Personal Security Pager. Instructions for use

Transcription

1 Personal Security Pager EN Instructions for use Personal Security Pager

2

3 Personal Security Pager Instruction for use EN 3 Table of contents 1. Introduction Use Main features Icon set Use the PS-Pager ON, OFF and configuration PS-Pager storage and recharge Read and delete messages Alarm Make an alarm Reset the alarm Remote switch off Signals and call types Attention signals Receiving call signals Setting the PS-Pager Set the volume and vibration Reverse the top display User interface Declaration Declaration of conformity... 15

4 Personal Security Pager Instruction for use EN 4

5 Personal Security Pager Instructions for use EN 5 1 Introduction 1.1 Use The Personal Security pager (PS-Pager) uses the Bosch PS6000 or DP6000 systems to provide personal security to people who work in potentially dangerous locations. The user can generate an alarm that the system acknowledges and the system can send messages to the user that the PS-Pager acknowledges. The PS-Pager is compatible with all Bosch PS6000 and DP6000 personal security and paging systems. 1.2 Main features The PS-Pager provides these main features: Send alarm call. Two manual alarm calls are available for the user. The PS-Pager is secured by self-monitoring and system scanning. Receive and handle text messages. Receive speech messages. Location detection. F G K E I J A B D C Made in The Netherlands H L Icon Name Icon Name A - D Soft keys I Manual alarm button (red) E Graphical front display J Reset button (black) F LED, red and green K Loudspeaker behind the clip G Safety clip L Top display, reversible H Battery recharge contacts

6 Personal Security Pager Instructions for use EN Icon set Icon Name Description Envelope Go to the message menu. Delete OK Menu Up Down Return Battery low The selected message can be deleted. The user confirms a command or setting. The user can navigate around the menu items. The user can navigate around messages and settings. The user can navigate around messages and settings. Return to a previous menu. The battery is low. The PS-Pager must be placed in a battery charger. * Telemetry The * shows that the message is a telemetry message Message No. The number before the message shows the order that a message is received.... Ellipsis The display is not large enough to show the complete message. Out of range The PS-Pager is out of range for the system.

7 Personal Security Pager Instructions for use EN 7 2 Use the PS-Pager Note If a key is not pressed within 8 seconds, the display goes to the standby display. Disclaimer Certain user options can be set by the installer and may not be present on your PS-Pager. 2.1 ON, OFF and configuration Turn the PS-Pager ON Note To turn the PS-Pager on or off, it must be in a system. To start the PS-Pager if the PS-Pager is off, do as follows: 1 Press the soft key D. 2 The PS-Pager shows on the display "Power on?". 3 Press OK to confirm Turn the PS-Pager OFF 1 Select Menu 2 Select Power off? and View configuration The user can view the current configuration of the PS- Pager. You can view the addresses, the user name and the Opcodes that are set. 1 Select Menu. 2 Select Settings and 3 Select View Config and 4 View the configuration data. Go back through the menu items. 2.2 PS-Pager storage and recharge Low battery indication When the PS-Pager has a low battery the PS-Pager: shows the low battery icon, emits the low battery warning bleep pattern, the LED flashes, shows the message low battery. The PS-Pager continues to work for a minimum of 30 minutes. Before the PS-Pager turns off it sends a last call to the central and gives a shutdown bleep Recharge the battery The time to recharge the internal battery is a maximum of four hours. The LED on the PS-Pager is red when the battery is being charged and green when the battery is full. To recharge: 1 Put the PS-Pager in a rack. 2 Wait until the LED is green. 3 The PS-Pager is ready for use. Note Any message received by the PS-Pager or any use of the menu when it is in a low battery state replaces low battery warning on the display. The low battery icon is present until the battery is recharged.

