SMART SMOKE DETECTOR

Transcription

1 SMART SMOKE DETECTOR 1. INTRODUCTION 2 2. PACKAGE CONTENTS 2 3. SPECIFICATIONS 3 4. CHOOSING A SUITABLE LOCATION FOR THE SMOKE DETECTORS 4 5. INSTALLATION AND ACTIVATION 5 6. ALARM SIGNALS AND VISUAL INDICATION 9 7. SERVICE LIFE AND FUNCTIONAL TEST FEDERAL COMMUNICATIONS COMMISSION STATEMENT LIMITED PRODUCT WARRANTY FAQ CONTACT DISTRIBUTOR 11

2 1. INTRODUCTION This smart smoke detector is a Z-Wave device (interoperable, with RF mesh network technology which works in two directions) and is compatible with every Z-Wave network and the related security framework. Each device driven by Z-wave functions as a signal amplifier, so that multiple devices ensure a greater number of transition routes, which help to eliminate "RF dead spots". Z-Wave devices with the Z-Wave logo can also be used for this, regardless of the manufacturer. Furthermore, our devices can also be used in Z-Wave networks of other manufacturers. 2. PACKAGE CONTENTS Smoke detector Mounting kit Battery Quick start guide 2

3 3. SPECIFICATIONS PRODUCT IDENTIFICATION Fifthplay Product ID DIMENSIONS Diameter Depth INTERFACES Test button Alarm volume POWER CONSUMPTION Battery power RF COMMUNICATION Protocol Frequency range CONTROL PARAMETERS Temperature 120 mm 5.3 mm 85dB from a 3m distance 3V Lithium Z-Wave (ZM5202N) MHz (ZS6101/6102EU-5) C Relative humidity 10 95% Action radius CURRENT STANDARD EN14604: CPR /01 Z-WAVE COMMAND CLASSES COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_BATTERY COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_NOTIFICATION_V4 COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_SECURITY COMMAND_CLASS_SWITCH_BINARY (for ZS6102 only) COMMAND_CLASS_VERSION_V2 COMMAND_CLASS_WAKE_UP (for ZS6101 only) COMMAND_CLASS_ZWAVEPLUS_INFO 30 m 3

4 4. CHOOSING A SUITABLE LOCATION FOR THE SMOKE DETECTORS DO DON T Install a smoke detector in every staircase, hallway, bedroom and living space for optimum safety. Mount the smoke detector in the centre of the ceiling as much as possible. If this is not possible, install the smoke detector at least 10 cm away from every wall or corner. If the installation on the ceiling is not possible, mount the smoke detector on the wall, at approximately 10 to 15 cm from the ceiling. Rooms in which strong water damp, dust or smoke arise under normal conditions. Close to fireplaces or open fires. Close to ventilation ducts where the air flow might prevent smoke to reach the smoke detector. Close to fluorescent or economy lamps. The starter of these lamps might cause a false alarm due to the electric fields. SMOKE DETECTORS FOR MINIMUM SAFETY SMOKE DETECTORS FOR OPTIMUM SAFETY SMOKE DETECTORS FOR MINIMUM SAFETY SMOKE DETECTORS FOR OPTIMUM SAFETY 4

5 5. INSTALLATION AND ACTIVATION INSTALLATION OF THE BATTERY A B 1. Remove the rear side (A) of the smoke detector by turning in a counter-clockwise motion. 2. Open the cover of the battery (B), place the battery, and close the cover again. 3. Place back the rear side of the smoke detector by turning in a clockwise motion. 4. After 8 to 12 seconds, the smoke detector will release a signal, indicating that the smoke detector is ready for connection to the gateway. 5

6 5.1.2 CONNECTING A SMOKE DETECTOR TO YOUR FIFTHPLAY CUBE C IMPORTANT: Ensure that the smoke detector is in the immediate vicinity (0.5 to 1 meter) of the gateway. You can connect your smoke detector to your fifthplay cube in the following 2 ways: Via the APP: 1. Open the fifthplay Home app and log in. 2. At the top left of the app, click on and select 'CONFIGURATION'. 3. Go to 'DEVICES'. 4. At the top right, click on Select 'SENSOR' as the type of device. 6. Select 'SMOKE DETECTOR'. 7. Wait until the gateway is in connection mode (Once the connection mode has been established, you will see a notification on your screen). If this is not the case, click on 'CANCEL' and 'TRY AGAIN'. Please note: If no devices to be added are found, the connection mode will automatically be terminated after 2 minutes. 8. Press 3x briefly (less than 1 second) on the program switch of the sensor (C) to set up the connection with the gateway. Once the connection has been established, you will see a confirmation message on your screen. Please note: If no device is found within 30 seconds, press the programming button (A) again. 9. Once the smoke detector has been added, you will see a notification on your screen. 10. If desired, change the name of the smoke detector. Via the WEBSITE: 1. Go to home.fifthplay.com and log in. 2. Go to 'CONFIGURATION'. 3. Go to 'DEVICES'. 4. Click on 'ADD A DEVICE'. 5. Click on 'ADD A SENSOR'. 6. Select 'SMOKE DETECTOR' and click on 'NEXT'. 7. Wait until the gateway is in connection mode (Once the connection mode has been established, you will see a notification on your screen). If this is not the case, click on 'CANCEL' and 'TRY AGAIN'. Please note: If no devices to be added are found, the connection mode will automatically be terminated after 2 minutes. 8. Press 3x briefly (less than 1 second) on the program switch of the sensor (C) to set up the connection with the gateway. Once the connection has been established, you will see a confirmation message on your screen. Please note: If no device is found within 30 seconds, press the programming button (A) again. 9. Once the smoke detector has been added, you will see a notification on your screen. 10. If desired, change the name of the smoke detector. 6

