UNO BOOSTER BASIC DUO BOOSTER BASIC

Transcription

1 UNO BOOSTER BASIC DUO BOOSTER BASIC Instruction manual Betriebsanleitung Manuel d Instructions Gebruikershandleiding Manual de instrucciones Manuale di istruzioni Руководство

2 Index Safety Precautions and Warnings Description 2. Application Operation elements Installation 3. Temperature conditions Condition of distance Wall mounting Water connection Mains power connection High pressure connection Venting Operation 4. Connections High pressure hose - directly on the machine High pressure hose - to outlet point Spray handle - accessories Selection of spray lance Application of detergents (external injector) Application of detergents (internal) Starting up Operation - automatic start/stop Double spray lance, pressure regulation Stop Frost protection Fields of Application and Working Methods 5. Fields of application Working pressure Detergents Working methods Maintenance 6. Oil Water fi lter Cleaning of high pressure nozzle Disposable waste Trouble Shooting Technical Data Warranty...25 EC Declaration of Conformity

3 Safety Precautions and Warnings Before starting up your high pressure washer for the fi rst time, this instruction manual must be read through carefully. Save the instructions for later use. Only let instructed people operate the machine. General When using the high pressure washer all existing national regulations must be observed. Beyond the instruction manual and the current national legal regulations for prevention of accidents, also the approved rules for safe working must be observed. Any method of use endangering the safety of persons or equipment is forbidden. Before use Before starting up your high pressure washer check that it is in a regular condition. Electric plugs and couplings must be watertight. Check the electric cables at regular intervals for damage and wear. Only use the high pressure washer if the electric cable is all right (damaged electric cables can cause electric shock!) Important instructions Connection to public mains according to the applicable regulations in your country. IMPORTANT: Only use water without impurities! Before each use of your high pressure washer check the most important visual parts. High pressure jets can be dangerous if misused. Never direct the water jet towards people, pets, electric wiring, or the machine itself. Spray handle and lance are affected by a thrust during operation - therefore always hold the spray lance fi rmly with both hands. Never try to clean clothes or footwear on yourself or other persons. Operator and anyone in immediate vicinity of the site of cleaning should take action to protect himself from being struck by debris dislodged during operation. Check that cleaning will not result in dangerous substances (e.g. asbestos, oil) being washed off the object to be cleaned and harming the environment. Do not clean sensitive surfaces made of rubber, fabrics or the like with the zero nozzle. With the fl at jet nozzle keep a distance of at least 5 cm to the surface to be cleaned. Never let children operate the machine. Do not use the machine if the electric cable or the high pressure hose are damaged. Do not cover the machine during operation or use it in a room without adequate ventilation! If the overload protection device of the motor trips (motor stops), release the trigger of the spray handle. Lock the spray handle with locking device and turn the start/stop switch to position 0. Let the machine cool off for at least 3 minutes! The machine must be placed in a room where it is not exposed to frost. Never start the cleaner without water supply. Even a short water defi ciency can damage the sleeves of the pump. Operation Avoid damage to the electric cables such as running over by a car, squeezing, pull, knots etc. and keep them away from sharp or hot objects. Avoid damage to the high pressure hose such as running over by a car, squeezing, pull, knots/kinks etc. and keep it away from oil and sharp or hot objects, as such may cause the hose to burst. The cleaner can be used in zones classifi ed as ZONE 2. 4

4 Important! Never use the machine in an environment where there could be a danger of explosion (according to EN- 5004). Important! When the system has been in operation and thereafter stopped, there will still be a working pressure in the pipeline and high pressure hoses. Therefore you should pay special attention to the following: Never dismount the high pressure hose from the machine during operation. Disconnect the machine, close the shut-off cock and relieve the high pressure hose of pressure prior to dismounting. Never dismount the high pressure hose from the outlet point before it has been securely closed and the high pressure hose has been relieved of pressure. Prior to any service interference in the machine it should be disconnected and the system relieved of pressure by activating the trigger of the spray handle. Repair and Maintenance Only carry through the maintenance operations described in the operating instructions. Only use original Nilfi sk-alto spare parts. Do NOT make any technical modifi cations to the high pressure washer. Warning! High pressure hoses, nozzles and couplings are important for the safety when operating the machine. Only use the high pressure hoses, nozzles and couplings prescribed by Nilfi sk-alto! For major repairs, please contact your nearest Nilfi sk- ALTO service organisation. Mains power connection Check the nominal voltage of the high pressure washer before connecting it to the electricity supply. Check that the voltage stated on the model tag corresponds to your mains voltage. A circuit breaker must be placed in the immediate vicinity of the machine. We recommend you to connect the machine to a power source with a Residual Current Device (RCD) which will disconnect the power supply if the leakage current exceeds 30 ma for 20 milli seconds. Only connect to an approved socket with earth connection. Only connect the machine to an electrical installation made by an qualifi ed electrician. The insulation of the electric cable should be quite faultless and without any cracks. If you are in doubt about the the mains power connection, please contact a qualifi ed electrician. Note: If using another cable it must be earthed and connected through the plug to the earth cable of your supply network in accordance with prescribed safety regulations. Always use a cable similar to the one mounted on the machine. Check cables before usage. Do not use damaged cables. Only let a qualifi ed electrician replace the electric cable. Safety Devices Safety Valve The pressure side of the high pressure pump is fi tted with a safety valve. This valve leads the water back to the suction side of the pump when the spray handle is closed or if a nozzle is blocked. The safety valve is adjusted and sealed by the producer. THIS ADJUSTMENT MUST NOT BE CHANGED! Motor protection The motor features an overcurrent protection and built-in thermal switches for protection of motor against overloading. In the event of increased power consumption (maloperation), the current for the motor will automatically be cut out. 5

