over 100 are used all over India by our top customers many with repeat... repeat orders

Transcription

1 MFRS500SUS reliable & caring since 1976 All the 3 functions of Hot Air Reflow, Thru-Hole De & fine SMD Soldering, work independent ly at the same time No external ompressor required, needs Mains Supply only Push uttons for digitized temperature control 3 independent Heating hannels for: Hot Air Pencil Soldering Pencil De Pencil Push uttons for air volume control in-built Vacuum Pick-up lifts large SMD I gently without damage to SMD pads P Hot Air Pencil RS232 to US able for connection to US Port of external omputer L E A D RoHS ompliant F R E E Soldering Pencil De Pencil Software D Fine pitch SMD Soldering Thru-hole Soldering Large SMD I Reworking Thru-hole De Single System suffices for SMD, Thru-hole de & SMD Is reworking Scope of Supply: MFRS-500SUS Main ontrol Unit High Power Hot Air Pencil with in-built vacuum pick-up Hot Air Pencil Holder Soldering Pencil fitted with 2.4mm hisel Soldering Tip Support Rack with leaning Sponge and Dry leaner De Gun fitted with De Tip Support Rack with leaning Sponge for De Gun Power - Soldering/De - Hot Air Pencil Airflow Range Vacuum Suction : 1180 Watt : 200 ~ 480 : 100 ~ 500 : upto 120 litre/minute : 600mmHg Highly recommended option of Adjustable P Fixture & Hot Air Pencil Stand for effective and ease in reworking of large SMD Is Model AFHAPS parts as Heating Elements, Temperature Sensors, Soldering /De Tips, leaning Sponges etc. patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. ontents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements. Website: Phones: & ell: headoffice@indeonline.in

2 reliable & caring since 1976 MFRS500SUS OPTIONAL attachment AFHAPS Adjustable P Fixture & fine Up/Down Hot Air Pencil Holder is highly recommended to increase effectiveness of 3-in-1 SMD/PTH MFRS500SUS System The P Fixture retains and secures the P under repair and allows positioning of the board in X and Y directions. It permits Ps upto a maximum size of 350mm x 280mm both single and double sided to be accommodated in a perfectly flat condition. It also incorporates a pivoting stand to mount the Hot Air Pencil. This stand provides fine Up & Down movement of Hot Air Pencil for raising and lowering it onto the component under repair. The pre-heating plate IRPH-4 can be fitted under the P Fixture to provide gentle bottom heating. Features Hot Air Pencil Stand integrated with adjustable P Fixture is available optionally Maximum P size: 350 x 280 mm P can be positioned in X & Y directions Pre-Heating Plate can be positioned under the P It has 4 adjustable foot to adjust the level of P holder. oarse height range Fine height adjustment Maximum width of P : 0 ~ 230mm : 0 ~ 60mm : 280mm Adjustable P Holding Arms Holder for Hot Air Pencil UP/DOWN movement How to desolder large size expensive SMD Is on expensive multilayer Printed ircuit oards? q hoose an appropriate hot air nozzle and fix the P on P Fixture and position the SMD I exactly under the Hot Air Pencil. q Adjust airflow and temperature between 400 ~ 500 depending upon the size of SMD I. Adjustable Foots for level adjustment q Adjust the temperature of bottom pre-heater so that the temperature on the top side of P reaches around 120. heck the temperature on the component using Thermocouple supplied with Pre-heat plate. q Switch-on the hot air and blow hot air from small distance to pre-heat the SMD I to avoid any thermal shock to it. q Lower the Hot Air Pencil on SMD I and wait for solder to melt. q Once the solder melts, switch-on the vacuum and lift the Hot Air Pencil, SMD I will be lifted safely by Hot Air N ozzle due to its vacuum pick-up. parts as Heating Elements, Temperature Sensors, Soldering /De Tips, leaning Sponges etc. patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. ontents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements. Website: Phones: & ell: headoffice@indeonline.in

3 MFRS500SUS reliable & caring since 1976 OPTIONAL Programmable Hi-Power infrared Pre-heating Plate 600 Watt Model IRPH-4 necessary for high heat sink and multilayer Printed ircuit oards reworking & repair The IRPH-4 Pre-heating Plate enhances the effectiveness of the MFRS500SUS systems. It provides bottom heating to the P under repair, therefore minimizing the risk of thermal damage to expensive SMD Is and warping of expensive multilayer Ps. Additionally it also speeds up the rework/repair process. Display for SET and ATUAL temperatures Heating Area 130x130mm Display for external Thermocouple temperature Port to plug-in external Thermocouple Precise temperature control with digitized Push uttons Features: High quality, long life IR eramic Heating Elements ensure fast and even pre-heating with high efficiency in-built temperature measurement with thermocouple allows continuous monitoring of P temperature Pre-set temperature is achieved accurately and remains stable due to closed loop PID control design. : Heating Power Plate Area Heating Source : 600 Watt : 130 x 130mm : IR eramic Heater Temperature Sensor Measurement Range : K-type Thermocouple : 50 ~ 350 : 0 ~ 600 Why bottom Preheating is recommended? Today s electronics design has higher density of expensive devices on the multilayer Ps which inherently require gentle pre-heating of Ps to avoid thermal damaging of expensive SMD Is, and also must avoid warping of Ps. If pre-heating is not used, it can lead to pad lifting, delamination, warping and burning of expensive Ps & large SMD Is during rework/repair. eside these visible defects, the invisible defects like internal layer cracking etc. will also result if pre-heating is not used. To avoid above failures, Ps will normally need even pre-heating around 120 on top side while reworking. The Pre-heater model IRPH-4 serves this purpose. Ps are heated evenly and gently from bottom side for safe reworking of SMD Is. P warping/burning possibility without pre-heating Safe reworking of SMD Is using bottom Preheater parts as Heating Elements, Temperature Sensors, Soldering /De Tips, leaning Sponges etc. patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. ontents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements. Website: Phones: & ell: headoffice@indeonline.in