7 5.1.3 MOUNTING OF THE SMOKE DETECTOR A 1. Place the rear side (A) of the smoke detector where you want to install it. 2. Mark each hole for the screws to determine the location of the plugs and screws. 3. Use a 5 mm drill and drill 2 holes on the marked locations. 4. Place the plugs in the drill holes and secure the rear side (A) of the smoke detector in place by using the screws. 5. Mount the smoke detector on the rear side by turning in a clockwise motion. 6. If the smoke detector has been mounted correctly, the LED lamp of the smoke detector shall light up every 334 seconds. 7

8 5.1.4 DISCONNECTING A SMOKE DETECTOR FROM YOUR FIFTHPLAY CUBE C IMPORTANT: Ensure that the smoke detector is in the immediate vicinity (0.5 to 1 meter) of the gateway. You can disconnect your smoke detector from your fifthplay cube in the following 2 ways: Via the APP: 1. Open the fifthplay Home app. 2. At the top left of the app, click on and select 'CONFIGURATION'. 3. Go to 'DEVICES'. 4. Select the smoke detector you want to remove. 5. Click on 'REMOVE'. 6. Check that the gateway is in connection mode (Once the connection mode has been established, you will see a notification on your screen). If this is not the case, click on 'CANCEL' and 'TRY AGAIN'. Please note: If no devices to be removed are found, the connection mode will automatically be terminated after 2 minutes. 7. Press 3x briefly (less than 1 second) on the program switch of the sensor (C) to disconnect it from the gateway. 8. Once the smoke detector has been removed, you will see a notification on your screen. Via the WEBSITE: 1. Go to home.fifthplay.com and log in. 2. Go to 'CONFIGURATION'. 3. Go to 'DEVICES'. 4. Select the smoke detector you want to remove. 5. Click on 'REMOVE DEVICE'. 6. Wait until the gateway is in connection mode (Once the connection mode has been established, you will see a notification on your screen). If this is not the case, click on 'CANCEL' and 'TRY AGAIN'. Please note: If no devices to be removed are found, the connection mode will automatically be terminated after 2 minutes. 7. Press 3x briefly (less than 1 second) on the program switch of the sensor (C) to disconnect it from the gateway. 8. Once the smoke detector has been removed, you will see a notification on your screen. 8

9 6. ALARM SIGNALS AND VISUAL INDICATION STATUS ACTIVATION MODE (the battery is placed in the smoke sensor) SMOKE DETECTED IDLE MODE (the smoke detector is functioning properly) LOW BATTERY VOLTAGE DISMANTLING SECURITY (the smoke detector is not installed correctly) ERROR SIGNAL QUIET MODE INDICATION ON THE SMOKE DETECTOR WHAT YOU SEE WHAT YOU HEAR Orange LED flashes once 1 beep after 8 to 12 sec - Red LED flashing fast and continuously Red LED flashes once every 334 seconds Red and orange LED flash continuously Orange LED lights up continuously Orange LED flashes continuously 4 beeps / break / 4 beeps / beep every 43 seconds 4 beeps / break / 4 beeps / 3 beeps every 43 seconds - INDICATION IN THE APP Push notification / text message / Push notification / text message / Push notification / text message / The quiet mode can temporarily silence an alarm. To make use of this function, press the test button of the device when the alarm sounds. If the smoke concentration is still too high after 10 minutes, the alarm will sound again. 9

10 7. SERVICE LIFE AND FUNCTIONAL TEST It is recommended to replace smoke detectors 5 years after the production date. You can find this date on the device. The fifthplay smoke detector tests its battery capacity every 2 hours. If the capacity is less than 2.7V (+/-0.1V), a message is sent via the app and a visual and audible signal can be observed on the smoke detector itself (also see (5) Alarm signals and Visual Indication). Test the smoke detector on a weekly basis by holding down the test button until the alarm sounds (hold down for approximately 4 seconds). If the smoke detector is functioning properly, you will hear 3 beeps and the red LED lamp will flash fast and continuously. If the smoke detector only beeps once and the red LED lamp flashes only 3 times, the smoke detector is not functioning properly. If this is the case, it must be checked. 8. FEDERAL COMMUNICATIONS COMMISSION STATEMENT This product complies with all of the relevant European guidelines and regulations. If applicable, you can find the EC declaration of conformity regarding this product at com/downloads. This product cannot be deposited in the unsorted waste. Take your discarded product to a recycling centre or a recognised collection point. Just like producers and importers, you too play an important role in the promotion of sorting, recycling and reuse of waste electrical and electronic equipment. To finance the rubbish collection and waste treatment, the government levies recycling charges in certain cases (included in the price of this product). 9. LIMITED PRODUCT WARRANTY The warranty period is two years from the date of delivery. The delivery date is the invoice date of purchase of the product by the consumer. If there is no invoice, the date of production applies. The consumer is obliged to inform fifthplay in writing about the non-conformity, within two months of noticing the defect. In case of a non-conformity, the consumer only has the right to a product repair or replacement free of charge, which shall be decided by fifthplay. fifthplay shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance instructions or an external cause, such as damage due to moisture or overvoltage. The compulsory regulations of the national legislation concerning the sale of consumer goods and the protection of the consumer in the countries where fifthplay sells, directly or via sister companies, subsidiaries, chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned rules and regulations. 10

11 10. FAQ Consult our frequently asked questions page on cube.fifthplay.com/faq or consult the user manuals on cube.fifthplay.com/downloads 11. CONTACT Telephone: +32 (0) DISTRIBUTOR Fifthplay NV Generaal Lemanstraat, 47 B-2018 Antwerp 11