Installation & Programming Manual. Ness AIR2 Wireless Devices. Innovative Electronic Solutions

Transcription

1 N N N T014 T014 Ness IR2 Wireless evices Installation & Programming Manual Innovative lectronic Solutions

2 Wireless devices Table of contents hapter 1 eneral information bout this manual Supplier's details Products description ir2-s100 transceiver ir2-ir100 and ir2-ir100/ PIR detectors ir2-m100 magnetic contact ir2-m200 magnetic contact ir2-k100 remote-control keyfob ir2-100 smoke detector hapter 2 Operating principles ir2-s100 address Wireless terminals hapter 3 Installation Installing the ir2-s Installing the IR100 and IR100/ Installing the ir2-m Installing the ir2-m Installing the ir2-k Installing the ir ddressing the ir2-s nrolling the devices hapter 4 Programming Programming via keypad Programming via the ir2-s100 module ir2-s100 module default settings Options programmable at the control panel ppendix ir2-s100 declaration of conformity ppendix Order odes

3 Installation and programming manual hapter 1 NRL INORMTION bout this manual MIIN02S Suppliers's details Supplier: Ness orporation ddress: 4/167 Prospect wy, Seven ills, NSW, 2417, ustralia Tel.: customerservice@ness.com.au Web: The persons authorized by the manufacturer to repair or replace the parts of this system, hold authorization to work on Ness orporation brand devices only. 1-1 MNUL O VRSION 1-2 Products description The advanced ir2 two-way wireless intrusion protection system (915Mz frequency) integrates directly with all models in Ness s SmartLiving Series intrusion control panel range Technical specifications of ir2 system requency band Mz Transmit R power < 10mW (e.r.p.) Operating frequency 915.1Mz 915.3Mz Spurious emission Operating < 930 nw (selectable) 915.5Mz level for mode frequencies above 1z Stand-by requency stability +/-11kz mode < 2 nw ommunication type Two-way etector supervision from 12 to 120 min. Modulation SK Security grade 2 hannels 3 nvironmental class II ir2 system devices: ir2 S100/50 transceiver module, 50 terminals (Ness Part No ) ir2 S100/10 transceiver module, 10 terminals (Ness Part No ) ir2 IR100 passive infrared detector, 12m (Ness Part No ) ir2 M100 magnetic contact with two I/O terminals, (Ness Part No ) ir2 M200 magnetic contact with shock and tilt sensor (Ness Part No ) ir2 K100 4 button remote-control key (Ness Part No ) ir2 100 smoke detector (Ness Part No ) ach SmartLiving control panel supports more than one ir2-s100, module connected via I-US cable, according to the table: Number of ir2-s100 managed by the control panel ontrol panel W SmartLiving control panel Not supported eneral information 3

4 Wireless accessories This accurate and operationally cost-effective wireless security solution performs best when the ir2-s100 transceiver module is situated at the core of the wireless network, in a location which allows easy connection of the I-US cable to the control panel. ll wireless protection devices should be installed in elevated positions in order to increase detection capabilities and prevent inadvertent blinding caused by sizeable objects or building occupants. To streamline the installation process, view the signal strength (transmitted/ received by the ir2-s100 transceiver module) of each device in the wireless network via the system keypads and SmartLeague software. s an integral part of the system, the ir2 provides 3 inter-module transmission channels. This feature allows you to select the channel in such way as to avoid over-the-air interference between two close-proximity wireless systems (for example, in two adjoining apartments). or secure deployment and operations of the ir2 wireless intrusion protection system, it is necessary to refer to the Installation and programming guide of the hardwired intrusion control panel in use. ir2-s100 transceiver The ir2-s100 transceiver module integrates wireless devices (detectors, keyfobs, etc.) into the hardwired environments of all models of Ness s SmartLiving intrusion control panels. The module simulates: a reader, at a pre-programmed address (), which allows you to configure the keyfobs up to 10 expansion boards, at addresses, +1,... +9, capable of managing the terminals Technical specifications ir2-s100/ 50 ir2-s100/ 30 ir2-s100/ 10 Voltage V= Maximum current draw m Operating temperature and humidity , 93% imensions (W x x ) 80 x 170 x 25 mm Weight 130 g Terminals Keyfobs Security grade 2 nvironmental class II 1-4 I J Terminals + S - for connection to the control panel US Terminal T1 (for future use) ir2-s100 P Tamper microswitch: Open cover Tamper microswitch: islodgement evice address IP microswitch strip ir2-s100 ackbox K utton P1 utton P2 L 1 - yellow L M L I J L 2 - green L 3 - green O K ntenna L Mounting screw location M Tamper screw hole N O able entry nclosure screw hole L N L 4 eneral information