5 2 Description 2. Application This high pressure washer has been developed for professional use within: - agriculture - light industry - transport - building and construction - service Only use the high pressure washer for purposes described in this manual. The safety precautions must be observed to prevent damage to the machine, the surface to be cleaned or severe personal injuries. Section 4 describes how to use the high pressure washer. 2. Operation elements Water connection with fi lter 2 Main switch 3 Starter switch 4 Stop switch 5 Pressure gauge 6 Connection of high pressure hose 7 Electric cable 6

6 0 0 3 Installation 3. Temperature conditions The machine should be installed in a frost-free room. This applies to pump as well as pipelines incl. of outlet points. Con cern ing outdoor outlet points it should be possible to close and emp ty that part of the line which is exposed to frost. The maximum ambient temperature for the machine is 40 C. 3.2 Condition of distance Min 400 mm Min. 50 mm Min. 50 mm In consideration of the cooling system of the machine and the accessibility of service, there must be free wall space on both sides of the machine. To the right 50 mm at a min i mum and to the left 400 mm at a min i mum. Min 400 mm UNO BOOSTER: The recommended installation height for the machine is max. 700 mm measured from the upper edge of the machine. Max. 700 mm 7

7 3.3 Wall mounting UNO BOOSTER: Only mount the machine on a solid wall construction suited for the mounting of a ma chine. I.e. a concrete or brick wall. Do not mount the machine on a wall where it will cause disturbances in neighbouring rooms (canteens, offi ces etc.). DUO BOOSTER: Place the machine on a plane fl oor. Machine feet have been mounted under the machine. These must be adjusted so that the machine stands stable. 3.4 Water connection The water connection is made through a fl exible hose connected to the quick cou pling on the water inlet () of the machine. The connection can be made to a water supply network or an internal water sup ply. A shutoff cock should be mounted on the water supply network in the immediate vicini ty of the ma chine. Max. water pressure: 0 bar Max. water inlet temp.: 70 C The machine features a water tank, and no further protection against return water into the supply network is required. The machine complies with EN 77. If there is a risk of running sands or other impurities in the inlet water, a sand fi lter (50 micron) should be mounted beyond the internal fi lter of the machine (for further connection data see section 8 Tech ni cal data). If mounting the by-pass hose, the water inlet temperature can be raised to 80 C. ONLY do this if there is a separate water supply (contact your Nilfi sk- ALTO distributor). Clean the water inlet fi lter () once a month. 8

8 3.5 Mains power connection Connect the machine to an approved socket. Check voltage, fuse, and cables according to section Safety proceautions and warnings. Connection data conc. power consumption can be taken from the model tag of the machine. 3.6 High pressure connection MPORTANT: When connecting to a pipeline always use a fl exible hose connection from the outlet of the machine (pos. 7) - order no Contact your Nilfi sk-alto distributor for further information. The outlet of the machine can be connected to a pipeline with fi xed outlet points, or standard high pres sure hoses can be connected directly to the outlet of the machine. It is recommended to let a service tech ni cian authorized by Nilfi sk-alto prepare the pipeline. 9

