermostats or heaters) Units with PID Numbers NT08,NT08 and NT08 ONLY Coil, Evaporator (Does not include thermostats or heaters) Valve, Thermostatic Expansion, Hermetic DEHUMIDIFICATION Kit, Humidity Sensor(Field installation, units provisioned for - See Unit -- Matrix) -- Includes: Sensor, Humidity (HS) U-7-0 Screw, Hex Head, #0- x.00 lg. -- SST U--8 Washer, Flat, #0 -- SST Bracket Assembly, Humidity Sensor T-0PL

42 . USDA SECTION OPTION -- D 8 7 OPTION -- V 9 0 OPTION OR T-0PL

43 . USDA OPTION OPTION D Plug, Sealing Receptacle (PR, PR, PR, Cargo Probe ) ( Pin) Receptacle, Interrogator (ICR) ( Pin) NS 9NT-99 Plate Assembly, USDA -- Includes: 9NT-7 Cap, Dust, with Tether ( Pin) 9NT-7 Cap, Dust, with Chain ( Pin) -0- Contact, Pin, # (Used with & -00-0) NS Plug, Interrogator Socket (ICR) ( Pin) OPTION V Plug, Sealing Receptacle (PR, PR, PR, Cargo Probe ) ( Pin) 9NT-7 Cap, Dust, with Tether ( Pin) -0- Contact, Pin, # (Used with & -00-0) Receptacle, Interrogator ( Pin) Cap, Dust, with Tether ( Pin) Socket, Contact (Silver Plated) A/R Socket, Contact (Gold Plated) A/R FIELD INSTALLED KITS (for units with USDA provision, see T -00 ) Kit, USDA (For field installation, units provisioned for rear-mounted -- USDA - See T-00) -- Includes all of OPTION D and the following: NS 9NT0-07- Door Assembly (Included and Used with REAR-mount USDA only) Kit, USDA (For field installation, units provisioned for side-mounted USDA - See T-00) -- Includes all of OPTION D: -- USDA PROBE KITS OPTION Sensor Assembly, 00 lg. (M) (USDA Probe) -- Includes: A/R Plug, Socket (PR, PR, PR, Cargo Probe ) -0- Contact, Socket, # (Used with & -00-0) A/R OPTION Sensor Assembly, 0 lg. (.M) (USDA Probe) -- Includes: A/R Sensor Assembly, 00 lg. (M) (USDA Probe) -- Includes: A/R Plug, Socket (PR, PR, PR, Cargo Probe ) -0- Contact, Socket, # (Used with & -00-0) A/R NOTE Do not mix silver pins with gold pins and sockets. T-0PL

44 . BACK PANEL ASSEMBLY - OPTION - ALUMINUM BOLTED T-0PL

45 . BACK PANEL ASSEMBLY - OPTION - ALUMINUM BOLTED 9NT- Grille, Top (Unpainted) Rivet, Blind, / Diameter, Grip Range -- /8-/ U-798- Rivet, TIR, / Diameter, Grip Range -- /-/ 9NT-9- Panel Assembly, Upper PID Number 099 and below -- Includes: NS NSS Drain Pan, Side (Location -- Behind upper panel) NS NSS Drain Pan, Center (Location -- Behind upper panel -- Top) Gasket (Location -- Behind upper panel) Panel Assembly, Upper PID Number 0700 and above -- Includes: NS NSS Drain Pan (Location -- Behind upper panel) Gasket (Location -- Behind upper panel) NS U-807 Gasket ( ft., Cut to length) A/R Rivet, Blind, /8 Diameter, Grip Range -- /8-/ Rivet, Blind, /8 Diameter, Grip Range -- /-/ Panel, Bottom, (Painted) Panel, Bottom, (Unpainted) Panel, Bottom (Provision for heat exchanger location), (Painted) Panel, Bottom (Provision for heat exchanger location), (Unpainted) 0 U-0 Screw, Machine, Truss Head, #0- x / lg. -- SST 0 9NT-9 Washer, Fender, #0 x.00 OD -- SST 0 9NT-7 Duct, Air Label, Carrier Transicold 7 T-0PL