5 Installation and programming manual The meanings of the signals provided on the Ls are as follows: L 1 L 2 L 3 Signal iscontinuous flashing Off Off Wireless data reception Off iscontinuous flashing Off Programming (see Programming) Off Off iscontinuous flashing Programming (see Programming) Off Off ontinuous flashing nrolling (requested at the control panel) Off ontinuous flashing ontinuous flashing rroneous programming (for example, two devices on the same terminal) 1 flash 1 flash 1 flash Reset factory default settings ir2-ir100 and ir2-ir100/ PIR detectors 1-5 ir2-ir100 is a two-way communication PIR detector with 12m coverage. The device is protected against dislodgement and open-cover tamper. You can adjust the device sensitivity (accepted value between 1 and 4) from the keypad or through the SmartLeague software application. The ir2-ir100/ PIR detector has the same features as the ir2-ir100 but covers a greater distance (20m) with a minor angle. Technical specifications ir2-ir100 ir2-ir100/ attery Lithium R123 3V (included) attery life 3 years Low battery fault voltage Less than 2.4V Stand-by current draw 51µ Maximum current draw 30m PIR range 12 m 20 m Lens angle to 6m 7 to 20m Operating temperature and humidity , 93% imensions (W x x ) 58 x 100 x 44 mm Weight 80g Security grade 2 nvironmental class II ir2-ir100 - ackbox attery ir2-ir100 - P ntenna Signalling L - red PIR detector Open-tamper microswitch NROLL microswitch I Mounting screw hole Tamper screw hole nclosure screw hole I eneral information 5

6 Wireless accessories The coverage in the following diagram refers to detectors with maximum sensitivity settings. (Note: ir2-ir100/ urtain detector optional) ir2-ir100 (Std) Top view ir2-ir100/ (Optional) m ir2-ir100/ Side view ir2-ir100 Side view m 2.2m 2.2m m m ir2-m100 magnetic contact The ir2-m100 magnetic contact has two screw-in positions for placement optimization of the device magnet, 90 one from the other. It also provides larms two terminals which can be configured as inputs or opencollector outputs. onfiguring the terminals as inputs provides standard zone management (NO, N, Single alancing, ouble alancing) and allows direct connection to rollerblind sensors. larms deriving from magnetic contacts and distinctly from the two terminals are signalled separately on the control panel. The device is protected against dislodgement and open-cover tamper. 1-6 Technical specifications of the ir2-m100 attery Lithium R123 3V (included) attery life 4 years Low battery fault voltage Less than 2.4V Stand-by current draw 21µ Maximum current draw 30m Open-collector output Max 50 m Operating temperature and humidity , 93% imensions (W x x ) 36 x 95 x 26 mm Weight 130 g Magnet dimensions 13 x 40 x 14 mm olours White, rown Security grade 2 nvironmental class II 6 eneral information

7 Installation and programming manual I J K L M N O P Q attery ntenna Signalling L - red Open-tamper microswitch islodgement-tamper microswitch NROLL microswitch N terminal Terminal T1 Terminal T2 Map of terminals Reed contact: short side Reed contact: long side Mounting screw hole Tamper screw hole Magnet - short side Magnet - long side nclosure screw hole I O N J - R123 3V + M ir2-m100 - P ir2-m100 ackbox P L M Q K x P z y O The following table indicates the distance in millimetres of the operating capacity of the magnet depending on the side in use and the axes illustrated in the figure (values starting from a nominal distance of 10mm, except for axis y-): xis ontact long side ontact short side Withdrawn Near Withdrawn Near x y z +/ In order to comply with the N series of standards, double balancing is required when either terminal T1 or T2 is configured as an input. erromagnetic materials which are located in the vicinity of the mounting position can influence the magnetic field and can result in malfunction. TTNTION! ir2-m200 magnetic contact The ir2-m200 is supplied with a magnet which is to be secured (by means of two screws) to the side of the contact, in the position indicated by the two notches. The ir2-m200 integrates a shock and tilt sensor that allows its use without the need of the magnet. The ir2-m200 is equipped with open and dislodgement tamper protection. The device uses separate channels for the different types of signalling,, thus allowing precise identification of the alarm source. ir2-m200 technical specifications attery R2 3V Lithium (included) attery life 4 years Low battery fault voltage Less than 2.4V Stand-by current draw 10µ Maximum current draw 30m Operating temperature and humidity , 93% imensions (W x x ) 35 x 58 x 23 mm Weight 30 g Magnet dimensions 13 x 40 x 14 mm olours White, rown Security grade 2 nvironmental class II 1-7 eneral information 7

