DCP3/ DETAILS OF THE CLIENT ADDRESS OF THE INSTALLATION

Transcription

1 Issued in accordance with British Standard Requirements for Electrical Installationsby a Domestic Installer enrolled with NICEIC, Warwick House, Houghton Hall Park, Houghton Regis, Dunstable LU5 5ZX DETAILS OF THE CLIENT ADDRESS OF THE INSTALLATION DETAILS OF THE INSTALLATION The installation is Extent of the installation work covered by this certificate This safety certificate is an important and valuable document which should be retained for future reference Client and FAO : Mrs H. Hodgins Mrs Hodgin Installation Deutsche Kirche address 88 Dingwall Drive Mrs Burke address Bedford Street Greasby Liverpool Wirral Postcode CH49 1SQ Postcode Rewire of Church New An addition - An alteration - Original ( To the person ordering the work ) DESIGN, CONSTRUCTION, INSPECTION AND TESTING I / We, being the person(s) responsible for the design, construction, inspection and testing of the electrical installation The extent of liability of the signatory is limited to the work described above as the subject of this ( as indicated by my / our signature adjacent ), particulars of which are described above, having excerised reasonable certificate. For the DESIGN, the CONSTRUCTION and the INSPECTION AND TESTING of the installation. skill and care when carrying out the design, construction, inspecting and testing, hereby CERTIFY that the said work for which I / We have been responsible is, to the best of my / our knowledge and belief, in accordance with Name Signature BS7671, 2001 ammended to 2004 except for the departures, if any, detailed as follows : ( CAPITALS ) Details of departures from BS7671, as amended (Regulations , ) The results of the inspection and testing reviewed by the Qualified Supervisor None Signature Name ( CAPITALS ) PARTICULARS OF THE ELECTRICAL CONTRACTOR NEXT INSPECTION $ - Enter interval in terms of years, months or weeks, as appropriate Trading I RECOMMEND that this installation is further inspected and tested after an interval of not more than 5 years Title Allerton-EPS Address Note: Enter 'None' or where appropriate, the page number(s) of 184 Mather Avenue COMMENTS ON EXISTING INSTALLATION additional page(s) of comments on the existing installation Allerton Tel Liverpool Current usage has the Petrol Lawnmower stored in the switch room - Mobile this isn't ideal - but there is little place to put it elsewhere. Postcode L18 7HD NIC Enrolment No ( essential information ) SCHEDULE OF ADDITIONAL RECORDS See attached schedule * Where the electrical work to which this certificate relates includes the installation of a fire alarm system and / or an emergency lighting system ( or a part of such systems ) this electrical safety certificate should be accompanied by the particulat certificate(s) for the system(s) This form is based on the model Electrical Installation Certificate shown in Appendix 6 of BS7671 ( as amended ). As published by NICEIC Group Limited Please see the 'Notes for Recipients' Page 1 of 6 DCP3/