9 3.7 Venting UNO BOOSTER: 0 Turn start/stop switchto position - -. Open the outlet point. Let the water run until all air has escaped from the pump (even water fl ow). In the case of a recently installed sys tem, or if the pipeline and the pump have been emptied in any other way, the system should be vented by starting the pump and then let the water run at each outlet point of the pipeline at turns. When con nect ing the high pressure hose directly to the ma chine, the sys tem should be vented by starting the pump and ac ti vat ing the trigger of the spray handle without having attached the spray lance DUO BOOSTER: In the case of a recently installed sys tem, or if the pipeline and the pump have been emptied in any other way, the system should be vented as follows:. At fi rst start pump no. and let the water run from an outlet point of the pipeline. When con nect ing the high pressure hose directly to the ma chine, activate the trigger of the spray handle without having attached the spray lance. Let the water run until all air has escaped from the pump (even water fl ow). 0

10 3.7 Venting (continued) Stop pump no.. Then start pump no. 2 and let the water run from an outlet point of the pipeline. 0 When con nect ing the high pressure hose directly to the ma chine, activate the trigger of the spray handle without having attached the spray lance. Let the water run until all air has escaped from the pump (even water fl ow). 3. Vent the pipeline by starting one pump and then let the water run at each outlet point of the pipeline at turns until all air has escaped from the system.

11 4 Operation 4. Connections 4.. High pressure hose - directly on the machine a 6 The Nilfi sk-alto high pressure hose with imprinted max. working pressure and temperature should be attached to the outlet connection of the machine (6) by the quick coupling (a). Max.extension hose: 50 m. Danger of scalding! Never dismount high pressure hoses at water temperatures above 50 C. IMPORTANT: Prior to dismounting of the high pressure hose the machine should be stopped and the shut-off cock closed. Then activate the trigger of the spray handle to relieve the high pres sure hose of pressure High pressure hose - to outlet point 3 2 In the case of a pipeline with fi xed outlet points the high pressure hose with imprinted working pressure and temperature should be attached to the nipple of the high pres sure cock () by the quick coupling (2). Upon attachment turn the handle of the high pressure cock (3) to open position. Danger of scalding! Never dismount high pressure hoses at water temperatures above 50 C. IMPORTANT: Prior to dismounting of the high pressure hose or when changing to another outlet point the high pressure cock should be care ful ly closed. Then activate the trigger of the spray handle to relieve the high pressure hose of pressure. 2

12 4..2 High pressure hose - to outlet point (continued) Pipeline, max. length: UNO BOOSTER Ø2 x,5 - max. 50 m Ø5 x,5 - max. 80 m Ø8 x,5 - max. 500 m DUO BOOSTER Ø5 x,5 - max. 25 m Ø8 x,5 - max. 20 m Ø22 x 2,0 - max. 250 m When using max. pipe lengths, only use a high pressure hose of 0 m Spray handle - accessories 2. Pull forward the quick coupling trigger () of the spray handle. 2. Insert the nipple of the spray lance (2) in the quick coupling and release the trigger. 3. Pull forward the spray lance or any other accessory to ensure correct mounting before starting the machine. NOTE! Clean nipple of any impurities each time the spray lance has been dismounted Selection of spray lance MULTIPRESSURE P bar Q l/min. C N 27 7 Hvid Sort Brun Grøn Blå Rød Orange Gul Blank You may use a double spray lance as well as a single spray lance with the ma chine. The ma chine has been optimized to use spray lances with a type 06 nozzle. The max. pres sure of the machine can be reduced by using noz zles with a wider di am e ter. See diagram. P: Nozzle pressure Q: Water volume C: Colour code N: No. of pumps (2 only DUO) 3

13 4..5 Application of detergents (external) If you want to apply detergents or disinfectants these should be dosed to the water through an injector. In conjunction with the injector it may be ad van ta geous to use a wall rack on which spray lances, 2 pcs. of 25 l containers as well as 0 m high pressure hose can be placed. Below you will fi nd various types of outlet points with injectors. Outlet point with detachable injector To be attached to the quick coupling of the high pressure cock. To be used for dosing of low-foaming detergents or disinfectants. Dosage -8%. Outlet point with detachable foam injector To be attached to the quick coupling of the high pressure cock. To be used in conjunction with foam lance for application of high-foaming de ter gents or disinfectants. Dosage -5%. Outlet point with cleaning trolley and foam injector To be attached to the quick coupling of the high pressure cock. To be used in the same way as Outlet point with detachable foam injector. Makes it possible to place 4 spray lances, 2 pcs. of 25 l containers as well as 20 m high pressure hose. 4