8 attery Signalling L - red (on rear) Microswitch: open/ dislodgement/nroll Reed contact Mounting screw hole Tamper screw hole Securing screws Magnet position notches ir2-m200 - P - R2-3V + The following table indicates the distance in millimetres of the operating capacity of the magnet depending on the side in use and the axes illustrated in the figure (values starting from a nominal distance of 10mm, except for axis y-): xis ontact long side Withdrawn Near x y z +/ x z y Wireless accessories ir2-m200 - box MNT TTION RN The signalling of shock waves is achieved through tri-axial vibration sensor. The vibration sensibility can be set either from a keypad or via the SmartLeague software application. The signalling of tilting (angle change) is achieved through tri-axial tilt sensing. The tilt-variation value (angle) can be set in relation to the standby position, which is saved to the memory during the reset-after -alarm phase. If both shock and tilt sensing are activated, alarm signalling will occur as soon as one of the two conditions exceeds it respective alarm threshold. erromagnetic materials which are located in the vicinity of the mounting position can influence the magnetic field and can result in the reduced operating capacity of the device. SOK TTION TILT TTION TTNTION! ir2-k100 remotecontrol keyfob The ir2-k100 keyfob has 4 button which can be programmed from the control panel. The graphic-choice feature allows you to identify the buttons by numbers or icons. Technical specifications of the ir2-k100 attery Lithium R2032 3V (included) Low battery fault voltage Less than 2.4V Stand-by current draw 0 Maximum current draw 30m uzzer Multitone Operating temperature and humidity , 93% imensions (W x x ) 61 x 41 x 12 mm Weight 15 g Rubber push-buttons with icons with numbers Security grade 2 nvironmental class II Number of available PIN code combinations eneral information

9 Installation and programming manual Key1/1, L1-red Key2/2, L2-red Key3/3, L3-red Key4/4, L4-red onfirmation L - red/green Icon graphic keys lphanumeric keys The ir2-k100 keyfob imparts audible and visual feedback signals (beep and L signals) which notify the user of the successful outcome of requested operations. The meanings of the signals provided on the Ls are as follows: Push button L 1 L 2 L 3 L 4 uzzer signal Operation 1 1 flash beep ctivates shortcut flash beep ctivates shortcut flash beep ctivates shortcut flash beep ctivates shortcut flash 1 flash beep Lock/Unlock wireless keyfob flash 1 flash beep nrolling ny 4 flashes 4 flashes Keyfob locked signal ailure of the L to light, after pressing the corresponding button and the successful execution of the command, is an indication that the wireless battery is running low. Panel response onfirmation L green red uzzer signal ommand not received 1 flash Operation not done 4 flashes bop Operation done 3 flashes long beep The rolling-code feature provided by the ir2-k100 wireless keyfob allows the ir2-s100 module to authenticate all wireless-client transmissions, via use of over-the-air random codes. In the event of irregular wireless-client activity, denial-of-request will be signalled by an audible error signal ( bop ). This feature is active at default but can be disabled during the programming phase of the ir2-s100 module (details follow). If an ir2-k100 wireless keyfob is used on several systems, it is impractical to leave this feature enabled. ROLLIN-O UTNTITION ir2-100 smoke detector The ir2-100 detector is capable of sensing the presence of smoke particles and thus detecting a fire in its early stages. ir2-100 optical smoke detector is equipped with a sampling chamber (based on light scattering mass - Tyndall effect). In order to ensure the proper operating capacity of the device, it must be installed away from drafts and large objects which may alter the airflow to the sampling chamber. The sole task of the ir2-100 smoke detector is to sense for smoke in the protected area. Therefore, in no way can the combination of a SmartLiving system and an ir2-100 smoke detector be considered a fire control system. 1-9 TTNTION! eneral information 9

