Addendum # 1 to Bid MEB Audiovisual Faculty Training Center Renovation
|
|
- Sherman Morgan
- 5 years ago
- Views:
Transcription
1 Date 1/14/19 Addendum # 1 to Bid 2235 MEB Audiovisual Faculty Training Center Renovation Change the above referenced Invitation to Bid to agree with this addendum. LSU Health Sciences Center will reject any proposal which does not acknowledge this addendum. Acknowledge by including a signed copy of this addendum with your bid. Prior Approvals: See attached approved substitute for lighting from LSI Industries. Bid Questions: Q. On E21 note 6. Is the existing 15 amp breaker to feed new panel LC3B located in DL3C? If not, need panel location to get feeder length A. Yes, the existing 15A/3P circuit breaker (in existing Panel DL3C) that was previously feeding removed Panel LC3B is to be used to serve the new Panel LC3B as indicated in Specific Note 6. Existing Panel DL3C is located in the same room as the new location for Panel LC3B. Q. On E11 floor box symbol shows 3-1 1/4" conduits for data, on A22 note 8 shows 2-2" conduits for data. Which is correct? A. The floor box shall contain be roughed in with three 1 ¼ raceways in lieu of two 2 raceways. This was previously confirmed with LSU AV Department on October 24, 218. Q. Sheet A23 partition type 4 calls for 2 layers of 5/8 drywall on both sides, drawing shows 2 layers 1 side. Which is correct? A. 2 layers one side Q. Partition type 4A calls for 2 layers of 5/8 drywall on both sides, drawing shows 1 layer 1 side. Which is correct? A. 1 layer 1 side Q. Also note the following corrections of copy over notes: Partition 1A & 2A calls for 2 layers of 5/8 drywall both sides, drawing shows 1 layer both sides. A. Yes, 1 layer both sides is correct. Michael D. Williams Purchasing By Name/Title (Signature) (Type or Print) Firm s Name
2 Date: Dec 21, 218 Bell & McCoy Lighting and Controls 3527 Ridgelake Drive Metairie LA 72 Phone: (54) Fax: (54) Job Name Bid Date Dec 21, 218 Submittal Date Dec 21, 218 Architect: MATHES BRIERRE 21 ST. CHARLES AVE, #41 NEW ORLEANS LA 717 Engineer: GVA ENGINEERS-METAIRIE 2615 EDENBORN AVE # C METAIRIE LA 72
3 FF9 Put our team to work for you! Page 1/1 Date: Dec 21, 218 Page 1/1 Transmittal Bell & McCoy Lighting and Controls 3527 Ridgelake Drive Metairie LA 72 Phone: (54) From: CHARLES KLEINSCHMIDT Project Quote# Location To LSU HEALTH SCIENCES CENTER - PURCHASING 433 BOLIVAR ST FLOOR 6 NEW ORLEANS LA 7112 Contact: ATTACHED WE ARE SENDING YOU 1 COPY OF THE FOLLOWING ITEM: Drawings Specifications Other: Prints Information Plans Submittals THESE ARE TRANSMITTED FOR: X Prior Approval Resubmittal for Approval Record Approval Corrections Bids due on: Approval as Submitted Your Use Other: Approval as Noted Review and Comment Type MFG Part F1 LSI LPEC24 LED 48L UNV DIM1 35 F2 LSI LPEC22 LED 45L UNV DIM1 35 F3 LSI LPEC24 LED 55L UNV DIM1 35 EX LSI EXC R U WB XXX SD2
4 FF1 Put our team to work for you! Page 1/1 Dec 21, 218 LSU HEALTH SCIENCES CENTER - PURCHASING 433 BOLIVAR ST FLOOR 6 NEW ORLEANS LA 7112 RE: Type MFG Part F1 LSI LPEC24 LED 48L UNV DIM1 35 F2 LSI LPEC22 LED 45L UNV DIM1 35 F3 LSI LPEC24 LED 55L UNV DIM1 35 EX LSI EXC R U WB XXX SD2
5 1/4 LPEC24 LED 48L UNV DIM1 35 F1 Catalog # : Project : Prepared By : Date : Type : LPEC 2 x4 The LPEC s low profile design makes it ideal for shallow plenum applications. Best in class configurable lumen packages and efficiencies that target DLC Standard/ Premium. This fixture delivers even illumination with excellent, low angle brightness control throughout the space. Available in 1x4, 2x2, and 2x4. Features & Specifications Optical System High transmission impact resistant diffuse acrylic radius lens eliminates bright spots from individual LED s and provides high vertical illumination and visual comfort. Use of closely spaced medium-power, high brightness chips minimizes pixelation and provides uniform lens luminance. Available in 5K, 4K, 35K and 3K color temperatures. Minimum CRI of 8. Optional 9 CRI available, consult factory for lead times. Electrical High-performance driver features over-voltage, under voltage, short-circuit and over temperature protection. -1 volt dimming (1% - 1%) standard. Standard Universal voltage ( Vac) Input 5/6 Hz or optional High voltage (347Vac). L7 Calculated Life: >1k Hours (See Lumen Maintenance on Page 2) Total harmonic distortion: <2% Power factor: >.95 Input power stays constant over life. Optional 12v-277v integral emergency battery pack is available to meet critical life-safety lighting requirements. The 9-minute batteries provide constant power to the LED system, ensuring code compliance. A test switch/indicator button is installed in the housing for ease of maintenance. Controls LSI AirLink controls featuring Lutron Clear Connect makes each luminaire controllable, creating a wireless communication with other AirLink control devices such as dimmers, switches, occupancy sensors and photocontrols. The integrated sensor is both a passive infrared motion detector and photocell. See Page 2 for coverage diagram. Step-level dimming option allows system to be switched to 5% power for compliance with common energy codes while maintaining fixture appearance. Sensor Ready Drivers available; consult factory for limitations. Dimensions 5.36" (136mm) 4.815" (122mm) " (65mm) 1.5" (38mm) (AirLink Power Pack).545" 13.84mm) (AirLink Occupancy Sensor) 2.95" (74mm) 1.382" (35mm) 6.212" (158mm) 5.266" (134mm) (.875"K.O.) 2.95" (74mm) " (1212mm) 8.9" (25mm).547" (13.89mm) SIDE VIEW 8.31" (211mm) 2.516" (64mm) ARRA Funding Compliant " (1212mm) Optional AirLink Occupancy Sensor TOP VIEW " (1212mm) Acceess Plate Location Optional AirLink Power Pack BACK VIEW " (65mm) END VIEW 3.628" (92mm) " (65mm) LSI Industries Inc. 1 Alliance Rd. Cincinnati, OH (513) LSI Industries Inc. All Rights Reserved.