14 Application of detergents (internal) 2 This kind of detergent addition is an option. A Insert the suction hose () from the machine in the container. On the regulating knob (2) the dosage can be set from -4%. If the machine is mounted on a pipeline, detergent will come out of all outlet points. The ph value MUST be between 5.5 and Starting up The shut-off cock on the water inlet should be open. UNO BOOSTER:. Turn the main switch (2) to position Push the green starter button (3). 0 Check on the pressure gauge (5) that a pressure is being built up in the system. If a pressure is not being built up, vent the machine as de scribed in section 3.7 Venting. DUO BOOSTER: Position = Pump no. in operation Position 2 = Pump no. 2 in operation Positions +2 = Pumps no. and 2 in operation Turn the main switch (2) to position, 2 or Push the green starter button (3). Check on the pressure gauge (5) that a pressure is being built up in the system. If a pressure is not being built up, vent the machine as de scribed in section 3.7 Venting. 5

15 4.3 Operation - automatic start/stop Always hold the spray lance with both hands! The machine is automatically activated when the trigger () of the spray handle is activated. When the trigger is released, the machine automatically stops after 20 seconds. When the machine is not in use, the trigger should be locked with locking device (see arrow). 4.4 Double spray lance, pressure regulation The spray lance features 2 nozzles, a high pressure nozzle and a low pressure nozz le. High pressure mode When the pressure reducing valve () is completely closed (turned clockwise - B), only the high pressure nozzle is used - high pressure mode. Low pressure mode When the reducing valve () is completely opened (turned counterclockwise - A), both spray lances are used - low pressure mode / possibility of dosing detergents. The pres sure may be reg u lat ed between these positions. 6

16 4.5 Stop Danger of scalding! Never detach high pressure hoses at a water temperature above 50 C. 0 Never detach the high pressue hose while the machine is in operation.. To stop the machine turn the main switch (2) to position Close the shut-off cock of the water inlet and activate the spray lance or open the high pressure cock to relieve the pipeline / high pressure hose of pressure. 4.6 Frost protection The machine should be installed in a frost-free room. This applies to pump as well as pipelines incl. of outlet points. Concerning outdoor outlet points it should be possible to empty that part of the line which is exposed to frost. IMPORTANT: For safety reasons, hoses, spray lances and other accessories should always be thawed prior to use. 7

17 5 Fields of Application and Working Methods 5. Fields of application The most important fi elds of application for this product are: Agriculture Transport Building & Construction Light industry Service Cleaning of machinery, agricultural implements, stalls, equipment and buildings. Cleaning of trucks, buses, cars etc. Cleaning of vehicles, equipment, buildings etc. Degreasing and cleaning of machines, workpieces, and vehicles. Cleaning of vehicles, public baths, institutions etc. 5.2 Working pressure The high pressure system may be used with high or low pressure at your own option: Low pressure High pressure Intermediate pressure Is fi rst and foremost used for the application of detergents and for rinsing. Is used during the actual cleaning. As an example it may be used for the cleaning of surfaces which cannnot stand a too powerful jet, i.e. soft surfaces. 5.3 Detergents As standard the system is delivered without a detergent injector. If you want to use detergents or disinfectants these should be dosed through an external injector (see section 4..5) or internally through the pump (see section 4..6). The most effi cient cleaning is reached with detergents in conjunction with the high pressure cleaning. For that purpose Nilfi sk-alto can offer you a series of products specially developed for high pressure cleaning, among other fi elds within: Cleaning of vehicles, machines, stalls etc. Disinfection Degreasing of workpieces Descaling The products are water-based, without phosphates, and the applied tensides (surface active substances) comply with the present requirements for easy biodegradability. Contact your Nilfi sk-alto distributor for directions as to which product(s) will fulfi l your requirements. The method of application and the dosage of the individual products appear from the product labels or the data sheet. Low-foaming detergents are applied through an injector and under low pressure. A change to cleaning under high pressure is effected by regulating from»low pressure mode«to»high pressure mode«on the double spray lance or by attaching a high pressure spray lance. 8

18 5.3 Detergents (continued) For foam cleaning you will have to attach a special foam equipment. Insert the suction hose of the injector into the foam detergent. Attach the foam lance on the spray handle and now you are ready for foam application. Upon the application open the by-pass cock of the foam injector and replace the foam lance by a spray lance, and you are ready for cleaning. General rules for addition of detergents Nilfi sk-alto cleaning equipment can be used for all detergents and disinfectants, which are suitable for high pres sure cleaning according to the prescriptions of the supplier. (If using external injector, the ph-value should be between 4 and 4. If using internal addition of chemicals, the ph-value MUST be between 5.5 and 8.5). Acid and lye should not be applied in a concentrated form. Carefully observe the prescriptions and guidelines of the supplier, also the rules concerning safety clothing and drainage facilities. Detergents which are not exactly prescribed for use in conjunction with high pressure cleaning must only be used upon a previous approbation from Nilfi sk-alto and the supplier. The use of Nilfi sk-alto detergents ensures that machines, accessories and detergents match, which is the con di tion of an optimal solution of a cleaning task. Nilfi sk-alto can offer you a wide range of effi cient agents for cleaning and disinfection. The products are composed of substances which combine effi ciency and environmental considerations at one and the same time. 9