2 NOTES FOR RECIPIENT THIS SAFETY CERTIFICATE IS AN IMPORTANT AND VALUABLE DOCUMENT WHICH SHOULD BE RETAINED FOR FUTURE REFERENCE IF YOU WERE THE PERSON ORDERING THE WORK, BUT NOT THE OWNER OR USER OR THE Page 1 of this certificate provides details of the electrical installation, together with the names INSTALLATION, YOU SHOULD PASS THIS CERTIFICATE, OR A FULL COPY OF IT INCLUDING and signatures of the persons certifying the installation work and reviewing the results of THESE NOTES, IMMEDIATELY TO THE OWNER OR USER OF THE INSTALLATION. inspection and testing on behalf of the Approved Contractor responsible for the work, details of which are also given on that page. This safety certificate has been issued to confirm that the electrical installation work to which it relates has been designed, constructed, inspected, tested and verified in accordance Certification provides an assurance that the electrical installation work has been fully inspected with the national standard for the safety of electrical installations, British Standard 7671 (as and tested, and that the work has been carried out in accordance with the requirements of amended) - Requirements for Electrical Installations ( the IEE Wiring Regulations ). BS 7671 ( except for any departures recorded in the appropriate part of the certificate ). Where, as will often be the case, the installation incorporates a residual current device All unshaded boxes should have been completed either by the insertion of the relevant details or by (), there should be a notice at or near the consumer unit stating that the device should be entering 'N/A', meaning 'Not Applicable', where appropriate. tested at quarterly intervals. For safety reasons, it is important that you carry out the test regularly. Where the electrical work to which this certificate relates includes the provision of a mainspowered fire detection and alarm system ( such as one or more smoke alarms), this electrical Also for safety reasons, the complete electrical installation will need to be inspected and safety certificate must be accompanied by a separate certificate for that system in accordance tested at appropriate intervals by a competent person. The NICEIC* recommends that you with British Standard 5839: Part 6 - Code of Practice for the design and installation of fire engage the services of an Approved Contractor for this purpose. detection and alarm systems in dwellings. The maximum interval recommended before the next inspection is stated on Page 1 under Next Inspection. There should also be a notice at or near the consumer unit Should the person ordering the work ( eg the client, as identified on Page 1 of this certificate) indicating when the inspection of the installation is next due. have reason to believe that any element of the electrical work for which the Approved Contractor has accepted responsibility ( as indicated by the signature(s) on this certificate) does not comply with the requirements of the national electrical safety standard (BS7671), the person should in Only the NICEIC Approved Contractor or Conforming Body responsible for the construction of the the first instance raise the specific concerns in writing to the Approved Contractor. If the electrical installation is authorised to issue this NICEIC certificate. concerns remain unresolved, the client may make a formal complaint to NICEIC, for which purpose a standard complaint form is available on request. The Electrical Installation Certificate consists of at least three pages. The certificate is invalid if the second or third pages ( containing schedules ) are missing. The certificate has a printed seven-digit serial number which is traceable to the Approved Contractor to which it was The complaints procedure offered by NICEIC is subject to certain terms and conditions, full supplied. details of which are available upon application and from the website. NICEIC does not investigate complaints relating to the operational performance of electrical installations (such as This certificate is intended to be issued only for the initial certification of a new electrical lighting levels), or contractual or commercial issues ( such as time or cost ). installation, or for new work associated with an alteration or addition to an existing electrical installation, in a single dwelling ( house or individual flat ). For new electrical installation work in * ''NICEIC' is a trading name of NICEIC Group Limited, a wholly owned subsidiary of the Electrical Safety other than a single dwelling, a full Electrical Installation Certificate should have been issued. Council. Under licence from The Electrical Safety Council, NICEIC acts as the electrical contracting industry's independent voluntary regulatory body of electrical installation safety matters throughout the This certificate should not have been issued for reporting on the condition of an existing UK, and maintains and published registers of electrical contractors that it has assessed against electrical installation. A Periodic Inspection Report or an Electrical Installation Periodic particular scheme requirements ( including the technical standard of electrical work ) Inspection Report should be issued for such an inspection. You should have received the certificate marked 'Original' and the Approved Contractor should have retained the certificate marked 'Duplicate'. The 'Original' certificate should be kept in a safe place and shown to any person inspecting or undertaking work on the electrical installation in the future. If you later vacate the property, this certificate will demonstrate to the new owner or user that the electrical installation work complied with the requirements of the national electrical safety standard at the time the certificate was issued. As published by NICEIC Group Limited Copyright the Electrical Safety Council ( July 2006 ) For Further information about electrical safety and how NICEIC can help you visit DCP3/