4 reliable & caring since 1976 MFRS500SUS 1000 Watt high heat power and very powerful upto 120 litre/minute Hot Air Pencil also has in-built Vacuum Pick-up provision for safe de of large SMD Is. Gentle lifting by Vacuum Pick-up does not damage SMD Pads of expensive Ps. The ergonomic and powerful Hot Air Pencil (1000 Watt) together with the extensive range of Hot Air Nozzles make this tool very versatile. Hot Air Nozzles are secured to the tool by press fitting. It has integrated in-built powerful vacuum pick-up for gentle lifting of large SMD Is during de without any damage to SMD pads of expensive Ps. Temperature controlled Hot Air Pencil provides adjustable high volume of airflow. Different Hot Air Nozzles are available for different shapes and sizes of SMD Is. in-built Vacuum Pick-up lifts large SMD Is gently during reworking/ repairing without any damage to SMD Pads on P of Hot Air Pencil Power: 1000 Watt : 100 ~ 500 Airflow Volume: upto 120 litre/minute Wide range of Hot Air Nozzles available to desolder/solder miniature chip components and even as large as 50 x 50 mm size Fine-Pitch SMD Is like: QFPs, PLs, TSOPs Large PLs like PL 84 L leadless hip arrier Flat Packs Large QFPs as 208 & 304 Pins eramic Quad Flat Packs Thin SOP Is NK mm dia SMD hips NK3131 Size: 4x10mm SOP 4.4x10 NK3128 Size: 15x21mm QFP 14x20 NK3136 Size: 19x19mm PL 20x20 NK3137 Size: 24x24mm PL 25x25 NK3264 Size: 39x39mm QFP 40x40 Other size Hot Air Nozzles are also available as per customer s requirement, please tell size of SMD I. parts as Heating Elements, Temperature Sensors, Soldering /De Tips, leaning Sponges etc. patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. ontents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements. Website: Phones: & ell: headoffice@indeonline.in

5 MFRS500SUS reliable & caring since 1976 Unique design of Soldering Pencil for SMD and PTH The Soldering Pencil uses unbreakable heating element in coiled form encased in metal tube with sensor placed very close to the tip for precise control of temperature. Push-fit design allows quick and easy change of Soldering Tips. Heating Power Tip to ground Potential Tip to ground Resistance : 90 Watt : 100 ~ 500 : <2mV : <2Ω Fine pitch SMD Soldering Thru-hole Soldering Unique SMD Soldering Tip for fine pitch SMD Is without bridging Specially designed 200G-M SMD Soldering Tip has concave cavity to hold the molten solder. It helps to solder one side of I completely in a single go by dragging the tip on the P tracks slowly without any bridging. Easy-to-hold De Pencil for De Thru-Hole omponents De Pencil, with internal solder reservoir, desolders thru-hole components. Finger Switch controls quick start of fast action vacuum pump. Heating Power Vacuum Pressure Tip to ground Potential Tip to ground Resistance : 90 Watt : 200 ~ 480 : 600mmHg : <2mV : <2Ω De Nozzles available to desolder different PTH components P/N A1005 A1006 A parts as Heating Elements, Temperature Sensors, Soldering /De Tips, leaning Sponges etc. patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. ontents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements. Website: Phones: & ell: headoffice@indeonline.in

6 reliable & caring since 1976 MFRS500SUS Wide range of Soldering Tips are available for different applications Description Actual Picture Dimensional Diagram Width A (mm) Part Number hisel Tip G-0.8D hisel Tip G-1.2D hisel Tip G-1.6D hisel Tip G-2.4D hisel Tip G-3.2D hisel Tip for heavy mass G-4.2D Long hisel Tip for heavy mass G-5LD Sloped Tip for Solar Panels Ø3 200G-3 Sloped Tip for Solar Panels Ø4 200G-4 Sloped Tip for Solar Panels Ø5 200G-5 Round Tip for Fine Soldering 17 Ø G- Tip for SMD Soldering G-2M parts as Heating Elements, Temperature Sensors, Soldering /De Tips, leaning Sponges etc. patents. We accept no liability of whatsoever for any faults and errors in the information contained herein. ontents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements. Website: Phones: & ell: headoffice@indeonline.in