6 2/4 LPEC24 LED 48L UNV DIM1 35 F1 LPEC 2 x4 Features & Specifications (Cont.) Performance Construction Rigid housing is die-formed 2-gauge cold rolled steel for consistency and strength. End plates come equipped with integral NEC compliant earthquake clips. Ultra-slim < 3 luminaire height and lightweight design effectively target a broad range of plenum/wall spaces and allow for easy installations. Below plenum room side access to optical chamber and driver compartment via pressure removable radius lens and side panel. Luminaire is proudly manufactured in the U.S. Luminaire is painted after fabrication following treatment with phosphate rust inhibitor. Finish coating of housing reflecting surfaces is with highreflectance white (minimum 92%) polyester powder. Installation Luminaire installs by lifting it through grid ceiling and resting it on the T-bars. Luminaire installs onto standard 15/16 and narrow 9/16 T-grid ceiling systems. An accessory flange kit is available for installing into drywall or plaster. Warranty LSI LED Fixtures carry a 5-year warranty. 1 Year warranty on optional Battery Back Up. Test regularly in accordance with local codes. Listings Listed to UL 1598 and UL 875 for 25 C Ambient applications. IC Rated. DesignLights Consortium (DLC) Premium and/or standard qualified product. Not all versions of this product may be DLC qualified. Please check the DLC Qualified Products List at to confirm which versions are qualified. RoHS Compliant. American Recovery and Reinvestment Act Funding Compliant. Lighting Facts Approved. Suitable For Damp Locations. DELIVERED LUMENS* 3K 35K 4K 5K Efficacy Efficacy *LED Chips are frequently updated therefore values are nominal. Efficacy ELECTRICAL DATA* Watts 12V 28V 24V 277V 347V 3L L L L L L L L L L L *Electrical data at 25C (77F). Actual wattage may differ by +/-1%. Efficacy Wattage 3L L L L L L L L L L L RECOMMENDED LUMEN MAINTENANCE 1 Ambient Temp C hrs. 2 25K hrs. 2 5K hrs. 3 75K hrs. 3 1K hrs % 95.14% 92.57% 9.7% 87.64% 1 - Lumen maintenance values at 25 C are calculated per TM-21 based on LM-8 data and in-situ luminaire testing. 2 - In accordance with IESNA TM-21-11, Projected Values represent interpolated value based on time durations that are within six times (6X)the IESNA LM-8-8 total test duration (in hours) for the device under testing ((DUT) i.e. the packaged LED chip). 3 - In accordance with IESNA TM-21-11, Calculated Values represent time durations that exceed six times NA LM-8-8 total test duration (in hours) for the device under testing ((DUT) i.e. the packaged LED chip). APPLICATION REFERENCE* Spacing LPW W/FT2 Avg Fc # of Luminaires 48L 12' x 1' L 1' x 8' L 1'x 6' *Based on a 9' Mtg.Ht., 4K color Temp, 8/5/2 reflectances, 2.5' work plane, LLF:1., 4' x 4' Room LSI Industries Inc. 1 Alliance Rd. Cincinnati, OH (513) LSI Industries Inc. All Rights Reserved. 1/2/17
7 3/4 LPEC24 LED 48L UNV DIM1 35 F1 LPEC 2 x4 Luminaire Ordering Guide TYPICAL ORDER EXAMPLE: LPEC24 LED 48L UNV DIM1 4 ALC EM U Family/Size LED Gen LPEC24 - (2x4) LED 3L L L L L L L L L L L - 9 *Consult factory for programmable wattages and lumen packages. Lumen Package* Voltage Driver UNV V HV - 347V 1 DIM1 - Dims to 1% (-1 volt dimming) LDE1 - Hi-Lume 1% 4 (With Soft On Fade To Black) L3D -Lutron Hi-Lume 1% 4 LDE5 - Lutron 5-Series 4 SR - Sensor Ready 4 SD5 Step Dimming Driver to 5% Color Temperature Controls Options Packaging 3-3K 3,4 BLANK - (No Controls) EM1-1 watt Emergency U - Single Pack 35-35K Battery Backup JP - Job Pack 4-4K ALC - AirLink Controller 5-5K FC1-6 3/8 (3) #18 Leads ALOS - AirLink Controller w/ (For Use In Non-Dimming Occupancy Sensor Applications) ALVS - AirLink Controller w/ Vacancy Sensor FC15D - 6 3/8 (5) #18 Leads (For Use In Dimming Applications 9C - 9 CRI 3,4 Accessory Ordering Information (Accessories are field installed) Description Order Number Flange Kit 2x4 FK24 AirLink Control Accessories Wireless switches Catalog number Part Number Wireless Occupancy Sensors Part Number On/Off & Raise Lower ALWS 3B-(color)-KIT Wireless 36 4 ft², Ceiling Mount Wireless 18 3 ft², Wall Mount Wireless Photocell controls Catalog number Part Number Wireless 9 25 ft², Corner Mount On/Off & Dimming ALCM-W-PC 6249 Wireless, Hallway 15 ft Length Commission Laser Kit (See Laser warnings) Order as separate catalog number. Visit for complete listing of AirLink controls. Footnotes: 1 - Not available with AirLink 2 - Available colors are White, Ivory and Light Almond (WH, IV, LA) 3 - Consult Factory for lead times 4 - Consult with factory Photometry LPEC24 LED 48L 4 Luminaire photometry has been conducted by a NVLAP accredited testing laboratory in accordance with IESNA LM As specified by IESNA LM-79-8 the entire luminaire is tested as the source resulting in a luminaire efficiency of 1%. See for detailed photometric data ZONAL LUMEN SUMMARY ZONE LUMENS , , , , , , , , , , ,848.5 % OF LUMINAIRE LSI Industries Inc. 1 Alliance Rd. Cincinnati, OH (513) LSI Industries Inc. All Rights Reserved.
8 4/4 LPEC24 LED 48L UNV DIM1 35 F1 LPEC 2 x4 Controls enabled by Lutron AirLink is LSI s wireless indoor lighting control system. This fixture is compatible with the AirLink system & contains a factory-installed fixture controller (ALC) & sensor (ALOS/ALVS). For further information on these components, you can view their specsheets at Range Wireless Sensors & Controls must be located within 6ft (18m) line of sight or 3ft (9m) through walls of the associated control module Major motion: Movement of a person entering or passing through an area Minor motion: Movement of a person occupying an area and engaging in small activities (e.g., reaching for a telephone, turning the pages of a book, etc.) Ceiling Applications Small offices, conference rooms, lounges, classrooms Features Floor Minimum Light Level Setting (optional). Certain applications, such as hallways, may require that the lights never turn off. For these areas, select the minimum light level option and the load will lower to programed low-end level Daylighting dims lights down to OFF. Occupancy sensor must go unoccupied (vacant) in order for the fixture sensor to turn the lights off Occupancy sensor timeout (fixture sensor): 15 minutes Power failure memory: If power is interrupted, connected loads will return to the previous level Low-end trim adjustment (default is 1V or ballasts/drivers minimum for Lutron EcoSystem ballasts/drivers). High-end trim adjustment (default is 1V or 1% for Lutron EcoSystem ballasts/drivers) Includes integrated power measurement circuit that provides data to the wireless hub with +/_ 2% accuracy or.5w whichever is higher Passive infrared motion detection with exclusive Lutron XCT Technology for major and minor motion detection Up to 3 ft 2 (27.9 m 2 ) major motion coverage and 15 ft 2 (13.9 m 2 ) minor motion coverage & 36 field-of-view Daylight sensor has simple, automatic calibration straight out-of-the-box Designed to give a linear response to changes in perceived light level. Detects ambient light level changes from to 15 fc ( to 16 lx) 9.8ft (3m) 6.8ft (2.1m) 3ft 2 (28m 2 ) major motion 15ft 2 (14m 2 ) minor motion when mounted on a ceiling LSI Industries Inc. 1 Alliance Rd. Cincinnati, OH (513) LSI Industries Inc. All Rights Reserved. 1/2/17
9 1/4. LPEC22 LED 45L UNV DIM1 35 F2 Catalog # : Project : Prepared By : Date : Type : LPEC 2 x2 The LPEC s low profile design makes it ideal for shallow plenum applications. Best in class configurable lumen packages and efficiencies that target DLC Standard/ Premium. This fixture delivers even illumination with excellent, low angle brightness control throughout the space. Available in 1x4, 2x2, and 2x4. Features & Specifications Optical System High transmission impact resistant diffuse acrylic radius lens eliminates bright spots from individual LED s and provides high vertical illumination and visual comfort. Use of closely spaced medium-power, high brightness chips minimizes pixelation and provides uniform lens luminance. Available in 5K, 4K, 35K and 3K color temperatures. Minimum CRI of 8. Optional 9 CRI available, consult factory for lead times. Electrical High-performance driver features over-voltage, under voltage, short-circuit and over temperature protection. -1 volt dimming (1% - 1%) standard. Standard Universal voltage ( Vac) Input 5/6 Hz or optional High voltage (347Vac). L7 Calculated Life: >1k Hours (See Lumen Maintenance on Page 2) Total harmonic distortion: <2% Power factor: >.95 Input power stays constant over life. Optional 12v-277v integral emergency battery pack is available to meet critical life-safety lighting requirements. The 9-minute batteries provide constant power to the LED system, ensuring code compliance. A test switch/indicator button is installed in the housing for ease of maintenance. Dimensions 2.95" (74mm) " (62mm) Optional AirLink Power Pack 5.263" (134mm) BACK VIEW 8.159" (27mm) " (62mm) 2.512" (64mm) 6.61" (168mm) ARRA Funding Compliant SIDE VIEW Acceess Plate Location.875 K.O " (65mm) 7.626" (194mm) 4.45" (112mm) 1.375" (35mm) " (62mm) Optional AirLink Occupancy Sensor " (65mm) 1.375" (35mm) 3.631" TOP VIEW (92mm) Controls LSI AirLink controls featuring Lutron Clear Connect makes each luminaire controllable, creating a wireless communication with other AirLink control devices such as dimmers, switches, occupancy sensors and photocontrols. The integrated sensor is both a passive infrared motion detector and photocell. See Page 2 for coverage diagram. Step-level dimming option allows system to be switched to 5% power for compliance with common energy codes while maintaining fixture appearance. Sensor Ready Drivers available; consult factory for limitations. 2.95" (74mm) " (65mm) " (658mm) END VIEW 1.5" (38mm) (AirLink Power Pack) Attached via 9 degree Elbow Bracket through.875 K.O..545" 13.84mm) (AirLink Occupancy Sensor) LSI Industries Inc. 1 Alliance Rd. Cincinnati, OH (513) LSI Industries Inc. All Rights Reserved.