10 Wireless accessories ir2-100 technical specifications attery R V Lithium (included) attery life 3 years Low battery fault voltage Less than 2.4V urrent draw during standby 70µ urrent draw during alarm Max 40m Operating temperature and humidity , 93% eight (base included) 60mm iameter (base included) 114mm Weight (base and battery included) 182 gr The operating parameters can be changed and adapted to the environmental conditions, either from the control panel or through the SmartLeague software application. The detector signals alarm status when the level of smoke in the protected environment reaches the following levels: 0.08 d/m (pre-set mode) 0.10 d/m 0.12 d/m 0.15 d/m etector L red/yellow/green Optical chamber attery Tamper microswitch NROLL microswitch ase Mounting screw hole The tricolour L (360 visibility) indicates the detector status. reen - one flash every 15 seconds: detector not operating properly. reen - one flash every 40 seconds: low battery. Yellow - On solid: fault present. Yellow - flashing: sampling chamber contaminated (with dust, etc.). Red - On solid: detector in alarm status. 10 eneral information

11 Installation and programming manual hapter 2 OPRTIN PRINIPLS ir2-s100 address To enroll the ir2-s100 on the control panel, set the IP-switch strip to an ( ) between 1 and 16. The selected address will be assigned to the simulated reader (which processes and manages wireless transmissions in the same way as keys) and to the first 10 expansion boards, also simulated, with successive addresses, +1,..., +9. onditions for secure deployment and operations: the simulated reader must be enrolled on the control panel the simulated reader cannot share its address with any other hardwired reader (ny/x, ny/s, JOY/MX) the simulated reader need not be associated with any partitions the simulated expansion boards must be enrolled on the control panel an expansion board will be considered part of the wireless network only when one of its terminals is configured as wireless a simulated expansion board cannot share its assigned address with other hardwired LX5 expansion boards. Wireless terminals terminal can be considered a Wireless terminal only under the following conditions: it must not be configured as a ouble zone () if configured as a Zone, it must not be configured as Shock in the detector type field it must be assigned to an expansion board (and not to the control panel or keypads) Operating principles 11

12 Wireless accessories hapter 3 INSTLLTION Installing the ir2-s hoose a suitable mounting placement. 2. Using a flat-bladed screwdriver in the enclosure screw location, push open the enclosure and separate the two parts. 3. old the base to the chosen mounting placement and mark the screw holes and tamper protection position. 4. Pull the wires through the cable entry and wire up the ir2-s Using the screws, secure the base and the tamper protection in position. 6. nroll the device. 7. Re-attach the cover to the base and replace the enclosure screw. Installing the IR100 and IR100/ 1. hoose a suitable mounting placement. 2. Using a flat-bladed screwdriver in the enclosure screw location, push open the enclosure and separate the two parts. 3. Push the board grip to release and remove the P. 4. Open the anchor-screw holes. 5. old the base to the chosen mounting placement and mark the screw holes and tamper protection position. 6. Using the screws, secure the base and the tamper protection in position. 7. Replace the P. 8. Insert the battery, ensure you respect the proper polarity. 9. nroll the device. 10. Re-attach the cover to the base and replace the enclosure screw. The recommended installation height is 2.2m. e careful not to drill in the vicinity of electrical wiring or plumbing/gas pipes, etc. void installing the detector close to the following sources of interference: reflective surfaces, direct air flow from vents, drafts, fans, windows, sources of steam, sources of oil vapour, sources of infrared rays, and objects which can cause temperature changes such as heaters, refrigerators and ovens. o not place large objects (machinery or furniture) in front of the detector. The alarm L must be above the lens. Installing the ir2-m hoose a suitable mounting placement. 2. Using a flat-bladed screwdriver in the enclosure screw location, push open the enclosure and separate the two parts. 3. Push the board grip to release and remove the P. 4. If you use terminal T1 or T2, open the respective wire entry and pull the wires through. 5. old the base to the chosen mounting placement and mark the screw holes and tamper protection position. 6. Using the screws, secure the base and the tamper protection in position. 7. Replace the P. 8. Insert the battery, ensure you respect the proper polarity. 9. nroll the device. 10. If you wish to fit the magnet by means of the screws (included), remove the magnet base by means of a flat-bladed screwdriver NOTS Installation

