SPARE PARTS LIST - VTA 6S - 400V 50Hz 3~ Version 2.1

Transcription

1 Valid from 23rd June 2014 Supersedes all previously issued spare parts lists Subject to change without prior notice.

2 10c 10a 10b (302188) a 10b 10c Base plate VTA6S outside coated structured (STATE COLOUR) Rubber foot with hexagon head screw M8x20 DIN 933, Perbunan Edge protective strip, black, 180mm Edge protective strip, black, 120mm Spring washer DIN127 A6 Hexagon nut DIN934 M6 8 gal Zn Rubber spacer VTA6S, 46x68x3, black Shore Foot VTA6S chromed (ABS) Cylinder head screw DIN84 M6x gal zn Mounting plate complete 400V/50Hz VTA6S with contactor and thermo-switch Thermo circuit breaker TI16C 4-6,2 A UL-approved Contactor AF (ABB) up to 400V Cover for contactor 2

3 Clamping ring (steel pipe) Stud bolt M6x40 DIN cylinder screw M4 x 10 DIN zn. Washer DIN125 A4,3 gal Zn Residue tray VTA6S with mesh 3

4 ,44 43,44 43,44 43,44 43,44 43,44 Hexagon nut DIN934 M6 8 gal Zn Clamp glued with insets Round handle, d=30x30mm, , M6, cross-hole Self-adhesive elastic buffer Dinstance bush VTA6S Rilsan black Stud screw M6x67 DIN (glued with grinder casing) Grinding disc carrier VTA6S chemically nickel plated, complete with sweeps Grinding disc set VTA6S steel coffee Grinding disc set VTA6ST steel coffee turkish fine, 9,4mm (from Serial No ) Grinding disc set VTA6ST steel coffee turkish fine, 11,0mm (until Serial No ) Grinding disc set VTA6SHM tungsten carbide Grinding disc set VTA6STHM tungsten carbide, turkish fine Grinding disc set VTA6S cast steel (coffee, spices, grains) 4

5 , Grinding disc set VTA6SW steel (only single-phase) Flat head screw DIN85 M5x10 A2-Niro stainless steel Screw for grinding disc carrier VTA6S chemical nickel plated Grinder casing cover VTA6S complete with grind adjustment Grind adjustment ring VTA6S complete Casing upper part for VTA 6S incl. lid, hopper, magnet in copper inside coating. Counter sunk head screw DIN963 M6x gal Zn Mains cable 4x1qmm Oelflex Quattro with CEE-plug 380V/16A 5pol. Screwed cable gland Skintop Pg 11 black, glued to (12) Bush 15x4x41 stainless steel Bush 15x4x12 stainless steel Seal ring polyester ( doughnut ) 5

6 Bag holder cap, ABS, black Bag holder switch (THS), complete VTA6S (without lever) (see p.12/13) Tappet, VTA6S, oil drenched, with insert nut Flat head screw M6x16 DIN 85 with Tuflok-spot Grinder casing VTA6S (CE & UL) Counter sunk head screw DIN963 M6x gal Zn Vibrating panel VTA6S polished Signal light SGF 21/3L-green 400 Volt 530mm Rubber funnel soft-pvc black Flat head screw M4 x 16 DIN85 #4.8 zn Flat head screw DIN85 M6x zn. Rubber tube piece, grinder casing VTA6S, D=8x15/30 Spring ring DIN127 A5 gal Zn 6

7 Cylinder head screw M5x20 DIN zn. Rubber cable joint (for manual lever VTA6S), S black, Ø25mm Lever THS-VTA6S stainless steel Handle THS 7

8 a a Spring washer DIN127 A6 Hexagon nut DIN934 M6 8 gal Zn Lower housing VTA6S outside coated - STATE COLOUR Lower housing VTA6S inside coated - STATE COLOUR Cover foil, brushed silver, self-adhesive, width 15mm, length 750mm Shock absorber, rubber-metal-buffer, Perbunan, oil-resistant, schwarz, 25x20 - M6x18 L-welding nut M6x8,5 DIN1624 Motor assembled VTA6S 400V/50Hz Bag holder switch cover, Polyester foam, 140x100x16, glued to (12) Lining for lower housing VTA6S - USA (Ul-approved) NOMEX-Aramid Grooved tapper pin 2x16 DIN1471 Pressure spring 1,0xDA14,5xL16,0mm 3 windings Washer DIN125 A8,4 gal Zn 8

9 a Spring washer DIN127 A4 gal Zn Hexagon nut DIN934 M4 gal Zn 9

10 Hopper magnet VTA6S complete with holder Seal ring polyester ( doughnut ) Hopper VTA6S complete glued Sheet metal raised counter sunk screw DIN7981 C4,2x19 H gal Zn Countersunk head screw DIN964 M3x8 4.8 zn Housing upper part VTA6S inside painted, copper (OTHER COLOURS ON REQUEST) Hinged lid VTA6S complete Makrolon brown transparent Cylinder head screw DIN84 M3x zn 10

11 Grind adjustment ring VTA6S Bolt for adjustment lever 11x35mm Adjustment lever complete Spring for adjustment lever d=1,25 x 12,5x5,00x3,00 Cylinder head screw DIN912 M6x blk. with full dog point Threaded pin DIN914-45H M4x8 Pressure piece VTA6S Notches cover foam black 360x30x22mm 11

12 Switch body THS pre-assembled Hexnut DIN439 M6 Gal Zn flat Spring ring DIN127 A6 Gal Zn Catch lever THS, compl. with bolt and roll Cylinder head screw DIN912 M6x VZ Catch bolt M6 THS VTA punched 12

13 Micro switch Cherry for THS, assembly group with washer and plate Counter sunk screw DIN 963-M4x8-4.8 verz Pressure spring 1,25xDA8,5xL31,0mm 12,5 windings Cover for bag holder switch Ball D=10 (steel) 3/8-Kl. 5 RB Slider plate THS compl.(stainless steel) Hexnut DIN439 M6 Gal Zn flat Spring ring DIN127 A6 Gal Zn Clamping plate THS rubber Cylinder head screw DIN84 M4x8 4.8 VZ Stop hook THS Ultramid black Guide ring THS black Spout tube THS black 13

14 Grinding disc carrier VTA6S nickel plated Counter sunk head screw DIN963 M3x5 4.8 A2 Sweep angle plate VTA6S 14

15 Changes In The Spare Parts List: VERS.NO. ARTICLE NO. DRAWING NO DESCRIPTION Single parts of bag holder switch are available seperately again COMMENT