10 2/4 LPEC22 LED 45L UNV DIM1 35 F2 LPEC 2 x2 Features & Specifications (Cont.) Construction Rigid housing is die-formed 2-gauge cold rolled steel for consistency and strength. End plates come equipped with integral NEC compliant earthquake clips. Ultra-slim < 3 luminaire height and lightweight design effectively target a broad range of plenum/wall spaces and allow for easy installations. Below plenum room side access to optical chamber and driver compartment via pressure removable radius lens and side panel. Luminaire is proudly manufactured in the U.S. Luminaire is painted after fabrication following treatment with phosphate rust inhibitor. Finish coating of housing reflecting surfaces is with highreflectance white (minimum 92%) polyester powder. Installation Luminaire installs by lifting it through grid ceiling and resting it on the T-bars. Luminaire installs onto standard 15/16 and narrow 9/16 T-grid ceiling systems. An accessory flange kit is available for installing into drywall or plaster. Warranty LSI LED Fixtures carry a 5-year warranty. 1 Year warranty on optional Battery Back Up. Test regularly in accordance with local codes. Listings Listed to UL 1598 and UL 875 for 25 C Ambient applications. IC Rated. RoHS Compliant. American Recovery and Reinvestment Act Funding Compliant. Lighting Facts Approved. Suitable For Damp Locations. Performance DELIVERED LUMENS* 3K 35K 4K 5K Efficacy Efficacy *LED Chips are frequently updated therefore values are nominal. Efficacy ELECTRICAL DATA* Watts 12V 28V 24V 277V 347V 2L L L L L L L L L L L L *Electrical data at 25C (77F). Actual wattage may differ by +/-1%. Efficacy Wattage 2L L L L L L L L L L L L RECOMMENDED LUMEN MAINTENANCE 1 Ambient Temp C hrs. 2 25K hrs. 2 5K hrs. 3 75K hrs. 3 1K hrs % 94.7% 91.7% 88.8% 85.99% 1 - Lumen maintenance values at 25 C are calculated per TM-21 based on LM-8 data and in-situ luminaire testing. 2 - In accordance with IESNA TM-21-11, Projected Values represent interpolated value based on time durations that are within six times (6X)the IESNA LM-8-8 total test duration (in hours) for the device under testing ((DUT) i.e. the packaged LED chip). 3 - In accordance with IESNA TM-21-11, Calculated Values represent time durations that exceed six times NA LM-8-8 total test duration (in hours) for the device under testing ((DUT) i.e. the packaged LED chip). APPLICATION REFERENCE* Spacing LPW W/FT2 Avg Fc # of Luminaires 32L 1' x 8' L 8' x 8' L 8'x 6' *Based on a 9' Mtg.Ht., 4K color Temp, 8/5/2 reflectances, 2.5' work plane, LLF:1., 4' x 4' Room LSI Industries Inc. 1 Alliance Rd. Cincinnati, OH (513) LSI Industries Inc. All Rights Reserved. 12/1/17
11 3/4 LPEC22 LED 45L UNV DIM1 35 F2 LPEC 2 x2 Luminaire Ordering Guide TYPICAL ORDER EXAMPLE: LPEC22 LED 32L UNV DIM1 4 ALC EM U Family/Size LED Gen LPEC22 - (2x2) LED 2L L L L L L L L L L L - 8 *Consult factory for programmable wattages and lumen packages. Lumen Package* Voltage Driver UNV V HV - 347V 1 DIM1 - Dims to 1% (-1 volt dimming) LDE1 - Hi-Lume 1% 4 (With Soft On Fade To Black) L3D -Lutron Hi-Lume 1% 4 LDE5 - Lutron 5-Series 4 SR - Sensor Ready 4 SD5 Step Dimming Driver to 5% Color Temperature Controls Options Packaging 3-3K 3,4 BLANK - (No Controls) EM1-1 watt Emergency Battery U - Single Pack 35-35K Backup JP - Job Pack 4-4K ALC - AirLink Controller 5-5K FC1-6 3/8 (3) #18 Leads (For Use ALOS - AirLink Controller In Non-Dimming Applications) w/ Occupancy Sensor FC15D - 6 3/8 (5) #18 Leads (For ALVS - AirLink Controller Use In Dimming Applications w/ Vacancy Sensor 9C - 9 CRI 3,4 Accessory Ordering Information (Accessories are field installed) Description Order Number Flange Kit 2x2 FK22 AirLink Control Accessories Wireless switches Catalog number Part Number Wireless Occupancy Sensors Part Number On/Off & Raise Lower ALWS 3B-(color)-KIT Wireless 36 4 ft², Ceiling Mount Wireless 18 3 ft², Wall Mount Wireless Photocell controls Catalog number Part Number Wireless 9 25 ft², Corner Mount On/Off & Dimming ALCM-W-PC 6249 Wireless, Hallway 15 ft Length Commission Laser Kit (See Laser warnings) Order as separate catalog number. Visit for complete listing of AirLink controls. Footnotes: 1 - Not available with AirLink 2 - Available colors are White, Ivory and Light Almond (WH, IV, LA) 3 - Consult Factory for lead times 4 - Consult with factory Photometry LPEC22 LED 32L 4 Luminaire photometry has been conducted by a NVLAP accredited testing laboratory in accordance with IESNA LM As specified by IESNA LM-79-8 the entire luminaire is tested as the source resulting in a luminaire efficiency of 1%. See for detailed photometric data ZONAL LUMEN SUMMARY ZONE LUMENS , , , , , , ,283.2 % OF LUMINAIRE LSI Industries Inc. 1 Alliance Rd. Cincinnati, OH (513) LSI Industries Inc. All Rights Reserved.
12 4/4 LPEC22 LED 45L UNV DIM1 35 F2 LPEC 2 x2 Controls enabled by Lutron AirLink is LSI s wireless indoor lighting control system. This fixture is compatible with the AirLink system & contains a factory-installed fixture controller (ALC) & sensor (ALOS/ALVS). For further information on these components, you can view their specsheets at Range Wireless Sensors & Controls must be located within 6ft (18m) line of sight or 3ft (9m) through walls of the associated control module Major motion: Movement of a person entering or passing through an area Minor motion: Movement of a person occupying an area and engaging in small activities (e.g., reaching for a telephone, turning the pages of a book, etc.) Ceiling Applications Small offices, conference rooms, lounges, classrooms Features Floor Minimum Light Level Setting (optional). Certain applications, such as hallways, may require that the lights never turn off. For these areas, select the minimum light level option and the load will lower to programed low-end level Daylighting dims lights down to OFF. Occupancy sensor must go unoccupied (vacant) in order for the fixture sensor to turn the lights off Occupancy sensor timeout (fixture sensor): 15 minutes Power failure memory: If power is interrupted, connected loads will return to the previous level Low-end trim adjustment (default is 1V or ballasts/drivers minimum for Lutron EcoSystem ballasts/drivers). High-end trim adjustment (default is 1V or 1% for Lutron EcoSystem ballasts/drivers) Includes integrated power measurement circuit that provides data to the wireless hub with +/_ 2% accuracy or.5w whichever is higher Passive infrared motion detection with exclusive Lutron XCT Technology for major and minor motion detection Up to 3 ft 2 (27.9 m 2 ) major motion coverage and 15 ft 2 (13.9 m 2 ) minor motion coverage & 36 field-of-view Daylight sensor has simple, automatic calibration straight out-of-the-box Designed to give a linear response to changes in perceived light level. Detects ambient light level changes from to 15 fc ( to 16 lx) 9.8ft (3m) 6.8ft (2.1m) 3ft 2 (28m 2 ) major motion 15ft 2 (14m 2 ) minor motion when mounted on a ceiling LSI Industries Inc. 1 Alliance Rd. Cincinnati, OH (513) LSI Industries Inc. All Rights Reserved. 12/1/17
13 1/4 LPEC24 LED 55L UNV DIM1 35 F3 Catalog # : Project : Prepared By : Date : Type : LPEC 2 x4 The LPEC s low profile design makes it ideal for shallow plenum applications. Best in class configurable lumen packages and efficiencies that target DLC Standard/ Premium. This fixture delivers even illumination with excellent, low angle brightness control throughout the space. Available in 1x4, 2x2, and 2x4. Features & Specifications Optical System High transmission impact resistant diffuse acrylic radius lens eliminates bright spots from individual LED s and provides high vertical illumination and visual comfort. Use of closely spaced medium-power, high brightness chips minimizes pixelation and provides uniform lens luminance. Available in 5K, 4K, 35K and 3K color temperatures. Minimum CRI of 8. Optional 9 CRI available, consult factory for lead times. Electrical High-performance driver features over-voltage, under voltage, short-circuit and over temperature protection. -1 volt dimming (1% - 1%) standard. Standard Universal voltage ( Vac) Input 5/6 Hz or optional High voltage (347Vac). L7 Calculated Life: >1k Hours (See Lumen Maintenance on Page 2) Total harmonic distortion: <2% Power factor: >.95 Input power stays constant over life. Optional 12v-277v integral emergency battery pack is available to meet critical life-safety lighting requirements. The 9-minute batteries provide constant power to the LED system, ensuring code compliance. A test switch/indicator button is installed in the housing for ease of maintenance. Controls LSI AirLink controls featuring Lutron Clear Connect makes each luminaire controllable, creating a wireless communication with other AirLink control devices such as dimmers, switches, occupancy sensors and photocontrols. The integrated sensor is both a passive infrared motion detector and photocell. See Page 2 for coverage diagram. Step-level dimming option allows system to be switched to 5% power for compliance with common energy codes while maintaining fixture appearance. Sensor Ready Drivers available; consult factory for limitations. Dimensions 5.36" (136mm) 4.815" (122mm) " (65mm) 1.5" (38mm) (AirLink Power Pack).545" 13.84mm) (AirLink Occupancy Sensor) 2.95" (74mm) 1.382" (35mm) 6.212" (158mm) 5.266" (134mm) (.875"K.O.) 2.95" (74mm) " (1212mm) 8.9" (25mm).547" (13.89mm) SIDE VIEW 8.31" (211mm) 2.516" (64mm) ARRA Funding Compliant " (1212mm) Optional AirLink Occupancy Sensor TOP VIEW " (1212mm) Acceess Plate Location Optional AirLink Power Pack BACK VIEW " (65mm) END VIEW 3.628" (92mm) " (65mm) LSI Industries Inc. 1 Alliance Rd. Cincinnati, OH (513) LSI Industries Inc. All Rights Reserved.