19 5.4 Working methods Your high pressure washer has been developed for cleaning according to the so-called»2-step method«. However, your high pressure washer must be equipped with an external detergent injector. STEP Application of detergent STEP 2 High pressure cleaning In practice the working process is laid down in accordance with the actual job, but as a starting point the following working method can be described for a job:. Apply detergent under low pressure. The dosage is chosen according to the job which is to be carried through, and the adjustment is made on the dosing unit. 2. Await acting time. Let the detergent act on the dirt/ surface for a short time prior to pressure cleaning - usually a few minutes. 3. High pressure cleaning. Clean all surfaces under high pressure. 4. Rinse afterwards, if necessary. To make sure that residual impurities are removed from the surface. In connection with the working process the optimum cleaning will be reached by following these 3 pieces of advice: Advice no. When using a detergent, usually always apply it on a dry surface. If the surface is rinsed with water at fi rst, it may be diffi cult for it to absorb the detergent, and the result is a reduced effect of the detergent. Advice no. 2 When applying a detergent on large vertical surfaces (i.e. the sides of a truck) work from below and upwards. Thus you will avoid the detergent running off the surface through grooves and dark streaks appearing on the surface whilst cleaning. Advice no. 3 During the high pressure cleaning you should work so that the high pressure water does not run over the surface which has not been cleaned yet. This is to ensure that there is suffi cient detergent on the surface when the high pressure water hits the surface. 20

20 6 Maintenance It applies to the most exposed components that a minimum of maintenance ensures a prolonged and prob lem-free operation. Therefore it will be a good idea to make a habit of the following: Prior to attaching the water hose and the high pressure hose, the quick couplings should be cleaned of dust and sand. Prior to attaching the spray lance or other accessories to the spray handle, the machine should be started and the quick coupling cleaned of dust and sand. 6. Oil Check the oil level in the oil glas. If the oil level gets too low, the machine will automatically shut down. PROTECT THE ENVIRONMENT Waste oil and oil sludge must be removed as laid down in the instructions. In the case of repeated low oil level (oil waste) please contact a Nilfi sk-alto service technician. 6.2 Water filter To avoid debris entering the high pressure pump, a water fi lter (fi ne) is fi tted at the wa ter inlet. Dependent on the purity of the water, this fi l ter will have to be cleaned at regular in ter vals. The fi lter can be removed when the quick coupling (pos. ) has been un screwed. UNO BOOSTER DUO BOOSTER The water tank also features a fi lter (coarse) (2 pcs. in DUO BOOSTER) ensuring that fl akes of scale are not en ter ing the pump. The fi lter should be cleaned at regular intervals. The two fi lters must not be interchanged, as their fi ltration capabilities differ. 2

21 6.3 Cleaning of high pressure nozzle A clogging up in the nozzle causes a pump pressure which is too high, and a cleaning is immediately required.. Stop the cleaner and detach the spray lance. 2. Clean the nozzle. IMPORTANT: ONLY use the cleaning tool when the spray lance is detached. 3. Flush the spray lance backwards with water. 4. If the pressure is still too high, repeat items Disposable waste This high pressure washer consists of parts which can affect the invironment when thrown away. Parts that can pollute are as follows: Oil, painted/zinc-coated parts, plastics/plastic-coated parts. Therefore, it is important to follow the laws concerning the removal of polluting and dangerous materials when replacing spare parts or disposing of high pressure washer. It is recommended that you bring the rejected parts to waste disposal areas or recycling plants that are approved for the destruction of these types of materials. 22

22 7 Trouble Shooting You have chosen the best quality and therefore deserve the best service. To avoid unnecessary dis ap point ments, you should check the following before contacting the nearest Nilfi sk-alto service organisation: Symptom Reason Action Machine will not start > A fuse has blown Change the fuse. > Power/plug not connected Connect power/plug. > Thermal switches in motor Let the motor cool. Start activated the machine and check that the working pressure is > Thermal relay switched off not too high and that the (red lamp is on) mains voltage corresponds to the specifi cations. > Oil shortage in pump Refi ll with oil. DUO BOOSTER: > Water temperature too high Lower the temperature of the inlet water to max. 70 C. Bypass 80 C. Fuses blow > Installation does not Change to an installation. correspond to the ampere corresponding to the ampere consumption of the machine consumption of the machine at a minimum. Change the fuse. Working pressure too low > Nozzle worn Replace the nozzle. > Wrong spray lance Replace the spray lance (see section 4.4). > Reduction valve of spray Turn reduction valve comlance not adjusted to max. pletely counter-clockwise pressure. (see section 4.4). > Nozzle partly clogged up Clean the nozzle (see section 6.3). Working pressure fluctuating > Water temperature too high Lower the temperature of the inlet water to max. 70 C. Bypass 80 C. > Insuffi cient water supply Dismount the cabinet and check that the water tank is not drained of water during operation of the machine. If it is, clean the water inlet fi lter of the machine. If that does 23