13 Installation and programming manual 11. Locate the magnet (long or short side in the required position) on the contact, at a distance of about 2 mm from the magnetic reed contact. If you are using the long side, use the notches on the base in order to position it correctly. 12. Using the screws or the adhesive tape, attach the magnet. 13. Re-attach the cover to the base of the contact and replace the enclosure screw. Installing the ir2-m hoose a suitable mounting placement. 2. Using a flat-bladed screwdriver in the enclosure screw location, push open the enclosure and separate the two parts. 3. old the base to the chosen mounting placement and mark the screw holes and tamper protection position. 4. Using the screws, secure the base and the tamper protection in position. 5. Insert the battery, ensure you respect the proper polarity. 6. nroll the device. 7. If you wish to fit the magnet, work through the steps described in the previous paragraph. 8. Re-attach the cover to the base of the contact and replace the enclosure screw. Installing the ir2-k100 The ir2-k100 requires enrolling only. If it becomes necessary to replace the device cover or battery, work through the following steps. 1. Remove the enclosure screw on the back of the keyfob and open the device. 2. Remove the cover. 3. Replace the cover/battery as required. 4. lose the device and replace the enclosure screw. 5. nroll the key. Installing the ir hoose a suitable mounting placement. 2. old the base to the chosen mounting placement and mark the screw locations. 3. Insert the battery, ensure you respect the proper polarity. 4. ttach the battery cover. 5. Position the detector over the base and, with minimum force, turn it clockwise until notch aligns with notch (in order to attach the detector to the base); turn it still further until notch aligns with notch (in order to allow the base to close the tamper microswitch). 6. nroll the device ddressing the ir2-s Plan the layout of all the mounting placements of the ir2 devices. 2. Using the IP-switch of the ir2-s100 module, configure the address ( ) of the first expansion board that is to manage the wireless terminals. 3. Include the wireless expansion boards in the control panel configuration, starting from the address (maximum +9). 4. nroll the wireless reader at the address. 3-7 Installation 13

14 Wireless accessories nrolling the devices 1. Select the expansion board at the address and then select the terminal in question. 2. onfiguring the terminal as Wireless : Via keypad: press key ; the word Wireless will appear on the last line on the display Via SmartLeague: using the right button on the mouse, select Wireless. If any terminal on the expansion board is configured as wireless, all the remaining terminals must be configured as wireless terminals. 3. onfiguring the type of terminal: INPUT - for ir2-ir100 and ir2-m100 devices OUL ZON - for ir2-m200 devices 4. nrolling the wireless terminals. rom a keypad: access the zone programming section by pressing the key. o to the Wireless section and enroll the terminal by selecting one of the following: Infrared detector for ir2-ir100 Magnetic ontact for ir2-m100 Terminal T1 M or Terminal T2 M for devices connected to the terminals of the ir2-m100 Smoke detector for ir2-100 Magn.ont. M200 for ir2-m200 rom SmartLeague: double-clicking on the configured terminal will open a window where you can programme the zone. The lower part of the window shows the Wireless section, right-click and select the Wireless option. Select the type of device, by means of the Type field, then start the guided enrolling process by pressing the nroll button. 5. or ir2 devices press the NROLL key. 6. If you are enrolling and output device that is connected to a terminal of the ir2-m100, you must enable the roadcast R zone option in this section. Once done, you must step back to the configuration of the terminal and configure it as an OUTPUT. 7. nroll all the ir2-k100 wireless keyfobs in the same way as you would enroll ordinary proximity keys, selecting the reader with the address. 8. Set the parameters of the zones, outputs and keypads. 3-8 TTNTION! 14 Installation