14 2/4 LPEC24 LED 55L UNV DIM1 35 F3 LPEC 2 x4 Features & Specifications (Cont.) Performance Construction Rigid housing is die-formed 2-gauge cold rolled steel for consistency and strength. End plates come equipped with integral NEC compliant earthquake clips. Ultra-slim < 3 luminaire height and lightweight design effectively target a broad range of plenum/wall spaces and allow for easy installations. Below plenum room side access to optical chamber and driver compartment via pressure removable radius lens and side panel. Luminaire is proudly manufactured in the U.S. Luminaire is painted after fabrication following treatment with phosphate rust inhibitor. Finish coating of housing reflecting surfaces is with highreflectance white (minimum 92%) polyester powder. Installation Luminaire installs by lifting it through grid ceiling and resting it on the T-bars. Luminaire installs onto standard 15/16 and narrow 9/16 T-grid ceiling systems. An accessory flange kit is available for installing into drywall or plaster. Warranty LSI LED Fixtures carry a 5-year warranty. 1 Year warranty on optional Battery Back Up. Test regularly in accordance with local codes. Listings Listed to UL 1598 and UL 875 for 25 C Ambient applications. IC Rated. DesignLights Consortium (DLC) Premium and/or standard qualified product. Not all versions of this product may be DLC qualified. Please check the DLC Qualified Products List at to confirm which versions are qualified. RoHS Compliant. American Recovery and Reinvestment Act Funding Compliant. Lighting Facts Approved. Suitable For Damp Locations. DELIVERED LUMENS* 3K 35K 4K 5K Efficacy Efficacy *LED Chips are frequently updated therefore values are nominal. Efficacy ELECTRICAL DATA* Watts 12V 28V 24V 277V 347V 3L L L L L L L L L L L *Electrical data at 25C (77F). Actual wattage may differ by +/-1%. Efficacy Wattage 3L L L L L L L L L L L RECOMMENDED LUMEN MAINTENANCE 1 Ambient Temp C hrs. 2 25K hrs. 2 5K hrs. 3 75K hrs. 3 1K hrs % 95.14% 92.57% 9.7% 87.64% 1 - Lumen maintenance values at 25 C are calculated per TM-21 based on LM-8 data and in-situ luminaire testing. 2 - In accordance with IESNA TM-21-11, Projected Values represent interpolated value based on time durations that are within six times (6X)the IESNA LM-8-8 total test duration (in hours) for the device under testing ((DUT) i.e. the packaged LED chip). 3 - In accordance with IESNA TM-21-11, Calculated Values represent time durations that exceed six times NA LM-8-8 total test duration (in hours) for the device under testing ((DUT) i.e. the packaged LED chip). APPLICATION REFERENCE* Spacing LPW W/FT2 Avg Fc # of Luminaires 48L 12' x 1' L 1' x 8' L 1'x 6' *Based on a 9' Mtg.Ht., 4K color Temp, 8/5/2 reflectances, 2.5' work plane, LLF:1., 4' x 4' Room LSI Industries Inc. 1 Alliance Rd. Cincinnati, OH (513) LSI Industries Inc. All Rights Reserved. 1/2/17
15 3/4 LPEC24 LED 55L UNV DIM1 35 F3 LPEC 2 x4 Luminaire Ordering Guide TYPICAL ORDER EXAMPLE: LPEC24 LED 48L UNV DIM1 4 ALC EM U Family/Size LED Gen LPEC24 - (2x4) LED 3L L L L L L L L L L L - 9 *Consult factory for programmable wattages and lumen packages. Lumen Package* Voltage Driver UNV V HV - 347V 1 DIM1 - Dims to 1% (-1 volt dimming) LDE1 - Hi-Lume 1% 4 (With Soft On Fade To Black) L3D -Lutron Hi-Lume 1% 4 LDE5 - Lutron 5-Series 4 SR - Sensor Ready 4 SD5 Step Dimming Driver to 5% Color Temperature Controls Options Packaging 3-3K 3,4 BLANK - (No Controls) EM1-1 watt Emergency U - Single Pack 35-35K Battery Backup JP - Job Pack 4-4K ALC - AirLink Controller 5-5K FC1-6 3/8 (3) #18 Leads ALOS - AirLink Controller w/ (For Use In Non-Dimming Occupancy Sensor Applications) ALVS - AirLink Controller w/ Vacancy Sensor FC15D - 6 3/8 (5) #18 Leads (For Use In Dimming Applications 9C - 9 CRI 3,4 Accessory Ordering Information (Accessories are field installed) Description Order Number Flange Kit 2x4 FK24 AirLink Control Accessories Wireless switches Catalog number Part Number Wireless Occupancy Sensors Part Number On/Off & Raise Lower ALWS 3B-(color)-KIT Wireless 36 4 ft², Ceiling Mount Wireless 18 3 ft², Wall Mount Wireless Photocell controls Catalog number Part Number Wireless 9 25 ft², Corner Mount On/Off & Dimming ALCM-W-PC 6249 Wireless, Hallway 15 ft Length Commission Laser Kit (See Laser warnings) Order as separate catalog number. Visit for complete listing of AirLink controls. Footnotes: 1 - Not available with AirLink 2 - Available colors are White, Ivory and Light Almond (WH, IV, LA) 3 - Consult Factory for lead times 4 - Consult with factory Photometry LPEC24 LED 48L 4 Luminaire photometry has been conducted by a NVLAP accredited testing laboratory in accordance with IESNA LM As specified by IESNA LM-79-8 the entire luminaire is tested as the source resulting in a luminaire efficiency of 1%. See for detailed photometric data ZONAL LUMEN SUMMARY ZONE LUMENS , , , , , , , , , , ,848.5 % OF LUMINAIRE LSI Industries Inc. 1 Alliance Rd. Cincinnati, OH (513) LSI Industries Inc. All Rights Reserved.