23 Symptom Reason Action Working pressure fluctuating (continued) not solve the problem, the water supply for the machine is insuffi cient. NB! Avoid long, thin hoses (min. 3/4"). > High pressure hoses too long Dismount high pressure extension hoses and retry. Extension hose max. 50 m. NB! Avoid long extension hoses with many couplings. > Air in the system Vent the system (see section 3.7). > Water inlet fi lter clogged up Clean filter (see sect. 6.2). No working pressure > Nozzle clogged up Clean nozzle (see sect. 6.3). > No inlet water Check that the shut off cock of the water inlet is open. Check that the water supply meets the requirements (see section.2). > High pressure cock of outlet Close all high pressure point open. cocks not in use. Machine starts and > Leaky hose/ Repair leak. stops pipeline/spray handle Machine starts > Oil shortage in pump Refi ll with oil. Should other malfunctions occur than those mentioned above, please contact your nearest Nilfi sk- ALTO service organisation. 24

24 8 Technical Data Model UNO BOOSTER DUO BOOSTER Pump pressure ) bar Water volume, min./max. pressure l/min 9./ / Water tank, volume liter Water connection: Max. pressure, inlet water bar 0 0 Min. pressure, inlet water bar,0,5 Max. temperature, inlet water C 70 (80, see section 3.4) 70 (80, see section 3.4) Spray lance: Nozzle type, h.p./l.p Thrust, max. N/kp 47/4,8 47/4,8 Pipeline, max. length m Ø2 x,5 - max. 50 Ø5 x,5 - max. 25 m Ø5 x,5 - max. 80 Ø8 x,5 - max. 20 m Ø8 x,5 - max. 500 Ø22 x 2,0 - max. 250 When using max. pipe lengths, only use a high pressure hose of 0 m. ) When using a 0 m (3/8") high pressure hose. Sound pressure level L pa measured in accordance with ISO 202 [DISTANCE m] [FULL LOAD]: 79 db(a). Data stated at 2 C hot inlet water. We reserve the right to make alterations. 9 Warranty Your Nilfi sk-alto product is guaranteed for 2 months from date of purchase (purchase receipt must be presented) on the following conditions: that defects are attributable to fl aws or defects in materials or workmanship. (Usual wear and tear as well as misuse are not covered by the guarantee). that repairs have not been carried out or attempted by other than Nilfi sk-altotrained service staff. that only original accessories have been applied. that the product has not been exposed to abuse such as knocks, bumps or frost. that the instructions in the manual have been carefully observed. A warranty repair comprises the replacement of defective parts, but it does not cover freight and packaging charges. Besides we refer to national Sale of Goods Act. Any illegitimate guarantee repair will be invoiced. (I.e. malfunctions due to causes mentioned in section 7.0 Trouble shooting of the instruction manual). 25