8 Personal Security Pager Instructions for use EN Charge rack and storage rack There are two types of rack available: storage rack and charge rack. The system administrator can set a rack to charge or storage. Whilst the PS-Pager is in the storage rack, it is absent from the system and is not available for any calls. The user name shows on the top display and the user name and the address shows on the front display. If a message is received whilst the PS-Pager is in the storage rack, it will give two attention bleeps when it is removed from the rack. The messages are shown in the memory stack. The PS-Pager is charged when it is in the storage rack. Whilst the PS-Pager is in the charge rack, it is present in the system and responds to all calls. 2.3 Read and delete messages Standby When the PS-Pager is at Stand-by mode, the display shows either the last message or the user information View a message The last ten messages sent to the PS-Pager are stored in the memory. If the last message received is already in the memory, the message moves to the top of the list. To read the other messages do as follows: Delete one message 1 Select Envelope. 2 Select the message and 3 Select the delete icon to delete the message and The message Message deleted! shows. 4 Go back to the message list Delete all messages If enabled by the installer, all the messages in the PS- Pager are deleted when it is put in the storage rack or when it is turned off Auto-scroll top display The top display will always auto-scroll if the message is more that 12 characters long Auto-scroll the front display If enabled by the installer, the front display can auto scroll when a message is received. The installer can also set the number of lines that can be viewed to either 2 or 4 lines. The auto scroll function is active for 30 seconds. 1 Select Envelope. 2 Select the message and 3 Go back to the message list. Note When the message is too long for the display, the message will auto scroll for a period of 30 seconds.

9 Personal Security Pager Instructions for use EN 9 3 Alarm 3.1 Make an alarm Manual alarm button The manual alarm button has the highest priority of all processes in the PS-Pager. The PS-Pager has two manual alarms: alarm 1 and alarm To start the alarm 1 Press the manual alarm button for at least one second. The PS-Pager gives a repeating audible bleep pattern of Alarm 1 and transmits it to the central To start the alarm 2 Press the manual alarm button for two short clicks within 2 seconds. The PS-Pager gives a continuous audible bleep of Alarm 2 and transmits it to the central. Alarm 2 is set by the installer of the PS-Pager. The alarm calls are repeated every 10 seconds until an acknowledgement from the central is received by the PS-Pager. Note The PS-Pager can be set to give a silent alarm. The PS-Pager will not then give an audible bleep. 3.2 Reset the alarm Stop the alarm sound Push the reset button to stop the audible alarm bleep. The alarm status will stay valid and new received locations will be sent to the central. The PS-Pager gives an audible attention bleep every minute and a LED flash to remind the user that the alarm status is still active. To clear the alarm the user has 2 options: reset by the central remote reset Reset by the central The central sends a call to the PS-Pager to alert the user to reset the alarm. To reset the alarm press the reset button one more time to accept the alert. The central resets the alarm Remote reset With an unmanned central, put the PS-Pager in storage rack to reset the alarm. 3.3 Remote switch off The central can switch off the PS-Pager during an alarm situation. During this period, all new received locations are still sent to the central Alarm 1 and 2 During an alarm the PS-Pager sends all new locations to the central. When the alarm is activated, the PS-Pager gives these bleeps and LED signals as follows: The alarm 1 sent to the central. The alarm 2 sent to the central. You can change alarm 1 to alarm 2, and alarm 2 to alarm1.