16 4/4 LPEC24 LED 55L UNV DIM1 35 F3 LPEC 2 x4 Controls enabled by Lutron AirLink is LSI s wireless indoor lighting control system. This fixture is compatible with the AirLink system & contains a factory-installed fixture controller (ALC) & sensor (ALOS/ALVS). For further information on these components, you can view their specsheets at Range Wireless Sensors & Controls must be located within 6ft (18m) line of sight or 3ft (9m) through walls of the associated control module Major motion: Movement of a person entering or passing through an area Minor motion: Movement of a person occupying an area and engaging in small activities (e.g., reaching for a telephone, turning the pages of a book, etc.) Ceiling Applications Small offices, conference rooms, lounges, classrooms Features Floor Minimum Light Level Setting (optional). Certain applications, such as hallways, may require that the lights never turn off. For these areas, select the minimum light level option and the load will lower to programed low-end level Daylighting dims lights down to OFF. Occupancy sensor must go unoccupied (vacant) in order for the fixture sensor to turn the lights off Occupancy sensor timeout (fixture sensor): 15 minutes Power failure memory: If power is interrupted, connected loads will return to the previous level Low-end trim adjustment (default is 1V or ballasts/drivers minimum for Lutron EcoSystem ballasts/drivers). High-end trim adjustment (default is 1V or 1% for Lutron EcoSystem ballasts/drivers) Includes integrated power measurement circuit that provides data to the wireless hub with +/_ 2% accuracy or.5w whichever is higher Passive infrared motion detection with exclusive Lutron XCT Technology for major and minor motion detection Up to 3 ft 2 (27.9 m 2 ) major motion coverage and 15 ft 2 (13.9 m 2 ) minor motion coverage & 36 field-of-view Daylight sensor has simple, automatic calibration straight out-of-the-box Designed to give a linear response to changes in perceived light level. Detects ambient light level changes from to 15 fc ( to 16 lx) 9.8ft (3m) 6.8ft (2.1m) 3ft 2 (28m 2 ) major motion 15ft 2 (14m 2 ) minor motion when mounted on a ceiling LSI Industries Inc. 1 Alliance Rd. Cincinnati, OH (513) LSI Industries Inc. All Rights Reserved. 1/2/17
17 1/1 EXC R U WB XXX SD2 EX EXC - Cast Aluminum LED Exit height = 8-1/2" Width = 12-3/4" Depth = 2" (single face) Depth = 2-1/4" (Double Face) Housing Enclosure, Face Plate, Back Plate & Canopy Constructed of Precision Die Cast Aluminum Universal Housing Design Includes 2nd Face Plate and Canopy Damp Location Rated Knock-out Style Chevron Arrows Standard Finishes are White, Black, or Brushed Aluminum Fixture may be built to comply with the ARRA Act of 29 and Buy American Provisions, consult factory. Illumination L.E.D. source - available in long life, high output red or green Low Energy consumption. Fully Illuminated 6 Inch Letter with ¾ Stroke Electronics 12/277 Dual Voltage with Test Button and LED AC/DC Indicator Light Overload & Short Circuit Protection Voltage Surge & Brown-out Protection Solid State Constant Current Charger with over-charge protection. Flasher & Buzzer Options Provides ADA Compliance Battery 6 volt Ni-Cad Battery Standard Mounting Universal Mount with Canopy Universal J-Box Mounting Pattern Code Conformance & Standards UL 924 N.E.C. OSHA N.F.P.A. Life Safety Code 11 ETL listed 9min. run time/12 hr. recharge time Wire guard available. Order separately. See wire guard chart in Accessories section. ordering InFormaTIon TYPICAL ORDER EXAMPLE: EXc r - u LB BL sd2 Prefix Letter color character size number of Faces Battery Housing / Face options EXC R - Red BLANK = 6 U - Universal LB-Less Battery BL-Black w/aluminum Face SD2 - Self Test / Self Diagnostics 1 G - Green Includes 2 Face Plates, BB-Black w/black Face DLT - Downlight Back Plate, And WB-With Battery WW-White w/white Face IF - Alarm Interface With Flasher Mounting Canopy BA-Brushed Aluminum w/alumi. Face IFA - Alarm Interface W/flasher & Audible Alarm VL - Vandal Lens FL - Flasher AA - Audible Alarm FA - Flasher / Audible Alarm 2CI - Two Circuit Input PG - (*) Polycarb Guard (See Chart) TRH - Tamper Resistant Hardware TRT8 - Tamper Resistant Tool US - Meets Buy American Requirements 1 - Not available without battery (LB) option. Project Name Catalog # Fixture Type 2/19/ LSI INDUSTRIES INC.
BAS SFP22 Edge-lit LED Panel
Project Name Fixture Type Catalog # BAS SFP22 The ultra-thin, edge-lit LED panel (BAS SFP22) series is designed to deliver general ambient lighting in a variety of indoor settings, including schools, offices,
More informationSDL4 LED Strip Diffused Lens
Catalog # : Project : Prepared By : Date : SDL4 The sleek architectural SDL is designed with tooless entry features saving time and money on installation. Optimizing industry leading LED technology, the
More informationDimensions (111mm) 3 (76mm) (111mm) (48mm)
Catalog # : Project : Prepared By : Date : S2 The sleek architectural S is designed with tooless entry features saving time and money on installation. Optimizing Industry LED technology, the S series delivers
More informationBAS SDL8' LED Strip Diffused Lens
Project Name Fixture Type Catalog # BAS SDL8' The sleek architectural SDL is designed with tooless entry features saving time and money on installation. Optimizing industry leading LED technology, the
More informationDimensions (111mm) (111mm) 3 (76mm)
Catalog # : Project : Prepared By : Date : S8 The sleek architectural S is designed with tooless entry features saving time and money on installation. Optimizing industry leading LED technology, the series
More informationLHBXD LED Linear High Bay
Catalog # : Project : Prepared By : Date : LHBXD The LHBXD is the perfect solution for a wide variety of applications and mounting heights. It s competitive pricing, multiple lumen packages, and high ambient
More informationAlliance 4 - ALI4 LED 4 Linear High Bay
Catalog # : Project : Prepared By : Date : Alliance 4 - ALI4 The new Alliance indoor LED high bay was designed to provide flexibility on any project. For use with applications ranging from school gymnasiums
More informationFixture Controller. Applications. Features. Specifications. Certifications & Affiliations. Catalog #: ALC/ALCE Part #: /
Project name Prepared by Date INDOOR AIRLINK LUTRON Catalog #: ALC/ALCE Part #: 624087/634480 The ALC/ALCE wireless fixture controller is a radio-frequency (RF) device that controls the 0 10V or Lutron
More informationLUMINAIRE ID SIZE CENTER OPTICS SIDE OPTICS LIGHT SOURCE CRI LUMEN PACKAGES COLOR TEMP. VOLTAGE. LED - high performance LED 80-80CRI 90-90CRI
PROJECT: APPROVED BY: SIGNATURE: Grid - shown with a Nova flat lens Grid - shown with a Nova Slope lens TYPE QTY DESCRIPTION Nova is an efficient architectural LED troffer with a distinctive luminous shielding
More informationEvolution EXWW RECESSED LINEAR WALL WASH LUMINAIRE
Evolution EXWW Project Name Date Type RECESSED LINEAR WALL WASH LUMINAIRE 3-13/16 (96.8mm) 5-1/8 (130.2mm) Extruded aluminum trim with formed cold rolled 20 gauge steel back box housing Highly reflective,
More informationRecessed. DuaLED 2x , 2700, 3000, 3400, 3800, or 4400lm
Recessed Dua 2x2 Project: Location: Cat.No: Type: Lamps: Notes: Qty: 2100, 2700, 3000, 3400, 3800, or 4400lm Philips Day-Brite / Philips CFI Dua recessed is a highly efficient, visually comfortable, architecturally
More informationDHL-LP-LED Low Profile LED Linear High/Low Bay
Job Information Type: Catalog #: Project: Comments: Prepared by: WARRANTY WARRANTY YEAR TEN INCLUDES LABOR ALLOWANCE 2 65W/90W Version 23.81 2 135W Version For 4 dimensions see pg 2 23.81 23.81 23.81 12.6
More informationDRD5S & SurfaceFrame Alt/EM Surface Mount LED Downlight
DRD5S & SurfaceFrame Alt/EM Project: Product Code: Type: Date: Spec Sheet V- 11.15.18 Maintains all the standard SurfaceFrame ratings Offers enhanced dimming protocol compatibility including Lutron Hi-Lume
More informationCatalog # Project. Comments. Prepared by. Warranty Five year warranty
DESCRIPTION The Converge series by Neo-Ray defines the new standard in ambient lighting by combining the highest degree of minimization with the most advanced optical distribution and control available.