3 SUPPLY CHARACTERISTICS Nature of supply parameters Characteristics of primary supply Tick boxes and enter details, as appropriate Notes: (1) by enquiry, (2) by enquiry or by measurement, (3) where more than one supply, record the higher or highest values overcurrent protection device(s) System type(s) Number and type of live conductors Nominal voltage(s) U (1) 230 V (1) U V BS(EN) 3036 TN-S - - (2 wire) (3 wire) Nominal frequency f (1) 50 Hz Type - Prospective (2)(3) Nominal current TN-C-S - (2 wire) - (3 wire) - I fault current pf 2.24 ka rating 100 A TT - Other Please state External earth fault (1) Short-circuit 3 phase Z 0.80 Ω loop impedance e capacity - ka PARTICULARS OF INSTALLATION AT THE ORIGIN Tick boxes and enter details, as appropriate Main switch or circuit-breaker Means of Earthing Details of installation earth electrode ( where applicable ) Measured Z e 0.10 Ω BS(EN) Voltage 250 V Distributor's Type (eg rod(s), rating Facility - Location - Maximum A per tape etc) No of Current demand (Load) phase A Installation Electrode Method of poles rating,i - - Ω earth electrode measurement - n resistance, R A Supply operating 1 COPPER - Number of smoke alarms conductors material Supply operating conductors 25mm Earthing conductor Main equipotential bonding conductors and bonding of extraneous-conductive-parts () csa time (at I Δn ) * - ms Water Oil Gas material COPPER material COPPER service service - service - Continuity Structural Other incoming csa 16 mm 2 check csa 10 mm 2 steel - service(s) - * - applicable only where an is used a main circuit breaker current, I Δn * ma Original ( To the person ordering the work ) SCHEDULE OF ITEMS INSPECTED Tick boxes and enter details, as appropriate General Presence and correct location of appropriate Methods of protection against electric shock Preventation of mutual detrimental influence Identification ( contd ) devices for isolation aand switching Proximity of non-electrical services and Labelling of protective devices Adequacy of access to switchgear Insulation of live parts, and barriers or enclosures other influences switches and terminals and other equipment Presence of (s) for supplementary protection n/a Segregation of Band I and Band II cicuits Identification of conductors n/a Particular protective measures for against direct contact and/or protection against or Band II insulation used special installations and locations indirect contact Cables and conductors Presence of earthing conductor and Routing of in prescribed zones Connection of single-pole devices for protection Electrical separation circuit protective conductors or within mechanical protection or switching in phase conductors only Presence of main equipotential equipotential bonding Connection of conductors Correct connection of accessories and equipment conductors Identification n/a Presence of supplementary equipotential bonding Presence of diagrams, instructions, Choice and settings of protective devices ( for protection Erection methods conductors circuit charts and similar information against indirect contact and/or overcurrent ) n/a Selection of conductors for current- Selection of equipment and protective Class II fixed equipment Presence of danger notices carrying capacity and voltage drop measures appropriate to external influences Presence of other warning notices, including Presence of fire barriers, suitable seals Selection of appropriate functional switching n/a SELV presence of mixing wiring colours and protection against thermal effects devices Insulation resistance between live SCHEDULE OF ITEMS TESTED conductors Earth fault loop impedance, Z e External earth fault loop impedance, Z e Continuity of protective conductors Insulation resistance between live conductors and earth Operation of residual current device(s) Installation earth electrode resistance, R A Continuity of ring final circuit conductors Polarity Functional testing of assemblies All boxes must be completed. '' indicates that an inspection has been carrid out and that the result was satisfactory. N/A indicates that an inspection or test was not applicable to the particular installation. Page 3 of 6 This form is based on the model Electrical Installation Certificate shown in Appendix 6 of BS7671 ( as ammended ) As published by NICEIC Group Limited Copyright the Electrical Safety Council ( July 2006 )

4 ADDITIONAL RECORDS ADDITIONAL NOTES ON EXISTING INSTALLATION Organ Light cannot have passed a PAT test. DETAILS OF ANY DEPARTURES There are no departures to the 16th Edition Wiring Regulations Page 4 of 6