25 EC Declaration of Conformity EG-Konformitätserklärung The undersigned, representing the following manufacturer, Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund declares that the product: High Pressure Washer type : UNO BOOSTER / DUO BOOSTER is in conformity with the provisions of the following EC directives, with subsequent amendments: 98/37/EEC, 73/23/EEC, 85/374/EEC, 89/366/EEC and furthermore declares that the following harmonised standards have been applied: EN , EN 292, EN 294, EN 349, EN 457, EN 563, pren 77 EN 5504, EEN , EN , EN , pren The following (parts/clauses of) national technical standards and spec i fi ca tions have been used: IEC Der Unterzeichnete, der den folgenden Hersteller vertritt: Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund erklärt hiermit, daß das produkt: Hochdruckreiniger Typ : UNO BOOSTER / DUO BOOSTER konform ist mit den Bestimmungen der folgenden EG-Richtlinien, inklusive deren Änderungen: 98/37/EEC, 73/23/EEC, 85/374/EEC, 89/366/EEC Desweiteren erklären wir, daß die folgenden harmonisierten Normen (oder Teile/Klauseln hieraus) zur Anwendung gelangten: EN , EN 292, EN 294, EN 349, EN 457, EN 563, pren 77 EN 5504, EEN , EN , EN , pren und daß folgende nationale technische Normen und Spezifi ktionen zur Anwendung gelangten: IEC Hadsund, February 2002 Anton Sørensen V.P. Technical Operations Europe Hadsund, den. Februar 2002 Anton Sørensen V.P. Technical Operations EuropE Déclaration de Conformité EC Le fabricant soussigné, Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund déclare que le produit : Nettoyeur haute pression type : UNO BOOSTER / DUO BOOSTER est conforme aux dispositions des directives CE suivantes, et aux amendements ultérieurs : 98/37/EEC, 73/23/EEC, 85/374/EEC, 89/366/EEC et déclare également que les critères harmonisés ci-après ont été appliqués : EN , EN 292, EN 294, EN 349, EN 457, EN 563, pren 77 EN 5504, EEN , EN , EN , pren Les critères techniques et spécifi cations nationales ci-après ont été utilisés (parties/clauses) : IEC Verklaring van conformering aan EG-regelgeving Ondergetekende, functionerend als vertegenwoordiger van de fabrikant Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund verklaart dat het product: Hogedrukreiniger type: UNO BOOSTER / DUO BOOSTER voldoet aan de eisen gesteld in de volgende EG-regels, met daaropvolgende wijzigingen: 98/37/EEC, 73/23/EEC, 85/374/EEC, 89/366/EEC en verklaart bovendien dat de volgende geharmoniseerde standaarden zijn gehanteerd: EN , EN 292, EN 294, EN 349, EN 457, EN 563, pren 77 EN 5504, EEN , EN , EN , pren De volgende (delen/artikelen van) nationale technische standaarden en specifi caties zijn gebruikt: IEC Hadsund, le er février 2002 Anton Sørensen V.P. Technical Operations Europe Hadsund, februari 2002 Anton Sørensen V.P. Technical Operations Europe Declaración de conformidad de la CE Dichiarazione di conformità CE El abajo fi rmante, en representación del fabricante Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund declara que el producto: Hidrolimpiadora de alta presión tipo: UNO BOOSTER / DUO BOOSTER es conforme con las disposiciones de las siguientes directivas de la CE con sus consiguientes enmiendas: 98/37/CEE, 73/23/CEE, 85/374/CEE, 89/366/CEE y además declara que se han aplicado las siguientes normas armonizadas: EN , EN 292, EN 294, EN 349, EN 457, EN 563, pren 77 EN 5504, EEN , EN , EN , pren Se han utilizado las siguientes (partes/cláusulas de) normas y especifi caciones técnicas nacionales: IEC Il sottoscritto, rappresentante del produttore, Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund dichiara che il prodotto: Idropulitrice ad alta pressione tipo: UNO BOOSTER / DUO BOOSTER è conforme alle disposizioni delle seguenti direttive CEE e successive modifi che: 98/37/EEC, 73/23/EEC, 85/374/EEC, 89/366/EEC e dichiara altresì che sono stati applicati i seguenti standard generali: EN , EN 292, EN 294, EN 349, EN 457, EN 563, pren 77 EN 5504, EEN , EN , EN , pren Sono stati utilizzati i seguenti standard (parti/clausole) tecnici nazionali: IEC Hadsund, de febrero de 2002 Anton Sørensen V.P. Technical Operations Europe Hadsund, febbraio 2002 Anton Sørensen V.P. Technical Operations Europe 64