More informationPioneering Petroleum Canopy Lighting Since 1976
Pioneering Petroleum Canopy Lighting Since 1976 1976 LSI enters canopy lighting market 1995 2007 2008 Scottsdale Crossover 50 Crossover 100 2009 CRO3 2011/2012 CRS/CRS Gold 2013 CRU 2014 CRUS When LSI
More informationCPPG ENERGY EFFICIENT CANOPY LIGHTS FOR PARKING AREAS
ENERGY EFFICIENT CANOPY LIGHTS FOR PARKING AREAS ENERGY EFFICIENT CANOPY LIGHTS FOR PARKING AREAS PROJECT TYPE YEAR WARRANT Y Prodigy's canopy lights offer a unique combination of energy efficiency, reliability
More informationMetalux SWLED LED. Type. Catalog # Project. Date. Comments. Prepared by
DESCRIPTION is a versatile LED surface or wall mount luminaire which can be used in a broad range of commercial and industrial applications. This series provides customers with a high quality luminaire
More informationVESICA LINEAR SUSPENDED VES L
PROJECT INFORMATION Project Name Catalog # VESICA LINEAR SUSPENDED APPLICATIONS Office Spaces Conference Rooms Municipal Facilities Medical Facilities Type Date Financial Institutions Retail Spaces Hospitality
More informationCeiling-Mounted Wireless Occupancy/Vacancy Sensor
Project name Prepared by Date INDOOR AIRLINK enabled by Lutron Catalog #: ALW OS/VS CM Part #: 624094 624615 The Ceiling-Mounted Wireless Occupancy & Vacancy Sensors are wireless, battery- powered, passive
More informationProject Name. Date. Cat. Number. Type
HT1 Series LED High Output Troffer High output, interior troffer design used in high ceiling applications requiring superior lumen output, ultra-long life and high quality of light. Project Name Date Cat.
More informationlight ACL9 ANATOMY PERIMETER FOCUSED INSTALLATION SLEEK & STRONG
ACL9 ACL9 ANATOMY SLEEK & STRONG A stylish rectilinear aluminum extrusion made of 60% recycled material provides ultimate durability and functionality. 3.325 2.25 0.63 PERIMETER FOCUSED INSTALLATION A
More informationDRD5S & SurfaceFrame Alt/EM 18" Linear Surface Mount LED Area Light
DRD5S & SurfaceFrame Alt/EM 18" Linear Surface Mount LED Area Light Project: Product Code: Type: Date: Spec Sheet V- 04.15.19 Maintains all the standard SurfaceFrame ratings Offers enhanced dimming protocol
More informationCatalog Number. Notes
Catalog Number FEATURES & SPECIFICATIONS INTENDED USE The BLT Best-in-Value Low Profile LED luminaire features a popular center basket design that offers a clean, versatile style and volumetric distribution.
More informationVive PowPak Fixture Controls
Vive 369918g 1 03.12.18 The PowPak wireless fixture control is a radio-frequency (RF) device that controls either the Lutron EcoSystem or 0 10 V- electronic fluorescent ballasts and LED drivers (depending
More informationStep-Dimming and/or 0-10v Dimming Drivers Electro Galvanized Steel Welded Construction. Photocell Sensor - On/Off Stainless Steel Fasteners Standard
rev. 2//2 SECURITY - LED BCL1 SERIES Canopy, Stairwell & Passageway Luminaire The BCL1 series is a surface mounted luminaire designed for Stairwells, passageways, canopies, corridors, pedestrian tunnels
More informationRECESSED T-Bar & Drywall
Project Type Notes Curved Rectilinear PERFORMANCE AT 3500K NOMINAL LUMEN OUTPUT INPUT WATTS* EFFICACY 580 lm/ft 6.3 W/ft 95 lm/w Please consult factory for customize lumen output and wattage. 3 1 /2 3
More informationProject Name. Date. Cat. Number. Type
Linear Series 2.0 LED linear luminaires and retrofit linear kits The Linear Series delivers ultra-long life and high efficacy. Fixtures can be installed independently or joined together for continuous-run
More informationCatalog Number. Notes. Type. FST Snap on frosted, diffuse L/LENS No diffuser
Catalog Number FEATURES & SPECIFICATIONS INTENDED USE Built on the compact, low-profile Z strip channel, this LED strip offers long maintenance-free life, several color s, lumen outputs and lengths. Ideal
More informationFPLHB - Fidelux Premier Linear Highbay
FPLHB - Fidelux Premier Linear Highbay Product Description Fidelux LED Linear High Bays meet the challenging maintenance, safety, and performance requirements of industrial environments through an unbeatable
More informationM60 LED Recessed Wet Location
Date: Customer: Project: Type: Qty: M60 Order Code: - - - - - - - - - - Series L60W Multi-Mount Form L6WR Continuous Flange (Flanged Endcaps) L6WR Continuous Flange (Flangeless Endcaps) Light Engine B,,
More informationVIENTO MEDIUM AREA & SITE LED LUMINAIRE OPTICS
PROJECT INFORMATION Project Name Date VIENTO MEDIUM Catalog # APPLICATIONS Auto Dealership Sales Lots Parking Lots Educational/Business Campuses Type Parks & Recreation Areas Security Areas Mall & Retail
More information*REPRESENTS 3500K/80CRI 2 FT 4 FT 6 FT 8 FT 2 FT 4 FT 6 FT 8 FT *REPRESENTS 3500K/80CRI LINEAR
SUSPENDED SYSTEM The ELEMENT Merge Suspended LED linear system represents the marriage of indirect downlight, independent up light, and a track system; all in one system with independent control and outputs
More informationAlbeo LED Luminaire. Heavy Industrial Low Bay Lighting. (ALR1 - Series)
Albeo LED Luminaire Heavy Industrial Low Bay Lighting (ALR1 - Series) Product Features The Albeo ALR1-series LED luminaire is an energy-efficient, low maintenance alternative to traditional fluorescent
More informationM-LED for 4 Technical Ceilings Recessed Linear LED for 4 Technical Ceiling Systems
Date: Customer: Project: Type: Qty: M-LED for 4 Technical Ceilings Order Code: LR4TZ - - - LW - TBZ - - - - - - LR4TZ Series LR4TZ M-LED for 4 Technical Ceiling Systems - Light Engine 1B45 1,2 713lm/10.8W
More informationStocking Solutions. Downlights LED Panels Floods & Wall Packs
Stocking Solutions Downlights LED Panels Floods & Wall Packs Because Experience Makes the Difference Since 1976, LSI Industries has been introducing smart, innovative lighting solutions to help its customers
More informationCatalog Number. Notes
Catalog Number FEATURES & SPECIFICATIONS INTENDED USE The BLT Best-in-Value Low Profile LED luminaire features a popular center basket design that offers a clean, versatile style and volumetric distribution.
More informationLHB LED High Bay. Technical Specifications. Description. Performance Data. Dimensions & Weights. Delivered Lumens Efficacy.