46 . BACK PANEL ASSEMBLY - OPTION - ALUMINUM BOLTED WITH USDA DOOR T-0PL 8

47 . BACK PANEL ASSEMBLY - OPTION - ALUMINUM BOLTED WITH USDA DOOR 9NT- Grille, Top Rivet, Blind, / Diameter, Grip Range -- /8-/ 7 U-798- Rivet, TIR, / Diameter, Grip Range -- /-/ 9NT-9- Panel Assembly, Upper PID Numbers 099 and below-- Includes: NS NSS Drain Pan, Side (Location -- Behind upper panel) NS NSS Drain Pan, Center (Location -- Behind upper panel) Gasket (Location -- Behind upper panel) Panel Assembly, Upper PID Numbers 0700 and and above -- Includes: NS NSS Drain Pan (Location -- Behind upper panel) Gasket (Location -- Behind upper panel) Rivet, Blind, /8 Diameter, Grip Range -- /8-/ Rivet, Blind, /8 Diameter, Grip Range -- /-/ Panel, Bottom Panel, Bottom (Provision for heat exchanger location) 0 U-0 Screw, Machine, Truss Head, #0- x / lg. -- SST 8 9NT-9 Washer, Fender, #0 x.00 OD -- SST 8 NS U-807 Gasket ( ft., Cut to length) A/R 9NT0-7- Door Assembly, Access-- Includes: Hinge 9NT-7- Spacer, Hinge Washer, Retaining Stud, / Turn, 0.97 lg Rivet, Blind, /8 Diameter, Grip Range -- /-/ Label, Carrier Transicold 9 T-0PL

48 . BACK PANEL ASSEMBLY - OPTION - ALUMINUM HINGED T-0PL 0

49 . BACK PANEL ASSEMBLY - OPTION - ALUMINUM HINGED 9NT- Grille, Top Rivet, Blind, / Diameter, Grip Range -- /8-/ 7 9NT-9- Panel Assembly, Upper PID Number 099 and Below -- Includes: NS NSS Drain Pan, Side NS NSS Drain Pan, Center Gasket (Location -- Behind upper panel) Panel Assembly, Upper PID Number 0700 and Above -- Includes: NS NSS Drain Pan Gasket (Location -- Behind upper panel) Rivet, Blind, /8 Diameter, Grip Range -- /8-/ Rivet, Blind, /8 Diameter, Grip Range -- /-/ Panel, Bottom, (Painted) Panel, Bottom, (Unpainted) Panel, Bottom (Provision for USDA location), (Painted) Panel, Bottom (Provision for USDA location), (Unpainted) NS U-807 Gasket ( ft., Cut to length) A/R 9 9NT-8 Hinge Washer, Retaining Stud, / Turn,.0 lg Stud, / Turn, 0.9 lg Receptacle, Retaining T-0PL

50 . BACK PANEL ASSEMBLY - OPTION - STAINLESS STEEL HINGED T-0PL

51 . BACK PANEL ASSEMBLY - OPTION - STAINLESS STEEL HINGED 9NT- Grille, Top Rivet, Blind, / Diameter, Grip Range -- /8-/ 7 9NT-9- Panel Assembly, Upper PID Number 099 and Below -- Includes: NS NSS Drain Pan, Side NS NSS Drain Pan, Center Gasket (Location -- Behind upper panel) Panel Assembly, Upper PID Number 0700 and Above-- Includes: NS NSS Drain Pan, Gasket (Location -- Behind upper panel) Rivet, Blind, /8 Diameter, Grip Range -- /8-/ Rivet, Blind, /8 Diameter, Grip Range -- /-/9 7 9NT-98 Panel, Bottom. SST 8 9NT-98- Panel, Bottom (Provision for USDA location), SST NS U-807 Gasket ( ft., Cut to length) A/R 9 9NT-8 Hinge Washer, Retaining Stud, / Turn,.0 lg Stud, / Turn, 0.9 lg Receptacle, Retaining T-0PL

52 . OPTION 7 AND OPTION 8 - ELECTRONIC PARTLOW TEMPERATURE RECORDER OPTION -- 7 and OPTION 9 - NO TEMPERATURE RECORDER OPTION T-0PL

53 . OPTION 7 AND OPTION 8 - ELECTRONIC PARTLOW TEMPERATURE RECORDER Partlow Recorder Kit, Standard -- Includes: Recorder, Box & Door Assy s OPTION 7 (For field installation, units provisioned for - Refer to Manual T-00 ) Electronic Temperature Recorder Partlow Recorder Kit, Special -- Includes: Recorder, Box & Door Assy s OPTION 8 (For field installation, units provisioned for - Refer to Manual T-00 ) Electronic Temperature Recorder Door Assembly -- Includes: Seal, Door -- Rubber U-8-8 Screw, Retaining Panel Thickness -- SST Washer,. I.D. x.00 O.D. -- Mylar Washer, Retaining -- SST 7 9NT-0- Window 8 9NT-- Gasket Nut, Selflock, / Hinge Protector -- Mylar Screw, Hex Head, SEMS, #0- x / lg Screw, Hex Head, #0- x 7/ lg. -- SST SV Box Assembly -- Includes: Grommet, /8 ID x. OD Plug, Hole,.0 DIA 7 U--7 Washer, Flat, / -- SST 8 U-- Screw, Cap, Hex Head, /-0 x.7 lg. -- SST Washer, Retaining,.9 I.D. x.80 O.D. -- Mylar 0 9NT-9- Washer, Fender, / I.D. x O.D Washer, / I.D. x O.D. -- Mylar Washer,. I.D. x.9 O.D. -- Mylar Screw, Hex Head, SEMS, #0- x 7/ lg Stylus, Electronic Partlow Kit, Includes: NS -- Chart -- Owner Supplied A/R NS Charts _F -- Day (Box of 0) (--0_F to +80_F) A/R NS Charts _C -- Day (Box of 0) (--_C to +_C) A/R OPTION 9 - NO TEMPERATURE RECORDER Panel U--7 Washer, Flat, / -- SST 7 U-- Screw, Cap Hex Head, /-0 x.7 lg. -- SST 8 9NT-9- Washer, Fender, / I.D. x O.D Washer, Retaining,.9 I.D. x.80 O.D. -- Mylar Washer,. I.D. x.00 O.D. -- Mylar T-0PL

