Oakton Community College Science and Health Careers Center Polished Water Unit Installation DRAFT

Size: px

Start display at page:

Download "Oakton Community College Science and Health Careers Center Polished Water Unit Installation DRAFT"

Agnes Wright
5 years ago
Views:

1 The water polishers should be installed according to the following: The West half of the 3 rd Floor: Legat Architects/Harley Ellis Devereaux OCC Polished Water Issue-3.0.docx 10/29/2014 Page 1 of 10

2 Center portion of the 3 rd Floor: Legat Architects/Harley Ellis Devereaux OCC Polished Water Issue-3.0.docx 10/29/2014 Page 2 of 10

340 Organic Chemistry: Option #1 Install (1) Millipore Direct-Q3 Unit with an integral 6 litter reservoir (NO

Remove the wall cabinet doors and hardware on the north wall cabinet closest to the corner so that there is no

Drill a hole in the epoxy resin countertop above the service chase located behind the base cabinets and pipe drain

south side of cabinetry. Connect the water supply to the icemaker water supply and pipe back to the water polisher.

The control unit and dispensing device on the end of the umbilical will flow down from the water polisher and set on

3 340 Organic Chemistry: Option #1 Install (1) Millipore Direct-Q3 Unit with an integral 6 litter reservoir (NO separate reservoir) on the west wall on the blank wall in the northwest corner. Remove the wall cabinet doors and hardware on the north wall cabinet closest to the corner so that there is no interference. The cabinet will remain as an open shelf cabinet. Drill a hole in the epoxy resin countertop above the service chase located behind the base cabinets and pipe drain line within this service chase behind the cabinets over to the floor drain that is located below the icemaker on the south side of cabinetry. Connect the water supply to the icemaker water supply and pipe back to the water polisher. Plug water polisher into wire mold outlet below the shelf. The control unit and dispensing device on the end of the umbilical will flow down from the water polisher and set on the counter. Option #2 Remove or modify the wall cabinet on the west wall closets to the ice machine and install the water polisher in that location. Run utilities similar to option #1. Legat Architects/Harley Ellis Devereaux OCC Polished Water Issue-3.0.docx 10/29/2014 Page 3 of 10

342 Research: Install (1) Millipore Direct-Q8 and (1) separate 30 litter Reservoir.

NOTE: This unit was originally intended to be in 335 Biology.

Pipe water from existing tap below sink and pipe water up through service column.

Use the custom Millipore wall mounting L brackets to support each device.

The control unit and umbilical will flow down from the water polisher and reset on the counter.

4 342 Research: Install (1) Millipore Direct-Q8 and (1) separate 30 litter Reservoir. Mount both devices on the face of service chase above the sink. NOTE: This unit was originally intended to be in 335 Biology. Drain tubes will hang down and empty into the sink. Pipe water from existing tap below sink and pipe water up through service column. Power Water Polisher from duplex outlet located below the sink at the back of the base cabinet. Use the custom Millipore wall mounting L brackets to support each device. Run services to water polisher through large utility opening in epoxy resin top within the Service column. The control unit and umbilical will flow down from the water polisher and reset on the counter. 320 Chemistry: Install (1) Millipore Direct-Q8 and (1) separate 30 liter Reservoir unit in base cabinet next to the sink at the back of the Lab. Pipe waste to floor drain below ice maker. Service unit with water and power installed for this unit. Legat Architects/Harley Ellis Devereaux OCC Polished Water Issue-3.0.docx 10/29/2014 Page 4 of 10

Reservoir unit in base cabinet next to the

Pipe waste to floor drain below ice maker.

5 322 Chemistry: Install (1) Millipore Direct-Q8 and (1) separate 30 liter Reservoir unit in base cabinet next to the sink at the back of the Lab. Pipe waste to floor drain below ice maker. Service unit with water and power installed for this unit. Legat Architects/Harley Ellis Devereaux OCC Polished Water Issue-3.0.docx 10/29/2014 Page 5 of 10

324 Chem Prep: Owner to relocate existing Crossbow system. Suggest mounting the two prefilter tanks of the back side of Service Chase wall.

Drain tubes will hang down and empty into the sink. Pipe water from existing tap below sink and pipe water up through service column.