15 Installation and programming manual hapter 4 PRORMMIN Programming via keypad If you wish to carry out the programming process via keypad (parameter settings, enrolling, deleting wireless modules, etc.), refer to the Installation and Programming guide supplied with the intrusion control panel. To program a SmartLiving 1050 control panel which requires: 12 hardwired zones of which 3 on the control panel, 2 on a keypad, 7 on 2 expansion boards 18 wireless zones 5 wireless keyfobs Minimum requirements: 18/5=4 expansion boards; if 2 expansion boards are for the hardwired zones assign them to addresses 1 and 2; set the ir2-s100 IPmicroswitches to address 3 ( ). nroll expansion boards 3, 4, 5 and 6 and reader 3 on the control panel. In the Terminals programming section, select terminal T1 of expansion board 3 and enroll the detector. nroll all the wireless devices consecutively. In the Keys-nroll programming section, select reader 3 then select the number of wireless keyfobs you wish to enroll. 4-1 XMPL Programming via the ir2-s100 module lthough partial programming using this method is possible, the manufacturer strongly recommends that programming is carried out via the SmartLeague software or via keypad through the Installer menu. Using the buttons and Ls on the P of the ir2-s100 module, carefully work through the 5 programming phases, as follows: key P1 allows access to the 5 programming phases which run cyclically ( N PRO N PRO. etc.), by pressing successively key P1 key P2 allows changes (where workable) L L3 indicates the current programming phase L L2 indicates the current data value (where effective) 4-2 nrolling: Press the NROLL button on the detector you wish to enroll. Press simultaneously keys 3 and 4 on the wireless keyfob. Within 4 seconds, L L1 should flash to indicate that the detector/keyfob has been received and enrolled. L L2 will remain Off. Unenrolling: Press the "NROLL" button on the detector you wish to unenroll (delete). Press simultaneously keys 3 and 4 on the wireless keyfob. Within 4 seconds, L L1 should flash to indicate that the detector/keyfob has been received and unenrolled. L L2 will remain Off. hange transmission/reception channel: L L2 emits a number of flashes equal to the channel currently operative. 3 channels are available. Press button P2 to activate the successive channel to the one currently operative on the ir2- S100 module. t this point, press the NROLL button on all the detectors, and to press keys 3 and 4 simultaneously on all the keyfobs. This will synchronize the system wireless devices with the new channel. PS 1 PS 2 PS 3 Programming 15

16 Wireless accessories nable/isable tamper ir2-s100: L L2 indicates the status of this option: O = Tamper enabled; ON = Tamper disabled. Press button P2 to toggle the status of this option. If the Tamper option is disabled, the status of both microswitches will be ignored. nable/isable rolling-code authentication on all ir2-k100 keys: L L2 indicates the status of this option: O = Rolling code authentication enabled; ON = Rolling code authentication disabled. Press button P2 to toggle the status of this option. PS 4 PS 5 ir2-s100 module default settings 4-3 To restore the factory default settings, press and hold key P2 until the three Ls are ON, during the Phase 2 - Unenroll, shown in the former paragraph. o not use batteries other than those indicated by the manufacturer as they may explode. Used batteries must be disposed in accordance with local regulations. TTNTION! Options programmable at the control panel 4-4 You can set the following options for the wireless zones during the programming phase of the SmartLiving control panel: Option If enabled If disabled TampReed/ollPir roadcast R Use sensor L ir2-ir100 - in order to increase the life of the batteries, the infrared detector is deactivated when its partitions are disarmed and activated when its partitions are armed. isabled detectors cannot generate alarms. When the partitions arm, there may be a delay of up to 3 minutes before the detector receives the activation command. ir2-m100/m200 - detects tamper on the magnetic contact. This option must be enabled when the zone and one of the ir2-m100 terminals ( T1 or T2 ) is configured as an output. ssures the activation/ deactivation of the output within two seconds of the control panel command. The red L of ir2-ir100 and ir2- M100/M200 devices signal alarm or tamper on the device. TTNTION! ir2-ir100 - the PIR detector will be active at all times. ir2-m100/m200 - tamper conditions on the magnetic contact will not be detected. The activation/deactivation of the wireless output occurs within two minutes of the command from the control panel. The red L of ir2-ir100 and ir2-m100/m200 devices is always Off. In the case of an ir2-m100 device, this option should be enabled on all its terminals. 16 Programming