54 .7 COMPRESSOR MOUNTING COMPONENTS AND GUARD T-0PL

55 .7 COMPRESSOR MOUNTING COMPONENTS AND GUARD SV Compressor,Scroll -- Includes: (See Section ) Seal, Rotolock, - NS Seal, Rotolock, -/-- NS Compressor Oil O-Ring Shockmount, Bushing Shockmount, Ring Mount, Resilient, 80A Washer, Mylar --.0 X Washer,.87 X.0 X SST Protector, Mylar SV Base, Compressor (Painted) -- Includes: Protector, Mylar Bolt, Shoulder, /- UNC -- SST Bracket Assembly Bracket Assembly U--7 Bolt, Machine Hex Head, /-0 X. lg. -- SST U--7 Washer, Plain / -- SST Protector, Mylar Washer, Mylar.0 ID X.800 OD Nut, Self Lock /-0 -- SST Nut, Self Lock /8- -- SST U-- Washer, Plain /8 N Type A -- SST Washer, Mylar.7 ID X.00 OD Washer, Snubbing.7 ID X.00 OD Bolt, Shoulder, /8- UNC -- SST Screw, Cap Hex Head /-0 x.0 -- SST Cable, Power 7 U-- Screw, Hex Head, /-0 x / lg. -- SST Panel, Guard 9 U-- Capscrew, Hex Head, /-0 x -/ lg. -- SST Guard (Blue), Compressor Guard (White), Compressor U--8 Washer, Flat, #0 -- SST Washer, Mylar, 0.0 ID x 0.00 OD 7 U-7-7 Screw, Slotted Head, #0- x.0 lg. -- SST Partition Bracket 7 T-0PL

56 .8 TRANSDUCERS Option T - Transducer Locations T-0PL 8

57 .8 TRANSDUCERS OPTION T - PRESSURE TRANSDUCERS Switch, Pressure SV Transducer Kit -- Includes: Transducer, Suction NSS Cable, SPT Patch Transducer, Discharge EC9DM070 Core, Check Valve (Used with Tee) 9 T-0PL

58 .9 CABLE RESTRAINT COMPONENTS OPTION -- CABLE DOOR OPTION and - LEFT SIDE EXTENDED GUARD OPTION -- J-HOOK OPTION,, and - LEFT SIDE BUNGY CORD OPTION R -- DUMMY RECEPTACLE T-0PL 0

59 .9 CABLE RESTRAINT COMPONENTS OPTION - CABLE DOOR 9NT-7- Cover Assembly w/latch, Cable Storage -- Includes: Screw, Hex Head, #-0 x / lg. -- SST Washer, Flat, # --SST Locknut, Hex Head, # Washer, Mylar, /8 ID x /8 OD Latch 7 9NT-80 Hinge 8 U-0 Screw, Truss Head, #0- x / lg. -- SST 9 U--8 Washer, Flat, # Locknut, Hex Head, #0- -- SST Washer, Mylar, / ID x /8 OD Protector, Mylar Protector, Mylar Washer, Mylar, / ID x /8 OD Retainer, Nut U-0 Screw, Truss Head, #0- x / lg. -- SST 7 U--8 Washer, Flat, #0 -- SST 8 U-- Washer, Lock, #0 -- SST Latch, Catch OPTION - LEFT BUNGY CORD ONLY 0 9NT-99 Cable Restraint U--7 Washer, Flat, / -- SST U-- Screw, Cap, Hex, Head, /-0 x.7 lg -- SST Washer, Mylar,. I.D. X.00 O.D. U-0 Strap, Tie Down OPTION - J -HOOK 9NT-88 Cable Restraint, J-Hook Protector, Mylar 7 U--7 Washer, Flat, / -- SST 8 U-- Screw, Cap, Hex, Head, /-0 x.7 lg -- SST OPTION - LEFT BUNGY CORD WITH LEFT EXTENDED GUARD (UseOptionPlustheItemsBelow) Bracket, Left 0 U-0 Screw, Truss Head, #0- x / lg. -- SST A/R U--8 Washer, Flat, #0 -- SST A/R Washer, Mylar, / ID x /8 OD A/R OPTION R - DUMMY RECEPTICAL (for use in additon to Options -) Receptacle U--8 Washer, Flat, #0 SST U--7-- Screw, Cap, Hex, Head, 0-- x.7 lg -- SST T-0PL