Technical Specifications Description The High Bay luminaire delivers the illumination performance to replace up to a 400W HID fixture one-for-one. Lumecon s unique High Bay design makes this fixture an
More informationMEDLEY A. RoHS COMPLIANT INTERIOR - INTEGRAL POWER SUPPLY WHITE LIGHT & STATIC COLORS SHAPING THE EXPERIENCE OF LIGHT
LINE VOLTAGE LED, INTERIOR LINEAR LIGHTING Ideal for ceiling and wall washes Integral power (line voltage 120V 277V) Wireless DMX capability Field installable accessories LIGHT SOURCE 3.5W/FT, 7W/FT, 11W/FT,
More informationDIMMING 0-10V Continuous
Project Notes Type Date Cat. No. SLB XE Series Slim Linear LED High Bay DESCRIPTION The Aleo SLB XE G3 and SLB XE G3 ECO Series Slim Linear High Bay delivers industryleading performance with an extremely
More informationCatalog # Project. Comments. Prepared by. 23-3/4" [603mm] LAMP CONFIGURATIONS. 3-1/4" [83mm] X=2-7/16" [62mm] Y=2-1/2" [64mm] CEILING COMPATIBILITY
DESCRIPTION The Encounter redefines ambient lighting by being the first fixture to blend modern contemporary styling with the innovative WaveStream technology to deliver exceptional performance and superior
More informationBAYMAX TM LED LINEAR HIGHBAY FIXTURE BLHT SERIES
PROJECT NAME: CATALOG NUMBER: NOTES: FIXTURE SCHEDULE: Page: 1 of 5 BAYMAX TM LED LINEAR HIGHBAY FIXTURE FEATURES: High Efficacy LED boards with dual copper cladding for thermal dissipation 1-1V Dimming
More informationGrüv Flare Regressed. Recessed Linear LED
Grüv Flare Regressed Features The Gruv Flare Regressed fixture provides high-performance, visually comfortable, high efficient ambient lighting. Designed with a regressed lens and a flared aperture, the
More informationACL 4 ANATOMY. COVER UP Partially diffuse dust cover enhances indirect lighting performance and preserves LED lifespan. 1.87
ANATOMY COVER UP Partially diffuse dust cover enhances indirect lighting performance and preserves LE lifespan. 1.87 MULTIFACETE ISTRIBUTION Versatile design application is achieved through selection of
More informationMillenium Os. Luminaire LED. For Stairwells and Public Spaces. Designed and manufactured in the USA. High Abuse Motion-Activated Lighting Product
Millenium Os For Stairwells and Public Spaces High Abuse Motion-Activated Lighting Product HA Designed and manufactured in the USA Occupancy Sensors Just Make Sense As industry standards continually change
More informationWireless Indoor Lighting Control System
enabled by Lutron Wireless Indoor Lighting Control System Lutron the image company TM enabled by Lutron simple to specify simple to install simple to use 2 AirLink Simple to specify The flexibility you
More informationTROFFER RETROFIT KIT (TRK)
Not all products are qualified on the DLC QPL. To view our DLC qualified products, please consult the DLC Qualified Products List at www.designlights.org/qpl. TROFFER RETROFIT KIT (TRK) www.trulygreensolutions.com
More information4 LED Recessed Adjustable. Energy efficient, stylish downlighting for residential and commercial applications
4 LED Recessed Adjustable Energy efficient, stylish downlighting for residential and commercial applications The most efficient, stylish, high-performance downlight is now adjustable Juno Generation 4
More informationEvolve LED Garage Light
GE Lighting Evolve LED Garage Light (EG2R) imagination at work Product Features High quality lighting meets long life and controllability with the Evolve LED Garage Light, EG2R. This fixture features an
More informationRECESSED - WITH StepLens OPTION
Project Type Notes PERFORMANCE PER LINEAR FOOT AT 4K Flush shielding option Flush StepLens option Regressed NOMINAL LUMEN OUTPUT INPUT WATTS* EFFICACY 4 lm/ft 3.7 W/ft 19 lm/w 5 lm/ft 4.6 W/ft 18 lm/w
More informationCatalog Number. Notes
Catalog Number FEATURES & SPECIFICATIONS INTENDED USE Built on the compact, low-profile Z strip channel, this LED strip offers long maintenance-free life, several color s, lumen outputs and lengths. Ideal
More informationEssentials Series 4.0
Essentials Series 4.0 LED High Bay Essentials Series 4.0 provides the highest quality, reliability and performance with extraordinary lumen maintenance and efficacy, delivering superior ROI for your application.
More informationLED FLAT PANEL EDGE LIT MLFP SERIES G2
PROJECT NAME: CATALOG NUMBER: NOTES: FIXTURE SCHEDULE: LED FLAT PANEL EDGE LIT SERIES G2 1x4 2x2 Page: 1 of 6 PRODUCT DESCRIPTION: Typically used to replace 1 x4, 2 x2 and 2 x4 fluorescent fixtures, the
More informationGrüv Flare Regressed. Recessed Linear LED
Grüv Flare Regressed Features The Gruv Flare Regressed fixture provides high-performance, visually comfortable, high efficient ambient lighting. Designed with a regressed lens and a flared aperture, the
More informationPerformance Chart Electrical Data
Evoke Spot Glow 12 Features The Evoke Spot Glow offers the best of accent and ambient lighting in one unique, multi-functional, recessed square-in-square fixture. Featuring a 2.9 13W or 18W LED downlight
More informationQty: L lm/12.6W K. DC3 Lutron 3-Wire. DMD eldoled DALI. DC2 5 Lutron 2-Wire
Date: Customer: Project: Type: Qty: Cerro LED Order Code: CERLR - - - - - - - - - CERLR Series CERLR Cerro LED Light Engine 1L105 3210lm/37.8W 1L90 1L70 1L50 2751lm/32.4W 2140lm/25.2W 1529lm/18.0W 1L35
More informationSOL CROSS SECTION. PENDANT Spec Guide. Page 2 of Rev. JUNE18-1
SOL PENDANT CROSS SECTION Page 2 of 10 260.599.3590 orders@luxilluminaire.com www.luxilluminaire.com SPECIFICATION Lux Illuminaire pairs long life name brand LED chips and boards to ensure the highest
More informationSPECIFICATIONS HYLYTR. with DOUBLE SLOT OPTICS
HYLYTR with DOUBLE SLOT OPTICS (HYWG) Recessed, Perimeter, Mud-In LED MULTI-GRAZER (HYMG) Surface LED SHOWCASER (HYSC) Recessed, Suspended LED HYWGR HYMG HYSCS HYMG HYWGRP Find additional images and information
More informationMax 4 Flush Lens RECESSED
Overview Flush 4 inch LED linear snap-in lens Sleek, slender contemporary design Easy to install T-Grid, S-Slot Grid, Tech Zone Ready Special - no light leak ends feature Ordering Format PART NUMBER: MX4-F
More informationMetalux 4WSL / 8WSL LED
DESCRIPTION The new Metalux WSL - Linear with Wavestream technology series redefines linear ambient lighting by offering a balance of the modern contemporary styling with the innovative WaveStream technology
More informationMetalux 4WSL / 8WSL LED
DESCRIPTION The new Metalux WSL - Linear with Wavestream technology series redefines linear ambient lighting by offering a balance of the modern contemporary styling with the innovative WaveStream technology
More informationProject: Comments: Prepared By: Control. Code Fixture & Trim D3 Wall Wash, Round. Platform & Control Wide Gamut, Tunable
Project: Comments: Prepared By: Tunable, fixture produces a wide range of 90+ CRI/R9 whites from 1400K-10,000K, as well as pastels and saturated colors Closed-loop color point maintenance to
More informationCatalog Number. Notes. Type ADP. Series Air function Lumens Diffuser Voltage Driver Color temperature. Acrylic linear prismatic
Catalog Number FEATURES & SPECIFICATIONS INTENDED USE The VT Series Volumetric Troffer (VTL) combines the aesthetics and high performance with intelligent engines for applications such as offices, schools,
More informationRECESSED Spec Guide. up to 111 lm/w performance
RECESSED up to 111 lm/w performance Performance based on 4 luminaire at 4000K @ 25 o C Calculated L80 at 80,000 hours Lumens per foot are delivered lumens Page 2 of 10 260.599.3590 orders@luxilluminaire.com
More informationSECTION INTERIOR LIGHTING
SECTION 26 51 00 INTERIOR LIGHTING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSECTION INTERIOR AND EXTERIOR LIGHTING FIXTURES
SECTION 26 50 00 INTERIOR AND EXTERIOR LIGHTING FIXTURES PART 1: GENERAL 1.1 WORK INCLUDED: A. Interior lighting fixtures and accessories B. Exterior lighting fixtures and accessories C. Emergency battery
More informationNightfall. led emergency egress lighting
Nightfall led emergency egress lighting Nightfall led emergency egress lighting Combining a sleek, architectural, low profile design with high performance makes the Nightfall Series an attractive LED solution
More informationEtch 2' x 2' Recessed LED
Etch 2' x 2' Open Regressed Panel Features Upgrade your ambient lighting designs with ETCH 2' x 2', an exciting fresh vocabulary combining ambient and accent lighting for creating dynamic lighting compositions
More informationAPPLICATIONS SPECIFICATION FEATURES ORDERING. Project: Notes: Catalog #: Large Outdoor Spaces. Swimming Pools. Shopping Malls. Large Indoor Spaces
Project: Notes: Type: Catalog #: Date: LED UFO HIGHBAY PT-HBA-100W SERIES APPLICATIONS Large Outdoor Large Indoor Industrial Areas Churches Swimming Pools Shopping Malls Warehouses Commercial Gymnasiums
More informationSuite: Foyer/Hallway/Closet PROJECT: ZIGG CONDOS TYPES ' S1 ' & ' S6 ' Description: Flush Mount lass. Finish: Diameter: " Height: 4" Lamp: x
Suite: Foyer/Hallway/Closet PROJECT: ZIGG CONDOS TYPES ' S1 ' & ' S6 ' Description: Flush Mount lass Finish: Diameter: " Height: 4" Lamp: x 352-(&7 =,** &21'26 7
More informationProduct Overview. Fixture Type. Performance Chart. Wattage. Electrical Data 23W System Watts Amps
2000 LM Round Downlight Product Overview Features Essenza HP LED Downlights are designed to deliver high punch of light for high ceilings and high ambient applications. The shallow frame (only -1/8" plenum
More informationHIGH POWER LED RETROFIT MODULE
LEDBLOCK G3 HIGH POWER LED RETROFIT MODULE The LEDBLOCK is a patented extruded aluminum design that replaces HID, HPS, or MH lamps. The installation bracket of the LEDBLOCK G3 comes partially assembled
More informationWARRANTY LED ECO PANEL.