There is a large utility opening in epoxy resin top within the Service column.

on the south wall to the right of the sink. NOTE: Unit originally intended for 342 Research.

Provide a water line from within the sink base cabinet up to the water polisher.

6 324 Chem Prep: Owner to relocate existing Crossbow system. Suggest mounting the two prefilter tanks of the back side of Service Chase wall. Suggest mounting final water polisher on front side of Service Chase wall above island sink. Run all services in or through the Service Chase. Drain tubes will hang down and empty into the sink. Pipe water from existing tap below sink and pipe water up through service column. Power Water Polisher from duplex outlet located below the sink at the back of the base cabinet. There is a large utility opening in epoxy resin top within the Service column. 335 Biology: Option #1: Install (1) Millipore Direct-Q3 Unit with an integral 6 litter reservoir (NO separate reservoir) on the face of the column on the south wall to the right of the sink. NOTE: Unit originally intended for 342 Research. Install unit on custom Millipore L shaped wall mounted bracket above the counter. Provide a water line from within the sink base cabinet up to the water polisher. Provide electrical power to the water polisher to the outlet below the cabinet which is located in the base cabinet to the right of the sink base cabinet. The control unit and umbilical will flow down from the water polisher and reset on the counter. Option #2: Remove the single glass door cabinet above sink and install unit on custom Millipore L Shaped wall mounted bracket above the sink. Legat Architects/Harley Ellis Devereaux OCC Polished Water Issue-3.0.docx 10/29/2014 Page 6 of 10

Modify as required 1 of the 2 existing water sources recessed in the wall. Option #1B: 15 deep shelf.

7 351 Bio Prep: Option #1A: Install (1) Millipore Direct-Q8 and (1) separate 30 liter Reservoir on the west wall next to the Glass washer GW-01. Set units on a table or cart and pipe waste water to existing floor sink that serves several other waste lines. Active blanked off power outlet. Modify as required 1 of the 2 existing water sources recessed in the wall. Option #1B: 15 deep shelf. Same as Option #1 except install adjustable wall shelf brackets and shelves and set units on Option #2: Install both units on a 15 deep shelf above counter behind sink on the north side. Use water from adjacent sink and drain waste water into sink. Option #1A & B photo: Legat Architects/Harley Ellis Devereaux OCC Polished Water Issue-3.0.docx 10/29/2014 Page 7 of 10

Option #2 Photos: 353 Micro Biology: Install (1) Millipore

sink on the south wall Mount using Millipore custom L brackets.

8 Option #2 Photos: 353 Micro Biology: Install (1) Millipore Direct-Q8 and (1) separate 30 liter Reservoir on wall above the sink on the south wall Mount using Millipore custom L brackets. Use power located behind the access panel in the base cabinet in front of the column. Plumb water located in the sink base cabinet up to the water polisher. Run the water polisher and water reservoir waste line down and into the sink. Legat Architects/Harley Ellis Devereaux OCC Polished Water Issue-3.0.docx 10/29/2014 Page 8 of 10

There are two or three different components with each water

locations: 1. Each Water Polisher, Q3 & Q8, also has a 2.

that has a large corrugated umbilical that surrounds

supported on a free standing pedestal on a counter. 3.

9 There are two or three different components with each water polishing unit as identified with each of the (7) different locations: 1. Each Water Polisher, Q3 & Q8, also has a 2. There is a remote bench top dispensing and control unit that has a large corrugated umbilical that surrounds several lines connecting it to the top of the Water Polisher. This control device can either mount to a wall or be supported on a free standing pedestal on a counter. 3. Separate water reservoir on a 5 raised base. Legat Architects/Harley Ellis Devereaux OCC Polished Water Issue-3.0.docx 10/29/2014 Page 9 of 10

10 TANKFIX01 (#14 = Bracket supporting Water Reservoir) WMBSMT001 (Bracket supporting Water Polisher) Legat Architects/Harley Ellis Devereaux OCC Polished Water Issue-3.0.docx 10/29/2014 Page 10 of 10

REVOLUTION DESIGN AND BUILD Kitchens: $50,000-$75,000. Minneapolis

REVOLUTION DESIGN AND BUILD Kitchens: $50,000-$75,000 Minneapolis PROJECT DESCRIPTION: Our clients were frustrated with their small, inefficient kitchen. The sink was undersized, the refrigerator was located