10 Personal Security Pager Instructions for use EN 10 4 Signals and call types 4.1 Attention signals Attention bleep - one bleep The PS-Pagers gives a bleep, shows "Waiting for central..." in the display and sends a handshake call to the central under these conditions: The PS-Pager goes from off to on and on to off. The PS-Pager put into the storage rack. The PS-Pager is removed from the storage rack. If a message came in while the PS-Pager was in the rack, an extra bleep is heard. An attention bleep only sounds under these conditions: The user deletes a message from the message list. The user passes certain location beacons. The PS-Pager is back in range of the system. The attention bleep pattern is as follows: Out of range detection - two bleeps The out of range signal tells the user that the PS-Pager is out of range of the system transmitters. The out of range signal is two short bleeps followed by a silence. The PS- Pager repeats the signal for 68 seconds, until the PS- Pager is back in range or the user pushes the reset button. 30 Minutes after the first bleep pattern, the PS- Pager gives a shutdown bleep and turns off. The out of range bleep pattern is as follows: User action: Return the PS-Pager into the range. An attention bleep will sound when it is back in range Low battery - three bleeps Indicates the PS-Pager has a low battery. Refer to Recharge the battery. The low battery bleep pattern is as follows: Central not responding - continuous bleep pattern The central must acknowledge a handshake call. If the central does not acknowledge the handshake call, after 30 seconds the PS-Pager starts a continuous bleep pattern and shows "Central not responding" on the display. If the PS-Pager has the message Central not responding in the display do as follows: the PS-Pager goes from OFF to ON, press the reset button. The PS-Pager goes to OFF. Report the action to the system administrator the PS-Pager goes from ON to OFF, the mobile can not be turned off. Report the action to the system administrator the PS-Pager is put into a rack, remove the PS-Pager from the rack and put back in. Report the action to the system administrator the PS-Pager is removed from the rack, put the PSpager back in the rack. Report the action to the system administrator Error - four bleeps The PS-Pager gives indication that there is an internal error. Put the PS-Pager back in the rack. If it still does not function, report to the system administrator. The error bleep pattern is as follows: Shutdown bleep - one long bleep If the PS-Pager is out of range for 30 minutes or if it has a low battery, the shut down bleep sounds. Before the PS-Pager switches off, it sends a last call to the central, gives the shutdown bleep and then turns off. The shutdown bleep also sounds when the PS-Pager is turned off. The shut down bleep pattern is as follows:

11 Personal Security Pager Instructions for use EN Special location bleep When a special location beacon is passed, the PS-Pager give a bleep pattern. This bleep pattern can be one of the following: Attention bleep. Location signal. Bleep until reset. Press the reset button on the PS-Pager. Location signal. Bleep until put in rack. Place the PS- Pager in a storage rack. Special location attention signal Special location signal. 4.2 Receiving call signals The PS-Pager can make 7 different bleep patterns in normal and cricketed bleeps. The 7 normal bleep patterns are used to produce individual calls; group calls always produce cricketed tones. The LED flashes for a longer time than the bleep pattern sounds. If the vibrator is set, it will give a signal in the same pattern as the bleep pattern. The LED flashes for another 8 seconds Individual calls The central can always make an individual call to a PS- Pager. If the PS-Pager is in the storage rack then it sends an absent signal to the central Group calls A group call always has a cricketed bleep. PS-Pagers that are in a storage rack will not respond and do not send an absent indication to the central. Examples of groups are rescue teams and cardiac arrest teams All call If enabled by the installer the central can send a call to all the compatible receivers in the system. The all call address is the same for all PS-Pagers in the system and all will respond Serial group calls A serial group call addresses PS-Pagers one-by-one. With a serial group call absent conversions are possible Telemetry calls If enabled by the installer the user can be sent up-todate information, e.g. process control and temperature. When the telemetry function is enabled, a * in front of the message when in the memory, shows that the message is a telemetry call. A telemetry call is always the first message in the list and will be overwritten when a new telemerty calls is received. 0/8 1/9 2/A 3/B 4/C 5/D 6/E 7/F Note If the PS-Pager receives a call when it is in silent mode, it will always give a vibration. Silent call 4 seconds Bleep patterns 0-6 = normal patterns Bleep patterns 8 - E = cricketed patterns Speech calls If enabled by the installer the PS-Pager can receive spoken messages. The speech message ends when the speech time is exceeded or when the user presses the reset button. The speech call resumes if the user presses the reset button again within 8 seconds.

12 Personal Security Pager Instructions for use EN 12 5 Setting the PS-Pager Dependant on the installation configuration of the PS- Pager, you are able to change the user parameters as follows: Volume of the bleep Vibration on or off Speech volume Top display reversal 5.1 Set the volume and vibration Set the volume of the bleep The PS-Pager has four bleep options: silent, soft, normal and loud. To select the volume of the bleep do as follows: 1 Select Menu. 2 Select Settings and 3 Select Bleep and press OK to confirm. 4 Select the required volume and press OK to confirm. The display confirms the new bleep volume Set the vibration on or off The PS-Pager has two options: vibration on and off. If the vibrator is set, it will give a signal in the same pattern as the bleep pattern. To select the vibration mode do as follows: 1 Select Menu Set the speech volume The PS-Pager has two options: soft and loud. To select the speech volume do as follows: 1 Select Menu. 2 Select Settings and 3 Select Speech and 4 Select the required volume and press OK to confirm. The display confirms the new speech volume 5.2 Reverse the top display Reverse the view of the top display The user can reverse the top display to view the display for example when the PS-Pager is in a breast pocket. To set the PS-Pager do as follows: 1 Select Menu. 2 Select Settings and 3 Select Top Display and 4 Select the Clip view or Front view and press OK to confirm. The display confirms the new top display setting. 2 Select Settings and 3 Select Vibration and 4 Select On or Off and The display confirms the new vibration.