17 Installation and programming manual ppendix IR2-S100 LRTION O ONORMITY eutsch: iermit erklärt Ness orporation, dass sich das erät ir2-s100 in Übereinstimmung mit den grundlegenden nforderungen und den übrigen einschlägigen estimmungen der Richtlinie 1999/5/ befindet. Български: С настоящето Ness orporation декларира, че ir2-s100 отговаря на съществените изисквания и другите приложими изисквания на Директива 1999/5/ЕС. Ελληνικά: Ο εξοπλισμός αυτός συμμορφώνεται με την Ευρωπαική Οδηγία 1999/ 5/ΕΚ spañol: Por la presente, el Ness orporation declara que este "producto" cumple con la requisitos esenciales y otras disposiciones relevantes de la irectiva 1999/ 5/. rançais: Par la présente, Ness orporation déclare que l appareil ir2-s100 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/. ansk: Undertegnede Ness orporation erklærer herved, at følgende udstyr ir2- S100 overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/. Magyar: z a berendezés megfelel az európai 1999/5/ irányelvnek. Malti: awnhekk, Ness orporation, jiddikjara li dan ir2-s100 jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fi d-irrettiva 1999/5/. Islenska: ér með lýsir Ness orporation yfi r því að ir2-s100 er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/. Italiano: on la presente, INess orporation. dichiara che questo ir2-s100 è con-forme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/. Lietuvių: Šiuo Ness orporation. deklaruoja, kad šis ir2-s100 atitinka esminius reikalavimus ir kitas 1999/5/ irektyvos nuostatas. nglish: ereby, Ness orporation, declares that this ir2-s100 is in compliance with the essential requirements and other relevant provisions of irective 1999/5/. Nederlands: ierbij verklaart Ness orporation dat het toestel ir2-s100 in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/. Norsk: Ness orporation erklærer herved at utstyret ir2-s100 er i samsvar med de grunnleggende krav og øvrige relevante krav I direktiv 1999/5/. Polski: Niniejszym Ness orporation deklaruje że ir2-s100 jest zgodny z zasadniczymi wymaganiami i innymi właściwymi postanowieniami yrektywy 1999/5/. Português: u, Ness orporation, declaro que o ir2-s100 cumpre os requisitos essenciais e outras provisões relevantes da irectiva 1999/5/. Româna: Prin prezenta, Ness orporation, declară că aparatul ir2-s100 este în conformitate cu cerinţele esenţiale şi cu alte prevederi pertinente ale irectivei 1999/5/. Svenska: enna utrustning är i överensstämmelse med de väsentliga kraven och andra relevanta bestämmelser i irektiv örsäkran om över 1999/5/. Slovenski: INess orporation izjavlja, da je ta ir2-s100 v skladu z bistvenimi zahtevami in drugimi relevantnimi določili direktive 1999/5/S. ir2-s100 declaration of conformity 17

18 Wireless accessories ppendix ORR OS Please quote the following Wireless Products order codes when ordering items from the Ness SmartLiving: ode Product description ir2-s100/10 Wireless transceiver module, 10 terminals ir2-s100/50 Wireless transceiver module, 50 terminals ir2-100 Wireless smoke detector ir2-ir100 Wireless PIR with 12m coverage ir2-ir100/ Wireless PIR with 20m coverage ir2-k100 4 button remote-control keyfob ir2-m100 Wireless magnetic contact with 2 inputs/outputs, in white ir2-m200 Two-way wireless magnetic contact, in white SmartLiving10100L SmartLiving1050L SmartLiving SmartLiving515 Intrusion control panel: manages 10 to 100 terminals, 15 partitions, switching power optional TP/IP connectivity, comes in metal enclosure with housing for 1 Intrusion control panel: manages 10 to 50 terminals, 10 partitions, switching power optional TP/IP connectivity, comes in metal enclosure with housing for 1 Intrusion control panel: manages 5 terminals, 5 partitions, switching power 1.2, comes in metal enclosure with housing for 1 Intrusion control panel: manages 5 to 10 terminals, 5 partitions, switching power comes in metal enclosure with housing for 1 18 Order odes

19 N N N T014 T014 National ustomer Service entre Ph: customerservice@ness.com.au IR2 Installation & Programming Manual ocument Part Number: ll possible care and diligence has been applied during manufacture to ensure the reliable operation of this product. owever there are various external factors that may impede or restrict the operation of this product in accordance with the product s specification. These factors include, but are not limited to: 1. rratic or reduced radio range. IR2 radio products are sophisticated low power devices, however the presence of in-band radio signals, high power transmissions or interference caused by electrical appliances such as wireless routers, cordless phones, computers, TVs and other electronic devices may reduce the range performance. While such occurrences are unusual, they are possible. In this case it may be necessary to either increase the physical separation between the IR2 receiver and other devices or if possible change the radio frequency or channel of the other devices. 2. Unauthorised tampering, physical damage, electrical interruptions such as mains failure, electrical spikes or lightning. ll rights reserved. No part of this publication may be reproduced, transmitted or stored in a retrieval system in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Ness. Ness reserves the right to make changes to features and specifications at any time without prior notification in the interest of ongoing product development and improvement Ness orporation Pty Ltd N

20 Innovative lectronic Solutions