26 EC Declaration of Conformity EG-Konformitätserklärung The undersigned, representing the following manufacturer, Nilfisk-ALTO, Division of Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund declares that the product: High Pressure Washer type : UNO BOOSTER / DUO BOOSTER, 400 V 3~ 50 Hz IP X5 is in conformity with the provisions of the following EC directives, with subsequent amendments: 2006/42/EC, 2006/95/EC, 2004/08/EC and furthermore declares that the following harmonised standards have been applied: EN (2006), EN 200- (2004), EN (2004), EN 77 (2000) EN (2006), EN (200), EN (2006), EN (2005), EN (2000) The following (parts/clauses of) national technical standards and spec i fi ca tions have been used: DS EN (2007) Der Unterzeichnete, der den folgenden Hersteller vertritt: Nilfisk-ALTO, Division of Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund erklärt hiermit, daß das produkt: Hochdruckreiniger Typ : UNO BOOSTER / DUO BOOSTER, 400 V 3~ 50 Hz IP X5 konform ist mit den Bestimmungen der folgenden EG-Richtlinien, inklusive deren Änderungen: 2006/42/EC, 2006/95/EC, 2004/08/EC Desweiteren erklären wir, daß die folgenden harmonisierten Normen (oder Teile/Klauseln hieraus) zur Anwendung gelangten: EN (2006), EN 200- (2004), EN (2004), EN 77 (2000) EN (2006), EN (200), EN (2006), EN (2005), EN (2000) und daß folgende nationale technische Normen und Spezifi ktionen zur Anwendung gelangten: DS EN (2007) Hadsund, Anton Sørensen General Manager, Technical Operations EAPC Hadsund, Anton Sørensen General Manager, Technical Operations EAPC Déclaration de Conformité EC Le fabricant soussigné, Nilfisk-ALTO, Division of Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund déclare que le produit : Nettoyeur haute pression type : UNO BOOSTER / DUO BOOSTER, 400 V 3~ 50 Hz IP X5 est conforme aux dispositions des directives CE suivantes, et aux amendements ultérieurs : 2006/42/EC, 2006/95/EC, 2004/08/EC et déclare également que les critères harmonisés ci-après ont été appliqués : EN (2006), EN 200- (2004), EN (2004), EN 77 (2000) EN (2006), EN (200), EN (2006), EN (2005), EN (2000) Les critères techniques et spécifi cations nationales ci-après ont été utilisés (parties/clauses) : DS EN (2007) Hadsund, Anton Sørensen General Manager, Technical Operations EAPC Verklaring van conformering aan EG-regelgeving Ondergetekende, functionerend als vertegenwoordiger van de fabrikant Nilfisk-ALTO, Division of Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund verklaart dat het product: Hogedrukreiniger type: UNO BOOSTER / DUO BOOSTER, 400 V 3~ 50 Hz IP X5 voldoet aan de eisen gesteld in de volgende EG-regels, met daaropvolgende wijzigingen: 2006/42/EC, 2006/95/EC, 2004/08/EC en verklaart bovendien dat de volgende geharmoniseerde standaarden zijn gehanteerd: EN (2006), EN 200- (2004), EN (2004), EN 77 (2000) EN (2006), EN (200), EN (2006), EN (2005), EN (2000) De volgende (delen/artikelen van) nationale technische standaarden en specifi caties zijn gebruikt: DS EN (2007) Hadsund, Anton Sørensen General Manager, Technical Operations EAPC Declaración de conformidad de la CE Dichiarazione di conformità CE El abajo fi rmante, en representación del fabricante Nilfisk-ALTO, Division of Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund declara que el producto: Hidrolimpiadora de alta presión tipo: UNO BOOSTER / DUO BOOSTER, 400 V 3~ 50 Hz IP X5 es conforme con las disposiciones de las siguientes directivas de la CE con sus consiguientes enmiendas: 2006/42/EC, 2006/95/EC, 2004/08/EC y además declara que se han aplicado las siguientes normas armonizadas: EN (2006), EN 200- (2004), EN (2004), EN 77 (2000) EN (2006), EN (200), EN (2006), EN (2005), EN (2000) Se han utilizado las siguientes (partes/cláusulas de) normas y especifi caciones técnicas nacionales: DS EN (2007) Hadsund, Anton Sørensen General Manager, Technical Operations EAPC Il sottoscritto, rappresentante del produttore, Nilfisk-ALTO, Division of Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund dichiara che il prodotto: Idropulitrice ad alta pressione tipo: UNO BOOSTER / DUO BOOSTER, 400 V 3~ 50 Hz IP X5 è conforme alle disposizioni delle seguenti direttive CEE e successive modifi che: 2006/42/EC, 2006/95/EC, 2004/08/EC e dichiara altresì che sono stati applicati i seguenti standard generali: EN (2006), EN 200- (2004), EN (2004), EN 77 (2000) EN (2006), EN (200), EN (2006), EN (2005), EN (2000) Sono stati utilizzati i seguenti standard (parti/clausole) tecnici nazionali: DS EN (2007) Hadsund, Anton Sørensen General Manager, Technical Operations EAPC 64

27 Сертификат соответствия ЕС Нижеподписавшийся, в качестве представителя следующего производителя: Nilfisk-ALTO, Division of Nilfisk-Advance A/S, Industrivej, DK-9560 Hadsund заявляет, что изделие: Высоконапорный промыватель тип: UNO BOOSTER / DUO BOOSTER, 400 V 3~ 50 Hz IP X5 Соответствует положениям следующих директив ЕС в редакции последующих изменений: 2006/42/EC, 2006/95/EC, 2004/08/EC и, кроме того, что применялись следующие согласованные стандарты: EN (2006), EN 200- (2004), EN (2004), EN 77 (2000) EN (2006), EN (200), EN (2006), EN (2005), EN (2000) Использованы следующие (части/статьи) национальных технических стандартов и спецификаций: DS EN (2007) Хатсунд, Антон Серенсен General Manager, Technical Operations EAPC 65