5 CIRCUIT DETAILS TEST RESULTS Designation Designation ( For Distribution s, insert 'D' ) ( use the word "Ring" where appropriate ) Position Type of Wiring ( see code ) Reference Method ( see Appendix 4 of BS7671 ) Number of Points Served s ( csa ) Max Disconnection Time Overcurrent Protective Device All s Polarity Operation - counting from Isolator live cpc BS ( EN ) Type Rating Capacity R ½ x5 phase neutral cpc 1 + R 2 R x1 2 (30mA) mm 2 mm 2 s Amps ka ma Ω Ω Ω Ω Ω Ω MΩ MΩ MΩ MΩ Ω ms Origin ( meter tails ) BR >199 >199 >199 > BL 2 Supply to Back Hall Heater's Isolator H MET 5 BS >199 >199 >199 > GR >199 >199 >199 > Supply to Vestry Consumer 2BR 4 A BS >199 >199 >199 > Unit 2BL 5 Reception Heater D/B BS >199 >199 >199 > GR 6 Reception Lights D/B BS C >199 >199 >199 > BR 7 Fire Alarm Control Unit D/B BS >199 >199 >199 > BL 8 Not Used BS GR 9 Back Hall Lights B/E BS >199 >199 >199 > BR 10 Altar Lights & Back Lights B/E BS >199 >199 >199 > BL 11 Heater 1 ( nearest Altar ) D/B BS >199 >199 >199 > GR 12 Not Used BS Church Lights ( front and 5BR 13 D/B BS B >199 >199 >199 > vestry ) 5BL 14 Heater 2 ( church middle ) D/B BS >199 >199 >199 > GR 15 Lights - Toilet & Kitchen D/B BS B >199 >199 >199 > Church Lights Centre 6BR 16 and Switch Room D/B BS C >199 >199 >199 > BL 17 Heater 3 ( church furthest ) D/B BS >199 >199 >199 > GR 18 Not Used BS Operating Current Maximum Z S Impedances Ring s only measured end to end r 1 r n r 2 Neutral Insulation Resistance / Neutral Neutral Earth Loop Impedance Z S Push button Maximum Demand Remarks Location of Designation of Prospective fault current In the ante-room to the left of the alter. consumer unit(s) consumer unit(s) at consumer unit(s) 2.24 ka TEST INSTRUMENTS Insulation Resistance Test instrument's ( serial numbers ) used Continuity Earth electrode resistance Earth fault loop impedance This form is based on the model Electrical Installation Certificate shown in Appendix 6 of BS7671 ( as amended ) - As laid out the Electrical Safety Council ( July 2006 ) * - See notes on schedule of test results Allerton-EPS TYPE OF WIRING A B C D E F G H O - ( Other - Please Specify ) PVC / PVC PVC in metallic conduit conduit PVC in metallic trunking trunking PVC / SWA XLPE / SWA Mineral-insulated Page 5 of 6

6 CIRCUIT DETAILS TEST RESULTS Designation Designation ( For Distribution s, insert 'D' ) ( use the word "Ring" where appropriate ) Position Type of Wiring ( see code ) Reference Method ( see Appendix 4 of BS7671 ) Number of Points Served s ( csa ) All s Polarity Operation - counting from Isolator live cpc BS ( EN ) Type Rating Capacity R 1 + R 2 R ½ x1 2 x5 phase neutral cpc (30mA) mm 2 mm 2 s Amps ka ma Ω Ω Ω Ω Ω Ω MΩ MΩ MΩ MΩ Ω ms DB5 Dist Board Socket Ring in Back Hall B BS EN B >199 >199 >199 > Kitchen Sockets DB4 B BS EN B >199 >199 >199 > Cooker B BS EN B > Sockets B BS EN B >199 >199 >199 > DB2 VESTRY Dist Board Socket Ring BH BS Nearest Heater B BS >199 >199 3 Middle Heater B BS >199 > Furthest Heater B BS >199 > DB3 BACK HALL Dist Board 4 MET BR 1 Left 6KW Heater C BS > BL 2 3KW Heaters C BS GR 3 Right 6KW Heater C BS > DB4 KITCHEN Dist Board Max Disconnection Time Overcurrent Protective Device Operating Current 1 Kitchen Socket Ring B BS >199 >199 >199 > Maximum Z S Impedances Ring s only measured end to end r 1 r n r 2 Neutral Insulation Resistance / Neutral Neutral Earth Loop Impedance Z S Push button Maximum Demand Remarks Little White Consumer Board to the right of the DB1 ( main board ). values apply to the Socket under alarm panel TEST INSTRUMENTS Insulation Resistance Test instrument's ( serial numbers ) used Continuity Earth electrode resistance Earth fault loop impedance This form is based on the model Electrical Installation Certificate shown in Appendix 6 of BS7671 ( as amended ) - As laid out the Electrical Safety Council ( July 2006 ) * - See notes on schedule of test results Allerton-EPS TYPE OF WIRING A B C D E F G H O - ( Other - Please Specify ) PVC / PVC PVC in metallic conduit conduit PVC in metallic trunking trunking PVC / SWA XLPE / SWA Mineral-insulated Page 6 of 6