13 Personal Security Pager Instructions for use EN User interface PS-Pager ON? Power off? OFF Settings Bleep Silent Bleep silent! Soft Bleep soft! Normal Bleep normal! Loud Bleep loud! Vibration On Vibration on! Off Vibration off! Speech Soft Speech soft! Loud Speech loud! Top display Front View Front view! Clip View Clip view! View Config 7 Addr & 3 Opc 1 Message 1 Delete message Message deleted! 2 Message 2 Delete message Message deleted! 3... Delete message Message deleted! 10 Message 10 Delete message Message deleted!

14 Personal Security Pager Instructions for use EN 14 6 Declaration English Finnish Dutch French Swedish Danish German (BMWi) German (Wien) Italian Greek Italian Spanish Portugese Malti Estonian Hungarian Slovak Czech Slovene Lithuanian Latvian Hereby, Bosch Security Systems B.V., declares that this PS2-B is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Bosch Security Systems B.V. vakuuttaa täten että PS2-B tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Hierbij verklaart Bosch Security Systems B.V. dat het toestel PS2-B in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Bij deze verklaart Bosch Security Systems B.V. dat deze PS2-B voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC. Par la présente Bosch Security Systems B.V. déclare que l'appareil PS2-B est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Par la présente, Bosch Security Systems B.V. déclare que ce PS2-B est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables. Härmed intygar Bosch Security Systems B.V. att denna PS2-B står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Undertegnede Bosch Security Systems B.V. erklærer herved, at følgende udstyr PS2-B overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Hiermit erklärt Bosch Security Systems B.V., dass sich dieser/diese/dieses PS2-B in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/ EG befindet". Hiermit erklärt Bosch Security Systems B.V. die Übereinstimmung des Gerätes PS2-B mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. Con la presente Bosch Security Systems B.V. dichiara che questo PS2-B conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Bosch Security Systems B.V. ΗΛΩΝΕΙ ΟΤΙ PS2-B ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΙΑΤΑΞΕΙΣ ΤΗΣ Ο ΗΓΙΑΣ 1999/5/ΕΚ Con la presente Bosch Security Systems B.V. dichiara che questo PS2-B conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Por medio de la presente Bosch Security Systems B.V. declara que el PS2-B cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Bosch Security Systems B.V. declara que este PS2-B está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Hawnhekk, Bosch Security Systems B.V., jiddikjara li dan PS2-B jikkonforma maltiijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-dirrettiva 1999/5/EC. Käesolevaga kinnitab Bosch Security Systems B.V. seadme PS2-B vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. Alulírott, Bosch Security Systems B.V. nyilatkozom, hogy a PS2-B megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Bosch Security Systems B.V. týmto vyhlasuje, že PS2-B splna základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Bosch Security Systems B.V. tímto prohlašuje, že tento PS2-B je ve shode se základními požadavky a dalšími príslušnými ustanoveními smernice 1999/5/ES. Šiuo Bosch Security Systems B.V. deklaruoja, kad šis PS2-B atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Šiuo Bosch Security Systems B.V. deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Ar šo Bosch Security Systems B.V. deklare, ka PS2-B atbilst Direktivas 1999/5/EK butiskajam prasibam un citiem ar to saistitajiem noteikumiem.

15 Personal Security Pager Instructions for use EN 15 7 Declaration of conformity The Declaration of conformity is available on request.

16 For more information visit Bosch Security Systems B.V. Data subject to change without notice EN