LED ECO PANEL www.trulygreensolutions.com 8 MODELS AVAILABLE IN 25W TO 72W EXPECTED LIE OVER 50,000 HRS Compatible Emergency Battery Backup Available eatures 5 YEAR Suitable or Damp Location Use IES ILES
More informationLED RETROFIT CONVERSION KITS
Our LED RetroFit Conversion Kits come with a complete Gear Tray Assembly to convert older 4-foot and 8-foot T8 or T12 strip-type fixtures into energy efficient LED luminaires. High quality components and
More informationLED ECO PANEL.
Not all products are qualified on the DLC QPL. To view our DLC qualified products, please consult the DLC Qualified Products List at www.designlights.org/qpl. LED ECO PANEL www.trulygreensolutions.com
More informationIHOL-6DS / ISD600 6 Gravity LED Square Downlight
IHOL-6DS / ISD600 6 Gravity LED Square Downlight JOB ELECTRICAL DATA LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** M1 M2 L1 L2 L3 L4 L5 12W 25W 34W 46W 59W 75W 93W * System Wattage include
More informationCapella 2. Project Name. Construction. Optical System. Product Applications. Housing and lens frame are constructed from heavy-duty low
Product # Type Date Project Name Project Location Prepared By Capella 2 Construction Y Housing and lens frame are constructed from heavy-duty low Glass Lens is Minimum 1/8 thick thermal and impact resistant
More informationM100 My White LED Direct Tunable White
Date: Customer: Project: Type: Qty: M00 My White Tunable White Order Code: L0 - A2 - - - - - - - - - - TW L0 A2 Series L0 M00 Light Engine A2 68lm/8.6W per foot Average values calculated from a fixture
More information11.4 lbs (5.2 kg) 13.2 lbs (6 kg) 17.6 lbs (8 kg) ORDERING INFORMATION MODEL LED COLOR TEMP. VOLTAGE LED DRIVER. 4000K (80 CRI) (Std.
LB APPLICATION The LED igh Bay is the lighting solution for a wide variety applications that require specific mounting heights. Precision-designed optics, multiple distributional options, lumen outputs
More informationIHOL-6DR / IRD600 6 Gravity LED Downlight
IHOL-6DR / IRD600 6 Gravity LED Downlight JOB ELECTRICAL DATA LED Light Engine System Wattage * CCT / CRI Delivered Lumens ** M1 M2 L1 L2 L3 L4 L5 12W 25W 35W 46W 60W 75W 93W * System Wattage include driver
More informationSURFACE Spec Guide. up to 105 lm/w performance
SURFACE SURFACE Spec Guide up to 105 lm/w performance Performance based on 4 luminaire at 4000K @ 25 o C Calculated L80 at 80,000 hours Lumens per foot are delivered lumens Page 2 of 10 260.599.3590 orders@luxilluminaire.com
More informationPRODUCT DATA SHEET LIGHTING PRODUCTS
EPCO s LED s are available in nineteen (19) configurations that are vapor tight, provide unparalleled performance, improved efficacy, more lumens per watt, and are the reliable, sustainable solid-state
More informationFino Healthcare. Asymmetric Wall Mount Indirect LED
Fino Healthcare Asymmetric Wall Mount Indirect LED Features fiture is ideal for applications requiring a wipe down lens with no horizontal "shelf" surfaces. Designed with an integrated acrylic lens to
More informationCLM 422 Series LED Ceiling Luminaire Module - 45Watt
Product Information The CLM422 LED Ceiling Luminaire Module is the first truly engineered commercial grade (2'x 2') LED office light designed to replace fluorescent fixtures of much higher wattage classes.
More informationlumenalpha downlight Specification Sheet
Client Project name Order# Type Qty FEATURES AND BENEFITS Physical Housing material: aluminum housing Reflector material: metallized polycarbonate Trim finish: white, black, gray or custom RAL color Fixed
More informationEssenza. Square Downlights
Downlight Adjustable Features Essenza LED Downlights are designed to deliver the features required for your Hotel and Residential High Rise or Commercial projects. Available with 12W or 18W LED modules,
More informationPerformance Chart Electrical Data
Features The Rook 4 Pendant translates the control, performance, and comfort of our downlights into a sophisticated new format. The 4 pairs perfectly with the Evoke 4. Downlight. The Rook is perfect for
More informationA. Furnish and install wiring devices and plates as specified herein and as shown on the Drawings.
DIVISION 26 ELECTRICAL SECTION 26 27 26 PART 1 GENERAL 1.01 DESCRIPTION A. Furnish and install wiring devices and plates as specified herein and as shown on the Drawings. B. Specialty switches and outlets
More informationIHOL-8DS / ISD802 8 Gravity LED Square Downlight with Regressed Lens - Wet Location
IHOL-8DS / ISD802 8 Gravity LED Square Downlight with Regressed Lens - Wet Location JOB NAME 8 5/8 5 1/16 10 7/16 14 9/16 15 1/8 4 3/4 7 7/8 9 Housing Specification: Trim Specification: Ceiling Cut Out:
More informationClaude Indirect Wall WALL
Overview Aesthetically pleasing design with no visible screws and a sleek cross section for minimal appearance (2 inch) One piece extruded aluminum housing with integral driver Indirect lighting only Continuous
More informationFULL BLEED APPLICATION SHOT RENDERING
FULL BLEED APPLICATION SHOT RENDERING ANATOMY SLEEK & STRONG A perfectly square aluminum extrusion made of 60% recycled material provides durable functionality in an elegant compact form. CORE CAPACITY
More informationPerformance Chart Electrical Data
Pendant Features High style, yet also versatile. Spare and modern, yet warm and welcoming. This striking Rook 35 re-imagines the Hornet HP Downlight line in a popular new pendant form. It s a fabulous
More informationPerformance Chart Electrical Data
Features The Rook 4 Pendant translates the control, performance, and comfort of our downlights into a sophisticated new format. The 4 pairs perfectly with the Evoke 4. Downlight. The Rook is perfect for
More informationHIGH LUMINOUS EFFICIENCY
Warehouses, factories, and other industrial facilities have always relied on high bay lighting to provide bright light to large spaces. Now, ASD offers an all-in-one solution to these lighting applications.
More information3.75 Gyro Shift Multiples Single Head
CATALOG#: PROJECT: FIXTURE TYPE: CONTACT: PHONE: Wattage CCT Delivered Lumens Efficacy 10W 3000K 966lm 97lpw 15W 3000K 1437lm 96lpw 20W 3000K 1739lm 87lpw 25W 3000K 2049lm 82lpw 30W 3000K 2254lm 75lpw
More informationEvoke 2.9" HP. 2.9" Round Lens Wall Wash
Evoke.9" HP Lens Wall Wash Features Evoke.9 LED fixtures are now available with a higher performance LED module providing W, 8W or 0W of lighting power. Featuring the fit, finish and attention to detail
More informationRating. Class I Div II
TYPE: LED HAZGLOBE : HZ2 LARGE - 26 WATT SPECIFICATIONS. Housing and Lens Frame: Die cast aluminum for thermal management Lens: Tempered Glass Cage: 0.25 dia Wire; 304 stainless steel Finish: TGIC thermoplastic
More informationIBLED SERIES 4' PROJECT: FEATURES AND SPECIFICATIONS LINE DRAWING
PAGE OF 5 MODEL: PROJECT: PREPARED BY: DATE: TYPE The IBLED series LED high bays are ideal for manufacturing, warehousing, commercial and industrial facility lighting applications. The superior design
More informationIOTA Exit Signs. IOTA Emergency Fixtures
IOTA Exit Signs IOTA Exit Signs offer a variety of models to meet your interior egress requirements. IOTA Exit solutions are designed and manufactured for efficient, long-lasting performance, easy installation,
More informationEssenza. Round Downlights
Downlight Adjustable Product Overview Features Essenza LED Downlights are designed to deliver the features required for your Hotel and Residential High Rise or Commercial projects. Available with 12W or
More informationIHOL-S4DR / IRDS400 4 Gravity LED Shallow Downlight
IHOL-S4DR / IRDS400 4 Gravity LED Shallow Downlight JOB ELECTRICAL DATA LED Light Engine Delivered Lumens * System Wattage ** M1 M2 L1 L2 L3 900lm @ 3000K / 82 CRI 1750lm @ 3000K / 82 CRI 2400lm @ 3000K
More information